A comparative study for petroleum removal capacities of the bacterial consortia entrapped in sodium alginate,sodium alginate/poly(vinyl alcohol),and bushnell haas agar

The purpose of this study was to identify and compare the degradation efficiencies of free and entrapped bacterial consortia(Staphylococcus capitis CP053957.1 and Achromobacter marplatensis MT078618.1)to different polymers such as Sodium Alginate(SA),Sodium Alginate/Poly(Vinyl Alcohol)(SA/PVA),and Bushnell Haas Agar(BHA).In addition to SA and SA/PVA,which are cost-effective,non-toxic and have different functional groups,BHA,which is frequently encountered in laboratory-scale studies but has not been used as an entrapment material until now.Based on these,the polymers with different surface morphologies and chemical compositions were analyzed by SEM and FT-IR.While the petroleum removal efficiency was higher with the entrapped bacterial consortia than with the free one,BHA-entrapped bacterial consortium enhanced the petroleum removal more than SA and SA/PVA.Accordingly,the degradation rate of bacterial consortia entrapped with BHA was 2.039 day^(-1),SA/PVA was 1.560,SA was 0.993,the half-life period of BHA-entrapped bacterial consortia is quite low(t_(1/2)=0.339)compared with SA(t_(1/2)=0.444)and SA/PVA(t_(1/2)=0.697).The effects of the four main factors such as:amount of BHA(0.5,1,1.5,2,2.5,3 g),disc size(4,5,6,7,8 mm),inoculum concentration(1,2.5,5,7.5,10 mL),and incubation period on petroleum removal were also investigated.The maximum petroleum removal(94.5%)was obtained at≥2.5 mL of bacterial consortium entrapped in 2 g BHA with a 7 mm disc size at 168 h and the results were also confirmed by statistical analysis.Although a decrease was observed during the reuse of bacterial consortium entrapped in BHA,the petroleum removal was still above 50%at 10th cycle.Based on GC-MS analysis,the removal capacity of BHA-entrapped consortium was over 90%for short-chain n-alkanes and 80%for medium-chain n-alkanes.Overall,the obtained data are expected to provide a potential guideline in cleaning up the large-scale oil pollution in the future.Since there has been no similar study investigating petroleum removal with the bacterial consortia entrapped with BHA,this novel entrapment material can potentially be used in the treatment of petroleum pollution in advanced remediation studies.

Pretreatment of poly(acrylic acid) sodium by continuous diafiltration and time revolution of filtration potential

The pretreatment for the removal of small molecules from poly(acrylic acid) sodium (PAAS) solution by continuous diafiltration was investigated using ultrafiltration membrane. The effects of PAAS concentration, pH, trans-membrane pressure and pretreatment time on the permeate concentration and permeate flux were studied. The results show that the necessary pretreatment time (NPT) increases with PAAS concentration, decreases with TMP. The change trend of permeate flux with time is affected by pH. The permeate fluxes rapidly decrease from the start, and then increase gradually to stable values at pH 5.0, pH 7.0 and pH 9.3. However, it decreases gradually with time till a state value at pH 3.0 (iso-electric point, IEP). The removal of small molecules is easy at pH greater than iso-electric point (IEP). The change of filtration potential with time indicates the similar trend to that of permeation concentration, but the former is more convenient for indication of NPT.

One step graft copolymerization of acrylic acid and sodium styrene sulfonate onto high-density polyethylene film by preirradiation method

High-density polyethylene (HDPE) films were irradiated by 60Co gamma ray with a dose of 100 kGy in air and then immersed in aqueous solution of acrylic acid (AA) and sodium styrene sulfonate (SSS) at different temperature. The effects of grafting conditions such as temperature, reaction time, Mohr’s salt concentration, and total concentration of monomer on grafting yield were studied. Both grafting yield of AA and SSS onto HDPE respectively increases with total concentration of monomers. The highest grafting yield was observed at 3 mol/L monomers where the grafted PE swelled to the largest extent in the monomers mixture. The grafting yield increases with reaction time and then levels off. At higher temperature, the grafting yield decreases with Mohr’s salt concentration, but increases at low temperature when Mohr’s salt concentration is 0.083%. Which can be interpreted that in the presence of Fe2+ diperoxides and hydroperoxides may decompose at low temperature to form radical which can initiate the grafting. The physical and chemical properties of grafting films were also investigated.

Study of radiation-induced grafting of acrylic acid-sodium styrene sulfonate onto poly (tetrafluoroethylene-co-hexafluoropropylene) film

Poly(tetrafluoroethylene-co-hexafluoropropylene) (FEP) films were immersed in aqueous solution of acrylic acid (AA) and sodium styrene sulfonate (SSS), then irradiated by Co γ-rays at 25℃. The effects of reaction 60 time,absorbed dose, dose-rate, inhibitor and monomer concentration on the grafting yield were studied. Grafting yields of both AA and SSS onto FEP, respectively, increase with irradiation dose, but some saturation will appear at high dose and monomer concentration. The grafting yield increases with reaction time and then levels off. The graft- ing of SSS onto FEP is more difficult than the grafting of AA. The analysis of grafted membranes using DSC and FT-IR have been done.

Removal of manganese from waste water by complexation-ultrafiltration using copolymer of maleic acid and acrylic acid

Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carboxylic group content of PMA-100 and the rate of complexation reaction were measured. Effects of the mass ratio of PMA-100 to Mn（II） （n）, pH, background electrolyte, etc on the rejection rate （R） and permeate flux （J） were investigated. The results show that carboxylic group content of PMA-100 is 9.5 mmol/g. The complexation of Mn（II） with PMA-100 is rapid and completed within 5 min at pH 6.0. Both R and J increase with pH increasing in the range of 2.5-7.0, and R increases with the increase of n at pH 6.0 while J is little affected. The background electrolyte leads to the decrease of R, and CaCl2 has much greater effect on R than NaCl at the same ionic strength.

Antimicrobial Expanded Polytetrafluoroethylene Film Prepared by 3-ray Radiation Induced Grafting of Poly（acrylic acid）

The simultaneous γ-ray-radiation-induced grafting polymerization of acrylic acid on ex- panded polytetrafluoroethylene （ePTFE） film was investigated. It was found that the degree of grafting （DG） of poly（acrylic acid） （PAA） can be controlled by the monomer concentration, absorbed dose, and dose rate under an optimal inhibitor concentration of [Fe2＋]=18 mmol/L. SEM observation showed that the macroporous structure in ePTFE films would be covered gradually with the increase of the DG of PAA. The prepared ePTFE-g-PAA film was im- mersed in a neutral silver nitrate solution to fabricate an ePTFE-g-PAA/Ag hybrid film after the addition of NaBH4 as a reduction agent of Ag＋ to Ag atom. SEM, XRD, and XPS results proved that Ag nanoparticles with a size of several tens of nanometers to 100 nanometers were in situ immobilized on ePTFE film. The loading capacity of Ag nanoparticles could be tuned by the DG of PAA, and determined by thermal gravimetric analysis. The quart- titative antibacterial activity of the obtained ePTFE-g-PAA/Ag hybrid films was measured using counting plate method. It can kill all the Escherichia coli in the suspension in 1 h. Moreover, this excellent antibacterial activity can last at least for 4 h. This work provides a facile and practical way to make ePTFE meet the demanding antimicrobial requirement in more and more practical application areas.

PHOTOINITIATED INVERSE EMULSION POLYMERIZATION OF SODIUM ACRYLATE

Photoinitiated inverse emulsion polymerization of sodium acrylate(AANa)in kerosene was carried out at room orlower temperature,using 2,2-dimethoxy-2-phenylacetophenone(DMPA)as the initiator.Kinetic investigations indicated thatthe polymerization could be completed in about 30 min and produce polymer with high molecular weight(10~6～10~7).It wasfound that monomer droplets are the main sites for the polymerization(nucleation).With the increase of DMPAconcentration,polymerization rate(R_p)reaches a maximum value while molecular weight of the produced polymer has anadverse result,but the dependence of R_p on incident light intensity is similar.Influences of other parameters such asmonomer concentration,emulsifier content and reaction temperature,etc.were also studied.At lower pH values of waterphase,R_p depends strongly on the pH due to the electrostatic interaction between the ionized radicals and the monomer.Athigher pH,R_p shows a slight dependence on pH.

Redox active polymer metal chelates for use in flexible symmetrical supercapacitors:Cobalt-containing poly(acrylic acid)polymer electrolytes

The novel polymer metal chelate electrolytes(polychelates)were prepared by incorporation of cobalt sulfate(Co)into poly(acrylic acid)(PAA)host matrix.Quasi-solid state supercapacitor devices were fabricated using polychelates,PAA-Co X(X:3,5,7,and 10)where X represents the doping fraction(w/w)of Co in PAA.All polymer metal electrolytes were showed excellent bending-stretching properties,thermal stability and electrochemical durability with an optimum ionic conductivity of 3.15×10^(-4) S cm^(-1).Hierarchically porous activated carbon and nano-sized conductive carbon were used to form carbon composite symmetrical device electrodes.The electric double-layer capacitor(EDLC)and redox reactions of Co-incorporated polychelates at the interfaces of porous activated carbon provided an optimum specific capacitance of 341.33 F g^(-1) with a device of PAA-Co7,which is at least 15 times enhancement compared to the device of pristine PAA.The PAA-Co7 device also provided energy density of 21.25 Wh kg^(-1) at a power density of 117.69 W kg^(-1).A prolonged cyclic stability of the device exhibited superior capacitive performance after 10,000 charge-discharge cycles and the maintained 90%of its initial performance.In addition,the supercapacitor with a dimension of 1.5 cm×3 cm containing PAA-Co7 successfully operated the red-blue-green(RGB)LED light.

PREPARATION OF POLY(ETHYLENEGLYCOL-co-ACRYLIC ACID) MICROSPHERES WITH DIVINYLBENZNE AS CROSSLINKER BY DISTILLATION-PRECIPITATION POLYMERIZATION

Monodisperse poly（poly（ethyleneglycol） methyl ether acrylate-co-acrylic acid） （poly（PEGMA-co-AA）） microspheres were prepared by distillation-precipitation polymerization with divinylbenzene （DVB） as crosslinker with 2,2＇- azobisisobutyronitrile （AIBN） as initiator in neat acetonitrile without stirring. Under various reaction conditions, four distinct morphologies including the sol, microemulsion, microgels and microspheres were formed during the distillation of the solvent from the reaction system. A 2D morphological map was established as a function of crosslinker concentration and the polar monomer AA concentration, in comonomer feed in the transition between the morphology domains. The effect of the covalent crosslinker DVB on the morphology of the polymer network was investigated in detail at AA fraction of 40 vol%. The ratios of acid to ethylene oxide units presenting in the comonomers dramatically affected the polymer-polymer interaction and hence the morphology of the resultant polymer network. The covalent crosslinking by DVB and the hydrogen bonding crosslinking between two acid units as well as between the acid and ethylene oxide unit played key roles in the formation of monodisperse polymer microspheres.

CONFORMATIONAL CHARACTERISTICS OF POLY(ACRYLIC ACID) AND POLY(METHACRYLIC ACID)

A full-relaxation optimization of molecule and the Dreiding force field are employed to obtain the geometry parameters and the conformational energy surfaces of meso or racemic dyad of poly(acrylic acid) (PAA) and poly(methacrylic acid) (PMAA). Three different carbonyl-bond orientations of side-groups resulted in the differences in depth of potential wells in their energetic contours for a meso or a racemic dyad. These discrepancies are interpreted as a result of various fine structures corresponding to grid search conformations as well as thereby different interactions. The analysis on the most stable conformations of PMAA confirmed that the ester groups are nearly perpendicular to the plane defined by the two adjacent skeletal bonds but may possibly change their relative orientations to meet the requirement of lower energy during the conformational state transition. For each polymer, two global energy maps of a meso and a racemic dyad were finally constructed from the superposition of energy data for the three kinds of side-group orientations by the Boltzmann factors. From an ensemble average, the proposed scheme with three rotational isomeric states (RIS) allowed us to access the experimentally unperturbed dimensions of PAA chain via the configurational statistical mechanics. Although the calculation was based on the short-range, local interactions, it was interested to note that the experimental characteristic ratios just fell within the range calculated for atactic chains.

Effect of Sodium Alginate Concentration on Membrane Strength and Permeating Property of Poly-l-arginine Group Microcapsule

A novel poly-/-arginine microcapsule was prepared due to its nutritional function and pharmacological efficacy. A high-voltage electrostatic droplet generator was used to make uniform microcapsules. The results show that the membrane strength and permeating property are both remarkably affected with the changes of sodium alginate concentration. With the sodium alginate concentration increasing, gel beads sizes increase from 233μm to 350μm, release ratio is also higher at the same time, but the membrane strength decreases.

Microstructure and Mechanical Properties of Poly (Vinyl Chloride) Modified by Silica Fume /Acrylic Core-Shell Impact Modifier Blends

This research explored replacing acrylic core-shell impact modifier （AIM） by silica fume to toughen PVC. 100%, 75%, 50% and 25% of AIM （8 phr） were substituted by silica fume in PVC respectively, and then processed by dry blending and twin-screw extrusion. Severe silica fume agglomeration was observed by scanning electron microscope （SEM） in the PVC matrix when 8 phr pure silica fume was used and processed by screw speed of 20 rpm. Its tensile strength was thereby reduced by 38% comparing to unmodified PVC. The silica fume was successfully dispersed while the screw speed was slowed down to 10 rpm to give a stronger screw torque and a longer melt residential time in the extruder. The tensile strength was ’recovered’ to a level comparable to unmodified PVC. Impact test were performed on all formulations extruded at 10 rpm screw speed and synergetic toughening effect was found with 50% substitution and it had the impact strength that was comparable to 8 phr pure AIM toughened PVC.

Poly (Acrylamide-co-Acrylic Acid) Hydrogel Induced by Glow-Discharge Electrolysis Plasma and Its Adsorption Properties for Cationic Dyes

In this paper, poly （acrylamide-co-acrylic acid） （P（AM-co-AA）） hydrogel was pre- pared in an aqueous solution by using glow-discharge electrolysis plasma （GDEP） induced copoly- merization of acrylamide （AM） and acrylic acid （AA）, in which N,N＇-methylenebisacrylamide （MBA） was used as a crosslinker. A mechanism for the synthesis of P（AM-co-AA） hydrogel was proposed. To optimize the synthesis condition, the following parameters were examined in detail： the discharge voltage, discharge time, the content of the crosslinker, and the mass ratio of AM to AA. The results showed that the optimum pH range for cationic dyes removal was found to be 5.0-10.0. The P（AM-co-AA） hydrogel exhibits a very high adsorption potential and the ex- perimental adsorption capacities for Crystal violet （CV） and Methylene blue （MB） were 2974.3 mg/g and 2303.6 mg/g, respectively. The adsorption process follows a pseudo-second-order kinetic model. In addition, the adsorption mechanism of P（AM-co-AA） hydrogel for cationic dyes was also discussed.

Molecular Imprinting Fibrous Membranes of Poly(acrylonitrile-co-acrylic acid) Prepared by Electrospinning

IntroductionOver the past few decades, molecular imprinting has been described as a technology for preparing ＂molecular doors＂ which can be matched to ＂template keys＂. It has been found to be a simple and effective approach to introduce specific recognition sites into synthetic polymers, namely, to create molecular imprinting polymers Remarkable features such as stability, ease of preparation and low cost, have made molecular imprinting polymers particularly attractive in chemical sensors, catalysis, drug delivery, and dedicated separations. Practical applications of molecular imprinting polymers require accessible sites, fast mass transfer, and quick binding. However, present techniques used to prepare molecular imprinting polymers most often result in materials exhibiting a high affinity and selectivity but a low capacity and poor site accessibility for the target molecules. It is also very difficult to remove the imprinted molecules located in these molecular imprinting polymers because the highly cross-linked structures do not allow the templates to move freely. To some extent, combining molecular imprinting technology with membrane separation and surface imprinting can overcome the shortcomings, such as mass transfer limitations and non-quantitative recovery of the template molecules seen for imprinted materials fabricated by conventional bulk methods. In that ease, it appears to us that molecular imprinting polymers with high surface area to volume ratios are particularly desirable for largescale applications. Eleetrospun nano and ultrafine fibrous membranes are the most suitable materials due to advantages such as： （1） large specific surfaces, providing relatively high imprinting sites per unit mass; （2） fine porous structures, resulting in the accessibility of imprinting sites and low diffusion resistance necessary for high efficiency; and （3） easy recoverability from practical operation or applicability for continuous usages. Therefore, in this work, we prepared a unique kind of imprinted material--molecularly imprinted fibrous membranes of poly （ acrylonitrile-co-acrylic acid） fabricated by means of an electrospinning process.

Aggregation of Sodium Dodecyl Sulfonate in Poly-ethylene Glycol Aqueous Solutions Studied by Two-dimensional Nuclear Overhauser Enhancement Spectroscopy

Two-dimensional nuclear overhauser enhancement (2D NOESY)measurements show that sodium dodecyl sulfonate SDSN molecules co-aggregate with poly-ethylene glycol PEG in their aqueous solution at a concentration range of SDSN between the so-called co-aggregation concentration (cac) and the. Normal critical micellar concentration (cmc). SDSN micelles are formed when the cmc of SDSN is reached with PEG uniformly distributed in the interior.

CD POLY/Acrylic/Viscose混纺弹性织物气流机染色

用阳离子染料对CD POLY／Acrylic／Viscose混纺弹性织物进行一浴法染色，在大货生产中容易出现色差、折痕和毛头等问题。实验通过分段式升温，控制40-70℃升温速率为1．0℃／min，70-90℃升温速率为0．3℃／min，90-105℃升温速率为0．5℃／min，105℃保温30min能有效控制色差问题；气流机染色选用合适的行机条件也是控制质量问题的关键。设定行机条件为45％的风机，80％N差，机速350m／min，行一圈时间2．75min。大生产证明织物的布面品质良好。

MODIFICATION OF POLYETHYLENE BY in situ FORMED SODIUM ACRYLATE

To improve the water tree resistance of PE, linear low-density polyethylene （LLDPE） was compounded with sodium acrylate （NaAA） for in situ polymerization, in which NaAA was fbrmed through the neutralization of acrylic acid （AA） with sodium hydroxide （NaOH） before adding dicumyl peroxide （DCP） to initiate the in situ graft polymerization and homo polymerization. A series of LLDPE/NaAA compounds were investigated for their water absorption ratio （WAR） measurement, water treeing, mechanical and dielectric properties. The results strongly suggest that NaAA can improve the water tree resistance of LLDPE. In addition, the LLDPE/NaAA compounds possess satisfactory mechanical properties and dielectric properties. Characterization of LLDPE/NaAA compounds by using Fourier transform infrared spectrometry （FTIR） suggests that the neutralization and polymerization reaction could be achieved effectively. Using adequate DCP content is the key factor for controlling the polymerization of NaAA with precise conversion ratio.

Synthesis and Properties of IPN Hydrogels Based on Konjac Glucomannan and Poly(acrylic acid)

Novel interpenetrating polymer network （IPN） hydrogels based on konjac glucomannan （KGM） and poly（acrylic acid） （PAA） were prepared by polymerization and cross-linking of acrylic acid （AA） in the pre-fabricated KGM gel. The IPN gel was analyzed by FF-IR. The studies on the equilibrium swelling ratio of IPN hydrogels revealed their sensitive response to environmental pH value. The results of in vitro degradation showed that the IPN hydrogels retain the enzymatic degradation character of KGM.

STUDY ON ACRYLAMIDE-SODIUM ACRYLATE COPOLYMER GELS

Acrylamide-sodium acrylate copolymer hydrogels have been obtained by radiation techniques. Two different methods have been used to introduce—COONa groups into polymer chains of the gels: (1) by partial hydrolysis of acrylamide homopolymer gel; (2) by direct copolymerization and crosslinking of acrylamide and sodium acrylate in aqueous solutions. It was found that the gels obtained in different ways had different properties, the swelling character of the gels obtained by partial hydrolysis were more sensitive to pH of swelling aqueous media, in order to explain these differences, ^(13)C-NMR techniques were used to investigate the sequence distribution of monomer units of both gels.

POLYMERIZATION OF ETHYLENE METHYL PHOSPHATE IN THE PRESENCE OF SODIUM POLY(ETHYLENE GLYCOL)ATE

Poly(ethylene methyl phosphate)-poly(ethylene glycol)-poly(ethylene methyl phosphate) triblock copolymers carrying hydroxyl group at both chain ends were synthesized with sodium poly(ethylene glycol)ate as initiator. The effects of the factors such as solvent, amount of the initiator and reaction time were investigated. The copolymers were characterized by IR, H-1-NMR, H-1{P-31}-NMR, C-13-NMR, P-31{H-1}-NMR, and DSC. High molecular weight of the copolymer and high yield of the polymerization were achieved within 3 min at 25 degrees C. The polymerization process was studied by P-31{H-1}-NMR and transesterification was found during longer polymerization time.