Reaction mode between Si and Fe and evaluation of optimal species in poly-silicic-ferric coagulant

A kind of Fe-polysilicate polymer, poly-silicic-ferric （PSF） coagulant was prepared by co-polymerization （hydroxylation of mixture of Fe^3＋ and fresh polysilicic acid （PS））, in which PSF0.5, PSF1 or PSF3 denotes Si/Fe molar ratio of 0.5, 1 or 3, respectively. The effects of Si/Fe ratio and reaction time （co-polymerization time or aging time） on the reaction mode between Si and Fe were studies, and the optimal species of PSF was evaluated by pH change during the preparation of PSF and coagulation tests. The results showed that the characteristics of PSF are largely affected by both reaction time and Si/Fe ratio. PSF is found to be a essential complex of Si, Fe, and many other ions. The reaction mode between Si and Fe differs with various Si/Fe ratios. The pH of PSF0.5, PSF1 or PSF3 tended to be stable when reaction time is 10, 25 or 55 rain, respectively, which is almost consistent with the time reaching the relative stable morphology that is just the optimal species of higher coagulation efficiency. The optimal reaction time reaching optimal species can be evaluated by measuring the pH change during the polymerization process.

Efficient and selective upcycling of waste polylactic acid into acetate using nickel selenide

The conversion of waste polylactic acid(PLA)plastics into high-value-added chemicals through electrochemical methods is a promising and sustainable approach.However,developing efficient and highly selective catalysts for lactic acid oxidation reaction(LAOR)and understanding the reaction process are challenging.Here,we report the electrooxidation of waste PLA to acetate at a high current density of 100 mA cm-2 with high Faraday efficiency(~95%)and excellent stability(>100 h)over a nickel selenide nanosheet catalyst.In addition,a total Faraday efficiency of up to 190%was achieved for carboxylic acids,including acetic acid and formic acid,by coupling with the cathodic CO_(2) reduction reaction.In situ experimental results and theoretical simulations revealed that the catalytic activity center of LAOR was dynamically formed NiOOH species,and the surface-adsorbed SeO_(x) species accelerated the formation of Ni~(3+)species,thus promoting catalytic activity.The mechanism of lactic acid electrooxidation was further elucidated.Lactic acid was dehydrogenated to produce pyruvate first and then formed CH_3CO due to preferential C-C bond cleavage,resulting in the presence of acetate.This work demonstrated a sustainable method for recycling waste PLA and CO_(2) into high-value-added products.

Edaravone-loaded poly(amino acid) nanogel inhibits ferroptosis for neuroprotection in cerebral ischemia injury

Neurological injury caused by ischemic stroke is a major cause of permanent disability and death. The currently available neuroprotective drugs fail to achieve desired therapeutic efficacy mainly due to short circulation half-life and poor blood−brain barrier (BBB) permeability. For that, an edaravone-loaded pH/glutathione (pH/GSH) dual-responsive poly(amino acid) nanogel (NG/EDA) was developed to improve the neuroprotection of EDA. The nanogel was triggered by acidic and EDA-induced high-level GSH microenvironments, which enabled the selective and sustained release of EDA at the site of ischemic injury. NG/EDA exhibited a uniform sub-spherical morphology with a mean hydrodynamic diameter of 112.3 ± 8.2 nm. NG/EDA efficiently accumulated at the cerebral ischemic injury site of permanent middle cerebral artery occlusion (pMCAO) mice, showing an efficient BBB crossing feature. Notably, NG/EDA with 50 µM EDA significantly increased neuron survival (29.3%) following oxygen and glucose deprivation by inhibiting ferroptosis. In addition, administering NG/EDA for 7 d significantly reduced infarct volume to 22.2% ± 7.2% and decreased neurobehavioral scores from 9.0 ± 0.6 to 2.0 ± 0.8. Such a pH/GSH dual-responsive nanoplatform might provide a unique and promising modality for neuroprotection in ischemic stroke and other central nervous system diseases.

Synergism of Zinc Oxide/Organoclay-Loaded Poly(lactic acid) Hybrid Nanocomposite Plasticized by Triacetin for Sustainable Active Food Packaging

The synergistic effect of organoclay(OC)and zinc oxide(ZnO)nanoparticles on the crucial properties of poly(lactic acid)(PLA)nanocompositefilms was systematically investigated herein.After their incorporation into PLA via the solvent casting technique,the water vapor barrier property of the PLA/OC/ZnOfilm improved by a maximum of 86%compared to the neat PLAfilm without the deterioration of Young’s modulus or the tensile strength.Moreover,thefilm’s self-antibacterial activity against foodborne pathogens,including gram-negative(Escherichia coli,E.coli)and gram-positive(Staphylococcus aureus,S.aureus)bacteria,was enhanced by a max-imum of approximately 98–99%compared to the neat PLAfilm.Furthermore,SEM images revealed the homo-geneous dispersion of both nano-fillers in the PLA matrix.However,the thermal stability of thefilm decreased slightly after the addition of the OC and ZnO.Thefilm exhibited notable light barrier properties in the UV-Vis range.Moreover,the incorporation of a suitable biodegradable plasticizer significantly decreased the Tg and notably enhanced theflexibility of the nanocompositefilm by increasing the elongation at break approxi-mately 1.5-fold compared to that of the neat PLAfilm.This contributes to its feasibility as an active food packa-ging material.

Technology of dehydration and transformation of silicic acid

The technology that silicic acid was pressurized under high temperature in order to dehydrate and transform was investigated in the paper. The effects, such as the ratio of liquid to solid, pressure, temperature, and reaction time on the dehydration rate and volume shrinkage rate, were researched. The experimental results show that the dehy- dration rate of silicic acid is up to 41.20 %, accompanying with the volume shrinkage rate of 40.37 % after silicic acid is pressurized under high temperature in the high-pressure kettle. The results of silicic acid tested by SEM indicate that the metasilicate acid molecules and water molecules are closely arranged, and there are almost no gaps before pressure reaction. There are many gaps accompanying with formatting lamellar structure after pressure reaction. The experimental results indicate the effect that silicic acid is dehydrated and transformation is obvious under high temperature and pressure.

Double Acid-Base Extraction of Silicic Acid from Quartz Sand

Silica is becoming more attractive as plant nutrient for non-graminae crops particularly in relation with drought-stress tolerant. Many efforts have been conducted to obtain an efficient technique to produce silica fertilizer worldwide, but the results are varying considerably due to various factors including raw material and extraction technique. This study was carried out to develop an efficient extraction technique for ortho-silicic acid (OSA-H4SiO4) from a Bangka-Belitung quartz sand by employing acid-base dissolution method. A 325-mesh size quartz sand was boiled in HCl solution at various concentrations. The optimum concentration was then used in the following experiment at several different volumes of solution. The sand obtained from optimum concentration and volume of HCl solution was then reacted with different amounts of NaOH (s), and heated until a wet mixture was obtained. As a reference the best extraction conditions were applied to a natural zeolite sample. All OSA analyses were done in triplicates with spectrophotometric method. Supporting evidences were collected from x-ray diffraction and scanning-electron-microscopy analyses of the treated samples. The yield of quartz sand-originated OSA was 183 g·kg-1 and significantly increased linearly with increasing weight of NaOH (R2 = 0.99**), whereas that from zeolite was only 104.2 g·kg-1 at 80 g NaOH. XRD and SEM data confirmed the evidences that the acid-base extraction disrupted the quartz mineral structure and as a consequence releasing more water soluble OSA.

Synthesis and Characterization of Modified Epoxy Resins by Silicic Acid Tetraethyl Ester and Nano-SiO_2

A kind of modified epoxy resins was obtained by condensation of epoxy resin with silicic acid tetraethyl ester（TEOS） and nano-SiO2. The reactions were performed with hydrochloric acid as a catalyst at 63 ℃. The structure, thermal stability and morphological characteristics of the modified epoxy resins were studied through infrared spectra（FT-IR） analysis, thermogravimetric（TG） analysis and scanning electron microscopy respectively. It has been found from the IR and TG study that modified epoxy resins have greater thermal stability than epoxy resins, and its thermal stability has been improved by the formation of inter-crosslinked network structure. The modified epoxy resins exhibit heterogeneous morphology and heterogeneity increases with more TEOS feeding, which in turn confirms the formation of inter-crosslinked network structure in modified epoxy resins.

Cleaning the Ion Exchange Resin Sorption of Uranium from Silicic Acid Solution ＂Ayanat＂

The authors discovered a new way to clean the ion exchange resin sorption of uranium from silicic acid used solution ＂Ayanat＂. The method reduces the costs of regeneration of ion exchange resin and its reuse in the sorption of uranium.

A STUDY OF SILICA-SUPPORTED CROSS-LINKED POLY (MALEIC ACID-CO-STYRENE)-PLATINUM COMPLEX IN THE HYDROGENATION OF p-CRESOL

A silica-supported cross-linked poly(maleic acid -co- styrene)-platinum complex (PMS-Pt) has been prepared and found to be active in the hydrogenation of p-cresol under mild conditions (303-323K, 1.01 x 10(5)Pa). In this hydrogenation system water serves as a solvent and p-cresol can be converted to 4-methylcyclohexanol quantitatively via 4-methylcyclohexanone as intermediate.

Effects of Temperature on the Deposition Rate of Supersaturated Silicic Acid on Ca-type Bentonite Tsuyoshi Sasagawa, Taiji Chida and Yuichi Niibori

Na-type bentonite is commonly used as a tunnel backfilling material to prevent groundwater and radionuclide migration during the construction of a geological disposal system for high-level radioactive waste in Japan. However, host rock fractures with strong water flow can develop groundwater paths in the backfilling material. Especially, the alteration to Ca-type bentonite causes degradation of the barrier performance and accelerates the development of groundwater paths. Additionally, using cementitious materials gradually changes pH between 13 and 8. High alkaline groundwater results in high solubility of silicic acid; therefore, silicic acid is eluted from the host rock. Downstream, in the low alkaline area, the groundwater becomes supersaturated in silicic acid. This acid is deposited on Ca-type bentonite, thus leading to the clogging of the groundwater paths. In the present study, we investigate the silicic acid deposition rate on Ca-type bentonite under 288-323 K for depths greater or equal to 500 m. The results indicate that temperature does not affect the silicic acid deposition rate up to 323 K. However, in this temperature range, the deposition of silicic acid on Ca-type bentonite in backfilled tunnels results in clogging of the flow paths.

Removal of manganese from waste water by complexation-ultrafiltration using copolymer of maleic acid and acrylic acid

Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carboxylic group content of PMA-100 and the rate of complexation reaction were measured. Effects of the mass ratio of PMA-100 to Mn（II） （n）, pH, background electrolyte, etc on the rejection rate （R） and permeate flux （J） were investigated. The results show that carboxylic group content of PMA-100 is 9.5 mmol/g. The complexation of Mn（II） with PMA-100 is rapid and completed within 5 min at pH 6.0. Both R and J increase with pH increasing in the range of 2.5-7.0, and R increases with the increase of n at pH 6.0 while J is little affected. The background electrolyte leads to the decrease of R, and CaCl2 has much greater effect on R than NaCl at the same ionic strength.

Antimicrobial Expanded Polytetrafluoroethylene Film Prepared by 3-ray Radiation Induced Grafting of Poly（acrylic acid）

The simultaneous γ-ray-radiation-induced grafting polymerization of acrylic acid on ex- panded polytetrafluoroethylene （ePTFE） film was investigated. It was found that the degree of grafting （DG） of poly（acrylic acid） （PAA） can be controlled by the monomer concentration, absorbed dose, and dose rate under an optimal inhibitor concentration of [Fe2＋]=18 mmol/L. SEM observation showed that the macroporous structure in ePTFE films would be covered gradually with the increase of the DG of PAA. The prepared ePTFE-g-PAA film was im- mersed in a neutral silver nitrate solution to fabricate an ePTFE-g-PAA/Ag hybrid film after the addition of NaBH4 as a reduction agent of Ag＋ to Ag atom. SEM, XRD, and XPS results proved that Ag nanoparticles with a size of several tens of nanometers to 100 nanometers were in situ immobilized on ePTFE film. The loading capacity of Ag nanoparticles could be tuned by the DG of PAA, and determined by thermal gravimetric analysis. The quart- titative antibacterial activity of the obtained ePTFE-g-PAA/Ag hybrid films was measured using counting plate method. It can kill all the Escherichia coli in the suspension in 1 h. Moreover, this excellent antibacterial activity can last at least for 4 h. This work provides a facile and practical way to make ePTFE meet the demanding antimicrobial requirement in more and more practical application areas.

Synthesis of the Biomimetic Polymer: Aliphatic Diamine and RGDS Modified Poly(d,l-lactic acid)

A novel poly（d, /-lactic acid） （PDLLA） based biomimetic polymer was synthesized by grafting maleic anhydride, butanediamine and arg-gly-asp-ser （RGDS） peptides onto the backbone of PDLLA, aiming to overcome the acidity and auto-accelerating degradation of PDLLA during degradation and to improve its biospecificity and biocompatibility. The synthetic copolymer was characterized by FTIR, ^13C NMR and amino acid analyzer （AAA）.

CLAY CATALYZED SYNTHESIS OF BIO-DEGRADABLE POLY(GLYCOLIC ACID)

Glycolic acid was polymerized under vacuum in the presence and absence of nano sized clay.The added clay catalyzed the condensation polymerization which can be confirmed by recording FTIR spectroscopy and intrinsic viscosity (Ⅳ)values.The relative intensity of C=O/CH is increased while increasing the amount of clay.DSC showed the appearance of multiple endotherms of poly(glycolic acid).TGA showed the percentage weight residue remain above 750℃for polymer-nano composite system was 21% and hence proved the fl...

Preparation and properties of short natural fiber reinforced poly(lactic acid) composites

The natural fiber/poly(lactic acid) (PLA) composites were prepared with ramie and jute short fiber as reinforcement and PLA as matrix. The mechanical and thermal properties of the composites were investigated. The results show that the properties of the composites are better than those of plain PLA. When the content of the fiber is 30%, the composites can get the best mechanical properties. The dynamic mechanical analysis results show that the storage moduli of the PLA/ramie and PLA/jute composites increase with respect to the plain PLA. The Vicat softening temperature of the composites is greatly higher than that of PLA. The results of thermogravimetric analysis show that adding fiber to the PLA matrix can improve the degradation temperature of PLA.

SYNTHESIS OF MESOPOROUS POLY(STYRENE-co-MALEIC ANHYDRIDE)/SILICA HYBRID MATERIALS VIA A NONSURFACTANT-TEMPLATED SOL-GEL PROCESS

Mesoporous poly(styrene-co-maleic anhydride)/silica hybrid materials have been prepared. The synthesis was achieved by the HCl-catalyzed sol-gel reactions of tetraethyl orthosilicate (TEOS) and styrene-maleic anhydride copolymer in the presence of 3-aminopropyl triethoxysilane (APTES) as a coupling agent and citric acid as a nonsurfactant template or pore-forming agent, followed by ethanol extraction. Characterization results from nitrogen sorption isotherms and powder X-ray diffraction indicate that polymer-modified mesoporous materials with large specific surface areas (e.g. 900 m(2)/g) and pore volumes (e.g. 0.6 cm(3)/g) could be prepared. As the citric acid concentration is increased, the specific surface areas, pore volumes and pore diameters of the hybrid materials increase.

Pressure leaching of zinc silicate ore in sulfuric acid medium

Zinc silicate ore was characterized mineralogically and the results showed that zinc exists mainly as hemimorphite and smithsonite in the sample.Sulfuric acid pressure leaching of zinc silicate ore was carried out to assess the effect of particle size,sulfuric acid concentration,pressure,reaction time and temperature on the extraction of zinc and the dissolution of silica.Under the optimum conditions employed,up to 99.25% of zinc extraction and 0.20% silica dissolution are obtained.The main minerals in leaching residue are quartz and small amounts of undissolved oxide minerals of iron,lead and aluminum are associated with quartz.

A Hybrid Membrane of Poly(vinyl alcohol) and Phosphotungstic Acid for Fuel Cells

Proton conducting membranes composed of phosphotungstic acid (PWA) and poly(vinyl alcohol) (PVA)were prepared. Conductivity and Fourier transform infrared spectrometer(FTIR) measurements show that most ofthe acid embedded are stable in the PVA matrix when the membrane is immerged in water or methanol solution atroom temperature. Conductivity of the composite membranes scatters around 10-3 S.cm-1 at room temperature.The methanol crossover through the membranes is about an order of magnitude lower than that through Nafion117 membrane.

Synthesis and Characterization of a Novel Biomaterial: Maleic Anhydride-modified Poly(dl-lactic acid)

A novel modified poly(dl-lactic acid) (PDLLA) was obtained by covalently grafting of maleic anhydride onto the backbone of PDLLA, attempting to improve PDLLA’s hydrophilicity and cell affinity and to provide reactive groups for further chemical modification. FTIR, 13C NMR and DSC were used to characterize the maleic anhydride-modified PDLLA.