A novel method was developed to establish a realistic three dimensional(3D) network model representing pore space in low permeability sandstone.Digital core of rock sample was established by the combination of micro-C...A novel method was developed to establish a realistic three dimensional(3D) network model representing pore space in low permeability sandstone.Digital core of rock sample was established by the combination of micro-CT scanning and image processing,then 3D pore-throat network model was extracted from the digital core through analyzing pore space topology,calculating pore-throat parameters and simplifying the shapes of pores and throats.The good agreements between predicted and measured porosity and absolute permeability verified the validity of this new network model.Gas-water flow mechanism was studied by using pore-scale simulations,and the influence of pore structure parameters,including coordination number,aspect ratio and shape factor,on gas-water flow,was investigated.The present simulation results show that with the increment of coordination number,gas flow ability in network improves and the effect of invading water on blocking gas flow weakens.The smaller the aspect ratio is,the stronger the anisotropy of the network is,resulting in the increase of seepage resistance.It is found that the shape factor mainly affects the end points in relative permeability curves,and for a highly irregular pore or throat with a small shape factor,the irreducible water saturation(Swi) and residual gas saturation(Sgr) are relatively high.展开更多
Subsurface water flow velocity influences the hydrodynamic characteristics of soil seepage and the interaction between subsurface water flow and surface runoff during soil erosion and sediment transport.A visualized m...Subsurface water flow velocity influences the hydrodynamic characteristics of soil seepage and the interaction between subsurface water flow and surface runoff during soil erosion and sediment transport.A visualized method and equipment was adopted in this study to observe the subsurface water flow.Quartz sand was used as the test material of subsurface water flow and fluorescent dye was used as the indicator for tracing subsurface water flow.Water was supplied at the same flow discharge to the three parts at the bottom of the test flume,and the subsurface water flow were determined with four slope gradients(4°,8°,10°,and 12°).The results showed that the seepage velocity gradually increased with increasing slope gradient.The pore water velocity at different depths of sand layer profile increased with increasing slope gradient,whereas the thickness of the flow front gradually decreased.For the same slope gradient,the pore water velocity in the lower layer was the largest,whereas the thickness of the flow front was the smallest.Comparative analysis of the relationship between seepage velocity and pore water velocity at different depths of sand layer profile showed that the maximum relative difference between the measured pore water velocity and the computational pore water velocity at different depths of sand profile in the experiment was 4.38%.Thus,the test method for measuring the subsurface water flow velocity of sand layer profile adopted in this study was effective and feasible.The development of this experiment and the exploration of research methods would lay a good test foundation for future studies on the variation law of subsurface water flow velocity and the determination of flow velocity in purple soils,thus contributing to the improvement of the hydrodynamic mechanism of purple soils.展开更多
Pore water pressure and water content are important indicators to both deposition and consolidation of debris flows, enabling a direct assessment of consolidation degree. This article gained a more comprehensive under...Pore water pressure and water content are important indicators to both deposition and consolidation of debris flows, enabling a direct assessment of consolidation degree. This article gained a more comprehensive understanding about the entire consolidation process and focused on exploring pore water pressure and volumetric water content variations of the deposit body during natural consolidation under different conditions taking the viscous debris flow mass as a study subject and by flume experiments. The results indicate that, as the color of the debris changed from initial dark green to grayish-white color, the initial deposit thickness declined by 3% and 2.8% over a permeable and impermeable sand bed, respectively. A positive correlation was observed between pore water pressure and depth in the deposit for both scenarios, with deeper depths being related to greater pore water pressure. For the permeable environment, the average dissipation rate of pore water pressure measured at depths of 0.10 m and 0.05 m were 0.0172 Pa/d and 0.0144 Pa/d, respectively, showing a positivechanging trend with increasing depth. Under impermeable conditions, the average dissipation rates at different depths were similar, while the volumetric water content in the deposit had a positive correlation with depth. The reduction of water content in the deposit accelerated with depth under impermeable sand bed boundary conditions, but was not considerably correlated with depth under permeable sand bed boundary conditions. However, the amount of discharged water from the deposit was greater and consolidation occurred faster in permeable conditions. This indicates that the permeability of the boundary sand bed has a significant impact on the progress of consolidation. This research demonstrates that pore water and pressure dissipations are present during the entire viscous debris consolidation process. Contrasting with dilute flows, pore pressure dissipation in viscous flows cannot be completed in a matter of minutes or even hours, requiring longer completion time — 3 to 5 days and even more. Additionally, the dissipation of the pore water pressure lagged the reduction of the water content. During the experiment, the dissipation rate fluctuated substantially, indicating a close relationship betweenthe dissipation process and the physical properties of broadly graded soils.展开更多
The production of runoff in the source area of a debris flow is the consequence of a reduction in soil strength. Gravel soil is widely distributed in the source region, and the influence of its clay content on soil st...The production of runoff in the source area of a debris flow is the consequence of a reduction in soil strength. Gravel soil is widely distributed in the source region, and the influence of its clay content on soil strength is one of the important questions regarding the formation mechanism of debris flows. In this paper, the clay content in gravel soil is divided into groups of low clay content(1%, 2, 5%), moderate clay content(3.75%, 5.00%, 6.25%, 7.5%) and high clay content(10.0%, 12.5%, 15%). Tests of the unconsolidated undrained shear strength and consolidated drained shear strength were performed. The unconsolidated undrained shearing(UU) experiment simulates the rapid shear failure of loose gravel soil under the conditions of brief heavy rainfall. The consolidated drained shearing(CD) experiment simulates creep failure of consolidated sediment during extended rainfall. The pore water pressure first increased and then decreased as the clay content increased, and the increase in pore pressure was relatively high in the gravel soil sample when the clay content is in the range of 3.25-7.50%, and stress in the gravel soil is relatively low for a moderate clay content. Gravelly soils with a moderate clay content are moreprone to debris-flow initiation. This paper presents a mathematical formula for the maximum shear stress and clay content of gravel soil under two conditions. The key processes whereby the soil fails and triggers a debris flow—volume contraction of soil, expansion of clay soil, and rise of pore pressure―cause reductions in the soil friction force and enhancement of the water content in the clay particles, and subsurface erosion of soil reduces the soil viscosity, which eventually reduces the soil strength so that the soil loses its stability, liquefies and generates a debris flow.展开更多
基金Project(2013CB228005) supported by the National Program on Key Fundamental Research Project of ChinaProject(14ZB0047) supported by the Department of Education of Sichuan Province,China
文摘A novel method was developed to establish a realistic three dimensional(3D) network model representing pore space in low permeability sandstone.Digital core of rock sample was established by the combination of micro-CT scanning and image processing,then 3D pore-throat network model was extracted from the digital core through analyzing pore space topology,calculating pore-throat parameters and simplifying the shapes of pores and throats.The good agreements between predicted and measured porosity and absolute permeability verified the validity of this new network model.Gas-water flow mechanism was studied by using pore-scale simulations,and the influence of pore structure parameters,including coordination number,aspect ratio and shape factor,on gas-water flow,was investigated.The present simulation results show that with the increment of coordination number,gas flow ability in network improves and the effect of invading water on blocking gas flow weakens.The smaller the aspect ratio is,the stronger the anisotropy of the network is,resulting in the increase of seepage resistance.It is found that the shape factor mainly affects the end points in relative permeability curves,and for a highly irregular pore or throat with a small shape factor,the irreducible water saturation(Swi) and residual gas saturation(Sgr) are relatively high.
基金This work was supported by the Fundamental Research Funds for the National Natural Science Foundation of China(No.41571265,41971244)the Key Research and Development Project of Social Livelihood in Chongqing(cstc2018jscxmszdX0061)the Foundation of Graduate Research and Innovation in Chongqing under project CYB18089.
文摘Subsurface water flow velocity influences the hydrodynamic characteristics of soil seepage and the interaction between subsurface water flow and surface runoff during soil erosion and sediment transport.A visualized method and equipment was adopted in this study to observe the subsurface water flow.Quartz sand was used as the test material of subsurface water flow and fluorescent dye was used as the indicator for tracing subsurface water flow.Water was supplied at the same flow discharge to the three parts at the bottom of the test flume,and the subsurface water flow were determined with four slope gradients(4°,8°,10°,and 12°).The results showed that the seepage velocity gradually increased with increasing slope gradient.The pore water velocity at different depths of sand layer profile increased with increasing slope gradient,whereas the thickness of the flow front gradually decreased.For the same slope gradient,the pore water velocity in the lower layer was the largest,whereas the thickness of the flow front was the smallest.Comparative analysis of the relationship between seepage velocity and pore water velocity at different depths of sand layer profile showed that the maximum relative difference between the measured pore water velocity and the computational pore water velocity at different depths of sand profile in the experiment was 4.38%.Thus,the test method for measuring the subsurface water flow velocity of sand layer profile adopted in this study was effective and feasible.The development of this experiment and the exploration of research methods would lay a good test foundation for future studies on the variation law of subsurface water flow velocity and the determination of flow velocity in purple soils,thus contributing to the improvement of the hydrodynamic mechanism of purple soils.
基金funded by the Topic of National Sci-tech Support Plan(2014BAL05B01)Chinese Academy of Sciences STS-Network Projects(KFJ-EW-STS-094)Key Laboratory of Mountain Hazards and Earth Surface Processes under Major Research Projects(Y3K2040040)of Chinese Academy of Sciences
文摘Pore water pressure and water content are important indicators to both deposition and consolidation of debris flows, enabling a direct assessment of consolidation degree. This article gained a more comprehensive understanding about the entire consolidation process and focused on exploring pore water pressure and volumetric water content variations of the deposit body during natural consolidation under different conditions taking the viscous debris flow mass as a study subject and by flume experiments. The results indicate that, as the color of the debris changed from initial dark green to grayish-white color, the initial deposit thickness declined by 3% and 2.8% over a permeable and impermeable sand bed, respectively. A positive correlation was observed between pore water pressure and depth in the deposit for both scenarios, with deeper depths being related to greater pore water pressure. For the permeable environment, the average dissipation rate of pore water pressure measured at depths of 0.10 m and 0.05 m were 0.0172 Pa/d and 0.0144 Pa/d, respectively, showing a positivechanging trend with increasing depth. Under impermeable conditions, the average dissipation rates at different depths were similar, while the volumetric water content in the deposit had a positive correlation with depth. The reduction of water content in the deposit accelerated with depth under impermeable sand bed boundary conditions, but was not considerably correlated with depth under permeable sand bed boundary conditions. However, the amount of discharged water from the deposit was greater and consolidation occurred faster in permeable conditions. This indicates that the permeability of the boundary sand bed has a significant impact on the progress of consolidation. This research demonstrates that pore water and pressure dissipations are present during the entire viscous debris consolidation process. Contrasting with dilute flows, pore pressure dissipation in viscous flows cannot be completed in a matter of minutes or even hours, requiring longer completion time — 3 to 5 days and even more. Additionally, the dissipation of the pore water pressure lagged the reduction of the water content. During the experiment, the dissipation rate fluctuated substantially, indicating a close relationship betweenthe dissipation process and the physical properties of broadly graded soils.
基金supported by the National Natural Science Foundation of China(Grant Nos.41501012 and 41502337)the China Geological Survey(Grant No.121201010000150003)
文摘The production of runoff in the source area of a debris flow is the consequence of a reduction in soil strength. Gravel soil is widely distributed in the source region, and the influence of its clay content on soil strength is one of the important questions regarding the formation mechanism of debris flows. In this paper, the clay content in gravel soil is divided into groups of low clay content(1%, 2, 5%), moderate clay content(3.75%, 5.00%, 6.25%, 7.5%) and high clay content(10.0%, 12.5%, 15%). Tests of the unconsolidated undrained shear strength and consolidated drained shear strength were performed. The unconsolidated undrained shearing(UU) experiment simulates the rapid shear failure of loose gravel soil under the conditions of brief heavy rainfall. The consolidated drained shearing(CD) experiment simulates creep failure of consolidated sediment during extended rainfall. The pore water pressure first increased and then decreased as the clay content increased, and the increase in pore pressure was relatively high in the gravel soil sample when the clay content is in the range of 3.25-7.50%, and stress in the gravel soil is relatively low for a moderate clay content. Gravelly soils with a moderate clay content are moreprone to debris-flow initiation. This paper presents a mathematical formula for the maximum shear stress and clay content of gravel soil under two conditions. The key processes whereby the soil fails and triggers a debris flow—volume contraction of soil, expansion of clay soil, and rise of pore pressure―cause reductions in the soil friction force and enhancement of the water content in the clay particles, and subsurface erosion of soil reduces the soil viscosity, which eventually reduces the soil strength so that the soil loses its stability, liquefies and generates a debris flow.