In-situ stress is a common stress in the exploration and development of oil reservoirs. Therefore, it is of great significance to study the propagation characteristics of borehole acoustic waves in fluid-saturated por...In-situ stress is a common stress in the exploration and development of oil reservoirs. Therefore, it is of great significance to study the propagation characteristics of borehole acoustic waves in fluid-saturated porous media under stress.Based on the acoustoelastic theory of fluid-saturated porous media, the field equation of fluid-saturated porous media under the conditions of confining pressure and pore pressure and the acoustic field formula of multipole source excitation in open hole are given. The influences of pore pressure and confining pressure on guided waves of multipole borehole acoustic field in fluid-saturated porous media are investigated. The numerical results show that the phase velocity and excitation intensity of guided wave increase significantly under the confining pressure. For a given confining pressure, the phase velocity of the guided wave decreases with pore pressure increasing. The excitation intensity of guided wave increases at low frequency and then decreases at high frequency with pore pressure increasing, except for that of Stoneley wave which decreases in the whole frequency range. These results will help us get an insight into the influences of confining pressure and pore pressure on the acoustic field of multipole source in borehole around fluid-saturated porous media.展开更多
The measurement of nuclear magnetic resonance(NMR)porosity is affected by temperature.Without considering the impact of NMR logging tools,this phenomenon is mainly caused by variations in magnetization intensity of th...The measurement of nuclear magnetic resonance(NMR)porosity is affected by temperature.Without considering the impact of NMR logging tools,this phenomenon is mainly caused by variations in magnetization intensity of the measured system due to temperature fluctuations and difference between the temperature of the porous medium and calibration sample.In this study,the effect of temperature was explained based on the thermodynamic theory,and the rules of NMR porosity responses to temperature changes were identified through core physics experiments.In addition,a method for correcting the influence of temperature on NMR porosity measurement was proposed,and the possible factors that may affect its application were also discussed.展开更多
Based on the tortuous capillary network model,the relationship between anisotropic permeability and rock normal strain,namely the anisotropic dynamic permeability model(ADPM),was derived and established.The model was ...Based on the tortuous capillary network model,the relationship between anisotropic permeability and rock normal strain,namely the anisotropic dynamic permeability model(ADPM),was derived and established.The model was verified using pore-scale flow simulation.The uniaxial strain process was calculated and the main factors affecting permeability changes in different directions in the deformation process were analyzed.In the process of uniaxial strain during the exploitation of layered oil and gas reservoirs,the effect of effective surface porosity on the permeability in all directions is consistent.With the decrease of effective surface porosity,the sensitivity of permeability to strain increases.The sensitivity of the permeability perpendicular to the direction of compression to the strain decreases with the increase of the tortuosity,while the sensitivity of the permeability in the direction of compression to the strain increases with the increase of the tortuosity.For layered reservoirs with the same initial tortuosity in all directions,the tortuosity plays a decisive role in the relative relationship between the variations of permeability in all directions during pressure drop.When the tortuosity is less than 1.6,the decrease rate of horizontal permeability is higher than that of vertical permeability,while the opposite is true when the tortuosity is greater than 1.6.This phenomenon cannot be represented by traditional dynamic permeability model.After the verification by experimental data of pore-scale simulation,the new model has high fitting accuracy and can effectively characterize the effects of deformation in different directions on the permeability in all directions.展开更多
Recent advances in deep neural networks have shed new light on physics,engineering,and scientific computing.Reconciling the data-centered viewpoint with physical simulation is one of the research hotspots.The physicsi...Recent advances in deep neural networks have shed new light on physics,engineering,and scientific computing.Reconciling the data-centered viewpoint with physical simulation is one of the research hotspots.The physicsinformedneural network(PINN)is currently the most general framework,which is more popular due to theconvenience of constructing NNs and excellent generalization ability.The automatic differentiation(AD)-basedPINN model is suitable for the homogeneous scientific problem;however,it is unclear how AD can enforce fluxcontinuity across boundaries between cells of different properties where spatial heterogeneity is represented bygrid cells with different physical properties.In this work,we propose a criss-cross physics-informed convolutionalneural network(CC-PINN)learning architecture,aiming to learn the solution of parametric PDEs with spatialheterogeneity of physical properties.To achieve the seamless enforcement of flux continuity and integration ofphysicalmeaning into CNN,a predefined 2D convolutional layer is proposed to accurately express transmissibilitybetween adjacent cells.The efficacy of the proposedmethodwas evaluated through predictions of several petroleumreservoir problems with spatial heterogeneity and compared against state-of-the-art(PINN)through numericalanalysis as a benchmark,which demonstrated the superiority of the proposed method over the PINN.展开更多
Multiphase flow in low permeability porous media is involved in numerous energy and environmental applications.However,a complete description of this process is challenging due to the limited modeling scale and the ef...Multiphase flow in low permeability porous media is involved in numerous energy and environmental applications.However,a complete description of this process is challenging due to the limited modeling scale and the effects of complex pore structures and wettability.To address this issue,based on the digital rock of low permeability sandstone,a direct numerical simulation is performed considering the interphase drag and boundary slip to clarify the microscopic water-oil displacement process.In addition,a dual-porosity pore network model(PNM)is constructed to obtain the water-oil relative permeability of the sample.The displacement efficiency as a recovery process is assessed under different wetting and pore structure properties.Results show that microscopic displacement mechanisms explain the corresponding macroscopic relative permeability.The injected water breaks through the outlet earlier with a large mass flow,while thick oil films exist in rough hydrophobic surfaces and poorly connected pores.The variation of water-oil relative permeability is significant,and residual oil saturation is high in the oil-wet system.The flooding is extensive,and the residual oil is trapped in complex pore networks for hydrophilic pore surfaces;thus,water relative permeability is lower in the water-wet system.While the displacement efficiency is the worst in mixed-wetting systems for poor water connectivity.Microporosity negatively correlates with invading oil volume fraction due to strong capillary resistance,and a large microporosity corresponds to low residual oil saturation.This work provides insights into the water-oil flow from different modeling perspectives and helps to optimize the development plan for enhanced recovery.展开更多
Aqueous foam is broadly applicable to enhanced oil recovery(EOR).The rheology of foam as a function of foam quality,gas and liquid velocities,and surfactant concentration constitute the foundation of its application.T...Aqueous foam is broadly applicable to enhanced oil recovery(EOR).The rheology of foam as a function of foam quality,gas and liquid velocities,and surfactant concentration constitute the foundation of its application.The great variations of the above factors can affect the effectiveness of N2 foam in EOR continuously in complex formations,which is rarely involved in previous relevant studies.This paper presents an experimental study of foam flow in porous media by injecting pre-generated N2 foam into a sand pack under the conditions of considering a wide range of gas and liquid velocities and surfactant concentrations.The results show that in a wide range of gas and liquid velocities,the pressure gradient contours are L-shaped near the coordinate axes,but V-shaped in other regions.And the surfactant concentration is a strong factor influencing the trend of pressure gradient contours.Foam flow resistance is very sensitive to the surfactant concentration in both the high-and low-foam quality regime,especially when the surfactant concentration is less than CMC.The foam quality is an important variable to the flow resistance obtained.There exists a transition point from low-to high-quality regime in a particular flow system,where has the maximum flow resistance,the corresponding foam quality is called transition foam quality,which increases as the surfactant concentration increases.The results can add to our knowledge base of foam rheology in porous media,and can provide a strong basis for the field application of foams.展开更多
Two-phase flow in porous media is a very active field of research,due to its important applications in groundwater pollution,CO_(2)sequestration,or oil and gas production from petroleum reservoirs,just to name a few o...Two-phase flow in porous media is a very active field of research,due to its important applications in groundwater pollution,CO_(2)sequestration,or oil and gas production from petroleum reservoirs,just to name a few of them.Fractional flow equations,which make use of Darcy's law,for describing the movement of two immiscible fluids in a porous medium,are among the most relevant mathematical models in reservoir simulation.This work aims to solve a fractional flow model formed by an elliptic equation,representing the spatial distribution of the pressure,and a hyperbolic equation describing the space-time evolution of water saturation.The numerical solution of the elliptic part is obtained using a finite-element(FE)scheme,while the hyperbolic equation is solved by means of two dif-ferent numerical approaches,both in the finite-volume(FV)framework.One is based on a monotonic upstream-centered scheme for conservation laws(MUSCL)-Hancock scheme,whereas the other makes use of a weighted essentially non-oscillatory(ENO)reconstruc-tion.In both cases,a first-order centered(FORCE)-αnumerical scheme is applied for inter-cell flux reconstruction,which constitutes a new contribution in the field of fractional flow models describing oil-water movement.A relevant feature of this work is the study of the effect of the parameterαon the numerical solution of the models considered.We also show that,in the FORCE-αmethod,when the parameterαincreases,the errors diminish and the order of accuracy is more properly attained,as verified using a manufactured solution technique.展开更多
Extensive improvements in small-scale thermal systems in electronic circuits,automotive industries,and microcomputers conduct the study of microsystems as essential.Flow and thermic field characteristics of the cohere...Extensive improvements in small-scale thermal systems in electronic circuits,automotive industries,and microcomputers conduct the study of microsystems as essential.Flow and thermic field characteristics of the coherent nanofluid-guided microchannel heat sink are described in this perusal.The porous media approximate was used to search the heat distribution in the expanded sheet and Cu:γ-AlOOH/water.A hybrid blend of Boehme copper and aluminum nanoparticles is evaluated to have a cooling effect on the microchannel heat sink.By using Akbari Ganji and finite element methods,linear and non-linear differential equations as well as simple dimensionless equations have been analyzed.The purpose of this study is to investigate the fluid and thermal parameters of copper hybrid solution added to water,such as Nusselt number and Darcy number so that we can reach the best cooling of the fluid.Also,by installing a piece of fin on the wall of the heat sink,the coefficient of conductive heat transfer and displacement heat transfer with the surrounding air fluid increases,and the efficiency of the system increases.The overall results show that expanding values on the NP(series heat transfer fluid system maximizes performance with temperatures)volume division of copper,as well as boehmite alumina particles,lead to a decrease within the stream velocity of the Cu:AlOOH/water.Increasing the volume fraction of nanoparticles in the hybrid mixture decreases the temperature of the solid surface and the hybrid nanofluid.The Brownian movement improves as the volume percentage of nanoparticles in the hybrid mixture grows,spreading the heat across the environment.As a result,heat transmission rates rise.As the Darcy number increases,the thermal field for solid sections and Cu:AlOOH/water improves.展开更多
Since its inception in the 1970s,multi-dimensional magnetic resonance(MR)has emerged as a powerful tool for non-invasive investigations of structures and molecular interactions.MR spectroscopy beyond one dimension all...Since its inception in the 1970s,multi-dimensional magnetic resonance(MR)has emerged as a powerful tool for non-invasive investigations of structures and molecular interactions.MR spectroscopy beyond one dimension allows the study of the correlation,exchange processes,and separation of overlapping spectral information.The multi-dimensional concept has been re-implemented over the last two decades to explore molecular motion and spin dynamics in porous media.Apart from Fourier transform,methods have been developed for processing the multi-dimensional time-domain data,identifying the fluid components,and estimating pore surface permeability via joint relaxation and diffusion spectra.Through the resolution of spectroscopic signals with spatial encoding gradients,multi-dimensional MR imaging has been widely used to investigate the microscopic environment of living tissues and distinguish diseases.Signals in each voxel are usually expressed as multi-exponential decay,representing microstructures or environments along multiple pore scales.The separation of contributions from different environments is a common ill-posed problem,which can be resolved numerically.Moreover,the inversion methods and experimental parameters determine the resolution of multi-dimensional spectra.This paper reviews the algorithms that have been proposed to process multidimensional MR datasets in different scenarios.Detailed information at the microscopic level,such as tissue components,fluid types and food structures in multi-disciplinary sciences,could be revealed through multi-dimensional MR.展开更多
A series of adsorbent materials(WPU-HAx-y)with a three-dimensional porous structure,green sustainability,and excellent performance were prepared and evaluated for the removal of methylene blue using nontoxic and envir...A series of adsorbent materials(WPU-HAx-y)with a three-dimensional porous structure,green sustainability,and excellent performance were prepared and evaluated for the removal of methylene blue using nontoxic and environmentally friendly waterborne polyurethane as the matrix material and humic acid,a biomass material,as the functional material.The newly synthesized adsorbents were characterized by infrared spectroscopy,scanning electron microscopy,specific surface area,and thermogravimetric.The effects of contact time(0-8 h),starting concentration(10-100 mg·L^(-1)),pH(3-11),solution temperature(30-60℃),and coexisting ions(Ca2+,Na+,K+,Mg2+)on the performance were investigated.Pseudo-first-order,pseudo-second-order,elovich,and intra-particle diffusion models were used to analyze the adsorption kinetics;the Langmuir,Freundlich,Temkin,and Dubin-Radushkovich adsorption isotherms were evaluated;and the adsorption behavior of the adsorbent materials was found to be more appropriate for the pseudo-second-order model for chemical pollutant removal than the Langmuir model,which depends on monolayer adsorption.WPU-HA2-3 stood out with a maximum adsorption capacity of 813.0081 mg·g^(-1) fitted to the pseudo-second-order and 309.2832 mg·g^(-1) fitted to the Langmuir model,showing superior adsorption performance and regenerability.展开更多
The seepage characteristics of multiscale porous media is of considerable significance in many scientific and engineering fields.The Darcy permeability is one of the key macroscopic physical properties to characterize...The seepage characteristics of multiscale porous media is of considerable significance in many scientific and engineering fields.The Darcy permeability is one of the key macroscopic physical properties to characterize the seepage capacity of porous media.Therefore,based on the statistically fractal scaling law of porous media,fractal geometry is applied to model the multiscale pore structures.And a two-dimensional fractal orifice-throat model with multiscale and tortuous characteristics is proposed for the seepage flow through porous media.The analytical expression for Darcy permeability of porous media is derived,which is validated by comparing with available experimental data.The results show that the Darcy permeability is significantly influenced by porosity,orifice-throat fractal dimension,minimum to maximum diameter ratio,orifice-throat ratio and tortuosity fractal dimension.The present results are helpful for understanding the seepage mechanism of multiscale porous media,and may provide theoretical basis for unconventional oil and gas exploration and development,porous phase transition energy storage composites,CO2 geological sequestration,environmental protection and nuclear waste treatment,etc.展开更多
Porous materials present significant advantages for absorbing radioactive isotopes in nuclear waste streams.To improve absorption efficiency in nuclear waste treatment,a thorough understanding of the diffusion-advecti...Porous materials present significant advantages for absorbing radioactive isotopes in nuclear waste streams.To improve absorption efficiency in nuclear waste treatment,a thorough understanding of the diffusion-advection process within porous structures is essential for material design.In this study,we present advancements in the volumetric lattice Boltzmann method(VLBM)for modeling and simulating pore-scale diffusion-advection of radioactive isotopes within geopolymer porous structures.These structures are created using the phase field method(PFM)to precisely control pore architectures.In our VLBM approach,we introduce a concentration field of an isotope seamlessly coupled with the velocity field and solve it by the time evolution of its particle population function.To address the computational intensity inherent in the coupled lattice Boltzmann equations for velocity and concentration fields,we implement graphics processing unit(GPU)parallelization.Validation of the developed model involves examining the flow and diffusion fields in porous structures.Remarkably,good agreement is observed for both the velocity field from VLBM and multiphysics object-oriented simulation environment(MOOSE),and the concentration field from VLBM and the finite difference method(FDM).Furthermore,we investigate the effects of background flow,species diffusivity,and porosity on the diffusion-advection behavior by varying the background flow velocity,diffusion coefficient,and pore volume fraction,respectively.Notably,all three parameters exert an influence on the diffusion-advection process.Increased background flow and diffusivity markedly accelerate the process due to increased advection intensity and enhanced diffusion capability,respectively.Conversely,increasing the porosity has a less significant effect,causing a slight slowdown of the diffusion-advection process due to the expanded pore volume.This comprehensive parametric study provides valuable insights into the kinetics of isotope uptake in porous structures,facilitating the development of porous materials for nuclear waste treatment applications.展开更多
CO2 flooding is considered not only one of the most effective enhanced oil recovery (EOR) methods, but also an important alternative for geological CO2 storage. In this paper, the visualization of CO2 flooding was s...CO2 flooding is considered not only one of the most effective enhanced oil recovery (EOR) methods, but also an important alternative for geological CO2 storage. In this paper, the visualization of CO2 flooding was studied using a 400 MHz NMR micro-imaging system. For gaseous CO2 immiscible displacement, it was found that CO2 channeling or fingering occurred due to the difference of fluid viscosity and density. Thus, the sweep efficiency was small and the final residual oil saturation was 53.1%. For supercritical CO2 miscible displacement, the results showed that piston-like displacement occurred, viscous fingering and the gravity override caused by the low viscosity and density of the gas was effectively restrained, and the velocity of CO2 front was uniform. The sweep efficiency was so high that the final residual oil saturation was 33.9%, which indicated CO2 miscible displacement could enhance oil recovery more than CO2 immiscible displacement. In addition, the average velocity of CO2 front was evaluated through analyzing the oil saturation profile. A special core analysis method has been applied to in-situ oil saturation data to directly evaluate the local Darcy phase velocities and capillary dispersion rate.展开更多
Chen's technique of computing synthetic seismograms, which decomposes every vector with a set of basis of orthogonality and completeness before applying the Luco-Apsel-Chen (LAC) generalized reflection and transmis...Chen's technique of computing synthetic seismograms, which decomposes every vector with a set of basis of orthogonality and completeness before applying the Luco-Apsel-Chen (LAC) generalized reflection and transmission coefficients method, is confirmed to be efficient in dealing with elastic waves in multi-layered media and accurate in any frequency range. In this article, we extend Chen's technique to the computation of coupled seismic and electromagnetic (EM) waves in layered porous media. Expanding the involved mechanical and electromagnetic fields by a set of scalar and vector wave-function basis, we obtain the fundamental equations which are subsequently solved by using a recently developed version of the LAC generalized reflection and transmission coefficients method. Our approach and corresponding program is validated by reciprocity tests. We also show a numerical example of a two-layer model with an explosion source. The P-to-EM conversion waves radiated from the interface may have potential application.展开更多
Pore structure of porous media, including pore size and topology, is rather complex. In immiscible twophase displacement process, the capillary force affected by pore size dominates the two-phase flow in the porous me...Pore structure of porous media, including pore size and topology, is rather complex. In immiscible twophase displacement process, the capillary force affected by pore size dominates the two-phase flow in the porous media, affecting displacement results. Direct observation of the flow patterns in the porous media is difficult, and therefore knowledge about the two-phase displacement flow is insufficient. In this paper, a two-dimensional(2D) pore structure was extracted from a sandstone sample, and the flow process that CO_2 displaces resident brine in the extracted pore structure was simulated using the Navier eStokes equation combined with the conservative level set method. The simulation results reveal that the pore throat is a crucial factor for determining CO_2 displacement process in the porous media. The two-phase meniscuses in each pore throat were in a self-adjusting process. In the displacement process,CO_2 preferentially broke through the maximum pore throat. Before breaking through the maximum pore throat, the pressure of CO_2 continually increased, and the curvature and position of two-phase interfaces in the other pore throats adjusted accordingly. Once the maximum pore throat was broken through by the CO_2, the capillary force in the other pore throats released accordingly; subsequently, the interfaces withdrew under the effect of capillary fore, preparing for breaking through the next pore throat.Therefore, the two-phase displacement in CO_2 injection is accompanied by the breaking through and adjusting of the two-phase interfaces.展开更多
Based on the theory of porous media, a general Gurtin variational principle for the initial boundary value problem of dynamical response of fluid-saturated elastic porous media is developed by assuming infinitesimal d...Based on the theory of porous media, a general Gurtin variational principle for the initial boundary value problem of dynamical response of fluid-saturated elastic porous media is developed by assuming infinitesimal deformation and incompressible constituents of the solid and fluid phase. The finite element formulation based on this variational principle is also derived. As the functional of the variational principle is a spatial integral of the convolution formulation, the general finite element discretization in space results in symmetrical differential-integral equations in the time domain. In some situations, the differential-integral equations can be reduced to symmetrical differential equations and, as a numerical example, it is employed to analyze the reflection of one-dimensional longitudinal wave in a fluid-saturated porous solid. The numerical results can provide further understanding of the wave propagation in porous media.展开更多
Streamline simulation is developed to simulate waterflooding in fractured reservoirs. Conventional reservoir simulation methods for fluid flow simulation in large and complex reservoirs are very costly and time consum...Streamline simulation is developed to simulate waterflooding in fractured reservoirs. Conventional reservoir simulation methods for fluid flow simulation in large and complex reservoirs are very costly and time consuming. In streamline method, transport equations are solved on one-dimensional streamlines to reduce the computation time with less memory for simulation. First, pressure equation is solved on an Eulerian grid and streamlines are traced. Defining the "time of flight", saturation equations are mapped and solved on streamlines. Finally, the results are mapped back on Eulerian grid and the process is repeated until the simulation end time. The waterflooding process is considered in a fractured reservoir using the dual porosity model. Afterwards, a computational code is developed to solve the same problem by the IMPES method and the results of streamline simulation are compared to those of the IMPES and a commercial software. Finally, the accuracy and efficiency of streamline simulator for simulation of two-phase flow in fractured reservoirs has been proved.展开更多
Foam is widely used in the petroleum industry thanks to its unique properties and performance. Its application to water control in oil wells has received more and more attention. The stability of nitrogen foam was inv...Foam is widely used in the petroleum industry thanks to its unique properties and performance. Its application to water control in oil wells has received more and more attention. The stability of nitrogen foam was investigated in pressurized equipment and sand pack. The result indicated that with increasing pressure (0-2 MPa) the stability of foam in the pressurized equipment increased linearly. Increased nitrogen injection pressure caused better dispersion of nitrogen-foaming solution in porous media. The initial residual resistance factor to gas was an exponential function of injection pressure, but the residual resistance factor (to gas and liquid) decreased exponentially with time. The halflife of foam in porous media (expressed in residual resistance factor) was much longer than that in bulk phase (expressed in foam height). Pore model analysis indicated that good dispersion in porous media and the presence of thick liquid film during dispersion were the main reasons for high stability. Field test indicated that effective residence of foam in the formation not only resulted in much better heat insulation, but also improved steam stimulation by enhancing steam heating.展开更多
Applying the standard Galerkin finite element method for solving flow problems in porous media encounters some difficulties such as numerical oscillation at the shock front and discontinuity of the velocity field on e...Applying the standard Galerkin finite element method for solving flow problems in porous media encounters some difficulties such as numerical oscillation at the shock front and discontinuity of the velocity field on element faces.Discontinuity of velocity field leads this method not to conserve mass locally.Moreover,the accuracy and stability of a solution is highly affected by a non-conservative method.In this paper,a three dimensional control volume finite element method is developed for twophase fluid flow simulation which overcomes the deficiency of the standard finite element method,and attains high-orders of accuracy at a reasonable computational cost.Moreover,this method is capable of handling heterogeneity in a very rational way.A fully implicit scheme is applied to temporal discretization of the governing equations to achieve an unconditionally stable solution.The accuracy and efficiency of the method are verified by simulating some waterflooding experiments.Some representative examples are presented to illustrate the capability of the method to simulate two-phase fluid flow in heterogeneous porous media.展开更多
基金Project supported by the National Natural Science Foundation of China (Grant No.42074139)the Natural Science Foundation of Jilin Province,China (Grant No.20210101140JC)。
文摘In-situ stress is a common stress in the exploration and development of oil reservoirs. Therefore, it is of great significance to study the propagation characteristics of borehole acoustic waves in fluid-saturated porous media under stress.Based on the acoustoelastic theory of fluid-saturated porous media, the field equation of fluid-saturated porous media under the conditions of confining pressure and pore pressure and the acoustic field formula of multipole source excitation in open hole are given. The influences of pore pressure and confining pressure on guided waves of multipole borehole acoustic field in fluid-saturated porous media are investigated. The numerical results show that the phase velocity and excitation intensity of guided wave increase significantly under the confining pressure. For a given confining pressure, the phase velocity of the guided wave decreases with pore pressure increasing. The excitation intensity of guided wave increases at low frequency and then decreases at high frequency with pore pressure increasing, except for that of Stoneley wave which decreases in the whole frequency range. These results will help us get an insight into the influences of confining pressure and pore pressure on the acoustic field of multipole source in borehole around fluid-saturated porous media.
基金This paper is supported by“National Natural Science Foundation of China(Grant No.42204106)”.
文摘The measurement of nuclear magnetic resonance(NMR)porosity is affected by temperature.Without considering the impact of NMR logging tools,this phenomenon is mainly caused by variations in magnetization intensity of the measured system due to temperature fluctuations and difference between the temperature of the porous medium and calibration sample.In this study,the effect of temperature was explained based on the thermodynamic theory,and the rules of NMR porosity responses to temperature changes were identified through core physics experiments.In addition,a method for correcting the influence of temperature on NMR porosity measurement was proposed,and the possible factors that may affect its application were also discussed.
基金Supported by the National Natural Science Foundation of China(52274048)Beijing Natural Science Foundation Project of China(3222037)Shaanxi Provincial Technical Innovation Project of China(2023-YD-CGZH-02).
文摘Based on the tortuous capillary network model,the relationship between anisotropic permeability and rock normal strain,namely the anisotropic dynamic permeability model(ADPM),was derived and established.The model was verified using pore-scale flow simulation.The uniaxial strain process was calculated and the main factors affecting permeability changes in different directions in the deformation process were analyzed.In the process of uniaxial strain during the exploitation of layered oil and gas reservoirs,the effect of effective surface porosity on the permeability in all directions is consistent.With the decrease of effective surface porosity,the sensitivity of permeability to strain increases.The sensitivity of the permeability perpendicular to the direction of compression to the strain decreases with the increase of the tortuosity,while the sensitivity of the permeability in the direction of compression to the strain increases with the increase of the tortuosity.For layered reservoirs with the same initial tortuosity in all directions,the tortuosity plays a decisive role in the relative relationship between the variations of permeability in all directions during pressure drop.When the tortuosity is less than 1.6,the decrease rate of horizontal permeability is higher than that of vertical permeability,while the opposite is true when the tortuosity is greater than 1.6.This phenomenon cannot be represented by traditional dynamic permeability model.After the verification by experimental data of pore-scale simulation,the new model has high fitting accuracy and can effectively characterize the effects of deformation in different directions on the permeability in all directions.
基金the National Natural Science Foundation of China(No.52274048)Beijing Natural Science Foundation(No.3222037)+1 种基金the CNPC 14th Five-Year Perspective Fundamental Research Project(No.2021DJ2104)the Science Foundation of China University of Petroleum,Beijing(No.2462021YXZZ010).
文摘Recent advances in deep neural networks have shed new light on physics,engineering,and scientific computing.Reconciling the data-centered viewpoint with physical simulation is one of the research hotspots.The physicsinformedneural network(PINN)is currently the most general framework,which is more popular due to theconvenience of constructing NNs and excellent generalization ability.The automatic differentiation(AD)-basedPINN model is suitable for the homogeneous scientific problem;however,it is unclear how AD can enforce fluxcontinuity across boundaries between cells of different properties where spatial heterogeneity is represented bygrid cells with different physical properties.In this work,we propose a criss-cross physics-informed convolutionalneural network(CC-PINN)learning architecture,aiming to learn the solution of parametric PDEs with spatialheterogeneity of physical properties.To achieve the seamless enforcement of flux continuity and integration ofphysicalmeaning into CNN,a predefined 2D convolutional layer is proposed to accurately express transmissibilitybetween adjacent cells.The efficacy of the proposedmethodwas evaluated through predictions of several petroleumreservoir problems with spatial heterogeneity and compared against state-of-the-art(PINN)through numericalanalysis as a benchmark,which demonstrated the superiority of the proposed method over the PINN.
基金supported by National Natural Science Foundation of China(Grant No.42172159)Science Foundation of China University of Petroleum,Beijing(Grant No.2462023XKBH002).
文摘Multiphase flow in low permeability porous media is involved in numerous energy and environmental applications.However,a complete description of this process is challenging due to the limited modeling scale and the effects of complex pore structures and wettability.To address this issue,based on the digital rock of low permeability sandstone,a direct numerical simulation is performed considering the interphase drag and boundary slip to clarify the microscopic water-oil displacement process.In addition,a dual-porosity pore network model(PNM)is constructed to obtain the water-oil relative permeability of the sample.The displacement efficiency as a recovery process is assessed under different wetting and pore structure properties.Results show that microscopic displacement mechanisms explain the corresponding macroscopic relative permeability.The injected water breaks through the outlet earlier with a large mass flow,while thick oil films exist in rough hydrophobic surfaces and poorly connected pores.The variation of water-oil relative permeability is significant,and residual oil saturation is high in the oil-wet system.The flooding is extensive,and the residual oil is trapped in complex pore networks for hydrophilic pore surfaces;thus,water relative permeability is lower in the water-wet system.While the displacement efficiency is the worst in mixed-wetting systems for poor water connectivity.Microporosity negatively correlates with invading oil volume fraction due to strong capillary resistance,and a large microporosity corresponds to low residual oil saturation.This work provides insights into the water-oil flow from different modeling perspectives and helps to optimize the development plan for enhanced recovery.
基金financially supported by National Natural Science Foundation of China(No.U20B6003).
文摘Aqueous foam is broadly applicable to enhanced oil recovery(EOR).The rheology of foam as a function of foam quality,gas and liquid velocities,and surfactant concentration constitute the foundation of its application.The great variations of the above factors can affect the effectiveness of N2 foam in EOR continuously in complex formations,which is rarely involved in previous relevant studies.This paper presents an experimental study of foam flow in porous media by injecting pre-generated N2 foam into a sand pack under the conditions of considering a wide range of gas and liquid velocities and surfactant concentrations.The results show that in a wide range of gas and liquid velocities,the pressure gradient contours are L-shaped near the coordinate axes,but V-shaped in other regions.And the surfactant concentration is a strong factor influencing the trend of pressure gradient contours.Foam flow resistance is very sensitive to the surfactant concentration in both the high-and low-foam quality regime,especially when the surfactant concentration is less than CMC.The foam quality is an important variable to the flow resistance obtained.There exists a transition point from low-to high-quality regime in a particular flow system,where has the maximum flow resistance,the corresponding foam quality is called transition foam quality,which increases as the surfactant concentration increases.The results can add to our knowledge base of foam rheology in porous media,and can provide a strong basis for the field application of foams.
文摘Two-phase flow in porous media is a very active field of research,due to its important applications in groundwater pollution,CO_(2)sequestration,or oil and gas production from petroleum reservoirs,just to name a few of them.Fractional flow equations,which make use of Darcy's law,for describing the movement of two immiscible fluids in a porous medium,are among the most relevant mathematical models in reservoir simulation.This work aims to solve a fractional flow model formed by an elliptic equation,representing the spatial distribution of the pressure,and a hyperbolic equation describing the space-time evolution of water saturation.The numerical solution of the elliptic part is obtained using a finite-element(FE)scheme,while the hyperbolic equation is solved by means of two dif-ferent numerical approaches,both in the finite-volume(FV)framework.One is based on a monotonic upstream-centered scheme for conservation laws(MUSCL)-Hancock scheme,whereas the other makes use of a weighted essentially non-oscillatory(ENO)reconstruc-tion.In both cases,a first-order centered(FORCE)-αnumerical scheme is applied for inter-cell flux reconstruction,which constitutes a new contribution in the field of fractional flow models describing oil-water movement.A relevant feature of this work is the study of the effect of the parameterαon the numerical solution of the models considered.We also show that,in the FORCE-αmethod,when the parameterαincreases,the errors diminish and the order of accuracy is more properly attained,as verified using a manufactured solution technique.
文摘Extensive improvements in small-scale thermal systems in electronic circuits,automotive industries,and microcomputers conduct the study of microsystems as essential.Flow and thermic field characteristics of the coherent nanofluid-guided microchannel heat sink are described in this perusal.The porous media approximate was used to search the heat distribution in the expanded sheet and Cu:γ-AlOOH/water.A hybrid blend of Boehme copper and aluminum nanoparticles is evaluated to have a cooling effect on the microchannel heat sink.By using Akbari Ganji and finite element methods,linear and non-linear differential equations as well as simple dimensionless equations have been analyzed.The purpose of this study is to investigate the fluid and thermal parameters of copper hybrid solution added to water,such as Nusselt number and Darcy number so that we can reach the best cooling of the fluid.Also,by installing a piece of fin on the wall of the heat sink,the coefficient of conductive heat transfer and displacement heat transfer with the surrounding air fluid increases,and the efficiency of the system increases.The overall results show that expanding values on the NP(series heat transfer fluid system maximizes performance with temperatures)volume division of copper,as well as boehmite alumina particles,lead to a decrease within the stream velocity of the Cu:AlOOH/water.Increasing the volume fraction of nanoparticles in the hybrid mixture decreases the temperature of the solid surface and the hybrid nanofluid.The Brownian movement improves as the volume percentage of nanoparticles in the hybrid mixture grows,spreading the heat across the environment.As a result,heat transmission rates rise.As the Darcy number increases,the thermal field for solid sections and Cu:AlOOH/water improves.
基金supported by the National Natural Science Foundation of China(No.61901465,82222032,82172050).
文摘Since its inception in the 1970s,multi-dimensional magnetic resonance(MR)has emerged as a powerful tool for non-invasive investigations of structures and molecular interactions.MR spectroscopy beyond one dimension allows the study of the correlation,exchange processes,and separation of overlapping spectral information.The multi-dimensional concept has been re-implemented over the last two decades to explore molecular motion and spin dynamics in porous media.Apart from Fourier transform,methods have been developed for processing the multi-dimensional time-domain data,identifying the fluid components,and estimating pore surface permeability via joint relaxation and diffusion spectra.Through the resolution of spectroscopic signals with spatial encoding gradients,multi-dimensional MR imaging has been widely used to investigate the microscopic environment of living tissues and distinguish diseases.Signals in each voxel are usually expressed as multi-exponential decay,representing microstructures or environments along multiple pore scales.The separation of contributions from different environments is a common ill-posed problem,which can be resolved numerically.Moreover,the inversion methods and experimental parameters determine the resolution of multi-dimensional spectra.This paper reviews the algorithms that have been proposed to process multidimensional MR datasets in different scenarios.Detailed information at the microscopic level,such as tissue components,fluid types and food structures in multi-disciplinary sciences,could be revealed through multi-dimensional MR.
基金supported by the National Natural Science Foundation of China(21704047)the Natural Science Foundation of Shandong Province(ZR2017BB078,ZR2021QE137)+1 种基金the Foundation of State Key Laboratory of Biobased Material and Green Papermaking(ZZ20190407)the Major scientific and technological innovation projects of Shandong Province(2019JZZY020230).
文摘A series of adsorbent materials(WPU-HAx-y)with a three-dimensional porous structure,green sustainability,and excellent performance were prepared and evaluated for the removal of methylene blue using nontoxic and environmentally friendly waterborne polyurethane as the matrix material and humic acid,a biomass material,as the functional material.The newly synthesized adsorbents were characterized by infrared spectroscopy,scanning electron microscopy,specific surface area,and thermogravimetric.The effects of contact time(0-8 h),starting concentration(10-100 mg·L^(-1)),pH(3-11),solution temperature(30-60℃),and coexisting ions(Ca2+,Na+,K+,Mg2+)on the performance were investigated.Pseudo-first-order,pseudo-second-order,elovich,and intra-particle diffusion models were used to analyze the adsorption kinetics;the Langmuir,Freundlich,Temkin,and Dubin-Radushkovich adsorption isotherms were evaluated;and the adsorption behavior of the adsorbent materials was found to be more appropriate for the pseudo-second-order model for chemical pollutant removal than the Langmuir model,which depends on monolayer adsorption.WPU-HA2-3 stood out with a maximum adsorption capacity of 813.0081 mg·g^(-1) fitted to the pseudo-second-order and 309.2832 mg·g^(-1) fitted to the Langmuir model,showing superior adsorption performance and regenerability.
文摘The seepage characteristics of multiscale porous media is of considerable significance in many scientific and engineering fields.The Darcy permeability is one of the key macroscopic physical properties to characterize the seepage capacity of porous media.Therefore,based on the statistically fractal scaling law of porous media,fractal geometry is applied to model the multiscale pore structures.And a two-dimensional fractal orifice-throat model with multiscale and tortuous characteristics is proposed for the seepage flow through porous media.The analytical expression for Darcy permeability of porous media is derived,which is validated by comparing with available experimental data.The results show that the Darcy permeability is significantly influenced by porosity,orifice-throat fractal dimension,minimum to maximum diameter ratio,orifice-throat ratio and tortuosity fractal dimension.The present results are helpful for understanding the seepage mechanism of multiscale porous media,and may provide theoretical basis for unconventional oil and gas exploration and development,porous phase transition energy storage composites,CO2 geological sequestration,environmental protection and nuclear waste treatment,etc.
基金supported as part of the Center for Hierarchical Waste Form Materials,an Energy Frontier Research Center funded by the U.S.Department of Energy,Office of Science,Basic Energy Sciences under Award No.DE-SC0016574.
文摘Porous materials present significant advantages for absorbing radioactive isotopes in nuclear waste streams.To improve absorption efficiency in nuclear waste treatment,a thorough understanding of the diffusion-advection process within porous structures is essential for material design.In this study,we present advancements in the volumetric lattice Boltzmann method(VLBM)for modeling and simulating pore-scale diffusion-advection of radioactive isotopes within geopolymer porous structures.These structures are created using the phase field method(PFM)to precisely control pore architectures.In our VLBM approach,we introduce a concentration field of an isotope seamlessly coupled with the velocity field and solve it by the time evolution of its particle population function.To address the computational intensity inherent in the coupled lattice Boltzmann equations for velocity and concentration fields,we implement graphics processing unit(GPU)parallelization.Validation of the developed model involves examining the flow and diffusion fields in porous structures.Remarkably,good agreement is observed for both the velocity field from VLBM and multiphysics object-oriented simulation environment(MOOSE),and the concentration field from VLBM and the finite difference method(FDM).Furthermore,we investigate the effects of background flow,species diffusivity,and porosity on the diffusion-advection behavior by varying the background flow velocity,diffusion coefficient,and pore volume fraction,respectively.Notably,all three parameters exert an influence on the diffusion-advection process.Increased background flow and diffusivity markedly accelerate the process due to increased advection intensity and enhanced diffusion capability,respectively.Conversely,increasing the porosity has a less significant effect,causing a slight slowdown of the diffusion-advection process due to the expanded pore volume.This comprehensive parametric study provides valuable insights into the kinetics of isotope uptake in porous structures,facilitating the development of porous materials for nuclear waste treatment applications.
基金support from the National High Technology Reseatch and Development Program of China(863 Program,Grant No.2008AA062303 and No.2009AA063402)National Basic Research Program of China(973 Program,Grant No.2006CB705804)the National Natural Science Foundation of China (Key Program,Grant No.50736001)
文摘CO2 flooding is considered not only one of the most effective enhanced oil recovery (EOR) methods, but also an important alternative for geological CO2 storage. In this paper, the visualization of CO2 flooding was studied using a 400 MHz NMR micro-imaging system. For gaseous CO2 immiscible displacement, it was found that CO2 channeling or fingering occurred due to the difference of fluid viscosity and density. Thus, the sweep efficiency was small and the final residual oil saturation was 53.1%. For supercritical CO2 miscible displacement, the results showed that piston-like displacement occurred, viscous fingering and the gravity override caused by the low viscosity and density of the gas was effectively restrained, and the velocity of CO2 front was uniform. The sweep efficiency was so high that the final residual oil saturation was 33.9%, which indicated CO2 miscible displacement could enhance oil recovery more than CO2 immiscible displacement. In addition, the average velocity of CO2 front was evaluated through analyzing the oil saturation profile. A special core analysis method has been applied to in-situ oil saturation data to directly evaluate the local Darcy phase velocities and capillary dispersion rate.
基金supported by the Natural R&D Special Fund for Public Welfare Industry(No.200808069)National Natural Science Foundation of China(Nos.40974038,40774028 and 40821062)
文摘Chen's technique of computing synthetic seismograms, which decomposes every vector with a set of basis of orthogonality and completeness before applying the Luco-Apsel-Chen (LAC) generalized reflection and transmission coefficients method, is confirmed to be efficient in dealing with elastic waves in multi-layered media and accurate in any frequency range. In this article, we extend Chen's technique to the computation of coupled seismic and electromagnetic (EM) waves in layered porous media. Expanding the involved mechanical and electromagnetic fields by a set of scalar and vector wave-function basis, we obtain the fundamental equations which are subsequently solved by using a recently developed version of the LAC generalized reflection and transmission coefficients method. Our approach and corresponding program is validated by reciprocity tests. We also show a numerical example of a two-layer model with an explosion source. The P-to-EM conversion waves radiated from the interface may have potential application.
基金supported by the National High Technology Research and Development (863) Program of China (Grant Nos.2006AA09A209-5)the National Natural Science Foundation of China (Grant Nos. 90510003)the Major Research Project of the Ministry of Education (Grant Nos. 306005)
基金funded by Key Laboratory of Coal-based CO_2 Capture and Geological Storage,Jiangsu Province,ChinaUS Advanced Coal Technology Consortium(No.2013 DFB60140-08)
文摘Pore structure of porous media, including pore size and topology, is rather complex. In immiscible twophase displacement process, the capillary force affected by pore size dominates the two-phase flow in the porous media, affecting displacement results. Direct observation of the flow patterns in the porous media is difficult, and therefore knowledge about the two-phase displacement flow is insufficient. In this paper, a two-dimensional(2D) pore structure was extracted from a sandstone sample, and the flow process that CO_2 displaces resident brine in the extracted pore structure was simulated using the Navier eStokes equation combined with the conservative level set method. The simulation results reveal that the pore throat is a crucial factor for determining CO_2 displacement process in the porous media. The two-phase meniscuses in each pore throat were in a self-adjusting process. In the displacement process,CO_2 preferentially broke through the maximum pore throat. Before breaking through the maximum pore throat, the pressure of CO_2 continually increased, and the curvature and position of two-phase interfaces in the other pore throats adjusted accordingly. Once the maximum pore throat was broken through by the CO_2, the capillary force in the other pore throats released accordingly; subsequently, the interfaces withdrew under the effect of capillary fore, preparing for breaking through the next pore throat.Therefore, the two-phase displacement in CO_2 injection is accompanied by the breaking through and adjusting of the two-phase interfaces.
基金Project supported by the National Nattural Science Foundation of China(No.10272070)
文摘Based on the theory of porous media, a general Gurtin variational principle for the initial boundary value problem of dynamical response of fluid-saturated elastic porous media is developed by assuming infinitesimal deformation and incompressible constituents of the solid and fluid phase. The finite element formulation based on this variational principle is also derived. As the functional of the variational principle is a spatial integral of the convolution formulation, the general finite element discretization in space results in symmetrical differential-integral equations in the time domain. In some situations, the differential-integral equations can be reduced to symmetrical differential equations and, as a numerical example, it is employed to analyze the reflection of one-dimensional longitudinal wave in a fluid-saturated porous solid. The numerical results can provide further understanding of the wave propagation in porous media.
文摘Streamline simulation is developed to simulate waterflooding in fractured reservoirs. Conventional reservoir simulation methods for fluid flow simulation in large and complex reservoirs are very costly and time consuming. In streamline method, transport equations are solved on one-dimensional streamlines to reduce the computation time with less memory for simulation. First, pressure equation is solved on an Eulerian grid and streamlines are traced. Defining the "time of flight", saturation equations are mapped and solved on streamlines. Finally, the results are mapped back on Eulerian grid and the process is repeated until the simulation end time. The waterflooding process is considered in a fractured reservoir using the dual porosity model. Afterwards, a computational code is developed to solve the same problem by the IMPES method and the results of streamline simulation are compared to those of the IMPES and a commercial software. Finally, the accuracy and efficiency of streamline simulator for simulation of two-phase flow in fractured reservoirs has been proved.
文摘Foam is widely used in the petroleum industry thanks to its unique properties and performance. Its application to water control in oil wells has received more and more attention. The stability of nitrogen foam was investigated in pressurized equipment and sand pack. The result indicated that with increasing pressure (0-2 MPa) the stability of foam in the pressurized equipment increased linearly. Increased nitrogen injection pressure caused better dispersion of nitrogen-foaming solution in porous media. The initial residual resistance factor to gas was an exponential function of injection pressure, but the residual resistance factor (to gas and liquid) decreased exponentially with time. The halflife of foam in porous media (expressed in residual resistance factor) was much longer than that in bulk phase (expressed in foam height). Pore model analysis indicated that good dispersion in porous media and the presence of thick liquid film during dispersion were the main reasons for high stability. Field test indicated that effective residence of foam in the formation not only resulted in much better heat insulation, but also improved steam stimulation by enhancing steam heating.
基金Iranian Offshore Oil Company (IOOC) for financial support of this work
文摘Applying the standard Galerkin finite element method for solving flow problems in porous media encounters some difficulties such as numerical oscillation at the shock front and discontinuity of the velocity field on element faces.Discontinuity of velocity field leads this method not to conserve mass locally.Moreover,the accuracy and stability of a solution is highly affected by a non-conservative method.In this paper,a three dimensional control volume finite element method is developed for twophase fluid flow simulation which overcomes the deficiency of the standard finite element method,and attains high-orders of accuracy at a reasonable computational cost.Moreover,this method is capable of handling heterogeneity in a very rational way.A fully implicit scheme is applied to temporal discretization of the governing equations to achieve an unconditionally stable solution.The accuracy and efficiency of the method are verified by simulating some waterflooding experiments.Some representative examples are presented to illustrate the capability of the method to simulate two-phase fluid flow in heterogeneous porous media.