Influence of the Partial Substitution of Bitumen by a Mixture of Sulphur and Tyre and Plastic Bottle Powders on the Behaviour of Bituminous Concrete

This article deals with the influence of the partial substitution of bitumen by a mixture of sulphur and tyre and plastic bottle powders on the characterization of asphalt concrete. The approach adopted was to subject a control asphalt concrete to level 2 formulation tests as well as those modified at 10%, 20%, 30% and 40% by substituting bitumen with a mixture of tyre powder, plastic bottle powder and sulphur at 40%, 28% and 32% respectively. The results of the PCG, Duriez and rutting tests carried out on the control and modified bituminous concretes (manufactured using the wet process) revealed three (03) major findings, in particular with regard to workability, resistance to simple compression and rutting. The experimental results show an increasing trend in the essential parameters. At 40% substitution, there was a 22.73% increase in compactness, reflecting a significant improvement in the material’s workability. With regard to simple compressive strength, the increase is 34.02% at 40% substitution, highlighting the limitation of crack formation and propagation under heavy precipitation. With regard to rutting, the 16% drop in susceptibility at 40% substitution reflects a significant improvement in the behaviour of the material under dynamic mechanical stresses in heavy precipitation. The improvement in these behaviours results from the insertion of the plastic bottle powder into the interstices of the granular skeleton, thus reducing its cellular structure, and also from the interactions between the sulphur with the tyre powder and the sulphur with the plastic bottle powder, i.e. cross-linking or vulcanisation.

On Numerical Modelling of Industrial Powder Compaction Processes for Large Deformation of Endochronic Plasticity at Finite Strains

Compaction processes are one the most important par ts of powder forming technology. The main applications are focused on pieces for a utomotive, aeronautic, electric and electronic industries. The main goals of the compaction processes are to obtain a compact with the geometrical requirements, without cracks, and with a uniform distribution of density. Design of such proc esses consist, essentially, in determine the sequence and relative displacements of die and punches in order to achieve such goals. A.B. Khoei presented a gener al framework for the finite element simulation of powder forming processes based on the following aspects; a large displacement formulation, centred on a total and updated Lagrangian formulation; an adaptive finite element strategy based on error estimates and automatic remeshing techniques; a cap model based on a hard ening rule in modelling of the highly non-linear behaviour of material; and the use of an efficient contact algorithm in the context of an interface element fo rmulation. In these references, the non-linear behaviour of powder was adequately desc ribed by the cap plasticity model. However, it suffers from a serious deficiency when the stress-point reaches a yield surface. In the flow theory of plasticit y, the transition from an elastic state to an elasto-plastic state appears more or less abruptly. For powder material it is very difficult to define the locati on of yield surface, because there is no distinct transition from elastic to ela stic-plastic behaviour. Results of experimental test on some hard met al powder show that the plastic effects were begun immediately upon loading. In such mater ials the domain of the yield surface would collapse to a point, so making the di rection of plastic increment indeterminate, because all directions are normal to a point. Thus, the classical plasticity theory cannot deal with such materials and an advanced constitutive theory is necessary. In the present paper, the constitutive equations of powder materials will be discussed via an endochronic theory of plasticity. This theory provides a unifi ed point of view to describe the elastic-plastic behaviour of material since it places no requirement for a yield surface and a ’loading function’ to disting uish between loading an unloading. Endochronic theory of plasticity has been app lied to a number of metallic materials, concrete and sand, but to the knowledge of authors, no numerical scheme of the model has been applied to powder material . In the present paper, a new approach is developed based on an endochronic rate independent, density-dependent plasticity model for describing the isothermal deformation behavior of metal powder at low homologous temperature. Although the concept of yield surface has not been explicitly assumed in endochronic theory, it is shown that the cone-cap plasticity yield surface (Fig.1), which is the m ost commonly used plasticity models for describing the behavior of powder materi al can be easily derived as a special case of the proposed endochronic theory. Fig.1 Trace of cone-cap yield function on the meridian pl ane for different relative density As large deformation is observed in powder compaction process, a hypoelastic-pl astic formulation is developed in the context of finite deformation plasticity. Constitutive equations are stated in unrotated frame of reference that greatly s implifies endochronic constitutive relation in finite plasticity. Constitutive e quations of the endochronic theory and their numerical integration are establish ed and procedures for determining material parameters of the model are demonstra ted. Finally, the numerical schemes are examined for efficiency in the model ling of a tip shaped component, as shown in Fig.2. Fig.2 A shaped tip component. a) Geometry, boundary conditio n and finite element mesh; b) density distribution at final stage of

Thermal debinding dynamics of novel binder system

The thermal debinding dynamics of newly developed binders for cemented carbides extrusion molding was studied. It is shown that the thermal debinding processes can be divided into two stages: low temperature region, in which the low molecular mass components (LMMCs) are removed; and high temperature region, in which the polymer components are removed. The rate of thermal debinding is controlled by diffusion mechanism. The thermal debinding activation energies were solved out by differential method and integral method. The results show that the addition of other components acted as a catalyzer can effectively decrease the activation energy of thermal debinding processes.

Preparation of baicalin colon-targeted granules and its intervention effect on ulcerative colitis in rats

Baicalin(BA)is a flavonoid extracted from the dried root of Scutellaria baicalensis Georgi with excellent antioxidant and anti-inflammatory biological activities.In this study,Eudragit S100 was used as the colonic target material to prepare BA colonic targeting granules(EBCGs)based on plasticizer dry powder coating technology to improve the targeting transportation performance of BA.In vitro studies showed that EBCGs with pH-sensitive properties were successfully prepared by plasticizer dry powder coating,and in vivo animal imaging studies showed that EBCGs could deliver BA to the colon and inhibit the release of BA in the upper gastrointestinal tract(GIT).In vivo studies showed that EBCGs had good therapeutic effects in colitis,which reduced expression levels of tumor necrosis factor alpha(TNF-α)and interleukin-1β(IL-1β)and increased superoxide dismutase(SOD)activities in the colonic tissues of rats with colitis.In conclusion,Eudragit S100 could be used for the preparation of multi-unit oral colon-targeted formulations by plasticizer dry powder coating technology,and our prepared EBCGs had good colon-targeting properties,which could improve the therapeutic effect and provide a potential application for ulcerative colitis(UC).

An update on electrostatic powder coating for pharmaceuticals

Derived from dry powder coating of metals, electrostatic powder coating for pharmaceuticals is a technology for coating drug solid dosage forms. In this technology, coating powders, containing coating polymers, pigments, and other excipients, are directly sprayed onto the surface of the solid dosage forms through an electrostatic gun without using any organic solvent or water. The deposited coating powders are further cured to form a coating film. Electrostatic powder coating technology has many advantages compared to other pharmaceutical coating methods. It can eliminate the limitations caused by the organic solvent in solvent coating such as environmental issues and health problems. And electrostatic powder coating technology also surpasses aqueous coating due to its shorter processing time and less energy consumption, leading to a lower overall cost. Furthermore, the utilization of electrical attraction can promote the movement of coating powders towards the substrate, leading to an enhanced coating powder adhesion and coating efficiency, which make it more promising compared to other dry coating technologies. The objective of this review is to summarize the coating principles, apparatus, and formulations of different electrostatic powder coating technologies, giving their advantages and limitations and also analyzing the future application in the industry for each technology