Operation and Development of Grid-Integrated Jiuquan Wind Power Base

In this paper the author describes the current development of tbe 10-GW wind power base in Jiuquan, Gansu Province. The.future planning of the wind power base and the relevant power grid are also introduced based on the assessment on the wind resources and the wind power operation with the grid.

Challenges of Power Delivery from Jiuquan Wind Power Base

The 10-GW-class Jiuquan Wind Power Base in Gansu Province is to get its Phase I Project completed soon, and will further expand and become the world largest wind power base in the future. Whether electricity from the wind power base can be delivered on such a large scale becomes the focus of attention of the world. This paper analyzes four challenges facing the wind power base, including transmission capability, peak regulation and frequency modulation, capacity balance and generation accommodation, as well as system stability.

Synthetical Efficiency-based Optimization for the Power Distribution of Power-split Hybrid Electric Vehicles

Now the optimization strategies for power distribution are researched widely, and most of them are aiming to the optimal fuel economy and the driving cycle must be preknown. Thus if the actual driving condition deviates from the scheduled driving cycle, the effect of optimal results will be declined greatly. Therefore, the instantaneous optimization strategy carried out on-line is studied in this paper. The power split path and the transmission efficiency are analyzed based on a special power-split scheme and the efficiency models of the power transmitting components are established. The synthetical efficiency optimization model is established for enhancing the transmission efficiency and the fuel economy. The identification of the synthetical efficiency as the optimization objective and the constrain group are discussed emphatically. The optimization is calculated by the adaptive simulated annealing （ASA） algorithm and realized on-line by the radial basis function （RBF）-based similar models. The optimization for power distribution of the hybrid vehicle in an actual driving condition is carried out and the road test results are presented. The test results indicate that the synthetical efficiency optimization method can enhance the transmission efficiency and the fuel economy of the power-split hybrid electric vehicle （HEV） observably. Compared to the rules-based strategy the optimization strategy is optimal and achieves the approximate global optimization solution for the power distribution. The synthetical efficiency optimization solved by ASA algorithm can give attentions to both optimization quality and calculation efficiency, thus it has good application foreground for the power distribution of power-split HEV.

Basic Concept and Theoretical Study of Condition-based Maintenance for Power Transmission System

状态检修背景下,为解决电网运行整体与输变电设备个体之间的矛盾和冲突,在已有研究成果基础上,提出电网状态检修的概念,在输变电设备状态检修决策过程中,给出电网故障风险和电网检修风险的定义以及相应的量化表达式。依据设备状态预测,以电网故障风险和电网检修风险的和最小为目标,将设备检修、运行以及电网整体性能在概率引导下相互牵制,形成电网状态检修的数学模型,并给出相应的解决方法。最后,为验证该理论研究的可行性,分别以可靠性测试系统RBTS-BUS6和IEEE-RTS79系统为例,对各种情况进行分析,体现了预期的效果,并期望为电网检修与运行协调决策理论的深入研究提供必要的理论基础。

Design Technologies for Silicon-Based High-Efficiency RF Power Amplifiers:A Brief Overview

This paper presents a brief overview of several promising design technologies for high efficiency silicon-based radio frequency （RF） power amplifiers （PAs） as well as the use of these technologies in mobile broadband wireless communications. Four important aspects of PA design are addressed in this paper. First, we look at class-E PA design equations and provide an example of a class-E PA that achieves efficiency of 65-70% at 2.4 GHz. Then, we discuss state-of-the-art envelope tracking （ET） design for monolithic wideband RF mobile transmitter applications. A brief overview of Doherty PA design for the next-generation wireless handset applications is then given. Towards the end of the paper, we discuss an inherently broadband and highly efficient class-J PA design targeting future multi-band multi-standard wireless communication protocols.

Design of a Broadband E-Plane Power Combiner Based on Quarter-Arc Bent Rectangular Waveguides for Sub-THz and THz Wave

A method of designing an E-plane power combiner composed of two quarter-arc bent rectangular waveguides is proposed for sub-THz and THz waves. The quarter-arc bent-waveguide power combiner has a simple geometry which is easy to design and fabricate. By HFSS codes, the physical mechanism and performance of the power combiner are analyzed, and the relationship between the output characteristics and the structure/operating parameters is given. Simulation results show that our power combiner is suitable for the combining of two equalpower and reversed-phase signals, the bandwidth of the combiner is wide and can be adjusted by the radius of the quarter-arc, and the isolation performance of the combiner can be improved by adding thin film resistive septa at the junction of two quarter-arc bent waveguides. Meanwhile, an approximate method based on the analytic geometrical analysis is given to design this power combiner for different frequency bands.

The Wireless Power Transmission on the Wristto-Forehead Path Based on the Body Channel

The body channel based wireless power transfer(BC-WPT)method utilizes the human body as the medium to transfer power for bioelectronics,which can achieve a lower transmission loss due to its higher conductivity.However,except for the channel length,different on-body loca-tions of the transmitter and receiver also influence the power supply performance.This paper fo-cuses on the wrist-to-forehead path to show the potential of BC-WPT for the brain bioelectronics such as the brain computer interface device.The channel characteristics from 10 MHz to 60 MHz are measured by a vector network analyzer(VNA)and a prototype BC-WPT system with differ-ent copper electrodes and the lowest power loss locates between-22 dB and-33 dB.Furthermore,the minimum path loss limit is simulated in Advanced Design System(ADS)software and the low-est optimum path loss can reach nearly-13 dB.Finally,a rectifier circuit is also built at the receiv-er side to harvest d.c.voltage.The results show that the open-circuit voltage(OCV)can reach 1.75 V with the transmitter of 50Ωoutput impedance supplying 5V_(pp)sine voltage at 60 MHz when adopt-ing 1 cm-diameter circular electrodes.

Placido disk-based topography versus high-resolution rotating Scheimpflug camera for corneal power measurements in keratoconic and post-LASIK eyes：reliability and agreement

AIM：To compare the repeatability/reproducibility of measurement by high-resolution Placido disk-based topography with that of a high-resolution rotating Scheimpflug camera and assess the agreement between the two instruments in measuring corneal power in eyes with keratoconus and post-laser in situ keratomileusis（LASIK）. METHODS：One eye each of 36 keratoconic patients and 20 subjects who had undergone LASIK was included in this prospective observational study. Two independent examiners worked in a random order to take three measurements of each eye with both instruments. Four parameters were measured on the anterior cornea：steep keratometry（Ks）,flat keratometry（Kf）,mean keratometry（Km）,and astigmatism（Ks-Kf）. Intra-examiner repeatability and inter-examiner reproducibility were evaluated by calculating the within-subject standard deviation（Sw）the coefficient of repeatability（R）,the coefficient of variation（Co V）,and the intraclass correlation coefficient（ICC）. Agreement between instruments was tested with the BlandAltman method by calculating the 95% limits of agreement（95% Lo A）.RESULTS：In keratoconic eyes,the intra-examiner and inter-examiner ICC were 〉0.95. As compared with measurement by high-resolution Placido disk-based topography,the intra-examiner R of the high-resolution rotating Scheimpflug camera was lower for Kf（0.32 vs 0.88）,Ks（0.61 vs 0.88）,and Km（0.32 vs 0.84）but higher for Ks-Kf（0.70 vs 0.57）. Inter-examiner R values were lower for all parameters measured using the high-resolution rotating Scheimpflug camera. The 95% Lo A were-1.28 to ＋0.55 for Kf,-1.36 to ＋0.99 for Ks,-1.08 to ＋0.50 for Km,and-1.11 to ＋1.48 for Ks-Kf. In the post-LASIK eyes,the intra-examiner andinter-examiner ICC were 〉0.87 for all parameters. The intra-examiner and inter-examiner R were lower for all parameters measured using the high-resolution rotating Scheimpflug camera. The intra-examiner R was 0.17 vs 0.88 for Kf,0.21 vs 0.88 for Ks,0.17 vs 0.86 for Km,and 0.28 vs 0.33 for Ks-Kf. The inter-examiner R was 0.09 vs 0.64 for Kf,0.15 vs 0.56 for Ks,0.09 vs 0.59 for Km,and 0.18 vs 0.23 for Ks-Kf. The 95% Lo A were-0.54 to ＋0.58 for Kf,-0.51 to ＋0.53 for Ks and Km,and-0.28 to ＋0.27 for Ks-Kf. CONCLUSION：As compared with Placido disk-based topography,the high-resolution rotating Scheimpflug camera provides more repeatable and reproducible measurements of Ks,Kf and Ks in keratoconic and post-LASIK eyes. Agreement between instruments is fair in keratoconus and very good in post-LASIK eyes.

A Clean Technology for Future Prospective: Emission Modeling of Gas Based Power Plant

The aim of present research is to study the dispersion of air pollutants using the air quality model, AERMOD and to predict the impact of pollutants (PM10, NO2 and CO) at the receptor level released from Gas Based Power Plant (GBPP). The net-concentrations including monitored data plus predicted values of PM10, NO2 and CO would be increased from base value 75 to 77.61 μg/m3 with an increase of 3.48%, 22 to 26.66 μg/m3 with an increase of 21.18% and 428 to 538.37 μg/m3 with an increase of 25.79% respectively. The study of hill effect showed that it had profound impact upon the dispersion of pollutants and the ratio (with hill and without hill) of each pollutant was 3.89 for PM10 (24 hr), 2.40 for NO2 (24 hr) and 13.98 for CO (1 hr). The natural gas based plant not only decreases the pollution level but also reduces the hospital treatment cost and protects the public health. The modeling results suggest that the GBPP could be a clean technology as replacement of coal power plants located in the city which pollute the environment considerably in spite of control measures installed.

煤电化基地大宗固废“三化”协同利用基础与技术

我国14个大型煤炭基地及89个大宗固体废弃物综合利用示范基地建设,标志着矿区大宗固废利用已被纳入全国战略发展布局。长期以来煤炭资源高强度的开发与利用,造成矿区浅埋煤层资源临近枯竭,煤电化基地大规模固废堆积及地表沉陷,已成为制约矿区绿色低碳、高质量发展的难题。大宗煤基固废协同利用与绿色充填是解放“三下一上”压煤,延长矿井服务年限,实现固废无害化、资源化、规模化“三化”利用的有效途径。基于产煤大省山西省、“华东能源粮仓”安徽两淮基地及宁东能源化工基地的煤基固废种类和产量,详细阐述了以煤矸石、粉煤灰、炉底渣、气化渣和脱硫石膏等为主要材料的煤基固废通过重金属吸附解吸和络合钝化技术实现无害化处置,列举煤基固废分类应用于低热值煤基固废发电、制备建筑材料如水泥、砖瓦等资源化利用途径,对比分析煤基固废采煤沉陷区复垦回填及井下充填规模化利用途径,突出煤基固废井下充填的优越性。基于煤电化基地深部煤炭资源,提出绿色充填开采理论与关键技术,包括深部煤矸石源头减量与采选充协同技术、充填材料高效制备与深部井下输送技术及煤基固废充填材料深部多场耦合机理,探究多源煤基固废从源头、过程到终端的深部充填开采全过程的技术原理与方法,以解决矿区深部井下充填的技术难题。根据宁东基地任家庄煤矿、山西省霍尔辛赫煤矿及淮北矿区地质条件和充填目的,分别提出超前钻孔注充低位充填方案、关键层非典型特征条件下多离层梯级注浆方案和煤基固废协同利用关键技术,综合矿山固废处置与利用、深部煤炭资源开发利用、地表沉陷控制、生态环境保护等优势,形成煤电化基地大宗固废协同利用与绿色开采模式,为煤炭开采高质量化和环境低损伤化提供参考。

Field plate structural optimization for enhancing the power gain of GaN-based HEMTs

A novel source-connected field plate structure, featuring the same photolithography mask as the gate electrode, is proposed as an improvement over the conventional field plate （FP） techniques to enhance the frequency performance in GaN-based HEMTs. The influences of the field plate on frequency and breakdown performance are investigated simul- taneously by using a two-dimensional physics-based simulation. Compared with the conventional T-gate structures with a field plate length of 1.2 gm, this field plate structure can induce the small signal power gain at 10 GHz to increase by 5-9.5 dB, which depends on the distance between source FP and dramatically shortened gate FE This technique minimizes the parasitic capacitances, especially the gate-to-drain capacitance, showing a substantial potential for millimeter-wave, high power applications.

The Development of Network based Composite Power quality Regulation Device

First, the paper analyzes the advantages and disadvantages of all kinds of reactive power compensation technology, and then proposes a principle and integrated control strategy of the composite operation of TSC and SVG, also the paper designs and develops the main controller of Network based composite power quality regulation device, based on RTDS, the real-time digital simulation model of The Device is established, and finally the prototype of the device is developed with the function of filter and split-phase compensation. The main controller determines the cooperative operation of both TSC and SVG, and the switching strategy of TSC. The simulation result in RTDS can verify the precision of the measure system and the validity of the control logic, the prototype has finished the type test according to the national standard.

海上风电产业发展趋势与Power to X模式应用

文章对海上风电各国总体发展现状及未来发展趋势进行分析,表明各国都在加强对海上风电开发利用,但随着海上风电高速发展,有限的近海风电资源开发趋于饱和,深远海域风电成为海上风电未来发展的方向。然而水深离岸远,深远海风能开发困难,难于实现商业化。文章介绍了一种将新能源电力转换为其他能源载体的Power to X模式。氢作为1种可再生能源载体,可基于Power to X模式,通过将新能源电力电解水制氢的方式,有效降低深远海风电的成本。

坚持和发展民主集中制原则推进新时代中国刑事诉讼制度现代化

全国人大已将《刑事诉讼法》的修改列入本届人大的工作规划之中。作为规范刑事诉讼程序、约束诉讼主体行为的基本法律,应该明确刑事诉讼中公权力机关之间职能分工的工作原则。民主集中制是我国《宪法》规定的国家机构组织和活动原则,同时也是我国现行刑事诉讼确立的公权力机关之间职能分工的指导原则,具体表现为公检法等机关在刑事诉讼中“分工负责、互相配合、互相制约”的工作原则。民主集中制决定了我国刑事诉讼中权力的集中本位及其分工的相对性。新时代应该发展刑事诉讼中的民主集中制原则,顺应权力本位向权利本位转变的时代潮流,以实现民主集中制原则与刑事诉讼制度的根本自洽,推进刑事诉讼现代化。

Online Learning Control for Harmonics Reduction Based on Current Controlled Voltage Source Power Inverters

Nonlinear loads in the power distribution system cause non-sinusoidal currents and voltages with harmonic components.Shunt active filters(SAF) with current controlled voltage source inverters(CCVSI) are usually used to obtain balanced and sinusoidal source currents by injecting compensation currents.However,CCVSI with traditional controllers have a limited transient and steady state performance.In this paper,we propose an adaptive dynamic programming(ADP) controller with online learning capability to improve transient response and harmonics.The proposed controller works alongside existing proportional integral(PI) controllers to efficiently track the reference currents in the d-q domain.It can generate adaptive control actions to compensate the PI controller.The proposed system was simulated under different nonlinear(three-phase full wave rectifier) load conditions.The performance of the proposed approach was compared with the traditional approach.We have also included the simulation results without connecting the traditional PI control based power inverter for reference comparison.The online learning based ADP controller not only reduced average total harmonic distortion by 18.41%,but also outperformed traditional PI controllers during transients.

Interference Management for DS-CDMA Systems through Closed-Loop Power Control, Base Station Assignment, and Beamforming

In this paper, we propose a smart step closed-loop power control (SSPC) algorithm and a base station assignment method based on minimizing the transmitter power (BSA-MTP) technique in a direct sequence-code division multiple access (DS-CDMA) receiver with frequency-selective Rayleigh fading. This receiver consists of three stages. In the first stage, with constrained least mean squared (CLMS) algorithm, the desired users’ signal in an arbitrary path is passed and the inter-path interference (IPI) is reduced in other paths in each RAKE finger. Also in this stage, the multiple access interference (MAI) from other users is reduced. Thus, the matched filter (MF) can use for more reduction of the IPI and MAI in each RAKE finger in the second stage. Also in the third stage, the output signals from the matched filters are combined according to the conventional maximal ratio combining (MRC) principle and then are fed into the decision circuit of the desired user. The simulation results indicate that the SSPC algorithm and the BSA-MTP technique can significantly reduce the network bit error rate (BER) compared to the other methods. Also, we observe that significant savings in total transmit power (TTP) are possible with our methods.

国际中文教育助力教育强国建设的相关思考

教育强国建设是当下中国的国家战略,国际中文教育既是整体教育的重要构成,又是助力教育强国建设的重要方面。国际中文教育之所以能提供助力,是因为它能增强国际交流与合作,提升教育国际化水平,增强国际影响力,培养国际化人才,构建全球化教育体系,参与全球教育治理。而历史事实和国际经验也提供了助力的重要依据。目前来看,国际中文教育助力教育强国建设需要在以下几个方面着力:进一步增强国际交流与合作,助力教育对外开放;讲好“三个故事”,助力中华优秀语言文化国际传播;创新国际人才教育模式,助力人才培养和双一流高校建设;发展国际中文教育数字化,助力教育数智化;完善国际中文教育规范标准体系,助力标准建设;构建国际中文教育三大体系,助力教育三大体系建设;建立全球中文教育网络系统,助力全球教育治理。

浙江新材料科创高地支撑全球先进制造业基地建设的动力机制与实现路径

新材料是浙江省“315”科技创新体系三大科创高地之一,是支撑浙江建设全球先进制造业基地着重打造的4个世界级先进产业群之一。依据浙江省建设全球新材料先进制造业基地的目标与要求,构建由新材料科创高地为基本支撑,以“政、产、学、研、用”多元创新主体协同,以“制度、技术、人才、市场、资本”多要素协同为基本动力的新材料全球先进制造业基地建设动力机制模型,并据此提出加强新材料产业集群顶层设计、支持新材料产业研发创新、完善新材料产业集群价值网络、健全专精特新小巨人企业梯度培育机制的实现路径,为新形势下浙江新材料产业发展和新材料先进制造业基地建设提供借鉴。