Energy band adjustment of 808 nm GaAs laser power converters via gradient doping

The gradient doping regions were employed in the emitter layer and the base layer of GaAs based laser power converters(LPCs).Silvaco TCAD was used to numerically simulate the linear gradient doping and exponential gradient doping structure,and analyze the transport process of photogenerated carriers.Energy band adjustment via gradient doping improved the separation and transport efficiency of photogenerated carriers and reduced the total recombination rate of GaAs LPCs.Compared with traditional structure of LPCs,the photoelectric conversion efficiency of LPCs with linear and exponential gradient doping structure were improved from 52.7%to 57.2%and 57.7%,respectively,under 808 nm laser light at the power density of 1 W/cm^(2).

1064 nm InGaAsP multi-junction laser power converters

Laser photovoltaic devices converting 1064 nm light energy into electric energy present a promising prospect in wireless energy transmission due to the commercial availability of high power 1064 nm lasers with very small divergence. Besides their high conversion efficiency, a high output voltage is also expected in a laser energy transmission system. Meanwhile,1064 nm InGaAsP multi-junction laser power converters have been developed using p^+-InGaAs/n^+-InGaAs tunnel junctions to connect sub-cells in series to obtain a high output voltage. The triple-junction laser power converter structures are grown on p-type InP substrates by metal-organic chemical vapor deposition(MOCVD), and InGaAsP laser power converters are fabricated by conventional photovoltaic device processing. The room-temperature I–V measurements show that the 1 × 1 cm^2 triplejunction InGaAsP laser power converters demonstrate a conversion efficiency of 32.6% at a power density of 1.1 W/cm^2, with an open-circuit voltage of 2.16 V and a fill factor of 0.74. In this paper, the characteristics of the laser power converters are analyzed and ways to improve the conversion efficiency are discussed.

Finite Control Set Model Predictive Control with Feedback Correction for Power Converters

As an open-loop model predictive control algorithm,finite control set model predictive control(FCS-MPC)scheme in power converter system is based on assumption that responses of optimal control implemented on prediction model agree well with actual system.The influence of model parameter mismatches and environment disturbance on control performance of scheme is neglected.Then,based on feedback correction strategy in traditional model predictive control algorithm,we derive a finite control set model predictive control with feedback correction scheme(FCS-MPCFC)that allows us to adjust prediction model output at current instant by model prediction error at previous instant,and the closed-loop correction of prediction model output is achieved.Simulations comparison analyses on a two-level three-phase inverter with multi-type model parameter mismatches controlled by traditional and improved FCS-MPC scheme are presented.Experiments are carried out on DSP controller platform.

Exact Dynamic Modeling of PWM DC-to-DC Power Converters—Part I: Continuous Conduction Mode

A general approach is presented by which the exact frequency response of any transfer function of switched linear networks can be determined. This is achieved with a describing function approach using a state space equation formulation. This work presents a somewhat simplified set of equations to one previously given by one of the authors. To demonstrate application of the general formulation, the frequency responses of switched networks used as PWM DC-to-DC converters operating in continuous conduction mode (CCM) under voltage mode control are derived. (The accompanying paper, Part II, will present results for converters operating in discontinuous conduction mode (DCM)). From the general sets of equations developed here, both the control to output and input source variation to output frequency responses are derived. The describing function approach enables exact frequency response determination, even at high frequencies where the accuracy using average models may be compromised. Confirmation of the accuracy of the derived models is provided by comparing the responses with those obtained using the commercial simulator PSIM on a PWM boost converter. The magnitude and phase responses are shown to match perfectly over the full range of frequencies up to close to half the switching frequency. Matlab code that implements the models is given such that the user can easily adapt for use with other PWM converter topologies.

Exact Dynamic Modeling of PWM DC-to-DC Power Converters—Part II: Discontinuous Conduction Mode

This paper follows on from the first paper, Part I, where a general formulation of a describing function approach to frequency response determination of switched linear networks, such as PWM converters, was simplified and updated. The models assume a piecewise linear state space equation description of the system and results in a closed form solution for the sought after frequency response. In Part I, model derivation was demonstrated for the case of PWM converters operating in the continuous conduction mode (CCM). This operating mode does not feature any state dependent switching times. In this paper, Part II, frequency response models for any transfer function for PWM converters operating in discontinuous conduction mode (DCM) are derived based on the theory presented in Part I. This operating model features state dependent switching times. The describing function models developed are exact and therefore, in terms of accuracy, are to be preferred over averaged models which are widely used. The example of a boost dc-to-dc converter operating in DCM is simulated to obtain the control to output and input to output frequency responses and are compared with the models derived here. Excellent agreement between the simulated and model responses was found. Matlab code implementing the analytical models is also presented which the user can adapt for any other PWM converter topology. The models derived here may be used as a basis from which simplified models may be derived while still preserving required accuracy.

Loop-Shaping Based Control for Switch Mode DC-DC Power Converters

Renewable energy sources require switching regulators as an interface to a load with high efficiency, small size, proper output regulation, and fast transient response. Moreover, due to the nonlinear behavior and switching nature of DC-DC power electronic converters, there is a need for high-performance control strategies. This work summarized the dynamic behavior for the three basic switch-mode DC-DC power converters operating in continuous conduction mode, i.e. buck, boost, and buck-boost. A controller was designed using loop-shaping based on current-mode control that consists of two feedback loops. A high-gain compensator with wide bandwidth was used in the inner current loop for fast transient response. A proportional-integral controller was used in the outer voltage loop for regulation purposes. A procedure was proposed for the parameters of the controller that ensures closed-loop stability and output voltage regulation. The design-oriented analysis was applied to the three basic switch-mode DC-DC power converters. Experimental results were obtained for a switching regulator with a boost converter of 150 W, which exhibits non-minimum phase behavior. The performance of the controller was tested for voltage regulation by applying large load changes.

Generic Modeling and Control Framework for Power Systems Dominated by Power Converters Connected Through a Passive Transmission and Distribution Grid

In this paper,a compact mathematical model having an elegant structure,together with a generic control framework,are proposed for generic power systems dominated by power converters that are interconnected through a passive transmission and distribution(T&D)grid,by adopting the port-Hamiltonian(pH)systems theory and the fundamental circuit theory.The models of generic T&D lines are developed and then the model of a generic T&D grid is established.With the proposed control framework,the controlled converters are proven to be passive and Input-to-State Stable(ISS).The compact mathematical model is scalable and can be applied to power systems with multiple power electronic converters with generic passive controllers,passive local loads,and different types of passive T&D lines connected in a meshed configuration without self-loops,so it is very generic.Moreover,the resulting power system is proven to be ISS as well.The analysis is carried out without assumptions on constant frequency/voltage,constant loads,and/or lossless networks,except the need of passivity for all parts involved,and without using the Clarke/Park transformations or the graph theory.To simplify the presentation,three-phase balanced systems are adopted but the results can be easily adapted for single-phase or unbalanced three-phase systems.

Application of Power Electronics Converters in Renewable Energy

Against the backdrop of global energy shortages and increasingly severe environmental pollution,renewable energy is gradually becoming a significant direction for future energy development.Power electronics converters,as the core technology for energy conversion and control,play a crucial role in enhancing the efficiency and stability of renewable energy systems.This paper explores the basic principles and functions of power electronics converters and their specific applications in photovoltaic power generation,wind power generation,and energy storage systems.Additionally,it analyzes the current innovations in high-efficiency energy conversion,multilevel conversion technology,and the application of new materials and devices.By studying these technologies,the aim is to promote the widespread application of power electronics converters in renewable energy systems and provide theoretical and technical support for achieving sustainable energy development.

Stability of interacting grid-connected power converters

The power grid in a typical micro distribution system is non-ideal,presenting itself as a voltage source with significant impedance.Thus,grid-connected converters interact with each other via the non-ideal grid.In this study,we consider the practical scenario of voltage-source converters connected to a three-phase voltage source with significant impedance.We show that stability can be compromised in the interacting converters.Specifically,the stable operating regions in selected parameter space may be reduced when grid-connected converters interact under certain conditions.In this paper,we develop bifurcation boundaries in the parameter space with respect to Hopftype instability.A small-signal model in the dq-frame is adopted to analyze the system using an impedance-based approach.Moreover,results are presented in design-oriented forms so as to facilitate the identification of variation trends of the parameter ranges that guarantee stable operation.

Circulating Current Suppression Method with Adaptive Virtual Impedance for Multi-bidirectional Power Converters Under Unbalanced Conditions

Multi-paralleled bidirectional power converters(BPCs)are commonly used to improve the power capacity and reliability in an AC/DC hybrid microgrid.However,circulating current through multi-BPCs has been one of the challenges and it can be aggravated in the presence of non-ideal operating conditions,such as unbalanced AC voltages,and the mismatch of hardware parameters.In order to suppress the circulating current,this paper proposes a distributed method based on adaptive virtual impedance,which also employs positive sequence power droop control and voltage deviation compensation control.The traditional positive sequence power droop control is adopted to only regulate the positive components of the BPCs output voltage.The negative sequence power term is fed to an adaptive virtual impedance generator to modify the damping characteristics of the BPCs.Also,an adaptive virtual impedance-based voltage deviation compensation method is proposed to recover the fluctuated output voltage of the BPCs due to droop action and the power fluctuations.The fully distributed regulation of adaptive virtual impedance enables the load power to be shared accurately among BPC modules and thus the circulating current can be effectively suppressed.The proposed control strategy does not require an additional communication system and the precise parameters of hardware equipment and line impedance.Furthermore,the effectiveness of the proposed method is verified by the experimental results.

Analysis and control of wind-driven self-excited induction generators connected to the grid through power converters

The analysis of the wind-driven self-excited induction generators （SEIGs） connected to the grid through power converters has been developed in this paper. For this analysis, a method of representing the grid power as equivalent load resistance in the steady-state equivalent circuit of SEIG has been formulated. The technique of genetic algorithm （GA） has been adopted for making the analysis of the proposed system simple and straightfor- ward. The control of SEIG is attempted by connecting an uncontrolled diode bridge rectifier （DBR） and a line commutated inverter （LCI） between the generator term- inals and three-phase utility grid. A simple control technique for maximum power point tracking （MPPT） in wind energy conversion systems （WECS）, in which the firing angle of the LCI alone needs to be controlled by sensing the rotor speed of the generator has been proposed. The effectiveness of the proposed method of MPPT and method of analysis of this wind-driven SEIG-converter system connected to the grid through power converters has been demonstrated by experiments and simulation. These experimental and simulated results confirm the usefulness and successful working of the proposed system and its analysis.

Prediction and Measurement Techniques for Radiated EMI of Power Converters with Cables

Recently,radiated electromagnetic interference(EMI)has become a research hotspot in power electronics systems,as the switching frequencies of power electronics systems have increased significantly with the adoption of wide-bandgap devices.In this article,a generalized radiated EMI model for power electronics converters with power cables is first reviewed.The radiated EMI model is then developed for a flyback power converter with critical ground impedance included.Based on the developed model,accurate high-frequency parameter extraction techniques and a radiated EMI prediction technique are developed and experimentally validated.Finally,essential measurement techniques are identified and developed to accurately extract parameters for accurate EMI prediction.The effects of the resolution bandwidth of the spectrum analyzer and critical PCB ground impedance on the radiated EMI are experimentally validated.PCB’s impact on the common-mode(CM)choke’s impedance and the radiated EMI is further validated.Techniques for minimizing the undesired near-field couplings in parameter extraction are discussed.The predicted EMI properly agreed with the measured EMI in the range of 30-230 MHz based on the EN550323 m class B standard.

Intermittency in Switching Power Converters:Theoretical Analysis

In view of reasonable explanation of intermittent subharmonics and chaos that can be gained from coupling filter between circuits,this paper discusses a method that maps time bifurcation with parameter bifurcation.Based on this mapping method,the general analysis method of characteristic multiplier,which is originally aimed at parameter bifurcation,can be used for the study of intermittency,i.e.,time bifurcation.In this paper,all researches coming from characteristic multipliers,parameter-bifurcation diagrams,and the largest Lyapunov exponent indicate the same results as those produced by simulation and experiment.Thus,it is proved theoretically that the intermittency in switching power converter can be explained in terms of coupling of spurious interference.

Analysis of Modeling the Influence of Electromagnetic Fields Radiated by Industrial Static Converters and Impacts on Operators Using Maxwell’s Equations

The study of Electromagnetic Compatibility is essential to ensure the harmonious operation of electronic equipment in a shared environment. The basic principles of Electromagnetic Compatibility focus on the ability of devices to withstand electromagnetic disturbances and not produce disturbances that could affect other systems. Imperceptible in most work situations, electromagnetic fields can, beyond certain thresholds, have effects on human health. The objective of the present article is focused on the modeling analysis of the influence of geometric parameters of industrial static converters radiated electromagnetic fields using Maxwell’s equations. To do this we used the analytical formalism for calculating the electromagnetic field emitted by a filiform conductor, to model the electromagnetic radiation of this device in the spatio-temporal domain. The interactions of electromagnetic waves with human bodies are complex and depend on several factors linked to the characteristics of the incident wave. To model these interactions, we implemented the physical laws of electromagnetic wave propagation based on Maxwell’s and bio-heat equations to obtain consistent results. These obtained models allowed us to evaluate the spatial profile of induced current and temperature of biological tissue during exposure to electromagnetic waves generated by this system. The simulation 2D results obtained from computer tools show that the temperature variation and current induced by the electromagnetic field can have a very significant influence on the life of biological tissue. The paper provides a comprehensive analysis using advanced mathematical models to evaluate the influence of electromagnetic fields. The findings have direct implications for workplace safety, potentially influencing standards and regulations concerning electromagnetic exposure in industrial settings.

Period-doubling bifurcation in two-stage power factor correction converters using the method of incremental harmonic balance and Floquet theory

In this paper, period-doubling bifurcation in a two-stage power factor correction converter is analyzed by using the method of incremental harmonic balance （IHB） and Floquet theory. A two-stage power factor correction converter typically employs a cascade configuration of a pre-regulator boost power factor correction converter with average current mode control to achieve a near unity power factor and a tightly regulated post-regulator DC-DC Buck converter with voltage feedback control to regulate the output voltage. Based on the assumption that the tightly regulated postregulator DC-DC Buck converter is represented as a constant power sink and some other assumptions, the simplified model of the two-stage power factor correction converter is derived and its approximate periodic solution is calculated by the method of IHB. And then, the stability of the system is investigated by using Floquet theory and the stable boundaries are presented on the selected parameter spaces. Finally, some experimental results are given to confirm the effectiveness of the theoretical analysis.

A review of high frequency resonant DC-DC power converters:Topologies and planar magnetic technologies

With the development of high frequency resonant DC-DC power converters,the system efficiency,power density and dynamic characteristics have been significantly improved.High frequency resonant DC-DC converters have been applied in DC grid,renewable energy,transportation,aerospace,point-of-load(POL)power supply and many other fields.Under high switching frequencies,switching loss and magnetic loss are the main concerns;thus,the resonant topology and planar magnetic are two key technologies to reduce loss.This review compares different resonant topologies and analyzes the advantages and disadvantages respectively,such as LLC circuit,dual active bridge(DAB)circuit,and other high order resonant circuits.For planar magnetic components,optimal winding structures,modeling methods and integration methods are thoroughly surveyed.With corresponding topics,the opportunities and challenges in the future development are summarized,which mainly focus on the characteristics of wide bandgap devices,such as the dynamic resistance,output capacitance loss and also the integrated module.This review can be a helpful guidance when designing high frequency resonant DC-DC converters.

A Review of Variable-inductor-based Power Converters for Eco-friendly Applications:Fundamentals,Configurations,and Applications

Modern eco-friendly industries such as renewable energy systems,electric vehicles(EVs),and light-emitting diodes(LEDs)have led to technological advancements in power electronics.Switching-based power converters have limited working ranges and can cause significant harmonics and oscillations in the output voltage and current.Introducing variable inductors can help solve this problem by changing the inductance without resorting to extreme switch duty cycles.Despite their advantages,there is still a lack of comprehensive reviews of variable inductor applications in power converter design.A thorough and in-depth review of variable inductance control in power conversion is presented,including its significance,working principle,core structure,modeling method,and typical applications.Traditionally,an inductor works in its linear magnetic region;its inductance in a power converter is considered constant,and the converter operates under fixed working conditions.However,a broad range of working conditions is required for power converters in practical applications.This is typically realized by changing the duty cycles of the switches.The working principle of variable inductance is reviewed,and the application of variable inductance control in power converters is presented,which will further help power electronics researchers and engineers design flexible and resilient power converters.

Reliability of DC-link capacitor in pulsed power supply for accelerator magnet

Capacitors are widely used in pulsed magnet power supplies to reduce ripple voltage,store energy,and decrease power variation.In this study,DC-link capacitors in pulsed power supplies were investigated.By deriving an analytical method for the capacitor current on the H-bridge topology side,the root-mean-square value of the capacitor current was calculated,which helps in selecting the DC-link capacitors.The proposed method solves this problem quickly and with high accuracy.The current reconstruction of the DC-link capacitor is proposed to avoid structural damage in the capacitor’s current measurement,and the capacitor’s hotspot temperature and temperature rise are calculated using the FFT transform.The test results showed that the error between the calculated and measured temperature increases was within 1.5℃.Finally,the lifetime of DC-link capacitors was predicted based on Monte Carlo analysis.The proposed method can evaluate the reliability of DC-link capacitors in a non-isolated switching pulsed power supply for accelerators and is also applicable to film capacitors.

Toward More Electric Powertrains in Aircraft:Technical Challenges and Advancements

The main purpose of this article is to provide an instructive review of the technological challenges hindering the road toward more electric powertrains in aircraft.Hybrid,all-electric,and turboelectric powertrain architectures are discussed as possible fuel consumption and weight reduction solutions.Among these architectures,the short-term implementation of hybrid and all-electric architectures is limited,particularly for large-capacity aircraft due to the low energy/power density levels achievable by state-of-the-art electrical energy storage systems.Conversely,turboelectric architectures with advanced distributed propulsion and boundary layer ingestion are set to lead the efforts toward more electric powertrains.At the center of this transition,power converters and high-power density electric machines,i.e.,electric motors and generators,and their corresponding thermal management systems are analyzed as the key devices enabling the more electric powertrain.Moreover,to further increase the fuel efficiency and power density of the aircraft,the benefits and challenges of implementing higher voltage powertrains are described.Lastly,based on the findings collected in this article,the projected roadmap toward more electric aircraft powertrains is presented.Herein,the individual targets for each technology,i.e.,batteries,electric machines,and power converters,and how they translate to future aircraft prototypes are illustrated.

Inductor Losses Estimation in DC-DC Converters by Means of Averaging Technique

A suitable inductor modeling for power electronic DC-DC converters is presented in this paper. It is developed with the aim of improving inductor losses estimation achievable by averaged models, which inherently neglect inductor current ripple. In order to account for its contribution to the overall inductor losses, an appropriate parallel resistance is thus enclosed into the inductor model, whose value should be chosen in accordance with the DC-DC converter operating conditions. This allows the development of improved averaged models of DC-DC converters, especially in terms of power losses estimation. The effectiveness of the proposed modeling approach has been validated through a simulation study, which refers to the case of a boost DC-DC converter and is performed by means of a suitable circuit simulator designed for rapid modelling of switching power systems （SIMetrix/SIMPLIS）.