Transition from a filamentary mode to a diffuse one with varying distance from needle to stream of an argon plasma jet

Plasma jet has extensive application potentials in various fields, which normally operates in a diffuse mode when helium is used as the working gas. However, when less expensive argon is used, the plasma jet often operates in a filamentary mode. Compared to the filamentary mode, the diffuse mode is more desirable for applications. Hence, many efforts have been exerted to accomplish the diffuse mode of the argon plasma jet. In this paper, a novel single-needle argon plasma jet is developed to obtain the diffuse mode. It is found that the plasma jet operates in the filamentary mode when the distance from the needle tip to the central line of the argon stream(d) is short. It transits to the diffuse mode with increasing d. For the diffuse mode, there is always one discharge pulse per voltage cycle, which initiates at the rising edge of the positive voltage. For comparison, the number of discharge pulse increases with an increase in the peak voltage for the filamentary mode. Fast photography reveals that the plasma plume in the filamentary mode results from a guided positive streamer,which propagates in the argon stream. However, the plume in the diffuse mode originates from a branched streamer, which propagates in the interfacial layer between the argon stream and the surrounding air. By optical emission spectroscopy,plasma parameters are investigated for the two discharge modes, which show a similar trend with increasing d. The diffuse mode has lower electron temperature, electron density, vibrational temperature, and gas temperature compared to the filamentary mode.

MODE降水检验评价指标改进及卷积半径应用

基于对象的诊断检验方法(MODE)受降水临界值、卷积半径、属性权重等参数的影响,合理选取卷积半径并准确表征预报场与观测场之间的空间相似度决定了MODE的应用效果。本文基于2020年夏季贵州54个降水个例,以多源融合降水(CMPA)作为实况,使用MODE和FSS评分(Fractions Skill Score)对中国气象局广东快速更新同化数值预报系统(CMA-GD)24 h日降水预报进行空间检验。结果表明:卷积半径过小易造成MODE提取降水对象过多,而卷积半径过大则导致局部降水信息丢失,无法从降水场中提取到降水对象。不同卷积半径下计算的最大相似度中值(M_(MI))存在突变。在M_(MI)基础上引入面积权重构造面积平均最大相似度(A_(MMI))。A_(MMI)不受提取降水对象个数的影响,较M_(MI)更具有稳定性,用于表征降水场之间的整体空间相似程度更为合理。根据对象总面积随卷积半径的变化将降水分为大范围降水和局部降水2类。大范围降水平均总面积随着卷积半径的增加而增加,A_(MMI)随卷积半径变化不大。随着卷积半径的增加,局部降水平均总面积减小,平均A_(MMI)有所减小。局部降水对卷积半径选取较为敏感,以观测场对象面积变化不超过10%的最大半径作为卷积半径有助于保留降水场大部分信息。

Control of 2-D Semi-Markov Jump Systems:A View from Mode Generation Mechanism

Dear Editor,Two-dimensional(2-D) systems have wide applications in image data processing,gas absorption and fluid dynamics analysis [1]-[3].When there exist abrupt changes in 2-D systems,they are usually modeled by 2-D Markov jump systems(MJSs) or 2-D semi-Markov jump systems(SMJSs).This letter investigates the control of 2-D SMJSs based on a novel mode generation mechanism,which could avoid mode ambiguousness phenomenon caused by the evolution of system mode in two different directions.The criterion that guarantees the almost surely exponential stability of the system is obtained.A thermal process is studied to demonstrate the availability of the proposed method.

Influences of Co-Flow and Counter-Flow Modes of Reactant Flow Arrangement on a PEMFC at Start-Up

To investigate the influences of co-flowand counter-flowmodes of reactant flowarrangement on a proton exchange membrane fuel cell(PEMFC)during start-up,unsteady physical and mathematical models fully coupling the flow,heat,and electrochemical reactions in a PEMFC are established.The continuity equation and momentum equation are solved by handling pressure-velocity coupling using the SIMPLE algorithm.The electrochemical reaction rates in the catalyst layers(CLs)of the cathode and anode are calculated using the Butler-Volmer equation.The multiphase mixture model describes the multiphase transport process of gas mixtures and liquid water in the fuel cell.After validation,the influences of co-flow and counter-flow modes on the PEMFC performance are investigated,including the evolution of the current density,flow field,temperature field,and reactant concentration field during start-up,as well as the steady distribution of the current density,reactant concentration,andmembrane water content when the start-up stabilizes.Co-flow and counter-flow modes influence the current density distribution and temperature distribution.On the one hand,the co-flow mode accelerates the start-up process of the PEMFC and leads to a more evenly distributed current density than the counter-flow mode.On the other hand,the temperature difference between the inlet and outlet sections of the cell is up to 10.1℃ under the co-flow mode,much larger than the 5.0℃ observed in the counter-flow mode.Accordingly,the counter-flowmode results in a more evenly distributed temperature and a lower maximum temperature than the co-flow case.Therefore,in the flow field design of a PEMFC,the reactant flow arrangements can be considered to weigh between better heat management and higher current density distribution of the cell.

Investigation on the roles of equilibrium toroidal rotation during edge-localized mode mitigated by resonant magnetic perturbations

The effects of equilibrium toroidal rotation during edge-localized mode(ELM)mitigated by resonant magnetic perturbation(RMP)are studied with the experimental equilibria of the EAST tokamak based on the four-field model in the BOUT++code.As the two main parameters to determine the toroidal rotation profiles,the rotation shear and magnitudes were separately scanned to investigate their roles in the impact of RMPs on peeling-ballooning(P-B)modes.On one hand,the results show that strong toroidal rotation shear is favorable for the enhancement of the self-generated E×B shearing rate<ω_(E×B)>with RMPs,leading to significant ELM mitigation with RMP in the stronger toroidal rotation shear region.On the other hand,toroidal rotation magnitudes may affect ELM mitigation by changing the penetration of the RMPs,more precisely the resonant components.RMPs can lead to a reduction in the pedestal energy loss by enhancing the multimode coupling in the turbulence transport phase.The shielding effects on RMPs increase with the toroidal rotation magnitude,leading to the enhancement of the multimode coupling with RMPs to be significantly weakened.Hence,the reduction in pedestal energy loss by RMPs decreased with the rotation magnitude.In brief,the results show that toroidal rotation plays a dual role in ELM mitigation with RMP by changing the shielding effects of plasma by rotation magnitude and affecting<ω_(E×B)>by rotation shear.In the high toroidal rotation region,toroidal rotation shear is usually strong and hence plays a dominant role in the influence of RMP on P-B modes,whereas in the low rotation region,toroidal rotation shear is weak and has negligible impact on P-B modes,and the rotation magnitude plays a dominant role in the influence of RMPs on the P-B modes by changing the field penetration.Therefore,the dual role of toroidal rotation leads to stronger ELM mitigation with RMP,which may be achieved both in the low toroidal rotation region and the relatively high rotation region that has strong rotational shear.

On the generation of high-quality Nyquist pulses in mode-locked fiber lasers

Nyquist pulses have wide applications in many areas,from electronics to optics.Mode-locked lasers are ideal platforms to generate such pulses.However,how to generate high-quality Nyquist pulses in mode-locked lasers remains elusive.We address this problem by managing different physical effects in mode-locked fiber lasers through extensive numerical simulations.We find that net dispersion,linear loss,gain and filter shaping can affect the quality of Nyquist pulses significantly.We also demonstrate that Nyquist pulses experience similariton shaping due to the nonlinear attractor effect in the gain medium.Our work may contribute to the design of Nyquist pulse sources and enrich the understanding of pulse shaping dynamics in mode-locked lasers.

Effects of diamagnetic drift on nonlinear interaction between multi-helicity neoclassical tearing modes

A numerical study of the diamagnetic drift effect on the nonlinear interaction between multi-helicity neoclassical tearing modes(NTMs) is carried out using a set of four-field equations including two-fluid effects.The results show that,in contrast to the single-fluid case,5/3 NTM cannot be completely suppressed by 3/2 NTM with diamagnetic drift flow.Both modes exhibit oscillation and coexist in the saturated phase.To better understand the effect of the diamagnetic drift flow on multiple-helicity NTMs,the influence of typical relevant parameters is investigated.It is found that the average saturated magnetic island width increases with increasing bootstrap current fraction f_(b) but decreases with the ion skin depth δ.In addition,as the ratio of parallel to perpendicular transport coefficients χ_(‖)/χ_(⊥) increases,the average saturated magnetic island widths of the 3/2 and 5/3 NTMs increase.The underlying mechanisms behind these observations are discussed in detail.

Constraint on the focal mechanism of the 2011 Tohoku earthquake from the radial modes

Different from other normal modes of the Earth’s free oscillation that depend on all the six components(M_(rr),M_(tt),M_(pp),M_(rt),M_(rp),and M_(tp))of the centroid moment tensor,the amplitudes of the radial modes depend on the M_(rr)component(e.g.,scalar moment(M_(0)),dip(δ),and slip(λ))and hypocenter depth of the focal mechanism,and hence can be easily used to constrain these parameters of the focal mechanism.In this study,we use the superconducting gravimeter(SG)records after the 2011 Tohoku earthquake to analyze the radial modes_(0)S_(0)and_(1)S_(0).Based on the solutions of the focal mechanism provided by the GCMT and USGS,we can obtain the theoretical amplitudes of these two radial modes.Comparing the theoretical amplitudes with the observation amplitudes,it is found that there are obvious differences between the former and the latter,which means that the GCMT and USGS focal mechanisms cannot well represent the real focal mechanism of the 2011 event.Taking the GCMT solution as a reference and changing the depth and the three parameters of the M_(rr)moment,the scalar moment(M_(0))and the dip(δ)have significant influences,but the effects of the slip(λ)and the depth are minor.After comparisons,we provide a new constraint(M_(0)=5.8±0.09×10^(22)N·m,δ=10.1±0.08°,λ=88°,and depth=20 km)for the focal mechanism of the 2011 event.In addition,we further determine the center frequency(1.631567±2.6e^(-6)mHz)and quality factor(2046.4±50.1)of the_(1)S_(0)mode.

Observation of Doppler shift f_(D) modulated by the internal kink mode using conventional reflectometry in the EAST tokamak

In this paper we present a new experimental observation using a conventional reflectometry technique,poloidal correlation reflectometry(PCR),in the Experimental Advanced Superconducting Tokamak(EAST).The turbulence spectrum detected by the PCR system exhibits an asymmetry and induced Doppler shift f_(D)during the internal kink mode(IKM)rotation phase.This Doppler shift f_(D)is the target measurement of Doppler reflectometry,but captured by conventional reflectometry.Results show that the Doppler shift f_(D)is modulated by the periodic changes in the effective angle between the probing wave and cutoff layer normal,but not by plasma turbulence.The fishbone mode and saturated long-lived mode are typical IKMs,and this modulation phenomenon is observed in both cases.Moreover,the value of the Doppler shift f_(D)is positively correlated with the amplitude of the IKM,even when the latter is small.However,the positive and negative frequency components of the Doppler shift f_(D)can be asymmetric,which is related to the plasma configuration.A simulated analysis is performed by ray tracing to verify these observations.These results establish a clear link between f_(D)and IKM rotation,and are helpful for studying the characteristics of IKM and related physical phenomena.

Generation of lossy mode resonances(LMR)using perovskite nanofilms

The results presented here show for the first time the experimental demonstration of the fabrication of lossy mode resonance(LMR) devices based on perovskite coatings deposited on planar waveguides. Perovskite thin films have been obtained by means of the spin coating technique and their presence was confirmed by ellipsometry, scanning electron microscopy, and X-ray diffraction testing. The LMRs can be generated in a wide wavelength range and the experimental results agree with the theoretical simulations. Overall, this study highlights the potential of perovskite thin films for the development of novel LMR-based devices that can be used for environmental monitoring, industrial sensing, and gas detection, among other applications.

Coupling of quasi-localized and phonon modes in glasses at low frequency

Boson peak of glasses,a THz vibrational excess compared to Debye squared-frequency law,remains mysterious in condensed-matter physics and material science.It appears in many different kinds of glassy matters and is also argued to exist in damped crystals.A consensus is that boson peak originates from the coupling of the(quasi)-localized non-phonon modes and the plane-wave-like phonon modes,but the coupling behavior is still not fully understood.In this paper,by modulating the content of localized modes and the frequencies of phonon modes,the coupling is clearly reflected in the localization and anharmonicity of low-frequency vibrational modes.The coupling enhances with increasing cooling rate and sample size.For finite sample size,phonon modes do not fully intrude into the low frequency to form a dense spectrum and they are not sufficiently coupled to the localized modes,thus there is no Debye level and boson peak is ill-defined.This suggestion remains valid in the presence of thermal motions induced by temperature,even though the anharmonicity comes into play.Our results point to the coupling of quasi-localized and phonon modes and its relation to the boson peak.

Phase-locked single-mode terahertz quantum cascade lasers array

We demonstrated a scheme of phase-locked terahertz quantum cascade lasers(THz QCLs)array,with a single-mode pulse power of 108 mW at 13 K.The device utilizes a Talbot cavity to achieve phase locking among five ridge lasers with first-order buried distributed feedback(DFB)grating,resulting in nearly five times amplification of the single-mode power.Due to the optimum length of Talbot cavity depends on wavelength,the combination of Talbot cavity with the DFB grating leads to better power amplification than the combination with multimode Fabry-Perot(F-P)cavities.The Talbot cavity facet reflects light back to the ridge array direction and achieves self-imaging in the array,enabling phase-locked operation of ridges.We set the spacing between adjacent elements to be 220μm,much larger than the free-space wavelength,ensuring the operation of the fundamental supermode throughout the laser's dynamic range and obtaining a high-brightness far-field distribution.This scheme provides a new approach for enhancing the single-mode power of THz QCLs.

Fully spin-polarized, valley-polarized and spin-valley-polarized electron beam splitters utilizing zero-line modes in a three-terminal device

Topological zero-line modes(ZLMs) with spin and valley degrees of freedom give rise to spin, valley and spinvalley transport, which support a platform for exploring quantum transport physics and potential applications in spintronic/valleytronic devices. In this work, we investigate the beam-splitting behaviors of the charge current due to the ZLMs in a three-terminal system. We show that with certain combinations of ZLMs, the incident charge current along the interface between different topological phases can be divided into different polarized currents with unit transmittance in two outgoing terminals. As a result, fully spin-polarized, valley-polarized and spin-valley-polarized electron beam splitters are generated. The mechanism of these splitters is attributed to the cooperative effects of the distribution of the ZLMs and the intervalley and intravalley scatterings that are modulated by the wave-vector mismatch and group velocity mismatch. Interestingly, half-quantized transmittance of these scatterings is found in a fully spin-valley-polarized electron beam splitter.Furthermore, the results indicate that these splitters can be applicable to graphene, silicene, germanene and stanene due to their robustness against the spin–orbit coupling. Our findings offer a new way to understand the transport mechanism and investigate the promising applications of ZLMs.

Robust optical mode converter based on topological waveguide arrays

Optical mode converters are essential for enhancing the capacity of optical communication systems. However, fabrication errors restrict the further improvement of conventional mode converters. To address this challenge, we have designed an on-chip TE0–TE1mode converter based on topologically protected waveguide arrays. The simulation results demonstrate that the converter exhibits a mode coupling efficiency of 93.5% near 1550 nm and can tolerate a relative fabrication error of 30%. Our design approach can be extended to enhance the robustness for other integrated photonic devices, beneficial for future development of optical network systems.

Topological laser on square lattice with gain–loss-induced higher-order corner modes

We investigate the higher-order topological laser in the two-dimensional(2D) coupled-cavity array. By adding staggered on-site gain and loss to the 2D Hermitian array with a trivial phase, the system will emerge degenerate topological corner modes, which are protected by bulk band gap. For such a non-Hermitian model, by adjusting the parameters of the system and introducing the pumping into the cavity at the corner, a single-mode lasing with topological protection emerges.Furthermore, single-mode lasing exists over a wide range of pumping strengths. No matter where the cavity is initially stimulated, after enough time evolution, all the cavities belonging to the topological corner mode can emit a stable laser.

A Novel Disturbance Observer Based Fixed-Time Sliding Mode Control for Robotic Manipulators With Global Fast Convergence

This paper proposes a new global fixed-time sliding mode control strategy for the trajectory tracking control of uncertain robotic manipulators.First,a fixed-time disturbance observer(FTDO) is designed to deal with the adverse effects of model uncertainties and external disturbances in the manipulator systems.Then an adaptive scheme is used and the adaptive FTDO(AFTDO) is developed,so that the priori knowledge of the lumped disturbance is not required.Further,a new non-singular fast terminal sliding mode(NFTSM) surface is designed by using an arctan function,which helps to overcome the singularity problem and enhance the robustness of the system.Based on the estimation of the lumped disturbance by the AFTDO,a fixed-time non-singular fast terminal sliding mode controller(FTNFTSMC)is developed to guarantee the trajectory tracking errors converge to zero within a fixed time.The settling time is independent of the initial state of the system.In addition,the stability of the AFTDO and FTNFTSMC is strictly proved by using Lyapunov method.Finally,the fixed-time NFESM(FTNFTSM) algorithm is validated on a 2-link manipulator and comparisons with other existing sliding mode controllers(SMCs) are performed.The comparative results confirm that the FTNFTSMC has superior control performance.

Energy evolution and structural health monitoring of coal under different failure modes:An experimental study

Structural instability in underground engineering,especially in coal-rock structures,poses significant safety risks.Thus,the development of an accurate monitoring method for the health of coal-rock bodies is crucial.The focus of this work is on understanding energy evolution patterns in coal-rock bodies under complex conditions by using shear,splitting,and uniaxial compression tests.We examine the changes in energy parameters during various loading stages and the effects of various failure modes,resulting in an innovative energy dissipation-based health evaluation technique for coal.Key results show that coal bodies go through transitions between strain hardening and softening mechanisms during loading,indicated by fluctuations in elastic energy and dissipation energy density.For tensile failure,the energy profile of coal shows a pattern of “high dissipation and low accumulation” before peak stress.On the other hand,shear failure is described by “high accumulation and low dissipation” in energy trends.Different failure modes correlate with an accelerated increase in the dissipation energy before destabilization,and a significant positive correlation is present between the energy dissipation rate and the stress state of the coal samples.A novel mathematical and statistical approach is developed,establishing a dissipation energy anomaly index,W,which categorizes the structural health of coal into different danger levels.This method provides a quantitative standard for early warning systems and is adaptable for monitoring structural health in complex underground engineering environments,contributing to the development of structural health monitoring technology.

Factors Influencing Mode of Delivery: A Case-Control Study

The primary objective of this investigation was to scrutinize the prepregnancy conditions and lifestyles of 2046 women residing in Liuzhou City, with the aim of delineating the determinants of delivery methods. Evidently, the study unearthed substantial correlations between prepregnancy body mass index, educational attainment, exposure to passive smoking, medical history, and other variables with the mode of delivery. Furthermore, a predictive nomogram model was formulated to accurately forecast the likelihood of cesarean section. These discernments equip pertinent authorities with the means to institute targeted screening and supportive measures for women contemplating pregnancy based on these identified factors. Moreover, provision of services such as prepregnancy counseling and clinical risk assessments could be instrumental in curbing the incidence of cesarean section.

Electroencephalogram Signal Correlations between Default Mode Network and Attentional Functioning

Attentional issues may affect acquiring new information, task performance, and learning. Cortical network activities change during different functional brain states, including the default mode network (DMN) and attention network. We investigated the neural mechanisms underlying attentional functions and correlations between DMN connectivity and attentional function using the Trail-Making Test (TMT)-A and -B. Electroencephalography recordings were performed by placing 19 scalp electrodes per the 10 - 20 system. The mean power level was calculated for each rest and task condition. Non-parametric Spearman’s rank correlation was used to examine the correlation in power levels between the rest and TMT conditions. The most significant correlations during TMT-A were observed in the high gamma wave, followed by theta and beta waves, indicating that most correlations were in the parietal lobe, followed by the frontal, central, and temporal lobes. The most significant correlations during TMT-B were observed in the beta wave, followed by the high and low gamma waves, indicating that most correlations were in the temporal lobe, followed by the parietal, frontal, and central lobes. Frontoparietal beta and gamma waves in the DMN may represent attentional functions.

Fault Identification for Shear-Type Structures Using Low-Frequency Vibration Modes

Shear-type structures are common structural forms in industrial and civil buildings,such as concrete and steel frame structures.Fault diagnosis of shear-type structures is an important topic to ensure the normal use of structures.The main drawback of existing damage assessment methods is that they require accurate structural finite element models for damage assessment.However,for many shear-type structures,it is difficult to obtain accurate FEM.In order to avoid finite elementmodeling,amodel-freemethod for diagnosing shear structure defects is developed in this paper.This method only needs to measure a few low-order vibration modes of the structure.The proposed defect diagnosis method is divided into two stages.In the first stage,the location of defects in the structure is determined based on the difference between the virtual displacements derived from the dynamic flexibility matrices before and after damage.In the second stage,damage severity is evaluated based on an improved frequency sensitivity equation.Themain innovations of this method lie in two aspects.The first innovation is the development of a virtual displacement difference method for determining the location of damage in the shear structure.The second is to improve the existing frequency sensitivity equation to calculate the damage degree without constructing the finite elementmodel.Thismethod has been verified on a numerical example of a 22-story shear frame structure and an experimental example of a three-story steel shear structure.Based on numerical analysis and experimental data validation,it is shown that this method only needs to use the low-order modes of structural vibration to diagnose the defect location and damage degree,and does not require finite element modeling.The proposed method should be a very simple and practical defect diagnosis technique in engineering practice.