Experiments on rockburst proneness of pre-heated granite at different temperatures: Insights from energy storage, dissipation and surplus

Many underground engineering projects show that rockburst can occur in rocks at great depth and high temperature, and temperature is a critical factor affecting the intensity of rockburst. In general, temperature can affect the energy storage, dissipation, and surplus in rock. To explore the influence of temperature on the energy storage and dissipation characteristics and rockburst proneness, the present study has carried out a range of the uniaxial compression(UC) and single-cyclic loading-unloading uniaxial compression(SCLUC) tests on pre-heated granite specimens at 20℃-700℃. The results demonstrate that the rockburst proneness of pre-heated granite initially increases and subsequently decreases with the increase of temperature. The temperature of 300℃ has been found to be the threshold for rockburst proneness. Meanwhile, it is found that the elastic strain energy density increases linearly with the total input strain energy density for the pre-heated granites, confirming that the linear energy property of granite has not been altered by temperature. According to this inherent property, the peak elastic strain energy of pre-heated granites can be calculated accurately. On this basis, utilising the residual elastic energy index, the rockburst proneness of pre-heated granite can be determined quantitatively. The obtained results from high to low are: 317.9 k J/m^(3)(300℃), 264.1 k J/m^(3)(100℃), 260.6 k J/m^(3)(20℃), 235.5 k J/m^(3)(500℃), 158.9 k J/m^(3)(700℃), which are consistent with the intensity of actual rockburst for specimens. In addition, the relationship between temperature and energy storage capacity(ESC) of granite was discussed, revealing that high temperature impairs ESC of rocks, which is essential for reducing the rockburst proneness. This study provides some new insights into the rockburst proneness evaluation in high-temperature rock engineering.

Pre-heating temperature induced flowability and wax deposition characteristics of crude oil adding wax inhibitors

This paper investigated the effects of pre-heating treatment temperatures(T_(pre))on the flowability and wax deposition characteristics of a typical waxy crude oil after adding wax inhibitors.It is found that there is little difference in wax precipitation exothermic characteristics of crude oils at different T_(pre),as well as the wax crystal solubility coefficient in the temperature range of 25-30℃.For the undoped crude oil,the flowability after wax precipitation gets much improved and the wax deposition is alleviated as T_(pre)increasing.At T_(pre)=50℃,the viscosity and wax deposition rate of crude oil adding wax inhibitors are higher than those of the undoped crude oil.When the T_(pre)increases to 60,70,and 80℃,the flowability of the doped crude oil are largely improved and the wax deposition is suppressed with the T_(pre)increase,but the wax content of wax deposit increases gradually.It is speculated that,on the one hand,the T_(pre)increase helps the dispersion of asphaltenes into smaller sizes,which facilitates the co-crystallization with paraffin waxes and generates more aggregated wax crystal flocs.This weakens the low-temperature gel structure and increases the solid concentration required for the crosslink to form the wax deposit.On the other hand,the decrease in viscosity increases the diffusion rate of wax molecules and accelerates the aging of wax deposits.The experimental results have important guiding significance for the pipeline transportation of doped crude oils.

Effect of Conduction Pre-heating in Au-Al Thermosonic Wire Bonding

This paper presents the recent study by investigating the vital responses of wire bonding with the application of conduction pre-heating. It is observed through literature reviews that, the effect of pre-heating has not been completely explored to enable the successful application of pre-heating during wire bonding. The aim of wire bonding is to form quality and reliable solid-state bonds to interconnect metals such as gold wires to metalized pads deposited on silicon integrated circuits. Typically, there are 3 main wire bonding techniques applied in the industry;Thermo-compression, Ultrasonic and Thermosonic. This experiment utilizes the most common and widely used platform which is thermosonic bonding. This technique is explored with the application of conduction pre-heating along with heat on the bonding site, ultrasonic energy and force on an Au-Al system. Sixteen groups of bonding conditions which include eight hundred data points of shear strength at various temperature settings were compared to establish the relationship between bonding strength and the application of conduction pre-heating. The results of this study will clearly indicate the effects of applied conduction pre-heating towards bonding strength which may further produce a robust wire bonding system.

Effect of Pre-heating Temperature on Structural and Optical Properties of Sol-gel Derived Zn_(0.8)Cd_(0.2)O Thin Films

Zn_（0.8）Cd_（0.2）O thin films prepared using the spin-coating method were investigated. X-ray diffraction, scanning electron microscopy, and UV-Vis spectrophotometry were employed to illustrate the effects of the pre-heating temperature on the crystalline structure, surface morphology and transmission spectra of Zn_（0.8）Cd_（0.2）O thin films. When the thin films were pre-heated at 150 ℃, polycrystalline Zn O thin films were obtained. When the thin films were pre-heated at temperatures of 200 ℃ or higher, preferential growth of Zn O nanocrystals along the c-axis was observed. Transmission spectra showed that thin films with high transmission in the visible light range were prepared and effective bandgap energies of these thin films decreased from 3.19 e V to 3.08 e V when the pre-heating temperature increased from 150 ℃ to 300 ℃.

Implementation of Pre-Heating System in Stenters for Improving Machine Performance and Increasing Efficiency

In textile finishing, stenters always draw considerable attention to newer inventions to boost up production via maximum utilization of energy. Prior to main drying or heat-setting chambers, intermediate heating of cylindrical system especially by steam has a direct blessing to moisture evaporation, processing speed, fabric quality and so on. Based on actual operational data, this study reveals the outcomes of a pre-heating module installed within a stenter. After employing the pre-heating system to knit fabrics of different structures and compositions, 23% - 61% moisture reduction was found and the speed of processing fabrics was increased simultaneously by 17% - 30% without any compromise on fabric quality. Moreover, no less than 8.21% savings in annual electricity consumption were observed.

Characterization of mechanical and corrosion properties of cryorolled Al 1100 alloy:Effect of annealing and solution treatment

Effect of annealing and solution treatment prior to cryorolling on the formation of initial structure influencing microstructure formation from nano to micron scale and resultant mechanical and corrosion properties in Al 1100 alloy has been studied in detail.Before subjecting to 50%cryorolling,samples were pre-annealed at 250℃ for 2 h and pre-solution treated at 540℃ for 1 h.X-ray diffraction and HRTEM techniques were used to understand the crystallite size,lattice strain and dislocation configuration in the processed alloy.The results indicate that the pre-annealed sample has the highest grain aspect ratio(4.43),the smallest crystallite size(37.53 nm),the highest lattice strain(9.12×10^(−3))and the highest dislocation density(45.16×10^(13) m^(−2))among the tested sample.The pre-annealed sample shows a significant improvement of 43.44%,24.64%and 20.33%in hardness,ultimate tensile strength and yield strength.Both pre-annealed and pre-solution treated samples show improved corrosion resistance when compared to cryorolled samples without any pre-treatment,with the pre-annealed sample showing the best corrosion resistance.

Effect of Y_2O_3 stabilized ZrO_2 coating with tri-model structure on bi-layered thermally grown oxide evolution in nano thermal barrier coating systems at elevated temperatures

Bi-layered thermally grown oxide （TGO） layer plays a major role in the spallation of Y2O3 stabilized ZrO2 （YSZ） layer form the bond coat in the thermal barrier coating （TBC） systems during oxidation. On the other hand, bi-layered TGO formation and growth in the TBC systems with nanostructured YSZ have not been deeply investigated during cyclic oxidation. Hence, Inconel 738/NiCrAlY/normal YSZ and Inconel 738/NiCrAlY/nano YSZ systems were pre-oxidized at 1000 °C and then subjected to cyclic oxidation at 1150 °C. According to microstructural observations, nanostructured YSZ layer over the bond coat should have less mi-cro-cracks and pinholes, due to the compactness of the nanostructure and the presence of nano zones that resulted in lower O infiltration into the nanothermal barrier coating system, formation of thinner and nearly continuous mono-layered thermally grown oxide on the bond coat during pre-oxidation, lower spinels formation at the Al2O3/YSZ interface and finally, reduction of bi-layered thermally grown oxide thickness during cyclic oxidation. It was found that pre-heat treatment and particularly coating microstructure could influence microstructural evolution （bi-layered TGO thickness） and durability of thermal barrier coating systems during cyclic oxidation.

Experimental study on the partial preheating combustion characteristic of Yankuang coal sludge

Coal sludge is a seriously polluted solid waste,and the rational utilization of its resources has long being an undoubtedly important research topic.This paper mainly studies the coal sludge partial preheating characteristic,combustion characteristic and the process of migration and conversion of nitrogen with preheating combustion technology.The experimental results indicate that most of the elements in the coal sludge are released during preheating,and the ratio of the fuel-N converted to the N_(2),NH_(3) and HCN are 75.5%,6.74%and 0.64%,respectively.Compared with the coal sludge,the BET surface area and cumulative pore area of preheated char are increased.The surface of preheated char is loose and porous with many fine particles,while raw coal is dense with larger particles.Meantime,the quantity of carbon defect structure,the active sites and the reactivity of preheated char are all increased.In the whole process,the NO_(x) emission is about 156 mg/m3(@6%O2),the ratio of fuel-N converted to NO_(x) was 2.98%,and the combustion efficiency is 96.5%.This experiment results will play a vital role in efficient and clean utilization of coal sludge.