Intraocular pressure and gonioscopic findings in primary angle-closure disease in India—a big data study

AIM:To describe the gonioscopic profile and intraocular pressure(IOP)in primary angle-closure(PAC)disease in patients presenting to a tertiary eye care network in India.METHODS:A cross-sectional hospital-based study that included 31484 new patients presenting between 2011 and 2021.Patients with a clinical diagnosis of PAC/suspect/glaucoma were included.The data was collected from an electronic medical record system.RESULTS:PAC glaucoma(PACG)(47.55%)was the most common diagnosis followed by PAC(39.49%)and PAC suspect(PACS;12.96%).Female preponderance(54.6%)was noted with higher mean age at presentation among males(P<0.0001).PACS and PAC showed the highest prevalence in 6th decade but PACG was higher at 7th decade.The probability of angle opening was 95.93%,90.32%and 63.36%in PACS,PAC and PACG eyes respectively post peripheral iridotomy(PI).Plateau iris syndrome(PIS)was noted in 252 eyes and all showed post dilated rise of IOP.A post dilated IOP rise was also noted with 8.86%,33.95%and 57.19%eyes with PACS,PAC and PACG respectively with IOP rise between 6-8 mm Hg across the disease spectrum.CONCLUSION:The superior quadrant is the narrowest angle and difficult to open with indentation and post PI.The probability of angle opening is less in PIS especially the complete variety along with post dilated IOP rise.The post dilated IOP rise in angle closure eyes warrants a careful dilatation,especially with PIS.

Survey-Based Analysis of Water Consumption Law in High-Rise Public Buildings and Water-Saving Performance of Pressure-Reducing Measures

Facing the contradiction of water scarcity and water wastage in most cities of China, this study aims at probing into the factors influencing water-use efficiency and assessing water-saving potential by adopting pressure control measures based on field survey conducted in 23 high-rise buildings in Suqian, China and laboratory tests. Results showed that per capita water consumption (PCWC) exceeding water consumption norms is common in these buildings. The hourly water consumption variation law is quite different among different types of buildings. These differences should be considered in designing building water supply systems to lower water and energy consumption. On the basis of correlation analysis, the order of factors influencing the PCWC follows average tap water pressure, percapita building area, and building age, suggesting pressure management in high-rise buildings is a key water-saving measure. Field tests of outflow characteristics under different water pressures indicated that over-pressure outflow (OPO) is a common cause of water wastage in buildings, however, no branch pipe pressure control measures were found in all the surveyed buildings. Laboratory tests showed that branch pipe pressure-reducing measures can lower water consumption and improve the comfortability of use as well. Therefore, in addition to applying high efficiency water-saving devices, we strongly recommend that branch pipe pressure-reducing measures should be strictly implemented in designing new building water supply systems and reconstruction of existing old building water supply systems, thereby, promoting water, energy saving and development of green building.

Pore-scale study of the pressure-sensitive effect of sandstone and its influence on multiphase flows

The pressure-sensitive effect on the pore structure of sandstone was investigated using X-ray computed micro-tomography and QEMSCAN quantitative mineral analysis. In a physical simulation study, we extracted the pore network model from digital cores at different confining pressures and evaluated the effect of pressure sensitivity on the multiphase displacement process. In both the pore network model and QEMSCAN scanning, the pore structure was observed to be damaged under a high confining pressure. Due to their different scales, the pores and throats exhibited inhomogeneous changes; further, the throats exhibited a significant variation compared to that exhibited by the pores. Meanwhile, the heterogeneity of the pore structure under the two aforementioned activities was aggravated by the elastic-plastic deformation of the pore structure.The pressure-sensitive effect increased the proportion of mineral particles, such as quartz(the main component of the core skeleton), and reduced the proportion of clay minerals. The clay minerals were originally attached to the pore walls or interspersed in the pores; however, as the pressure increased, the clay minerals accumulated in the pores resulting in blockage of the pores. While simulating the multiphase displacement process, increasing the confining pressure was observed to severely restrict the flowability of oil and water. This study promises to improve the efficiency of reservoir development in terms of oil and gas exploitation.

Effect of pulse voltage rising time on discharge characteristics of a helium-air plasma at atmospheric pressure

In this paper,the influence of voltage rising time on a pulsed-dc helium-air plasma at atmospheric pressure is numerically simulated.Simulation results show that as the voltage rising time increases from 10 ns to 30 ns,there is a decrease in the discharge current,namely 0.052 A when the voltage rising time is 10 ns and 0.038 A when the voltage rising time is 30 ns.Additionally,a shorter voltage rising time results in a faster breakdown,a more rapidly rising current waveform,and a higher breakdown voltage.Furthermore,the basic parameters of the streamer discharge also increase with voltage rise rate,which is ascribed to the fact that more energetic electrons are produced in a shorter voltage rising time.Therefore,a pulsed-dc voltage with a short rising time is desirable for efficient production of nonequilibrium atmospheric pressure plasma discharge.

Comparison of electrochemical properties of atmospheric pressure plasma coatings for Al_2O_3-3TiO_2 and CoNiCrAlY in sea water

To improve the durability of underwater rotating products,the corrosion characteristics in harsh marine environment were evaluated through various electrochemical experiments on the Al2O3-3TiO2 and CoNiCrAlY coating layers by atmospheric pressure plasma spray coating process.By evaluating the corrosion resistance of these materials,their applicability to environmentally friendly power generation equipment such as blades of tidal current turbines was examined.According to the Tafel analysis for micro-areas including the coating layer,the coating/metal interlayer and the base metal,the Al2O3-3TiO2 coating layer and the CoNiCrAlY coating layer show markedly lower corrosion current density than the base metal.The corrosion current density of the CoNiCrAlY coating layer (9.75316×10-8A/cm2) is about 1.6 times more than that of the Al2O3-3TiO2 coating layer (6.13139×10-8A/cm2).

Development of the Separate Air-Supply Type of Pressurization Smoke Control System for the Stairwells of High-Rise Buildings in Korea

The pressurization smoke control system has been commonly used as a smoke control system at the emergency stairs of high-rise buildings. However, a higher possibility of overpressure between the lobby and the accommodation or pressure drop in the lobby could lead to failure in achievement of the purpose of pressurization system, particularly when supplying the leakage and supplementary air flow through one air-supply path at a time. To improve this particular issue, the devise configurations, as well as the different ways to supply the leakage and supplementary air flow through the different flow passages have been proposed. The performance of the trial product was evaluated on the test bed, ultimately providing a safe evacuation environment if high-rise buildings fired.

Comparative Study of Magmatism in East Pacific Rise Versus Nearby Seamounts:Constraints on Magma Supply and Thermal Structure Beneath Mid-ocean Ridge

Major elements of 2202 basalts from the East Pacific Rise （EPR） and 888 basalts from near- EPR seamounts are used to investigate their differences in magma crystallization pressures and mantle melting conditions. Crystallization pressure calculation from basalts with 5.0wt%〈MgO〈8.0wt % shows that magma crystallization pressures beneath near-EPR seamounts are positively and negatively correlated with Nas and Fes, respectively. However, these correlations are indistinct in axial lavas, which can be explained by chemical homogenization induced by extensive mixing processes. In each segment divided by major transforms and over-lapping spreading centers （OSCs）, near-EPR seamount lavas have higher magma crystallization pressures, higher Fes and lower Nas than the EPR lavas, which indicate cooler lithosphere, lower degrees and shallower melting depths beneath near-EPR seamounts than the EPR. The correlations between magma crystallization pressures and melting conditions beneath near-EPR seamounts imply that the source thermal state controls the melting degree and melt flux, and then melting process controls the shallow lithosphere temperature and magma crystallization depth （pressure）. The cooler mantle sources beneath near-EPR seamounts produce a lower degree of melting and a less robust magma supply, which results in a deep thermal equilibrium level and high magma crystallization pressure. The magma crystallization pressure decreases significantly as spreading rate of the EPR increases from ~80 mm/year in the north （16~N） to ~160 mm/year in the south （19~S）, while this trend is unobvious in near-EPR seamounts. This suggests that the magma supply controlled by spreading rate dominates the ridge crust temperature and magma crystallization depth, while the near-EPR seamount magma supply is not dominated by the axial spreading rate. Because most seamounts form and gain most of their volume within a narrow zone of 5-15 km from ridge axis, they provide good constraint on magma supply and thermal structure beneath the EPR. High magma crystallization pressures in seamounts indicate dramatic temperature decrease from the EPR. The crystallization pressures of seamount lavas are well correlated with mantle melting parameters but in a blurry relationship with axial spreading rate. Despite the adjacency of the EPR and nearby seamounts, the thermal structure beneath the near-EPR seamounts are controlled by their own magma supply and conductive cooling, chemically and thermally unaffected by magmatism beneath the ridge axis.

Effect of particle size of coal dust on explosion pressure

The effect of the particle size of coal dust on explosion pressure and the rising rate of explosion pressure is studied. Three coal dusts from Lingan Coal Mine in Canada and Datong Coal Mine in China are selected to test. The influence of particle size on the maximum explosion pressure P max and maximum pressure rising rate (d p /d t ) max of each coal dust was tested experimentally. The results indicate that with the decrease of particle size of coal dusts, explosion pressure increases on condition of the same concentration. If the concentration of coal dust is different, the maximum explosion pressure appears at the concentration of 500 g/m^3. The smaller the particle size of coal dusts, the larger the rising rate of explosion pressure of coal dust. When the concentration of coal dust is 500 g/m^3, the rising rate of explosion pressure of each coal dust is the maximum.

THE CENTRAL DISTRIBUTION OF ADRENOMEDULLIN AND ITS EFFECTS ON BLOOD PRESSURE AND HEART RATE IN RATS

The present study was designed to make certain whether there exists adrenomedullin (ADM) in the rat central nervous system and evaluated the hemodynamic actions of intracerebroventricular administration (ICVA) of human ADM[13-52]. By immunohistochemistry (ABC method),We found that there was a discrete localization of ADM-positive immunoreactivity in the rat central system including cerebral cortex,paraventricular tissues, hypothalamus, cerebella cortex, mesencephalon and medulla oblongata. By reverse transcription-polymerase chain reaction(RT-PCR) analysis, rat ADM mRNA was found to be expressed in rat brain. These above results of immunohistochemistry and RT-PCR suggest that ADM exists in the rat brain. We also found that centrally administered ADM[13-52]in a dose of 0.4 to 3. 2 nmol/kg provoked marked, prolonged and dosedependent increases in mean arterial blood pressure (MABP) and heart rate (HR). To clarify the mechanisms of the hemodynamic changes induced by centrally administered ADM [13-52]. the effect of centrally administered ADM [13-52] on renal sympathetic nerve activity (RSNA) was studied. The result showed that centrally administered ADM [13-52] ( 1. 6 nmol/kg) provoked a marked increase in RSNA .therefore .the increases in MABP and HR induced by centrally administered ADM [13-52]might be due to the stimulation of central sympathetic mechanism. In addtion,we also compared the relationship of activity and structure among the different fragments of ADM. In conclusion, ADMexists in the rat brain, and it may play an important role in the central control of cardiovascular system.

Diffusion coefficients of natural gas in foamy oil systems under high pressures

The diffusion coefficient of natural gas in foamy oil is one of the key parameters to evaluate the feasibility of gas injection for enhanced oil recovery in foamy oil reservoirs. In this paper, a PVT cell was used to measure diffusion coefficients of natural gas in Venezuela foamy oil at high pressures, and a new method for deter- mining the diffusion coefficient in the foamy oil was de- veloped on the basis of experimental data. The effects of pressure and the types of the liquid phase on the diffusion coefficient of the natural gas were discussed. The results indicate that the diffusion coefficients of natural gas in foamy oil, saturated oil, and dead oil increase linearly with increasing pressure. The diffusion coefficient of natural gas in the foamy oil at 20 MPa was 2.93 times larger than that at 8.65 MPa. The diffusion coefficient of the natural gas in dead oil was 3.02 and 4.02 times than that of the natural gas in saturated oil and foamy oil when the pressure was 20 MPa. However, the gas content of foamy oil was 16.9 times higher than that of dead oil when the dissolution time and pressure were 20 MPa and 35.22 h, respectively.

Dynamic calibration method of capacitive pressure measuring device

This paper presents working principle,structure and a dynamic calibration method of capacitive pressure measuring device.Using this method,placing calibrated capacitive electronic pressure measuring device and three standard sensors in simulation chamber pressure generator is proper and the data generated by them are analyzed and compared.This calibration method realizes dynamic calibration of capacitive electronic pressure measuring device under actual working pressure;pressure signal and frequency spectrum are analyzed.The experimental results show that simulation chamber pressure calibration method is feasible.

Experimental analysis of pressure characteristics of catalyst powder flowing down a cyclone dipleg

An experiment was carried out for investigating pressure behavior of catalyst powders, with a Sauter mean diameter of 63.6 μm, flowing downward in a cyclone dipleg with 150 mm inner diameter and 9000 mm high. Time mean pressure and time series of pressure fluctua- tions were measured at different axial positions in the dipleg with particle mass fluxes ranging from 50.0 to 385.0 kg m-2s t. The experimental results showed that the time mean pressure in the dipleg increased progres- sively from the top section to the bottom section. The experimental phenomena displayed that the fluidization patterns in the dipleg can be divided into two types on the whole, namely the dilute-dense coexisting falling flow and the dense conveying flow along the dipleg. In the dilute- dense coexisting falling flow, the dilute phase region was composed of a length of swirling flow below the inlet of dipleg and a dilute falling flow above the dense bed level. With increasing particle mass flux, the dilute-dense coex- isting falling flow was gradually transformed to be the dense conveying flow, and the exit pressure of the dipleg increased considerably. The pressure fluctuations were closely related to the flnidization patterns inside the dipleg. In the dilute-dense coexisting falling flow, the pressure fluctuations in the dilute flow region originated from par- ticle clusters, propagating downward as a pressure wave; however, the pressure fluctuations in the dense flow region originated from rising gas bubbles, propagating upward. When the dense conveying flow was formed in the dipleg,the pressure fluctuations originated mainly from instability of the feed and the compressed gas, propagating down- ward. The standard deviation of the pressure fluctuations indicated that the intensity of pressure fluctuations first increased and then decreased with increasing particle flux.

Research on New Testing Method and Instrument of Clothing Pressure

This paper discusses the formation of the fabric clothingpressure,the efforts of the human body and the impor-tance of the clothing pressure measurement.Several as-pects such as setting up the scientific and simple measur-ing method of the clothing pressure,the designing andmaking the measuring instruments are emphasized.Bymeans of experimental testing and analysis,some usefulresults can be derived from these works.

Modeling of fluid dynamics interacting with ductile fraction propagation in high pressure pipeline

This paper presents a computational model for the fluid dynamics in a fractured ductile pipe under high pressure. The pressure profile in front of the crack tip, which is the driving source of crack propagation, is computed using a nonlinear wave equation. The solution is coupled with a one dimensional choked flow analysis behind the crack. The simulation utilizes a high order optimized prefactored compact-finite volume method in space, and low dispersion and dissipation Runge-Kutta in time. As the pipe fractures the rapid depressurization take place inside the pipe and the propagation of the crack-induced waves strongly influences the outflow dynamics. Consistent with the experimental observation, the model predicts the expansion wave inside the pipe, and the reflection and outflow of the wave. The model also helps characterize the propagation of the crack dynamics and fluid flows around the tip of the crack.

Formation permeability evaluation and productivity prediction based on mobility from pressure measurement while drilling

Based on the measurement mechanism of mobility in pressure measurement while drilling, through analyzing a large number of mobility data, it is found that under the condition of water-based mud drilling, the product of mobility from pressure measurement while drilling and the viscosity of mud filtrate is infinitely close to the water phase permeability under the residual oil in relative permeability experiment. Based on this, a method converting the mobility from pressure measurement while drilling to core permeability is proposed, and the permeability based on Timur formula has been established. Application of this method in Penglai 19-9 oilfield of Bohai Sea shows:(1) Compared with the permeability calculated by the model of adjacent oilfields, the permeability calculated by this model is more consistent with the permeability calculated by core analysis.(2) Based on the new model, the correlation between the calculated mobility of well logging and the actual drilling specific productivity index bas been established. Compared with the relationship established by using the permeability model of an adjacent oilfield, the correlation of the new model is better.(3) Productivity of four directional wells was predicted, and the prediction results are in good agreement with the actual production after drilling.

基于k-均值聚类算法的高层建筑表面风压分区研究

为分析高层建筑表面的风压特征和关键区域,以高宽比为4∶1的高层建筑风洞试验模型为对象,采用k-均值聚类算法,对0°风向角下模型各个面的风压测压管时程数据进行分析,研究结果表明:建筑左、右侧面以强烈的负压为主导,且角点附近存在负压极值;k-均值聚类算法可以有效地识别不同表面风压场的特征,风压的聚类结果与平均风压系数的分布较为吻合,且能得到代表性的风压测压管。

超细氢氧化镁粉体抑制甲烷-空气混合物爆炸效能研究

为研究绿色阻燃剂——氢氧化镁（Mg（OH）2）粉体对甲烷爆炸的抑制效能，采用20L近球形爆炸罐系统，通过试验考察Mg（OH）2粉体对甲烷爆炸压力的降低幅度，得到最佳抑爆粉体浓度。试验中粉体质量浓度按50g／m^3幅度增加，同一组试验做3次。试验结果表明，Mg（OH）2粉体在一定程度上可以抑制甲烷爆炸威力，且粒径为0．085和1．3μm时，对同一浓度的甲烷气体最佳抑爆粉体浓度相同。平均粒径为0．085和1．3μm的Mg（OH）2粉体，可使甲烷体积分数为7．0％的甲烷-空气混合气体的爆炸压力分别下降13．48％和10．92％，这时的最佳抑爆粉体质量浓度为175～225g／m^3；可使体积分数为9．5％的甲烷气体的爆炸压力分别下降25．42％和19．48％，这时的最佳抑爆粉体质量浓度为225～275g／m^3。

浓度梯度对甲烷-空气混合气体爆炸特性参数的影响

为研究浓度梯度的变化对甲烷-空气预混气燃爆特性的影响。在方形爆炸实验管道中布置压力、温度传感器,开展不同甲烷浓度梯度下甲烷-空气预混气体爆炸试验。研究结果表明:浓度梯度的增大使管道内甲烷-空气预混气的火焰平均速度和最大爆炸压力均呈现先升高后降低的趋势,当浓度梯度为1.0%时二者均达到最大值;爆炸压力上升速率亦随浓度梯度增大先升高后降低,浓度梯度为1.5%时最大;达到最大爆炸压力的时间随浓度梯度的增加呈现往复变化趋势;甲烷-空气混合气的爆炸温度随浓度梯度的上升呈现先上升后下降的趋势。

初始温度对甲烷-空气爆炸压力影响的试验研究

借助特殊环境20 L爆炸特性测试系统,研究了初始温度对甲烷-空气爆炸压力的影响,初始压力为0.1 MPa,初始温度变化范围为298～473 K。结果表明,甲烷-空气爆炸的最大爆炸压力随初始温度的升高而降低,初始温度由298 K升高到473 K,最大爆炸压力由0.7833 MPa下降到0.5012 MPa,下降幅度为35.89％。初始温度的升高加快了反应速率,缩短了最大爆炸压力到达时间,由298 K时的127.1 ms缩短到473 K时的85.0 ms。初始温度升高,甲烷-空气最大爆炸压力的上升速率（ dp/dt） max呈上升趋势。当初始温度由298 K上升至473 K时,（ dp/dt） max升幅并不大,仅为9.16％；爆炸特征值KG 不断增大,其爆炸危险性也随之增大。从反应开始到到达最大爆炸压力这段时间内,爆炸压力上升速率的变化在一定程度上可以反映甲烷-空气爆炸反应速率的变化情况。

引燃柴油喷油正时对LNG-柴油双燃料发动机燃烧特性的影响

以一台涡轮增压六缸柴油机改造的发动机为试验对象,研究引燃柴油喷油正时对LNG-柴油双燃料发动机燃烧特性的影响。研究了不同喷油正时下的双燃料发动机的缸内压力、压力升高率、缸内温度、燃烧放热规律、循环变动等参数。研究结果表明:引燃柴油喷油正时对双燃料发动机燃烧特性影响很大。随引燃柴油喷油正时的增大,最高缸内压力、最高压力升高率、最大燃烧温度和最大瞬时放热率先升高后降低且所对应的曲轴转角减小;峰值压力循环变动系数先降低后增大,峰值压力升高率循环变动系数降低。