Controlling mine pressure by subjecting high-level hard rock strata to ground fracturing

When mining extra-thick coal seams,the main cause of strong ground pressure are the high-level thick and hard strata,but as yet there is no active and effective control technology.This paper proposes the method of subjecting hard roofs to ground fracturing,and physical simulation is used to study the control effect of ground fracturing on the strata structure and energy release.The results show that ground fracturing changes the structural characteristics of the strata and reduces the energy release intensity and the spatial extent of overburden movement,thereby exerting significant control on the ground pressure.The Datong mining area in China is selected as the engineering background.An engineering test was conducted on site by ground horizontal well fracturing,and a 20-m-thick hard rock layer located 110 m vertically above the coal seam was targeted as the fracturing layer.On-site microseismic monitoring shows that the crack propagation length is up to 216 m and the height is up to 50 m.On-site mine pressure monitoring shows that(1)the roadway deformation is reduced to 100 mm,(2)the periodic weighting characteristics of the hydraulic supports are not obvious,and(3)the ground pressure in the working face is controlled significantly,thereby showing that the ground fracturing is successful.Ground fracturing changed the breaking characteristics of the high-level hard strata,thereby helping to ameliorate the stress concentration in the stope and providing an effective control approach for hard rock.

Blood Pressure Profile and Glycemic Control of Type 2 Diabetics and Hypertensives at the Yalgado Ouedraogo University Hospital: A Review of 116 Cases

Objective: The association hypertension and diabetes is important. The two pathologies may influence each other. The aim was to study the correlation between glycemic control and blood pressure control and to determine the factors associated with blood pressure control. Methodology: This was a descriptive cross-sectional study with an analytical focus over 7 months. Patients were recruited as outpatients and all underwent ambulatory blood pressure measure, glycated hemoglobin and creatinine measurements, and assessment of compliance with treatment. Results: During this period 116 patients were collected. The predominance was female 69%. The mean age of the patients was 62 ± 7 years with a peak between 60 and 70 years. The average age of hypertension was 12 years and that of diabetes 6 1/2 years. The most frequently associated cardiovascular risk factor was a sedentary lifestyle (71.5%) after age. 57.8% of patients were not controlled at the office, with a predominance of systolic hypertension (58.2%). 61.6% of patients were controlled by ambulatory blood pressure measure, a rate of 47.8% of white coat hypertension. Glycemic control was observed in 42.2% of cases and 87% of patients had good renal function (glomerular filter rate ≥ 60 ml/mn). Therapeutic compliance was good in 53.4% of cases and dual therapy was the most used therapeutic modality 44.8% (52 patients) followed by triple therapy. The factors associated with poor blood pressure control were glycemic imbalance, non-compliance and monotherapy. Dual therapy had a protective effect. Conclusion: The association of hypertension and type 2 diabetes is frequent. The risk of occurrence increases with age. Ambulatory blood pressure measure is the best method to assess blood pressure control. Optimization of blood pressure control should also include optimization of glycemic control.

Synthetic analysis of meteorological elements for the sea fogs occurred in northwest the Yellow Sea under low pressure control and comparison with sea fogs occurred under high pressure control in summer

Based on the principle of transient perturbation analysis,in this paper,a method to objectively determine the weather pattern formed by sea fog is provided.On the basis of the classification results,the circulation situation,divergence and vertical velocity field,and the vertical profile of temperature and humidity are synthesized and analyzed.The basic characteristics of the circulation and physical field of sea fog under low pressure control(L type sea fog)are obtained,and the results are compared with the sea fog under the control of high pressure(H type sea fog):a)L type sea fogs potential height anomaly disturbance is mainly manifested in the low layer,and its average value is-65.66 gpm,gradually weakening upward;b)L type sea fogs inversion structure is weaker than H type sea fogs when it occurs,the fog layer is thicker and the high relative humidity level is high over the fog layer,while the H type sea fogs fog layer has a relatively obvious dry layer;c)L sea fog has three layers of structure at the vertical direction.The first layer 1000-950 hPa is convergence accompanied by weak rise and subsidence,the second layer 950-850 hPa is divergence accompanied by weak subsidence,and the third layer 850 to 500hPa is gradually strengthened.While there are two layer structures of the H type sea fog.1000 hPa is divergence accompanied by weak rising and sinking movement,950-500 hPa is a uniform subsidence movement.d)Probability density statistical analysis further quantified the vertical movement of L and H type sea fog and the distribution of relative humidity in each layer.These conclusions provide an important reference for forecasting the sea fog in the northwest of the Yellow Sea under the condition of low pressure circulation in summer.

A Fuzzy Logic Based Supervisory Hierarchical Control Scheme for Real Time Pressure Control

This paper describes a supervisory hierarchical fuzzy controller （SHFC） for regulating pressure in a real-time pilot pressure control system. The input scaling factor tuning of a direct expert controller is made using the error and process input parameters in a closed loop system in order to obtain better controller performance for set-point change and load disturbances. This on-line tuning method reduces operator involvement and enhances the controller performance to a wide operating range. The hierarchical control scheme consists of an intelligent upper level supervisory fuzzy controller and a lower level direct fuzzy controller. The upper level controller provides a mechanism to the main goal of the system and the lower level controller delivers the solutions to a particular situation. The control algorithm for the proposed scheme has been developed and tested using an ARM7 microcontroller-based embedded target board for a nonlinear pressure process having dead time. To demonstrate the effectiveness, the results of the proposed hierarchical controller, fuzzy controller and conventional proportional-integral （PI） controller are analyzed. The results prove that the SHFC performance is better in terms of stability and robustness than the conventional control methods.

In-situ pressure-preserved coring for deep exploration:Insight into the rotation behavior of the valve cover of a pressure controller

In-situ pressure-preserved coring(IPP-Coring)is considered to be the most reliable and efficient method for the identification of the scale of oil and gas resources.During IPP-Coring,because the rotation behavior of the pressure controller valve cover in different medium environments is unclear,interference between the valve cover and inner pipe may occur and negatively affect the IPP-Coring success rate.To address this issue,we conducted a series of indoor experiments employing a high-speed camera to gain greater insights into the valve cover rotation behavior in different medium environments,e.g.,air,water,and simulated drilling fluids.The results indicated that the variation in the valve cover rotation angle in the air and fluid environments can be described by a one-phase exponential decay function with a constant time parameter and by biphasic dose response function,respectively.The rotation behavior in the fluid environments exhibited distinct elastic and gravitational acceleration zones.In the fluid environments,the density clearly impacted the valve cover closing time and rotation behavior,whereas the effect of viscosity was very slight.This can be attributed to the negligible influence of the fluid viscosity on the drag coefficient found in this study;meanwhile,the density can increase the buoyancy and the time period during which the valve cover experienced a high drag coefficient.Considering these results,control schemes for the valve cover rotation behavior during IPP-Coring were proposed for different layers and geological conditions in which the different drilling fluids should be used,e.g.,the use of a high-density valve cover in high-pore pressure layers.

Asymmetric Fuzzy Control of a Positive and Negative Pneumatic Pressure Servo System

The pneumatic pressure control systems have been used in some fields. However, the researches on pneumatic pressure control mainly focus on constant pressure regulation. Poor dynamic characteristics and strong nonlinearity of such systems limit its application in the field of pressure tracking control. In order to meet the demand of generating dynamic pressure signal in the application of the hardware-in-the-loop simulation of aerospace engineering, a positive and negative pneumatic pressure servo system is provided to implement dynamic adjustment of sealed chamber pressure. A mathematical model is established with simulation and experiment being implemented afterwards to discuss the characteristics of the system, which shows serious asymmetry in the process of charging and discharging. Based on the analysis of the system dynamics, a fuzzy proportional integral derivative （PID） controller with asymmetric fuzzy compensator is proposed. Different from conventional adjusting mecha- nisms employing the error and change in error of the controlled variable as input parameters, the current cham- ber pressure and charging or discharging state are chosen as inputs of the compensator, which improves adaptability. To verify the effectiveness and performance of the pro- posed controller, the comparison experiments tracking sinusoidal and square wave commands are conducted. Experimental results show that the proposed controller can obtain better dynamic performance and relatively consis- tent control performance across the scope of work （2-140 kPa）. The research proposes a fuzzy control method to overcome asymmetry and enhance adaptability for the positive and negative pneumatic pressure servo system.

Simulation and Experiment Research on the Proportional Pressure Control of Water-assisted Injection Molding

Water-assisted injection molding（WAIM）,a newly developed fluid-assisted injection molding technology has drawn more and more attentions for the energy saving,short cooling circle time and high quality of products.Existing research for the process of WAIM has shown that the pressure control of the injecting water is mostly important for the WAIM.However,the proportional pressure control for the WAIM system is quite complex due to the existence of nonlinearities in the water hydraulic system.In order to achieve better pressure control performance of the injecting water to meet the requirements of the WAIM,the proportional pressure control of the WAIM system is investigated both numerically and experimentally.A newly designed water hydraulic system for WAIM is first modeled in AMEsim environment,the load characteristics and the nonlinearities of water hydraulic system are both considered,then the main factors affecting the injecting pressure and load flow rate are extensively studied.Meanwhile,an open-loop model-based compensation control strategy is employed to regulate the water injection pressure and a feedback proportional integrator controller is further adopted to achieve better control performance.In order to verify the AMEsim simulation results WAIM experiment for particular Acrylonitrile Butadiene Styrene（ABS） parts is implemented and the measured experimental data including injecting pressure and flow rate results are compared with the simulation.The good coincidence between experiment and simulation shows that the AMEsim model is accurate,and the tracking performance of the load pressure indicates that the proposed control strategy is effective for the proportional pressure control of the nonlinear WAIM system.The proposed proportional pressure control strategy and the conclusions drawn from simulation and experiment contribute to the application of water hydraulic proportional control and WAIM technology.

Design and Experimental Evaluation of PID Controller for Digital Electro-Pneumatic Cabin Pressure Control System

The performance of the designed digital electro-pneumatic cabin pressure control system for the cabin pressure schedule of transport aircraft is investigated.For the purpose of this study,an experimental setup consisting of a simulated hermetic cabin and altitude simulation chamber is configured for cabin pressure control system operation.A series of experimental tests are executed to evaluate the performance of the cabin pressure control system.The parameters of the PID controller are optimized.In the optimization process,the variation regularity of the rate of cabin pressure change under various conditions is considered.An approach to prioritize the control of the rate of change of cabin pressure based on the flight status model is proposed and verified experimentally.The experimental results indicate that the proposed approach can be adopted for the designed digital electro-pneumatic cabin pressure control system to obtain a better cabin pressure schedule and rate of cabin pressure change.

Clinical application of flexible ureteroscopic sheath with controllable intraluminal pressure in treating ureteral stones

Objective:The purpose of the study was to assess the clinical efficacy and safety of a combined perfusion suction platform with pressure feedback control function and an ureteroscopic suction sheath that can measure the ureteropelvic pressure in implementing lithotripsies.Methods:Fifty-two patients who underwent lithotripsy under intelligent monitoring of ureteral intraluminal pressure from June 2016 to January 2018 were retrospectively recruited.The inclusion standard was stone diameter>1.5 cm but<2.5 cm.After the 12/14 Fr suction sheath was placed,manometer interface and suction interface of the sheath were connected to the platform via the pressure sensor and suction tube,respectively.The ureteroscope was connected to the platform perfusion pump,and the crushed stones were aspirated out under negative pressure.Results:According to the location of the stone,21(40.4%)cases were classified as upper ureteral stones,19(36.5%)were midureteral stones,and 12(23.1%)were lower ureteral stones.Forty-seven patients underwent successful primary sheath placement and lithotripsy with a mean operative time of 34.5(standard deviation 18.3)min.Retrograde stone migration did not occur.There were eight patients with hematuria postoperatively.Serious complication was 1.9% with one case of ureteral perforation.Stone clearance was 95.7% at Day 1e2 postoperatively,and 100% at Day 30 postoperatively.Conclusion:Ureteroscopic lithotripsy with intelligent pressure control using our device improved the efficiency of the lithotripsy and rate of stone clearance.The safety of the operation can be ensured.It is worth popularization and application in clinical practice.

Design of the pressure regulation algorithm for active braking in vehicle ACC system

To develop the pressure control algorithm for active braking of adaptive cruise control（ACC） system,a test bench with real parts of the tested vehicle is built.With the dynamic analysis of the active braking actuators,it is demonstrated that different duty of pulse-width modulation（PWM） signals could control the pressure changing rate of the wheel cylinder.To obtain that signal,a modified proportional-integral-differential（PID） control algorithm is developed using the variable parameter method,the control value reset method,the dead zone method and the integral saturation method.Experimental results show that the delay and overshoot of the pressure response could be reduced considerably using the modified PID algorithm compared with the conventional one.The proposed pressure control algorithm could be used for the further development of the ACC＇s controller.

Rotational failure analysis of spherical-cylindrical shell pressure controllers related to gas hydrate drilling investigations

In situ pressure-preserved coring(IPP-Coring)technology is considered one of the most efficient methods for assessing resources.However,seal failure caused by the rotation of pressure controllers greatly affects the success of pressure coring.In this paper,a novel spherical-cylindrical shell pressure controller was proposed.The finite element analysis model was used to analyze the stress distribution and deformation characteristics of the pressure controller at different rotation angles.The seal failure mechanism caused by the rotation of the pressure controller was discussed.The stress deviation rate was defined to quantitatively characterize the stress concentration.Based on the test equipment designed in this laboratory,the ultimate bearing strength of the pressure controller was tested.The results show that the rotation of the valve cover causes an increase in the deformation on its lower side.Furthermore,the specific sealing pressure in the weak zone is greatly reduced by a statistically significant amount,resulting in seal failure.When the valve cover rotates 5°around the major axis,the stress deviation rate is-92.6%.To prevent rotating failure of the pressure controller,it is necessary to control the rotation angle of the valve cover within 1°around the major axis.The results of this research can help engineers reduce failure-related accidents,provide countermeasures for pressure coring,and contribute to the exploration and evaluation of deep oil and gas resources.

Pressurization control system for low pressure crucible casting

A new compact pressurization control system of the low pressure casting machine for crucible pressure casting has been developed. It is especially designed for the production of high-quality aluminum or magnesium alloy parts with low input cost. This machine with such a system has the virtue of economical and compact, and combines the Fuzzy-PID technology and achieves accuracies of ±2.5 mbar. At present, this machine has been adopted by several users in China for the production of aluminum alloy castings with high property requirements. Furthermore, for magnesium alloy castings, this machine can be used with the gas protect unit.

Pressure control strategy for pump motor energy transfer unit

Multi-level pressure source system is a novel hydraulic system with distinct advantage of energy saving. In order to balance each pressure level of the multi-level pressure source system, a pump motor energy transfer unit is usually equipped. However, the pump motor energy transfer has the characteristics of poor starting and low response, which cause long time of pressure adjustment and large pressure jitter when the transformer is switched to system suddenly and the motor-side pressure has pressure impact when rail of the pump-side is switched. To address these problems, this paper proposes a compound control strategy of feedforward compensation control with Fuzzy-PID to improve the controllability of the multi-level pressure source system. A test rig of the pump motor energy transfer unit is built and the controllability of compound controller and PID controller are compared. The experiment results show that, compared with the traditional PID, the adjustment time and the pressure impact are reduced by 20% and 25% with the proposed compound control strategy. Therefore, the presented compound control strategy can be used to improve starting performance and robustness of the pump motor energy transfer unit control system.

Pressure Regulation for Earth Pressure Balance Control on Shield Tunneling Machine by Using Adaptive Robust Control

Most current studies about shield tunneling machine focus on the construction safety and tunnel structure stability during the excavation. Behaviors of the machine itself are also studied, like some tracking control of the machine. Yet, few works concern about the hydraulic components, especially the pressure and flow rate regulation components. This research focuses on pressure control strategies by using proportional pressure relief valve, which is widely applied on typical shield tunneling machines. Modeling of a commercial pressure relief valve is done. The modeling centers on the main valve, because the dynamic performance is determined by the main valve. To validate such modeling, a frequency-experiment result of the pressure relief valve, whose bandwidth is about 3 Hz, is presented as comparison. The modeling and the frequency experimental result show that it is reasonable to regard the pressure relief valve as a second-order system with two low corner frequencies. PID control, dead band compensation control and adaptive robust control（ARC） are proposed and simulation results are presented. For the ARC, implements by using first order approximation and second order approximation are presented. The simulation results show that the second order approximation implement with ARC can track 4 Hz sine signal very well, and the two ARC simulation errors are within 0.2 MPa. Finally, experiment results of dead band compensation control and adaptive robust control are given. The results show that dead band compensation had about 30° phase lag and about 20% off of the amplitude attenuation. ARC is tracking with little phase lag and almost no amplitude attenuation. In this research, ARC has been tested on a pressure relief valve. It is able to improve the valve＇s dynamic performances greatly, and it is capable of the pressure control of shield machine excavation.

Effect of Home Blood Pressure Telemonitoring Plus Additional Support on Blood Pressure Control:A Randomized Clinical Trial

Objective Current clinical evidence on the effects of home blood pressure telemonitoring(HBPT)on improving blood pressure control comes entirely from developed countries.Thus,we performed this randomized controlled trial to evaluate whether HBPT plus support(patient education and clinician remote hypertension management)improves blood pressure control more than usual care(UC)in the Chinese population.Methods This single-center,randomized controlled study was conducted in Beijing,China.Patients aged 30-75 years were eligible for enrolment if they had blood pressure[systolic(SBP)≥140 mmHg and/or diastolic(DBP)≥90 mmHg;or SBP≥130 mmHg and/or DBP≥80 mmHg with diabetes].We recruited 190 patients randomized to either the HBPT or the UC groups for 12 weeks.The primary endpoints were blood pressure reduction and the proportion of patients achieving the target blood pressure.Results Totally,172 patients completed the study,the HBPT plus support group(n=84),and the UC group(n=88).Patients in the plus support group showed a greater reduction in mean ambulatory blood pressure than those in the UC group.The plus support group had a significantly higher proportion of patients who achieved the target blood pressure and maintained a dipper blood pressure pattern at the12th week of follow-up.Additionally,the patients in the plus support group showed lower blood pressure variability and higher drug adherence than those in the UC group.Conclusion HBPT plus additional support results in greater blood pressure reduction,better blood pressure control,a higher proportion of dipper blood pressure patterns,lower blood pressure variability,and higher drug adherence than UC.The development of telemedicine may be the cornerstone of hypertension management in primary care.

Modeling the pressure characteristics of parallel chokes used in managed pressure drilling and related experiments

Based on the local resistance computation model for a choke valve and using the flow characteristics of choke valves, we studied the relationships between the back pressure of a parallel choke assembly and the opening extent of choke valves and developed a model to characterize the pressure regime of the manifold assembly. A comparison of pressure characteristic curves shows that a parallel choke manifold assembly has obvious advantages over the conventional serial type including high linearity of pressure-regulating characteristics curves, the elimination of the overshoot interval, wider effective regulating interval and the higher system security. Laboratory hydraulic experiments have validated the capability of a back pressure control model for the parallel choke assembly to accurately control pressure. This study is of great theoretical and practical significance to further improve the performance of chokes used in managed pressure well drilling.

Temperature Compensation Algorithm for Hydraulic System Pressure Control

In this paper the control mechanism of solenoid valve is analyzed,which shows the solenoid valve control is actually the control of coil current.The response characteristic of coil current is related to coil inductance and resistance.The coil resistance is influenced greatly by the ambient temperature and the self-heating of coil,which affects the control precision of coil current.First,considering the heat dissipation mode of coil,the coil temperature model is established from the perspective of heat conduction,and a temperature compensation algorithm for hydraulic system pressure control is put forward.Then the hardware-in-the-loop testbed is set up by using the dSPACE platform,carrying out wheel cylinder pressurization tests with inlet valve fully opened at-40℃ and 20℃,and testing the actual pressure of wheel cylinder with the target pressures at-40℃ and 6 000 kPa/s(pressurization rate).The results show that the pressure control temperature compensation algorithm proposed in this paper accurately corrects the influence of resistance temperature drift on the response accuracy of wheel cylinder pressure.After the correction,the pressure difference is less than 500 kPa,which can meet the control accuracy requirements of solenoid valve,enriching the linear control characteristic of solenoid valve.

Novel miniature pneumatic pressure regulator for hopping robots

A novel miniature pressure regulator is fabricated and studied. The regulator can easily be integrated into portable mechatronics or miniature robotic applications because of its lightweight and compact size. An especial poppet is designed to minimize its size and to withstand high-pressure. The pressure regulator is designed for a hopping robot which is powered by a combustion system. The hopping robot has great moving capacities such as jumping over big obstacles, wails and dit- ches. The regulator helps the hopping robot to decrease size and weight, and to sustain high pres- sure of oxygen and fuel tank. It will maintain constant output pressure to obtain suitable proportion of oxygen and fuel in the combustion cylinder. Dynamic simulation of the miniature pneumatic pres- sure regulator is performed. Experiments on prototype of miniature pneumatic pressure regulator are also carried out to validate the performance and satisfied performance is obtained.

Application of adaptive fuzzy control technology to pressure control of a pressurizer

A pressurizer is one of important equipment in a pressurized water reactor plant. It is used to maintain the pressure of primary coolant within allowed range because the sharp change of coolant pressure affects the security of reactor, therefor, the study of pressurizer’s pressure control methods is very important. In this paper, an adaptive fuzzy controller is presented for pressure control of a presurizer in a nuclear power plant. The controller can on-line tune fuzzy control rules and parameters by self-learning in the actual control process, which possesses the way of thinking like human to make a decision. The simulation results for a pressurized water reactor plant show that the adaptive fuzzy controller has optimum and intelligent characteristics, which prove the controller is effective.

Automated postoperative blood pressure control

It is very important to maintain the level of mean arterial pressure （MAP）. The MAP control is applied in many clinical situations, including limiting bleeding during cardiac surgery and promoting healing for patient＇ s post-surgery. This paper presents a fuzzy controller-based multiple-model adaptive control system for postoperative blood pressure management. Multiple-model adaptive control （MMAC） algorithm is used to identify the patient model, and it is a feasible system identification method even in the presence of large noise. Fuzzy control （FC） method is used to design controller bank. Each fuzzy controller in the controller bank is in fact a nonlinear proportional-integral （PI） controller,whose proportional gain and integral gain are adjusted continuously according to error and rate of change of error of the plant output, resulting in better dynamic and stable control performance than the regular PI controller, especially when a nonlinear process is involved. For demonstration, a nonlinear, pulsatile-flow patient model is used for simulation, and the results show that the adaptive control system can effectively handle the changes in patient＇s dynamics and provide satisfactory performance in regulation of blood pressure of hypertension patients.