Recovery and regeneration of LiFePO_(4)from spent lithium-ion batteries via a novel pretreatment process

The recycling of spent LiFePO_(4)batteries has received extensive attention due to its environmental impact and economic benefit.In the pretreatment process of spent LiFePO_(4)batteries,the separation of active materials and current collectors determines the difficulty of the re-covery process and product quality.In this work,a facile and efficient pretreatment process is first proposed.After only freezing the electrode pieces and immersing them in boiling water,LiFePO_(4)materials were peeled from the Al foil.Then,after roasting under an inert atmosphere and sieving,all the cathode and anode active materials were easily and efficiently separated from the Al and Cu foils.The active materials were subjected to acid leaching,and the leaching solution was further used to prepare FePO_(4)and Li_(2)CO_(3).Finally,the battery-grade FePO_(4)and Li_(2)CO_(3)were used to re-synthesize LiFePO_(4)/C via the carbon thermal reduction method.The discharge capacities of re-synthesized LiFePO_(4)/C cathode were 144.2,139.0,133.2,125.5,and 110.5 mA·h·g−1 at rates of 0.1,0.5,1,2,and 5 C,which satisfies the requirement for middle-end LiFePO_(4)batteries.The whole process is environmental and has great potential for industrial-scale recycling of spent lithium-ion batteries.

Pretreatment of super viscous oil wastewater and its application in refinery

Wastewater from super viscous oil processing cannot be effectively treated by conventional wastewater treatment plants in refineries because of its high concentration of various organic pollutants. In order to resolve this problem, a number of investigations were conducted in our work to understand the physicochemical properties, sedimentation, demulsification and pretreatment of such super viscous oil refinery wastewater. The results showed that the key issues for pretreatment of this wastewater were： （1） Optimized process parameters were used in the sedimentation and demulsification processes for oil removal to effectively recover oil and remove scum from wastewater; （2） A suitable flocculation process was selected to minimize oil, suspended solids （SS） and chemical oxygen demand （CODcr）. A pretreatment process including three continuous steps： oil removal by sedimentation, oil removal by demulsification, and flotation separation, was proposed and applied in Liaohe Petrochemical Company, PetroChina and the oil content in effluents was less than 200 mg/L and CODcr less than 2,500 mg/L, which completely met the requirement for influent of the conventional wastewater treatment plant, and the recovered super viscous oil reached 5,873 tons in the initial year in Liaohe Petrochemical Company, PetroChina.

Influence of texture pretreatment on cold rolling texture of ELC-BH sheet

In order to further investigate how cold rolling texture is produced in an extra low-carbon and high strengthbake-hardening sheet steel (for short, hereafter, coiled ELC-BH sheet) with r value as high as 2.67, texture change intexture pretreatment and its effects on the cold rolling texture are researched by means of Orientation Distribution Funchon (ODf) method. Experimental results show that the cold rolling texture which Produces very strong {111 } annealing texture actually is caused by texture change in the texture pretreatment, and the strong {111 } texture obtainedrough this texture pretreatment is an essential condition of engendering the cold rolling texture, while the stability of{111 } texture components in cold rolling is a sufficient condition of emerging thes one.

Causes of the formation of pit defects on the surface of the enamel layer

During the production of the inner walls of ovens,pit defects were formed on the surface of the enamel layer that was enameled on the cold-rolled steel via electrostatic powder spraying and sintering.The paper elaborates on the microstructure and element distribution of the enamel-steel interface and the enamel layer.Optical microscopy,scanning electron microscopy,and energy-dispersive spectroscopy were adopted to investigate the microstructure of a longitudinal section of the defect,and the pit-forming causes were analyzed.The results show that rusty spots lead to pit defects.During high-temperature firing,there is an inadequate fusion and reaction between iron oxides of the rusty spots and the enamel glaze.The rusty spots are closely related to pretreatment process;thus,to avoid their occurrence,electrostatic powder spraying and sintering should be performed timely after forming,degreasing,and thorough drying of the metal sheets.