Effect of Ferric Chloride on the Properties of Biological Sludge in Co-precipitation Phosphorus Removal Process

This paper studied the effect of ferric chloride on waste sludge digestion,dewatering and sedimentation under the optimized doses in co-precipitation phosphorus removal process.The experimental results showed that the concentration of mixed liquid suspended solid(MLSS) was 2436 mg.L-1 and 2385 mg.L-1 in co-precipitation phosphorus removal process(CPR) and biological phosphorous removal process(BPR),respectively.The sludge reduction ratio for each process was 22.6% and 24.6% in aerobic digestion,and 27.6% and 29.9% in anaerobic digestion,respectively.Due to the addition of chemical to the end of aeration tank,the sludge content of CPR was slightly higher than that of BPR,but the sludge reduction rate for both processes had no distinct difference.The sludge volume index(SVI) and sludge specific resistance of BPR were 126 ml.g-1 and 11.7×1012 m.kg-1,respectively,while those of CPR were only 98 ml.g-1 and 7.1×1012 m.kg-1,indicating that CPR chemical could improve sludge settling and dewatering.

Fuzzy Control of Nitrate Recirculation and External Carbon Addition in A/O Nitrogen Removal Process

Nitrogen and phosphorous concentrations of effluent water must be taken into account for the design and operation of wastewater treatment plants. In addition, the requirement for effluent quality is becoming strict. Therefore, intelligent control approaches are recently required in removing biological nutrient. In this study, fuzzy control has been successfully applied to improve the nitrogen removal. Experimental results showed that a close relationship between nitrate concentration and oxidation-reduction potential (ORP) at the end of anoxic zone was found for anoxic/oxic (A/O) nitrogen removal process treating synthetic wastewater. ORP can be used as online fuzzy control parameter of nitrate recirculation and external carbon addition. The established fuzzy logic controller that includes two inputs and one output can maintain ORP value at - 86 mV and - 90 mV by adjusting the nitrate recirculation flow and external carbon dosage respectively to realize the optimal control of nitrogen removal, improving the effluent quality and reducing the operating cost.

Comparative evaluation of processes for heavy metal removal from municipal solid waste incineration fly ash

Hydrochloric acid leaching, chloride evaporation, acetic acid leaching, and biological leaching were evaluated and compared as processes of heavy metal removal for municipal solid waste incineration fly ash(MSWFA). Six factors, namely, energy consumption, process efficiency, process handling, process cost estimation, cost reduction potential, and study progress, were used in order to find out their advantages and disadvantages and to help develop a better recovery process of heavy metals from MSWFA in terms of treatment of the waste material. Hydrochloric acid leaching process was found to be most balanced among the evaluated processes. It showed superiority on energy consumption, process cost estimation, and study progress. On the other hand, despite of its excellency in process efficiency, chloride evaporation process was most unfavorable mainly due to heavy energy dependence. Biological process, with huge potential of cost reduction, was concluded to be the second best process.

Friction behaviors in the metal cutting process:state of the art and future perspectives

Material removal in the cutting process is regarded as a friction system with multiple input and output variables.The complexity of the cutting friction system is caused by the extreme conditions existing on the tool–chip and tool–workpiece interfaces.The critical issue is significant to use knowledge of cutting friction behaviors to guide researchers and industrial manufacturing engineers in designing rational cutting processes to reduce tool wear and improve surface quality.This review focuses on the state of the art of research on friction behaviors in cutting procedures as well as future perspectives.First,the cutting friction phenomena under extreme conditions,such as high temperature,large strain/strain rates,sticking–sliding contact states,and diverse cutting conditions are analyzed.Second,the theoretical models of cutting friction behaviors and the application of simulation technology are discussed.Third,the factors that affect friction behaviors are analyzed,including material matching,cutting parameters,lubrication/cooling conditions,micro/nano surface textures,and tool coatings.Then,the consequences of the cutting friction phenomena,including tool wear patterns,tool life,chip formation,and the machined surface are analyzed.Finally,the research limitations and future work for cutting friction behaviors are discussed.This review contributes to the understanding of cutting friction behaviors and the development of high-quality cutting technology.

Development of a new cleaner production process for cassava ethanol

A new cleaner production process for cassava ethanol has been developed, in which the thin stillage by-product was treated initially by anaerobic digestion, and the digestate further processed by hydrogen-form cation exchange resin before being recycled as process water to make mash for the next ethanol fermentation batch.Thus wastewater was eliminated and freshwater and energy consumption was significantly reduced. To evaluate the new process, ten consecutive batches of ethanol fermentation and anaerobic digestion at lab scale were carried out. Average ethanol production in the recycling batches was 11.43%(v/v) which was similar to the first batch, where deionized(DI) water was used as process water. The chemical oxygen demand(COD) removal rate reached 98% and the methane yield was 322 ml per gram of COD removed, suggesting an efficient and stable operation of the anaerobic digestion. In conclusion, the application of the new process can contribute to sustainable development of the cassava ethanol industry.

反硝化深床滤池在污水处理厂提标改造中的应用实例

惠州市某镇生活污水处理厂一期提标改造工程设计规模万1.0万m3/d,污水处理厂提标前的尾水排放标准采用广东省地方标准《水污染物排放限值》(DB44/26-2001)第二时段一级标准和《城镇污水处理厂污染物排放标准》(GB18918-2002)一级B标准的较严者;提标后采用广东省地方标准《水污染物排放限值》(DB44/26-2001)第二时段一级标准和《城镇污水处理厂污染物排放标准》一级A标准的较严者。提标改造工程增加了混凝池+反硝化深床滤池深度污水处理工艺,通过投加药剂,补充碳源,保证SS、TP和TN同时稳定达标。混凝池+反硝化深床滤池综合了生物脱氮、除磷和过滤的功能,灵活运行,结合前端主体工艺,保证出水稳定达标。

Non-thermal plasma treatment of Radix aconiti wastewater generated by traditional Chinese medicine processing

The wastewater effluent from Radix aconiti processing, an important step in the production processes of traditional Chinese medicine（TCM）, is a type of toxic wastewater and difficult to treat. Plasma oxidation methods have emerged as feasible techniques for effective decomposition of toxic organic pollutants. This study examined the performance of a plasma reactor operated in a dielectric barrier discharge（DBD） to degrade the effluent from R. aconiti processing. The effects of treatment time, discharge voltage, initial pH value and the feeding gas for the reactor on the degradation of this TCM wastewater were investigated. A bacterium bioluminescence assay was adopted in this study to test the toxicity of the TCM wastewater after non-thermal plasma treatment. The degradation ratio of the main toxic component was 87.77% after 60 min treatment with oxygen used as feed gas and it was 99.59% when the initial p H value was 8.0. High discharge voltage and alkaline solution environment were beneficial for improving the degradation ratio. The treatment process was found to be capable of reducing the toxicity of the wastewater to a low level or even render it non-toxic. These experimental results suggested that the DBD plasma method may be a competitive technology for primary decomposition of biologically undegradable toxic organic pollutants in TCM wastewater.