Influence of forming process on three-dimensional morphology of TiB_2 particles in Al-Ti-B alloys

A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on the three-dimensional morphology of TiB2 particles.Different preparation routes result in different reaction forms,which accounts for the morphology variation of TiB2 particles.When the Al-Ti-B master alloy is prepared using ＂halide salt＂ route,TiB2 particles exhibit hexagonal platelet morphology and are independent with each other.In addition,the reaction temperature almost does not have influence on the morphology of TiB2 particles.However,TiB2 particles exhibit different morphologies at different reaction temperatures when the master alloys are prepared with Al-3B and Ti sponge.When the master alloy is prepared at 850 ℃,a kind of TiB2 particle agglomeration forms with a size larger than 5 μm.The TiB2 particles change to layered stacking morphology even dendritic morphology with the reaction temperature reaching up to 1200 ℃.

Research on the Casting-forging Precision Forming Process of Alternator Poles

The casting-forging combined technique and the closed die forging without flash-less are both new developed material working methods. The former can not only decrease forming operations of forgings, but also increase the material utilization ratio. Therefore, it is applied to produce more complex forgings. The latter is required for forging precise parts without burrs. The alternator pole is a complex forging, which was usually produced by hot forging, upsetting-extrusion or upsetting-extrusion and bending processes. During these processes, not only the forming force is higher, but the material of burrs accounts for 30 percent or so of total required material. And burrs are difficult to remove in the sequential machining process. In accordance with defects exiting in current manufacturing of alternator poles by upsetting-extruding process, such as more material demand, higher forming force and difficulty of next machining, a casting-forging precision process of alternator poles was developed and investigated in this paper. In the process, the pole was formed by two operations. One is the pre-forming operation by casting. The other is the final forming operation by the closed precision forging process. This can not only shorten processes, decrease material and power demand, but also increase precision of forgings. First, the casting blocker was designed considering the casting process and the forging ratio and the mode of deformation. Then the die structure for closed precision forging was designed, and the closing device for forging dies with spring assemblies in order to provide the necessary closing force was also designed. Finally the forming processes was investigated by test and numerical simulation method to optimum process parameters and die structure design parameters. The result can provide basis for applying the process to manufacture poles in practice.

Framework of Digital Machining Process Planning Platform for Cylinder Body Part

Digital factory technology is an advanced manufacturing technology served as to establish a bridge between the process of product development and manufacturing.In terms of application for digital factory technology in machining,especially in machining of a complicated part such as a cylinder body part,a concept of digital process planning and its framework are proposed.Its components including machining domain knowledge model,machining knowledge base,machining resource base and process planning system are studied.A machining knowledge model in tree form and an object-driven knowledge reasoning mechanism are used for machining knowledge base.The process planning system is a user interface that leads a planner to finish the planning process.A case about a cylinder head part is given to demonstrate how the platform works.The framework of digital process planning is the foundation of some intelligent CAPP systems and helps to production line planning.

Three-Dimensional Rigid-Plastic FEM Simulation of Bulk Forming Processes with New Contact and Remeshing Techniques

Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic FEM code has been developed. Isothermal forging process of a cylindrical housing has been simulated. The simulation results show that the given techniques and the FEM code are reasonable and feasible for three-dimensional bulk forming processes.

Non-Synchronous Deformation Effect of Particle in Sheet Metal Forming Process

A new concept referred to the non-synchronous deformation effect of particle in sheet metal forming is proposed. The results of finite element analysis show that the flow resistance of sheet metal can be effectively reduced and thus the forming property can be greatly improved if the moving and deformation state of the neighboring elements with equal perpendicular distance to the entrance contour of die is non-synchronous. Experiment tests are presented and the results agree well with FEA simulation. In addition, the mechanism of the non-synchronous effect is analyzed in detail.

Numerical Methodology for Metal Forming Processes Using Elastoplastic Model with Damage Occurrence

Ductile damage often occurs during metal forming processes due to the large thermo-elasto （visco） plastic flow Iocalisation. This paper presents a numerical methodology, which aims to virtually improve any metal forming processes. The methodology is based on elastoplastic constitutive equations accounting for nonlinear mixed isotropic and kinematic hardening strongly coupled with isotropic ductile damage. An adaptive remeshing scheme based on geometrical and physical error estimates including a kill element procedure is used. Some numerical results are presented to show the capability of the model to predict the damage initiation and growth during the metal forming processes.

Studying Formability Limits By Combining Conventional and Incremental Sheet Forming Process

In this work it is assessed the potential of combining conventional and incremental sheet forming processes in a same sheet of metal.This so-called hybrid forming approach is performed through the manufacture of a pre-forming by conventional forming,followed by incremental sheet forming.The main objective is analyzing strain evolution.The pre-forming induced in the conventional forming stage will determine the strain paths,directly influencing the strains produced by the incremental process.To conduct the study,in the conventional processes,strains were imposed in three different ways with distinct true strains.At the incremental stage,the pyramid strategy was adopted with different wall slopes.From the experiments,the true strains and the final geometries were analyzed.Numerical simulation was also employed for the sake of comparison and correlation with the measured data.It could be observed that single-stretch pre-strain was directly proportional to the maximum incremental strains achieved,whereas samples subjected to biaxial pre-strain influenced the formability according to the degree of pre-strain applied.Pre-strain driven by the prior deep-drawing operation did not result,in this particular geometry,in increased formability.

A NON－INCREMENTAL TIME－SPACE ALGORITHM FOR NUMERICAL SIMULATION OF FORMING PROCESS

A non-incremental time-space algorithm is proposed for numerical. analysis of forming process with the inclusion of geometrical, material, contact-frictional nonlinearities. Unlike the widely used Newton-Raphson counterpart, the present scheme features an iterative solution procedure on entire time and space domain. Validity and feasibility of foe present scheme are further justiced by the numerical investigation herewith presented.

EFFECT OF BURNING METHOD ON THE FORMING PROCESSES OF PORTLAND CEMENT CLINKER

The forming temperature of Clinker melt underdifferent burning conditions has been studied by appearance examination and thermal shrinker determination, and the viscosity of melt has been discussed by studying the coordination number of Al^(3+) and Fe^(3+) in cement clinker burned by different method with x^- ray fluorescence analysis and Moss- bauer spectroscopy. The results show that the clin- ker melt under rapid burning may come into exis- tence at lower temperature and It's viscosity is lower. So the forming processes of clinker may be different at rapid burning from ordinary burning. They are probably an important factor to promote the formation of clinker burned at lower temperature with rapid burning method.

The Evolutionary History of Ore-forming Processes of Metallic Ore Deposits in Northern Guangxi

The northern Guangxi region is an important rare metal, rare earth metal and polymetallic metallogenic province. In the region there exist five metallogenic series and two metallogenic subseries, whose metallogenesis shows features of polycyclic spiral evolution throughout the geological history. As far as various cycles are concerned, mantle-derived ore substances were reduced while crust-derived ore substances increased from early to late timesfin the whole geological evolutionary history, mantle-derived substances decreased gradually while crust-derived ones increased. Meanwhile ore element associations became more and more varied. In terms of space, mineralization migrated from the old basement outwards, i.e. from west to east during the Precambrian, and from north to south during the Phanerozoic, and again from east to west during the Yanshanian.

Study on the Forming Process of Yi Medicine Tongfeng Granules

[Objectives]To optimize the forming process of Yi medicine Tongfeng Granules.[Methods]The forming process of Yi medicine Tongfeng Granules was optimized,with paste density,ethanol volume fraction,and type and proportion of excipient as influencing factors,and granule formability,solubility,moisture absorption,and angle of repose as evaluation indicators.Critical relative humidity(CRH)was investigated to select optimal storage conditions.[Results]Maltodextrin was selected as the excipient,and the best process parameters was the ratio of drug to excipient at 1∶2(g/g),under which the forming rate,solubility,moisture absorption rate,and angle of repose were 81.38%,98.90%,8.81%,and 27.5°,respectively.The critical relative humidity was 72%.[Conclusions]The forming process adopted is reasonable and feasible,and can provide a reference for large-scale production of Yi medicine Tongfeng Granules.

Drying Technology and Formation Process of Naomai Xingshen Capsules

[Objectives]To optimize the drying technology and formation process of Naomai Xingshen Capsules.[Methods]The yield of paste powder and moisture content as evaluation indicators were taken as indicators,the relative density of feed liquid,inlet air temperature and dosage of excipients were selected as investigation factors,the orthogonal experiment method was used to optimize the spray drying process.The moisture absorption rate and angle of repose were taken as evaluation indicators,the types of forming excipient were screened,and the critical relative humidity was determined.[Results]The optimum spray drying process was that the relative density of liquid medicine was 1.05(60℃),the air inlet temperature was 200℃,and the dosage of excipients was 2%.The effect of using dextrin as a forming excipient was better,and the relative humidity of the production environment should be controlled below 65%.[Conclusions]The optimized process is stable,feasible,scientific and reasonable,and can be used for large-scale industrial production.

The Design of a Graphical User Environment for Numerical Simulation of Powder Forming Processes

As computer simulation increasingly supports engine er ing design and manufacture, the requirement for a computer software environment providing an integration platform for computational engineering software increas es. A key component of an integrated environment is the use of computational eng ineering to assist and support solutions for complex design. Computer methods fo r structural, flow and thermal analysis are well developed and have been used in design for many years. Many software packages are now available which provi de an advanced capability. However, they are not designed for modelling of powde r forming processes. This paper describes the powder compaction software (PCS_SU T), which is designed for pre- and post-processing for computational simulatio n of the process compaction of powder. In the PCS_SUT software, the adaptive analysis of transient metal powder forming process is simulated by the finite element method based on deformation theories . The error estimates and adaptive remeshing schemes are applied for updated co -ordinate analysis. A generalized Newmark scheme is used for the time domain di scretization and the final nonlinear equations are solved by a Newton-Raphson p rocedure. An incremental elasto-plastic material model is used to simulate the compaction process. To describe the constitutive model of nonlinear behaviour of powder materials, a combination of Mohr-Coulomb and elliptical yield cap model is applied. This model reflects the yielding, frictional and densification char acteristics of powder along with strain and geometrical hardening which occurs d uring the compaction process. A hardening rule is used to define the dependence of the yield surface on the degree of plastic straining. A plasticity theory for friction is employed in the treatment of the powder-tooling interface. The inv olvement of two different materials, which have contact and relative movement in relation to each other, must be considered. A special formulation for friction modelling is coupled with a material formulation. The interface behaviour betwee n the die and the powder is modelled by using an interface element mesh. In the present paper, we have demonstrated pre- and post-processor finite elem ent software, written in Visual Basic, to generate the graphical model and visua lly display the computed results. The software consist of three main part: · Pre-processor: It is used to create the model, generate an app ropriate finite element grid, apply the appropriate boundary conditions, and vie w the total model. The geometric model can be used to associate the mesh with th e physical attributes such as element properties, material properties, or loads and boundary conditions. · Analysis: It can deal with two-dimensional and axi-symmetric applications for linear and non-linear behaviour of material in static and dyna mic analyses. Both triangular and quadrilateral elements are available in the e lement library, including 3-noded, 6-noded and 7-noded (T6B1) triangles and 4 -noded, 8-noded and 9-noded quadrilaterals. The direct implicit algorithm bas ed on the generalized Newmark scheme is used for the time integration and an aut omatic time step control facility is provided. For non-linear iteration, choice s among fully or modified Newton-Raphson method and quasi-Newton method, using the initial stiffness method, Davidon inverse method or BFGS inverse method, ar e possible. · Post-processor: It provides visualization of the computed resu lts, when the finite element model and analysis have been completed. Post-proce ssing is vital to allow the appropriate interpretation of the completed results of the finite element analysis. It provides the visual means to interpret the va st amounts of computed results generated. Finally, the powder behaviour during the compaction of a multi-level component is numerically simulated by the PCS_SUT software, as shown in Fig.1. The predict ive compaction forces at different displacements are computed and compared with the available experimental

Effect of Deformation Condition on Axial Compressive Precision Forming Process of Tube with Curling Die

The effect of the deformation condition on the axial compressive precision forming process of tube with curling die was investigated by using a rigid-plastic FEM. The results show that the forming accuracy depends mainly on geometric condition rp/d0, little on tube material properties and friction condition; the relative gap △/2rp of double-walled tubes obtained decreases with Increasing rp/d0, and there is a parameter k for a given to/do or rp/t0, when rp/d0 >k, △/2rp< 1, otherwise △/2rp>1.

Humanoid Based Intelligence Control Strategy of Plastic Cement Die Press Work-Piece Forming Process for Polymer Plastics

The plastic cement belongs to a sort of polymer material, the chemical composition is very complex, and the plastic cement work-piece is generally manufactured by die press forming. Aimed at being difficult to control in parameters of forming process, the paper explored the humanoid based intelligence control strategy. In the paper, it made the anatomy in control puzzle resulted in uncertainty such as chemical component of plastic cement etc., summarized up the characteristic of cybernetics in forming process, researched on the humanoid based intelligence control strategy, and constructed the control algorithm of forming process in plastic cement work-piece. Taking the process experiment of temperature and pressure control as an example, it validated the good dynamic and static control quality through simulation of control algorithm constructed in this paper. The experimental results show that the control algorithm explored in this paper is reasonably available.

Genesis of Pyroxenite Veins in the Zedang Ophiolite,Southern Tibetan Plateau

Understanding the nature of parental melts for pyroxenite veins in supra-subduction zone(SSZ)ophiolites provides vibrant constraints on melt infiltration processes operating in subduction zones.The Zedang ophiolitic massif in the eastern Yarlung–Zangbo suture zone in Tibet consists of mantle peridotites and a crustal section of gabbro,diabase,and basalt.Veins of two pyroxenite varieties cut the southern part of the Zedang massif.These pyroxenite rocks have different geochemical characteristics,where the first variety(type-I)has relatively higher contents of SiO_(2)(51.82–53.08 wt%),MgO(20.08–23.23 wt%),andΣPGE(3.42–13.97 ppb),and lower Al_(2)O_(3)(1.59–2.28 wt%)andΣREE(1.63–2.94 ppm).The second pyroxenite variety(type-II)is characterized by SiO_(2)(45.44–49.61 wt%),Mg O(16.68–19.78 wt%),Al_(2)O_(3)(4.24–8.77 wt%),ΣPGE(14.46–322.06 ppb),andΣREE(5.82–7.44 ppm).Pyroxenite type-I shows N-MORB-like chondritenormalized REE patterns.Zircon U-Pb ages of pyroxenite type-I(194±10 Ma),associated ophiolitic gabbro(135.3±2.0 Ma),and plagiogranite(124.2±2.3 Ma)evidently imply episodic evolution of the Zedang ophiolites.The mineralogical and geochemical characteristics of the investigated pyroxenites can be explained by subduction-initiated hydrous melting of metasomatized sub-arc mantle,later overprinted by sub-slab mantle melting triggered by upwelling asthenosphere during the Jurassic–Early Cretaceous times.The geochemical variations in pyroxenite vein composition,coupled with age differences amongst the other ophiolite units,may correspond to intermittent emplacement of pyroxenite dikes and isotropic gabbroic intrusions where the geodynamic setting progressed from arc maturation and slab rollback to slab tearing and delamination.

Forming process chain for manufacturing complex conical-section profiled rings:On a co-design method

The final quality of complex conical-section rings depends on co-design of multiple processes in forming process chain.In this study,for a complex aeroengine casing ring with a large slope and a flange on its end,a co-design method of the forming process chain is put forward towards the objective of precision forming,which not only proposes a standard process route composed of multiple processes of upsetting,punching,rectangular ring rolling,loose tooling forging and profiled ring rolling,but also presents co-design methods of dies and blanks for all the processes.For profiled ring rolling,a design method of preformed blank that makes the blank and the target conical-section ring have the same axial volume distribution is proposed.By the method,the axial metal redistribution during the process can be alleviated greatly thus improving the forming stability and precision of the ring.Based on the geometric features of designed preformed blank,design methods of blanks and dies for loose tolling forging,rectangular ring rolling,punching and upsetting are proposed sequentially.In view of the key roles of loose tooling forging(manufacturing the preformed blank)and profiled ring rolling on the final quality of the conical ring parts,inherited FE simulations for these two processes are performed to verify the proposed design methods and determine appropriate design parameter.It is demonstrated that the proposed design method has significant advantages in improving forming precision.Besides,a suggestive value 1.5 of the rolling ratio for profiled ring rolling(a key design parameter)is given based on comprehensive consideration of multiple indicators such as ring roundness,deformation uniformity and forming load.The corresponding industrial experiments performed illustrate that a high forming precision of the conical-section aeroengine casing ring is achieved.

Shear Alteration, Mass Transfer and Gold Mineralization: An Example from Jiaodong Ore Deposit Concentrating Area, Shandong, China

Taking the gold ore deposit concentrating area of Jiaodong area in Shandong, China for an example, based on geological analysis, and applying Gresens’ equation, Grant’s isocon diagram and O’hara microelement calculation method, a thorough study on shear alteration, mass transfer and gold mineralization was carried out. The authors also made mathematic simulation and geochemical analysis. The work reveals temporal spatial changing regularities of temperature field and velocity field of fluids, and also reveals fluid transport chemical reaction coupling metallogenic dynamics of the Jiaojia gold ore concentrating area. During shear alteration process of the Jiaodong gold ore concentrating area, all kinds of components transferred with different amounts, fluid rock ratio was rather high and volume strain was of dilation type. Fast flow of ore forming fluid favors the occurrence of mixed fluid. Shear fractured zones are places where there was strong transportation reaction coupling mineralization. Ore bodies were located in dilation space of shear structure where there was the greatest fluid flux. After the emplacement of the rock body, a convex heat field was formed around the rock body. It is one of the main metallogenic forces. The major reason for mineralization is the mobilization, migration and enrichment of ore forming elements induced by shear compressive extensional tectonism. Inclusion gold dominant low grade ores were formed in the early ore forming stage, while high grade ores, which contained fissure gold and polymetallic veinlets, were formed in late ore forming stage.

MECHANICAL PROPERTIES OF LONGITUDINAL SUBMERGED ARC WELDED STEEL PIPES USED FOR GAS PIPELINE OF OFFSHORE OIL

Since the development of offshore oil and gas, increased submarine oil and gas pipelines were installed. All the early steel pipes of submarine pipelines depended on importing because of the strict requirements of comprehensive properties, such as, anti-corrosion, resistance to pressure and so on. To research and develop domes- tic steel pipes used for the submarine pipeline, the Longitudinal-seam Submerged Arc Welded （LSAW） pipes were made of steel plates cut from leveled hot rolled coils by both the JCOE and UOE （the forming process in which the plate like the letter “J”, “C”, “0” or “U” shape, then expansion） forming processes. Furthermore, the mechanical properties of the pipe base metal and weld metal were tested, and the results were in accordance with the corresponding pipe specification API SPEC 5L or DNV- OS-FI01, which showed that domestic LSAW pipes could be used for submarine oil and gas pipelines.

In situ monitoring methods for selective laser melting additive manufacturing process based on images-A review

Selective laser melting(SLM)has been widely used in the fields of aviation,aerospace and die manufacturing due to its ability to produce metal components with arbitrarily complex shapes.However,the instability of SLM process often leads to quality fluctuation of the formed component,which hinders the further development and application of SLM.In situ quality control during SLM process is an effective solution to the quality fluctuation of formed components.However,the basic premise of feedback control during SLM process is the rapid and accurate diagnosis of the quality.Therefore,an in situ monitoring method of SLM process,which provides quality diagnosis information for feedback control,became one of the research hotspots in this field in recent years.In this paper,the research progress of in situ monitoring during SLM process based on images is reviewed.Firstly,the significance of in situ monitoring during SLM process is analyzed.Then,the image information source of SLM process,the image acquisition systems for different detection objects(the molten pool region,the scanned layer and the powder spread layer)and the methods of the image information analysis,detection and recognition are reviewed and analyzed.Through review and analysis,it is found that the existing image analysis and detection methods during SLM process are mainly based on traditional image processing methods combined with traditional machine learning models.Finally,the main development direction of in situ monitoring during SLM process is proposed by combining with the frontier technology of image-based computer vision.