Secondary analysis of malaria rapid diagnostic tests from rounds 5–8 of WHO product testing with a focus on false-negative results

Despite the widespread use of malaria rapid diagnostic test(RDT)in clinical practice,there are a lot of challenges.We conducted a secondary analysis of 129 malaria RDT data from rounds 5–8 of the World Health Organization(WHO)product testing summary and discuss the causes of false-negative(FN)results with a focus on low parasite density,improper RDT storage,operation and interpretation,and Plasmodium falciparum with a pfhrp2/3 gene deletion.The results demonstrated that the malaria RDTs currently commercially available might cause FN results in practice.

Application of the monitoring and early warning system for internal solitary waves:Take the second natural gas hydrates production test in the South China Sea as an example

Internal solitary waves(ISWs) contain great energy and have the characteristics of emergency and concealment. To avoid their damage to offshore engineering, a new generation of monitoring and early warning system for ISWs was developed using technologies of double buoys monitoring, intelligent realtime data transmission, and automatic software identification. The system was applied to the second natural gas hydrates(NGHs) production test in the Shenhu Area, South China Sea(SCS) and successfully provided the early warning of ISWs for 173 days(from October 2019 to April 2020). The abrupt changes in the thrust force of the drilling platform under the attack of ISWs were consistent with the early warning information, proving the reliability of this system. A total of 93 ISWs were detected around the drilling platform. Most of them occurred during the spring tides in October–December 2019 and April 2020, while few of them occurred in winter. As suggested by the theoretical model, the full-depth structure of ISWs was a typical current profile of mode-1, and the velocities of wave-induced currents can reach 80 cm/s and30 cm/s, respectively, in the upper ocean and near the seabed. The ISWs may be primarily generated from the interactions between the topography and semidiurnal tides in the Luzon Strait, and then propagate westward to the drilling platform. This study could serve as an important reference for the early warning of ISWs for offshore engineering construction in the future.

Physical characteristics of high concentrated gas hydrate reservoir in the Shenhu production test area,South China Sea

High concentrated and heterogeneous distribution of gas hydrates have been identified in the gas hydrate production test region in the Shenhu area,South China Sea.The gas hydrate-bearing sediments with high saturation locate at two ridges of submarine canyon with different thickness and saturations just above the bottom simulating reflection.The crossplots of gamma ray,acoustic impedance(P-impedance)and porosity at four sites show that the sediments can be divided into the upper and lower layers at different depths,indicating different geotechnical reservoir properties.Therefore,the depositional environments and physical properties at two ridges are analyzed and compared to show the different characteristics of hydrate reservoir.High porosity,high P-wave velocity,and coarse grain size indicate better reservoir quality and higher energy depositional environment for gas hydrate at Sites W18 and W19 than those at Sites W11 and W17.Our interpretation is that the base of canyon deposits at Sites W18 and W19 characterized by upward-coarsening units may be turbidity sand layers,thus significantly improving the reservoir quality with increasing gas hydrate saturation.The shelf and slope sliding deposits compose of the fine-grained sediments at Sites W11 and W17.The gas hydrate production test sites were conducted at the ridge of W11 and W17,mainly because of the thicker and larger area of gas hydrate-bearing reservoirs than those at Sites W18 and W19.All the results provide useful insights for assessing reservoir quality in the Shenhu area.

Borehole stability in naturally fractured reservoirs luring production tests

Based on the plane of weakness theory, a model for predicting borehole stability in fractured reservoirs under different stress states was estiblisted and the equations for solving borehole stability were developed. The minimum downhole pressures required to maintain borehole stability under different natural fracture occurrences were calculated by using the data from a well in the Tazhong （central Tarim） area, Tarim Basin, west China. Several conclusions were drawn for naturally fractured reservoirs with a dip angle from less than 10° to greater than 30°. Application in three wells in the Tazhong area indicates that this model is practically useful.

The second natural gas hydrate production test in the South China Sea

Clayey silt reservoirs bearing natural gas hydrates(NGH)are considered to be the hydrate-bearing reservoirs that boast the highest reserves but tend to be the most difficult to exploit.They are proved to be exploitable by the first NGH production test conducted in the South China Sea in 2017.Based on the understanding of the first production test,the China Geological Survey determined the optimal target NGH reservoirs for production test and conducted a detailed assessment,numerical and experimental simulation,and onshore testing of the reservoirs.After that,it conducted the second offshore NGH production test in 1225 m deep Shenhu Area,South China Sea(also referred to as the second production test)from October 2019 to April 2020.During the second production test,a series of technical challenges of drilling horizontal wells in shallow soft strata in deep sea were met,including wellhead stability,directional drilling of a horizontal well,reservoir stimulation and sand control,and accurate depressurization.As a result,30 days of continuous gas production was achieved,with a cumulative gas production of 86.14×104 m3.Thus,the average daily gas production is 2.87×10^4 m^3,which is 5.57 times as much as that obtained in the first production test.Therefore,both the cumulative gas production and the daily gas production were highly improved compared to the first production test.As indicated by the monitoring results of the second production test,there was no anomaly in methane content in the seafloor,seawater,and atmosphere throughout the whole production test.This successful production test further indicates that safe and effective NGH exploitation is feasible in clayey silt NGH reservoirs.The industrialization of hydrates consists of five stages in general,namely theoretical research and simulation experiments,exploratory production test,experimental production test,productive production test,and commercial production.The second production test serves as an important step from the exploratory production test to experimental production test.

Application of wellhead suction anchor technology in the second production test of natural gas hydrates in the South China Sea

Traditional suction anchor technology is mainly used in the fields of subsea structure bearing foundations,single-point mooring systems and offshore wind power.It is characterized by providing sufficient lateral and vertical bearing capacities and lateral bending moment.The anchor structure of a traditional suction anchor structure is improved with wellhead suction anchor technology,where a central pipe is added as a channel for drilling and completion operations.To solve the technical problems of a low wellhead bearing capacity,shallow built-up depth,and limited application of conductor jetting in the second production test of natural gas hydrates(NGHs)in the South China Sea(SCS),the China Geological Survey(CGS)took the lead in independently designing and manufacturing a wellhead suction anchor,which fulfilled the requirements of the production test.This novel anchor was successfully implemented in the second production test for the first time,providing a stable wellhead foundation for the success of the second production test of NGHs in the SCS.

Productive test of a newly drying technology of veneer： intermittent-contact drying of veneer with flexible screen belt

A newly drying technology, intermittent-contact drying of veneer with flexible screen belt (ICD-fbs), was invented and used in poplar veneer drying. Productive test was carried out for validating the practical use of this drying method. The test result shows that to dispose flexible screen belts on the two sides of hot board could help steam discharge remarkably. The veneer dried using ICD-fsb method had smooth and level surface, less deformation and warping, even moisture content, and high utilization rate. The time for opening hot board to discharge steam,which, early or late, is a key to obtain good drying result, was determined at the time when the core's temperature of veneer reaches 100℃ (vaporization). Using ICD-fsb method, the shrinking rates in tangent of veneer were from 1.90% to 2.26% for veneer of 0.4 mm in thickness,2.49% to 4.50% for veneer of 1 mm in thickness and 1.34% to 3.30% for veneer of 1.7 mm in thickness, which are much lower than the results obtained by other drying methods. The method of ICD-fsb offers a reliable technological guarantee for solving the deformation problem of veneer drying, especially the deformation of wood from quick-growing plantation.

Classification of carbonate gas condensate reservoirs using well test and production data analyses

Carbonate reservoir patterns play an important role in the production performance of oil and gas wells,and it is usually classified through static data analysis which cannot reflect the actual well performance.This paper takes the Tazhong No.1 gas field in the Tarim Basin,China as an example to investigate the classification of carbonate reservoirs.The classification method mainly combines well test analysis with production analysis—especially the Blasingame type curve method.Based on the characteristics of type curves for well test analysis and the Blasingame method,the relationship between the type curves and reservoir pattern was established.More than 20 wells were analyzed and the reservoirs were classified into 3 major patterns with 7 sub-classes.Furthermore,the classification results were validated by dynamic performance analysis of wells in the Tazhong No.1 gas field.On the basis of the classification results,well stimulation（i.e.water flooding in a single well） was carried out in three volatile-oil wells,and the oil recovery increased by up to 20%.

A Listening Test of Controlled-Productive Ability

The purpose of the study is to estimate a new testing method of evaluating the student's ability of Listening Comprehension. The problem to be addressed is whether there is evidence to show that the method can discriminate between the testees, separating the above average students from the average and the below-average studentsThus, the controlled-productive listening test will be' found to be reliable, valid (in that the test distinguished between different proficiency students )and practical.

Productivity Testing Design Method of Multi-Factor Control for Unconsolidated Sandstone Gas Reservoir

Reservoir safety, testing-string safety, and flow control are key factors that should be considered in deep-water unconsolidated sandstone gas well testing work system. Combined with the feature of testing reservoir, pipe string type and sea area, the required minimum testing flow rate during cleaning up process, as well as minimum test flow rate without hydrate generation, pipe string erosion critical production, the maximum testing flow rate without destroying sand formation and the minimum output of meeting the demand of development was analyzed;based on the above critical test flow rates, testing working system is designed. Field application showed that the designed work system effectively provided good guidance for field test operations;no sand production or hydrate generation happened during the test process;the test parameter evaluated the reservoir accurately;the safe and efficient test operation was achieved.

On the Production Testing of Memristor Ratioed Logic (MRL) Gates

This paper focuses on the production testing of Memristor Ratioed Logic (MRL) gates. MRL is a family that uses memristors along with CMOS inverters to design logic gates. Two-input NAND and NOR gates are investigated using the stuck at fault model for the memristors and the five-fault model for the transistors. Test escapes may take place while testing faults in the memristors. Therefore, two solutions are proposed to obtain full coverage for the MRL NAND and NOR gates. The first is to apply scaled input voltages and the second is to change the switching threshold of the CMOS inverter. In addition, it is shown that test speed and order should be taken into consideration. It is proven that three ordered test vectors are needed for full coverage in MRL NAND and NOR gates, which is different from the order required to obtain 100% coverage in the conventional NAND and NOR CMOS designs.

China,America Have Coo[erated in Micro Biological Production Test

Ｃｈｉｎａ，ＡｍｅｒｉｃａＨａｖｅＣｏｏｐｅｒａｔｅｄｉｎＭｉｃｒｏｂｉｏｌｏｇｉｃａｌＰｒｏｄｕｃｔｉｏｎＴｅｓｔＨｏｕＦｕＴｈｅｍｉｃｒｏｂｉｏｌｏｇｉｃａｌｐｒｏｄｕｃｔｉｏｎｔｅｃｈｎｏｌｏｇｙｈａｓｂｅｅｎｉｎｔｒｏｄｕｃｅｄｆｒｏｍｔｈｅ...

RESEARCH ON MICROWAVE HUMIDITY TESTING OF CERAMIC PRODUCTS

This paper analyses the principle of microwave humidity testing. According to the problems in the production procedure of ceramic products, a microwave humidity testing system is designed and analyzed for its advantages. Furthermore, the system has been applied to the production line that produces ceramic products and the testing results are also satisfying.

A New Method for Forecasting the Life Test Data of Mechanical Products

The model for forecasting the test data on mechanical products is established in the application of the grey system theories. A new formula of the background value is introduced into the model. The result of an example shows the method can reduce test expense and enhance the precision of forecasting.

Test Method for Refractoriness Under Load of Refractory Products(Non-differential,with Rising Temperature)

This standard specifies the definitions, theory, apparatus, specimens, procedures, test results and disposal, test error and report of test method for refractoriness under load of refractory products （non-differential, with rising temperature）.

日本浅表层水合物勘查试采进展

海洋孔隙填充型水合物已得到较广泛资源调查和经过数次试采,与之相比,以赋存于冷泉、泥底辟和泥火山附近的海底表面和近海底沉积物为主的浅表层水合物的勘查试采工作刚刚起步。日本作为最早实施水合物勘查试采的国家之一,自2013财政年以来在浅表层水合物的资源勘查评价、海洋区域地质调查和环境调查、开发技术调研评价、生产系统构建等方面取得了显著进展。基于文献资料调研,概述了日本水合物研发工作的发展历程以及对浅表层水合物研发工作的整体部署,详细介绍了日本在浅表层水合物勘查试采相关领域开展的主要工作,分析认为,日本在如下4方面取得的实际经验和理论认识值得我国浅表层水合物勘查试采体系化部署借鉴参考:以日本海为主的区域性资源和环境调查,以小范围区域为对象的资源量评价示范,以试采场地优选为目标的精细化资源和环境调查,以及“以使用大口径钻头的大范围垂直采掘方法为基础、优先考虑气体举升回收方法和船载分离方法两项关键技术以形成最优组合”的生产系统设计原则的评估确立。

SYNTHETIC STRESSLIFE TESTING OF MECHATRONIC PRODUCTS UNDER VARIABLE STRESS SPECTRUM

Mechatronic products usually endure the variable stress spectrum when they operate in certain operational condition and environmental condition, which obey the Weibull distribution. In accordance with the features of mechatronic product, this paper analyzes the failure mode, its corresponding sensitive stress and the design principles of life testing profiles. Based on the above analyses, this paper presents a synthetic stress life testing method based on the hybrid Weibull distribution and its statistical method under variable stress spectrum to evaluate the reliability and life indices of mechatronic products. Because the mechatronic products have many characteristics such as high price, long life and small testing samples, the synthetic stress life testing method under variable load spectrum can simulate the real various spectra, decrease the life testing time and reduce the testing samples. So it is effective to carry out the life testing to mechatronic products. The application results of hydraulic pumps indicate that this method can easily handle the experimental data under variable amplitude spectrum, obtain the high precision parameters point estimation and confidence interval estimation and reduce the testing cost greatly.

发制品透气性检测方法的研究

发制品已成为消费者更具时尚性和个性化的消费品。透气性能是衡量发制品穿戴舒适性的关键性能,也是消费者关注的重点。研究了发制品透气性的试验仪器和试验参数,最终制定了发制品透气性的检测方法。试验表明:测试夹具及试验参数可以有效区分不同结构帽底透气性能的好坏,检测方法重现性好,精密度达到可接受水平。