Pressure transient characteristics of non-uniform conductivity fractured wells in viscoelasticity polymer flooding based on oil-water two-phase flow

Polymer flooding in fractured wells has been extensively applied in oilfields to enhance oil recovery.In contrast to water,polymer solution exhibits non-Newtonian and nonlinear behavior such as effects of shear thinning and shear thickening,polymer convection,diffusion,adsorption retention,inaccessible pore volume and reduced effective permeability.Meanwhile,the flux density and fracture conductivity along the hydraulic fracture are generally non-uniform due to the effects of pressure distribution,formation damage,and proppant breakage.In this paper,we present an oil-water two-phase flow model that captures these complex non-Newtonian and nonlinear behavior,and non-uniform fracture characteristics in fractured polymer flooding.The hydraulic fracture is firstly divided into two parts:high-conductivity fracture near the wellbore and low-conductivity fracture in the far-wellbore section.A hybrid grid system,including perpendicular bisection(PEBI)and Cartesian grid,is applied to discrete the partial differential flow equations,and the local grid refinement method is applied in the near-wellbore region to accurately calculate the pressure distribution and shear rate of polymer solution.The combination of polymer behavior characterizations and numerical flow simulations are applied,resulting in the calculation for the distribution of water saturation,polymer concentration and reservoir pressure.Compared with the polymer flooding well with uniform fracture conductivity,this non-uniform fracture conductivity model exhibits the larger pressure difference,and the shorter bilinear flow period due to the decrease of fracture flow ability in the far-wellbore section.The field case of the fall-off test demonstrates that the proposed method characterizes fracture characteristics more accurately,and yields fracture half-lengths that better match engineering reality,enabling a quantitative segmented characterization of the near-wellbore section with high fracture conductivity and the far-wellbore section with low fracture conductivity.The novelty of this paper is the analysis of pressure performances caused by the fracture dynamics and polymer rheology,as well as an analysis method that derives formation and fracture parameters based on the pressure and its derivative curves.

Bacteriological Profile of Effusion Fluids Infections at Charles De Gaulle University Pediatric Hospital from 2017 to 2020

Introduction: Microbiology of effusion fluids in children in Burkina Faso is characterized by the scarcity of data. This work aimed to study the bacteriological and antibiotics susceptibility profile of bacteria involved in effusion fluid infections in paediatrics in order to improve the choice of probabilistic antibiotics therapy. Methods: A cross-sectional, descriptive study was used in children aged 0 to 15 years from 2017 to 2020 at the Charles De Gaulle Pediatric University Hospital Center (CHUP-CDG) in Ouagadougou. Classical bacteriology methods such as macroscopy, Gram staining, identification galleries and antibiotics susceptibility testing were used. Results: Of 231 samples, 64 bacteria were isolated. The most common bacterial strains of pleural fluid were Staphylococcus aureus (25%) and 40% for Enterobacteriaceae. Of the peritoneal fluid, 77% were Enterobacteriaceae with 57% Escherichia coli;and from joint fluid, 33% were S. aureus and 22% for P. aeruginosa. The overall susceptibility profile showed 29% extended-spectrum beta-lactamase-producing Enterobacteriaceae (ESBL), 10% methicillin-resistant S. aureus (MRSA), and 8% carbapenemases. Conclusion: Bacteriological profile is characterized by ESBL-producing Enterobacteriaceae and MRSA. The most active antibiotics were macrolides, aminoglycosides, and cefoxitin (methicillin) for Gram-positive cocci, carbapenems, and aminoglycosides for Gram-negative bacilli. Then, the monitoring of antibiotics resistance must be permanent.

Characteristics and mechanism of smart fluid for sweep-controlling during CO_(2) flooding

A smart response fluid was designed and developed to overcome the challenges of gas channeling during CO_(2)flooding in low-permeability,tight oil reservoirs.The fluid is based on Gemini surfactant with self-assembly capabilities,and the tertiary amine group serves as the response component.The responsive characteristics and corresponding mechanism of the smart fluid during the interaction with CO_(2)/oil were studied,followed by the shear characteristics of the thickened aggregates obtained by the smart fluid responding to CO_(2).The temperature and salt resistance of the smart fluid and the aggregates were evaluated,and their feasibility and effectiveness in sweep-controlling during the CO_(2)flooding were confirmed.This research reveals:(1)Thickened aggregates could be assembled since the smart fluid interacted with CO_(2).When the mass fraction of the smart fluid ranged from 0.05%to 2.50%,the thickening ratio changed from 9 to 246,with viscosity reaching 13 to 3100 mPas.As a result,the sweep efficiency in low-permeability core models could be increased in our experiments.(2)When the smart fluid(0.5%to 1.0%)was exposed to simulated oil,the oil/fluid interfacial tension decreased to the level of 1×10^(-2)mN/m.Furthermore,the vesicle-like micelles in the smart fluid completely transformed into spherical micelles when the fluid was exposed to simulated oil with the saturation greater than 10%.As a result,the smart fluid could maintain low oil/fluid interfacial tension,and would not be thickened after oil exposure.(3)When the smart fluid interacted with CO_(2),the aggregates showed self-healing properties in terms of shear-thinning,static-thickening,and structural integrity after several shear-static cycles.Therefore,this fluid is safe to be placed in deep reservoirs.(4)The long-term temperature and salt resistance of the smart fluid and thickened aggregates have been confirmed.

Profile improvement during CO_2 flooding in ultra-low permeability reservoirs

Gas flooding such as CO2 flooding may be effectively applied to ultra-low permeability reservoirs, but gas channeling is inevitable due to low viscosity and high mobility of gas and formation heterogeneity. In order to mitigate or prevent gas channeling, ethylenediamine is chosen for permeability profile control. The reaction mechanism of ethylenediamine with CO2, injection performance, swept volume, and enhanced oil recovery were systematically evaluated. The reaction product of ethylenediamine and CO2 was a white solid or a light yellow viscous liquid, which would mitigate or prevent gas channeling. Also, ethylenediamine could be easily injected into ultra-low permeability cores at high temperature with protective ethanol slugs. The core was swept by injection of 0.3 PV ethylenediamine. Oil displacement tests performed on heterogeneous models with closed fractures, oil recovery was significantly enhanced with injection of ethylenediamine. Experimental results showed that using ethylenediamine to plug high permeability layers would provide a new research idea for the gas injection in fractured, heterogeneous and ultra-low permeability reservoirs. This technology has the potential to be widely applied in oilfields.

Advances of supercritical fluid chromatography in lipid profiling

Supercritical fluid chromatography(SFC) meets with great favor due to its high efficiency, low organic solvent consumption, and the specialty for the identification of the isomeric species. This review describes the advances of SFC in targeted and untargeted lipid profiling. The advancement of the SFC instruments and the stationary phases are summarized. Typical applications of SFC to the targeted and untargeted lipid profiling are discussed in detail. Moreover, the perspectives of SFC in the lipid profiling are also proposed. As a useful and promising tool for investigating lipids in vitro and in vivo, SFC will predictably obtain further development.

Production characteristics and displacement mechanisms of infilling polymer-surfactant-preformed particle gel flooding in post-polymer flooding reservoirs:A review of practice in Ng3 block of Gudao Oilfield

The pilot test of infilling polymer-surfactant-preformed particle gel(PPG)flooding has been successfully implemented after polymer flooding in Ng3 block of Gudao Oilfield in China.However,the production characteristics and displacement mechanisms are still unclear,which restricts its further popularization and application.Aiming at this problem,this paper firstly analyzes the production performance of the pilot test and proposed four response types according to the change of water cut curves,including W-type,U-type,V-type response,and no response.Furthermore,the underlying reasons of these four types are analyzed from the aspects of seepage resistance and sweep efficiency.The overall sweep efficiency of gradual-rising W-type,gradual-decreasing W-type,and early V-type response increases from 0.81 to 0.93,0.55 to 0.89,and 0.94 to 1,respectively.And the sum of seepage resistance along the connection line between production well and injection well for U-type and delayed V-type response increases from 0.0994 to 0.2425,and 0.0677 to 0.1654,respectively.Then,the remaining oil distribution after polymer flooding is summarized into four types on the basis of production and geological characteristics,namely disconnected remaining oil,streamline unswept remaining oil,rhythm remaining oil,and interlayer-controlled remaining oil.Furthermore,the main displacement mechanisms for each type are clarified based on the dimensionless seepage resistance and water absorption profile.Generally,improving connectivity by well pattern infilling is the most important for producing disconnected remaining oil.The synergistic effect of well pattern infilling and polymer-surfactant-PPG flooding increases the dimensionless seepage resistance of water channeling regions and forces the subsequent injected water to turn to regions with streamline unswept remaining oil.The improvement of the water absorption profile by polymer-surfactant-PPG flooding and separated layer water injection contributes to displacing rhythm remaining oil and interlayer-controlled remaining oil.Finally,the paper analyzes the relationships between the remaining oil distribution after polymer flooding and production characteristics of infilling polymer-surfactant-PPG flooding.The study helps to deepen the understanding of infilling polymer-surfactant-PPG flooding and has reference significance for more commercial implementations in the future.

Performance Analysis of a Profile Control Agent for Waste Drilling Fluid Treatment

A method for the treatment of hazardous waste drilling fluids,potentially leading to environmental pollution,is considered.The waste drilling fluid is treated with an inorganic flocculant,an organic flocculant,and a pH regulator.The profile control agent consists of partially hydrolyzed polyacrylamide,formaldehyde,hexamethylenetetramine,resorcinol,phenol,and the treated waste drilling fluid itself.For a waste drilling fluid concentration of 2500 mg/L,the gelling time of the profile control agent is 25 h,and the gelling strength is 32,000 mPa.s.Compared with the profile control agent prepared by recirculated water under the same conditions,the present profile control agent displays better stability,salt-resistance,and performance.

Pilot Test for Nitrogen Foam Flooding in Low Permeability Reservoir

Due to the characteristics of reservoir formation,the producing level of low permeability reservoir is relatively very low.It is hard to obtain high recovery through conventional development schemes.Considering the tight matrix,complex fracture system,low production level of producers,and low recovery factor ofMblock in Xinjiang oilfield,it is selected for on-site pilot test of nitrogen foam flooding.Detailed flooding scheme is made and the test results are evaluated respectively both for producers and injectors.The pressure index,filling degree,and fluid injection profile are found to be all improved in injectors after injection of nitrogen foam.The oil production,water cut and liquid production file are also improved in most of the producers,with the natural decline rate in the test area become slow.Results show that nitrogen foam flooding technology can be good technical storage for enhanced oil recovery in low permeability reservoir.

Oil Production Optimization by Means of a Combined“Plugging,Profile Control,and Flooding”Treatment:Analysis of Results Obtained Using Computer Tomography and Nuclear Magnetic Resonance

Due to long-term water injection,often oilfields enter the so-called medium and high water cut stage,and it is difficult to achieve good oil recovery and water reduction through standard methods(single profile control and flooding measures).Therefore,in this study,a novel method based on“plugging,profile control,and flooding”being implemented at the same time is proposed.To assess the performances of this approach,physical simulations,computer tomography,and nuclear magnetic resonance are used.The results show that the combination of a gel plugging agent,a polymer microsphere flooding agent,and a high-efficiency oil displacement agent leads to better results in terms of oil recovery with respect to the situation in which these approaches are used separately(the oil recovery is increased by 15.37%).Computer tomography scan results show that with the combined approach,a larger sweep volume and higher oil washing efficiency are obtained.The remaining oil in the cluster form can be recovered in the middle and low permeability layer,increasing the proportion of the columnar and blind end states of the oil.The nuclear magnetic resonance test results show that the combined“plugging,profile control,and flooding”treatment can also be used to control more effectively the dominant channels of the high permeability layer and further expand the recovery degree of the remaining oil in the pores of different sizes in the middle and low permeability layers.However,for the low permeability layer(permeability difference of 20),the benefits in terms of oil recovery are limited.

Messenger RNA Profiling for Forensic Body Fluid Identification： Research and Applications

Identifying the origin of body fluids left at a crime scene can give a significant insight into crime scene reconstruction by supporting a link between sample donors and actual criminal acts.However,the conventional body fluid identification methods are prone to various limitations,such as time consumption,intensive labor,nonparallel manner,varying degrees of sensitivity and limited specificity.Recently,the analysis of cell-specific messenger RNA expression(mRNA profiling)has been proposed to supplant conventional methods for body fluid identification.Since 2011,the collaborative exercises have been organized by the European DNA Profiling Group(EDNAP)in order to evaluate the robustness and reproducibility of mRNA profiling for body fluid identification.The major advantages of mRNA profiling,compared to the conventional methods,include higher sensitivity,greater specificity,the ability of detecting several body fluids in one multiplex reaction,and compatibility with current DNA extraction and analysis procedure.In the current review,we provided an overview of the present knowledge and detection methodologies of mRNA profiling for forensic body fluid identification and discussed its possible practical application to forensic casework.

Computational fluid dynamic simulations on liquid film behaviors at flooding in an inclined pipe

The complex liquid film behaviors at flooding in an inclined pipe were investigated with computational fluid dynamic(CFD) approaches. The liquid film behaviors included the dynamic wave characteristics before flooding and the transition of flow pattern when flooding happened. The influences of the surface tension and liquid viscosity were specially analyzed. Comparisons of the calculated velocity at the onset of flooding with the available experimental results showed a good agreement. The calculations verify that the fluctuation frequency and the liquid film thickness are almost unaffected by the superficial gas velocity until the flooding is triggered due to the Kelvin–Helmholtz instability. When flooding triggered at the superficial liquid velocity larger than0.15 m·s-1, the interfacial wave developed to slug flow, while it developed to entrainment flow when it was smaller than 0.08 m·s-1. The interfacial waves were more easily torn into tiny droplets with smaller surface tension, eventually evolving into the mist flow. When the liquid viscosity increases, the liquid film has a thicker holdup with more intensive fluctuations, and more likely developed to the slug flow.

Assessment of Land Erosion and Sediment Accumulation Caused by Runoff after a Flash-Flooding Storm Using Topographic Profiles and Spectral Indices

This research deals with the characterization of areas associated with flash floods and erosion caused by severe rainfall storm and sediment transport and accumulation using topographic attributes and profiles, spectral indices (SI), and principal component analysis (PCA). To achieve our objectives, topographic attributes and profiles were retrieved from ASTER-V2 DEM. PCA and nine SI were derived from two Landsat-OLI images acquired before and after the flood-storm. The images data were atmospherically corrected, sensor radiometric drift calibrated, and geometric and topographic distortions rectified. For validation purposes, the acquired photos during the flood-storm, lithological and geological maps were used. The analysis of approximately 100 colour composite combinations in the RGB system permitted the selection of two combinations due to their potential for characterizing soil erosion classes and sediment accumulation. The first considers the “Intensity, NDWI and NMDI”, while the second associates form index (FI), brightness index (BI) and NDWI. These two combinations provide very good separating power between different levels of soil erosion and degradation. Moreover, the derived erosion risk and sediment accumulation map based on the selected spectral indices segmentation and topographic attributes and profiles illustrated the tendency of water accumulation in the landscape, and highlighted areas prone to both fast moving and pooling water. In addition, it demonstrated that the rainfall, the topographic morphology and the lithology are the major contributing factors for flash flooding, catastrophic inundation, and erosion risk in the study area. The runoff-water power delivers vulnerable topsoil and contributes strongly to the erosion process, and then transports soil material and sediment to the plain areas through waterpower and gravity. The originality of this research resides in its simplicity and rapidity to provide a solid basis strategy for regional policies to address the real causes of problems and risks in developing countries. Certainly, it can help in the improvement of the management of water regulation structures to develop a methodology to maximize the water storage capacity and to reduce the risks caused by floods in the Moroccan Atlas Mountain (Guelmim region).

Monte Carlo Simulations of Density Profiles for Hard-Sphere Chain Fluids Confined Between Surfaces

Covering a wide range of bulk densities, density profiles for hard-sphere chain fluids (HSCFs) with chain length of 3,4,8,20,32 and 64 confined between two surfaces were obtained by Monte Carlo simulations using extended continuum configurational-bias (ECCB) method. It is shown that the enrichment of beads near surfaces is happened at high densities due to the bulk packing effect, on the contrary, the depletion is revealed at low densities owing to the configurational entropic contribution. Comparisons with those calculated by density functional theory presented by Cai et al. indicate that the agreement between simulations and predictions is good. Compressibility factors of bulk HSCFs calculated using volume fractions at surfaces were also used to test the reliability of various equations of state of HSCFs by different authors.

Mathematical modeling of fluid flow and level profile during twin-roll strip casting process

In twin-roll strip casting process,transport phenomena of fluid in the molten pool directly affect the process stability and the quality of products.In order to elucidate the fundamental transport phenomena in twin-roll casting,a commercial software called ProCAST was employed to simulate the transient fluid flow and level profile behaviors during the early stage of the process in this study.The coupled set of governing differential equations for mass,momentum and energy balance were solved with the finite element method and the transient free surface problem was treated with a volume of fluids(VOF) approach.The effect of different delivery systems configuration on flow pattern,level profile in the pool was studied and analyzed in this paper. The new wedge metal delivery systems have been optimized for the twin-roll strip caster.It was shown that new type metal delivery systems had a preferable effect on the uniform distribution of fluid and level fluctuation in the pool.The simulation results also provide a valuable basis for the optimization of delivery system and process parameters during the initial pouring stage.

Comparison of oil displacement mechanisms and performances between continuous and dispersed phase flooding agents

To compare the oil displacement mechanisms and performances of continuous phase flooding agent(traditional polymer solution) and dispersed phase flooding agent(particle-type polymer SMG dispersion), the particle phase separation of SMG dispersion migrating in pores was simulated by using the microfluidic technology. Theoretically guided by the tree fork concentration distribution of red cells in biological fluid mechanics, the concentration distribution mathematical model of SMG in different pores is established. Furthermore, the micro and macro physical simulation experiments of continuous and dispersed phase flooding agents were carried out. The results show that the continuous flooding agent enters all the swept zones and increases the flow resistance in both larger and small pores. On the contrary, the particle phase separation phenomenon occurs during the injection process of dispersed flooding agent. The SMG particles gather in the larger pore to form bridge blinding, and the carrier fluid displace oil in the small pore. Working in cooperation, the SMG particle and carrier fluid drive the residual oil in the low permeability layers step by step and achieve the goal of enhanced oil recovery. The laboratory experimental results indicate that, the oil increment and water reduction effect of dispersed flooding agent is much better than that of continuous flooding agent, which is consistent with the field test results.

Study of the Chemical Flooding Effect in Gao-63 Reservoir

This article is aimed to discuss the impact of using two different kinds of surfactant in enhancing oil recovery in heterogeneous reservoirs. With the background of Jidong oilfield, Rui Feng surfactant which could reach ultra-low interracial tension and combination surfactant RZ-JD80 with strong emulsifying property are chosen to do oil displacement and profile control-oil displacement experiment in homogeneous core and heterogeneous core respectively. The experiment is aimed to study the effect of oil displacement by injecting surfactant individually and the effect after injecting different profile control agent slug before surfactant flooding in heterogeneous cores. The results suggest that injecting Rui Feng surfactant and RZ-JD80 individually could enhance the oil displacement efficiency about 15 percentage points for homogeneous core. For strongly heterogeneous core, it is low efficiency by using either of these two surfactants individually. However, if injected a very little profile control agent slug before surfactant flooding, both of these two kinds of surfactant could enhance the oil recovery by different degree, especially, polymer microsphere plugging^RZ-JD80 flooding composite technology is more adaptable to Gao-63 reservoir. This technology could increase the recovery by 18.52 percentage points aRer surfactant flooding.

Changes in energetic profile of pregnant ewes in relation with the composition of the fetal fluids

Objective: To evaluate the energetic profile of fetal fluids and to make comparisons of the concentrations of the constituents present with those in the maternal plasma.Methods: A study was conducted in 102 gravid sheep uteri. The four stages of gestation as Stage I(0–60 days), Stage II(61–90 days), Stage III(91–120 days) and Stage IV(121–145 days) were identified based on the crown anus length of the embryo/fetus. The amniotic and allantoic fluids collected from the gravid uteri of each group were subjected to biochemical analysis of glucose, cholesterol and triglyceride.Results: The levels of glucose and triglyceride in maternal plasma were lower(P < 0.05)on late pregnancy as well as in amniotic and allantoic fluids. No significant variation(P > 0.05) of plasma cholesterol levels was detected between the sampling periods.Contrariwise, cholesterol concentrations of fetal fluids were higher in Stages III and IV of pregnancy when compared with the Stages I and II.Conclusions: The influence of pregnancy on the biochemical composition of fetal fluids was statistically significant.

Simultaneous measurement of velocity profile and liquid film thickness in horizontal gas–liquid slug flow by using ultrasonic Doppler method

Horizontal gas-liquid two-phase flows widely exist in chemical engineering,oil/gas production and other important industrial processes.Slug flow pattern is the main form of horizontal gas-liquid flows and characterized by intermittent motion of film region and slug region.This work aims to develop the ultrasonic Doppler method to realize the simultaneous measurement of the velocity profile and liquid film thickness of slug flow.A single-frequency single-channel transducer is adopted in the design of the field-programmable gate array based ultrasonic Doppler system.A multiple echo repetition technology is used to improve the temporal-spatial resolution for the velocity profile.An experiment of horizontal gas-liquid two-phase flow is implemented in an acrylic pipe with an inner diameter of 20 mm.Considering the aerated characteristics of the liquid slug,slug flow is divided into low-aerated slug flow,high-aerated slug flow and pseudo slug flow.The temporal-spatial velocity distributions of the three kinds of slug flows are reconstructed by using the ultrasonic velocity profile measurement.The evolution characteristics of the average velocity profile in slug flows are investigated.A novel method is proposed to derive the liquid film thickness based on the instantaneous velocity profile.The liquid film thickness can be effectively measured by detecting the position and the size of the bubbles nearly below the elongated gas bubble.Compared with the time of flight method,the film thickness measured by the Doppler system shows a higher accuracy as a bubble layer occurs in the film region.The effect of the gas distribution on the film thickness is uncovered in three kinds of slug flows.

Simulation of Stripper Flooding Due to the Increase of Feed Flowrate

In this investigation, UniSim software and the Soave-Redlich-Kong (SRK) thermodynamic model were utilized to study flooding in a Naphta stripping column. The objective of this study was to evaluate the impact of increasing feed flowrate from a design load of 121 m3/hr. to 165 m3/hr. on the performance of the plate column. In order to study only flooding in the column, UniSim software was run by keeping the LPG (Liquefied Gas petroleum) and Naphta products within the required specifications. According to the original design specifications of the stripping column, it should not be operated at high feed rates and differential pressure must not exceed 600 mbar. For the purpose of simulation, this value corresponds to a maximum allowable flooding percentage of 85%. The simulation results show that the flooding percentage was 144.5% in the case under study and 83.7% for the design case. Flooding occurred in all parts of the column with diameters of 2 m and 2.7 m. For the case under investigation, the reflux to feed ratio was reduced from 0.45 (design case) to 0.2. The originality of this investigation is the utilization of the temperature profile in the column as a tool to detect the plates where flooding could take place. The column temperature profile during the case under study suggests instability in the plates between trays 5 to 15. It is therefore suspected that flooding takes place mainly between those plates.

Theory and Application of Numerical Simulation of Chemical Flooding in High Temperature and High Salt Reservoirs

Applications, theoretical analysis and numerical methods are introduced for the simulation of mechanical models and principles of the porous flow in high temperature, high salt, complicated geology and large-scale reservoirs in this paper. Considering petroleum geology, geochemistry, computational permeation fluid mechanics and computer technology, we state the models of permeation fluid mechanics and put forward a sequence of implicit upwind difference iteration schemes based on refined fractional steps of the upstream, which can compute the pressures, the saturation and the concentrations of different chemistry components. A type of software applicable in major industries has been completed and carried out in numerical analysis and simulations of oil extraction in Shengli Oil-field, which brings huge economic benefits and social benefits. This software gives many characters: spatial steps are taken as ten meters, the number of nodes is up to hundreds of thousands and simulation time period can be tens of years and the high-order accuracy can be promised in numerical data. Precise analysis is present for simplified models of this type and that provides a tool to solve the international famous problem.