Experimental research on the instability propagation characteristics of liquid kerosene rotating detonation wave

In order to study the instability propagation characteristics of the liquid kerosene rotating detonation wave(RDW),a series of experimental tests were carried out on the rotating detonation combustor(RDC)with air-heater.The fuel and oxidizer are room-temperature liquid kerosene and preheated oxygenenriched air,respectively.The experimental tests keep the equivalence ratio of 0.81 and the oxygen mass fraction of 35%unchanged,and the total mass flow rate is maintained at about 1000 g/s,changing the total temperature of the oxygen-enriched air from 620 K to 860 K.Three different types of instability were observed in the experiments:temporal and spatial instability,mode transition and re-initiation.The interaction between RDW and supply plenum may be the main reason for the fluctuations of detonation wave velocity and pressure peaks with time.Moreover,the inconsistent mixing of fuel and oxidizer at different circumferential positions is related to RDW oscillate spatially.The phenomenon of single-double-single wave transition is analyzed.During the transition,the initial RDW weakens until disappears,and the compression wave strengthens until it becomes a new RDWand propagates steadily.The increased deflagration between the detonation products and the fresh gas layer caused by excessively high temperature is one of the reasons for the RDC quenching and re-initiation.

Laboratory-scale investigation of response characteristics of liquid-filled rock joints with different joint inclinations under dynamic loading

In underground rock engineering,water-bearing faults may be subjected to dynamic loading,resulting in the coupling of hydraulic and dynamic hazards.Understanding the interaction mechanism between the stress waves induced by dynamic loadings and liquid-filled rock joints is therefore crucial.In this study,an auxiliary device for simulating the liquid-filled layer was developed to analyze the dynamic response characteristics of liquid-filled rock joints in laboratory.Granite and polymethyl methacrylate(PMMA)specimens were chosen for testing,and high-amplitude shock waves induced by a split Hopkinson pressure bar(SHPB)were used to produce dynamic loadings.Impact loading tests were conducted on liquid-filled rock joints with different joint inclinations.The energy propagation coefficient and peak liquid pressure were proposed to investigate the energy propagation and attenuation of waves propagating across the joints,as well as the dynamic response characteristics of the liquid in the liquid-filled rock joints.For the inclination angle range considered herein,the experimental results showed that the energy propagation coefficient gently diminished with increasing joint inclination,and smaller coefficient values were obtained for granite specimens compared with PMMA specimens.The peak liquid pressure exhibited a gradually decreasing trend with increasing joint inclination,and the peak pressure for granite specimens was slightly higher than that for PMMA specimens.Overall,this paper may provide a considerably better method for studying liquid-filled rock joints at the laboratory scale,and serves as a guide for interpreting the underlying mechanisms for interactions between stress waves and liquid-filled rock joints.

Mechanical properties and failure characteristics of fractured sandstone with grouting and anchorage

Based on uniaxial compression experimental results on fractured sandstone with grouting and anchorage, we studied the strength and deformation properties, the failure model, crack formation and evolution laws of fractured sandstone under different conditions of anchorage. The experimental results show that the strength and elastic modulus of fractured sandstone with different fracture angles are significantly lower than those of intact sandstone. Compared with the fractured samples without anchorage,the peak strength, residual strength, peak and ultimate axial strain of fractured sandstone under different anchorage increase by 64.5–320.0%, 62.8–493.0%, and 31.6–181.4%, respectively. The number of bolts and degree of pre-stress has certain effects on the peak strength and failure model of fractured sandstone. The peak strength of fractured sandstone under different anchorage increases to some extent, and the failure model of fractured sandstone also transforms from tensile failure to tensile–shear mixed failure with the number of bolts. The pre-stress can restrain the formation and evolution process of tensile cracks, delay the failure process of fractured sandstone under anchorage and impel the transformation of failure model from brittle failure to plastic failure.

Study on Propagation Characteristics of Plasma Surface Wave in Medium Tube

Axial propagation characteristics of the axisymmetric surface wave along the plasma in the medium tube were studied. The expressions of electromagnetic field inside and outside the medium tube were deduced. Also, the impacts of several factors, such as plasma density, signal frequency, inner radius of medium tube, collision frequency, etc., on plasma surface wave propa- gation were numerically simulated. The results show that, the properties of plasma with higher density and lower gas pressure are closer to those of metal conductor. Furthermore, larger radius of medium tube and lower signal frequency are better for surface wave propagation. However, the effect of collision frequency is not obvious. The optimized experimental parameters can be chosen as the plasma density of about 10^17 m^-3 and the medium radius between 11 mm and 19 mm.

Gaussian beamed millimetre wave propagation characteristics due to reflecting behaviour in circle tunnel

Propagation characterization is one of the main building blocks for millimetre wave （MMW） communication. The Gaussian beam has attractive features to become a prospective wave form for millimetre radio communication, especially for the utility inside tunnels. A ray tracing method embedded with spectral features of Gaussian beam is employed to analyze mil- limetre wave propagation in a circle tunnel in this paper. In consideration of geometrical figure of the tunnel, the superposition behaviour of direct and reflective beams is analyzed via simplified approximation of Gaussian beam spectral feature. Then the propagation models are established to derive amplitude, phase, and delay spread of received wave. A typical straight tunnel model is used to simulate the propagation behaviour, where strong multi-path effect with deeply fading of signal intensity and dramatically enhancing of delay spread emerges. For investigation of the spectral feature of the multi-path effect, a reflection loss of 14 dB is taken into consideration at a designated point. To analyze the influences of frequency and transmission distance, the propagation characteristics at three different frequencies of 45 GHz, 65 GHz and 85 GHz are compared with the beam travelling down the tunnel. In addition, three different reflection losses of 14 dB, 20 dB, and 26 dB at the frequency of 65 GHz are also investigated to research the influence of the reflecting coefficient.

Detonation Propagation Characteristics of Superposition Explosive Materials

In order to investigate detonation propagation characteristics of different charge patterns,the detonation velocities of superposition strip shaped charges made up of a detonating cord and explosives were measured by a detonation velocity measuring instrument under conditions of different ignition.The experimental results and theoretical analysis show that the maximum detonation propagation velocity depends on the explosive materials with the maximum velocity among all the explosive materials.Using detonating cord in a superposition charge can shorten detonation propagation time and improve the efficiency of explosive energy.The measurement method of detonation propagation velocity and experimental results are presented and investigated.

Research on phase shift characteristics of electromagnetic wave in plasma

The phase shift characteristics reflect the state change of electromagnetic wave in plasma sheath and can be used to reveal deeply the action mechanism between electromagnetic wave and plasma sheath.In this paper,the phase shift characteristics of electromagnetic wave propagation in plasma were investigated.Firstly,the impact factors of phase shift including electron density,collision frequency and incident frequency were discussed.Then,the plasma with different electron density distribution profiles were employed to investigate the influence on the phase shift characteristics.In a real case,the plasma sheath around the hypersonic vehicle will affect and even break down the communication.Based on the hypersonic vehicle model,we studied the electromagnetic wave phase shift under different flight altitude,speed,and attack angle.The results indicate that the phase shift is inversely proportional to the flight altitude and positively proportional to the flight speed and attack angle.Our work provides a theoretical guidance for the further research of phase shift characteristics and parameters inversion in plasma.

Lateral stress-induced propagation characteristics in photonic crystal fibres

Using the finite element method, this paper investigates lateral stress-induced propagation characteristics in a photonic crystal fibre of hexagonal symmetry. The results of simulation show the strong stress dependence of effective index of the fundamental guided mode, phase modal birefringence and confinement loss. It also finds that the contribution of the geometrical effect that is related only to deformation of the photonic crystal fibre and the stress-related contribution to phase modal birefringence and confinement loss are entirely different. Furthermore, polarization-dependent stress sensitivity of confinement loss is proposed in this paper.

The Propagation Characteristics of the Electron Beam with Initial Modulation

The propagation characteristics of the beam under various initial conditions are in-vestigated by means of PIC method.The influences of density modulation and velocity modulationon the propagation characteristics are discussed and compared.The results reveal that by chang-iug the amplitude of the two kinds of modulations and the phase difference between them,the

ELM-Based Impact Analysis of Meteorological Parameters on the Radio Transmission of X-Band over the Qiongzhou Strait of China

Communication in the evaporation duct layer is greatly affected by the variation of meteorological parameters.Based on the experimental result of the radio transmission of the X-band over the Qiongzhou Strait of China,the characteristic of the duct and its influence on the transmission effect is analyzed.The results indicate that the evaporation duct height(EDH)has a negative Spearman’s rank correlation of-0.90 with the relative humidity and a positive correlation coefficient of 0.84 with the wind speed.Based on the Extreme Learning Machine(ELM)network,we proposed a Met-ELM model that can provide efficient support in predicting propagation characteristics at nighttime.The predicted results of the MetELM model are consistent with the measurements;the root-mean-square-error is 1.66 dB,with the correlation coefficient reaching 0.96,while the proportion of mean absolute error less than 2 dB has reached81.41%.The data-derived Met-ELM model shows great accuracy in predicting propagation characteristics at nighttime,which also meets the acceptable requirements for radio wave propagation.

Role of the 10–20-Day Oscillation in Sustained Rainstorms over Hainan,China in October 2010

Hainan,an island province of China in the northern South China Sea,experienced two sustained rainstorms in October 2010,which were the most severe autumn rainstorms of the past 60 years.From August to October 2010,the most dominant signal of Hainan rainfall was the 10-20-day oscillation.This paper examines the roles of the 10-20-day oscillation in the convective activity and atmospheric circulation during the rainstorms of October 2010 over Hainan.During both rainstorms,Hainan was near the center of convective activity and under the influence of a lower-troposphere cyclonic circulation.The convective center was initiated in the west-central tropical Indian Ocean several days prior to the rainstorm in Hainan.The convective center first propagated eastward to the maritime continent,accompanied by the cyclonic circulation,and then moved northward to the northern South China Sea and South China,causing the rainstorms over Hainan.In addition,the westward propagation of convection from the tropical western Pacific to the southern South China Sea,as well as the propagation farther northward,intensified the convective activity over the northern South China Sea and South China during the first rainstorm.

A Predictive 6G Network with Environment Sensing Enhancement:From Radio Wave Propagation Perspective

In order to support the future digital society,sixth generation(6G)network faces the challenge to work efficiently and flexibly in a wider range of scenarios.The traditional way of system design is to sequentially get the electromagnetic wave propagation model of typical scenarios firstly and then do the network design by simulation offline,which obviously leads to a 6G network lacking of adaptation to dynamic environments.Recently,with the aid of sensing enhancement,more environment information can be obtained.Based on this,from radio wave propagation perspective,we propose a predictive 6G network with environment sensing enhancement,the electromagnetic wave propagation characteristics prediction enabled network(EWave Net),to further release the potential of 6G.To this end,a prediction plane is created to sense,predict and utilize the physical environment information in EWave Net to realize the electromagnetic wave propagation characteristics prediction timely.A two-level closed feedback workflow is also designed to enhance the sensing and prediction ability for EWave Net.Several promising application cases of EWave Net are analyzed and the open issues to achieve this goal are addressed finally.

Simulation Study and Probe on UWB Wireless Communication in Underground Coal Mine

From an analysis of the status of coal mine underground wireless communication, the application of UWB wireless communication system to underground coal mine is proposed. The basic composition of an UWB communication system and application in underground coal mines are introduced. The analyses show that, because of the transmission power being non-limitted in underground coal mines, the use of UWB in coal mines cannot only realize wireless access services of short distance high rate application for transmission of video monitoring signals, but also realize wireless access services of long distance low rate applications for mobile telephones in underground coal mines and parameters of working conditions monitoring, etc. It is emphasized on the simulation of a TH-PPM UWB communication system with traditional underground broadband model and ground CM1, CM3 model. It is shown that the traditional underground broadband model and ground CM1, CM3 models are not applicable to the UWB communication system in underground coal mines. It is necessary to conduct research on the propagation characteristics of UWB in coal mine tunnels, given the characteristics of the underground environment and to find the appropriate UWB model for underground coal mines.

Characterizing Ultra-wide Band indoor line-of-sight wireless channel

By exploring the deterministic characteristics of the measurement data, a new propagation model with two deterministic clusters and stochastic arriving rays within each cluster is proposed. When considering the cumulative distribution function （CDF） of the three key channel statistics, the proposed model fits the measurement data better than SV/IEEE 802.15.3, a model which is known as a standard model for UWB indoor propagation channel. Therefore, with the additional knowledge of the specific environment geometry, the proposed model generating impulse responses ＂resemble＂ the measured channel impulse responses better than IEEE model. Moreover, the proposed model＇s parameters obtaining procedure is simplified by utilizing simple parameters of the environment.

Impacts of Cumulus Momentum Transport on MJO Simulation

Vertical cumulus momentum transport is an important physical process in the tropical atmosphere and plays a key role in the evolution of the tropical atmospheric system. This paper focuses on the impact of the vertical cumulus momentum transport on Madden-Julian Oscillation （MJO） simulation in two global climate models （GCMs）. The Tiedtke cumulus parameterization scheme is applied to both GCMs [CAM2 and Spectral Atmospheric general circulation Model of LASG/IAP （SAMIL）]. It is found that the MJO simulation ability might be influenced by the vertical cumulus momentum transport through the cumulus parameterization scheme. However, the use of vertical momentum transport in different models provides different results. In order to improve model＇s MJO simulation ability, we must introduce vertical cumulus momentum transport in a more reasonable way into models. Furthermore, the coherence of the parameterization and the underlying model also need to be considered.

Evolution of dark solitons in the presence of Raman gain and self-steepening effect

Based on the equation satisfied by optical pulse that is a slowly varying function, the higher-order nonlinear Schr o¨dinger equation(NLSE) including Raman gain and self-steepening effect is deduced in detail, and a new Raman gain function is defined. By using the split-step Fourier method, the influence of the combined effect between Raman gain and self-steepening on the propagation characteristic of dark solitons is simulated in the isotropic fiber. The results show that gray solitons can be symmetrically formed by high order dark soliton, however self-steepening effect will inhibit the formation mechanism through the phenomenon that gray solitons are produced only in the trailing edge of the central black soliton. Meanwhile, the Raman gain changes the propagation characteristic of optical soliton and inhibits the self-steepening effect, resulting in the broadening of pulse width and the decreasing of pulse offset.

Constructions of new plateaued functions from known ones

A number of methods for constructing new plateaued functions from known ones are presented.Byproperly combining the known plateaued functions it is possible to get highly nonlinear resilient plateauedfunctions.The order,resiliency and propagation characteristics of the constructed plateaued functions arediscussed.We show the new functions could possess the desirable cryptographic property.

Solitary Wave Propagation Influenced by Submerged Breakwater

The form of Boussinesq equation derived by Nwogu （1993） using velocity at an arbitrary distance and surface elevation as variables is used to simulate wave surface elevation changes. In the numerical experiment, water depth was divided into five layers with six layer interfaces to simulate velocity at each layer interface. Besides, a physical experiment was carried out to validate numerical model and study solitary wave propagation.“Water column collapsing”method （WCCM） was used to generate solitary wave. A series of wave gauges around an impervious breakwater were set-up in the flume to measure the solitary wave shoaling, run-up, and breaking processes. The results show that the measured data and simulated data are in good agreement. Moreover, simulated and measured surface elevations were analyzed by the wavelet transform method. It shows that different wave frequencies stratified in the wavelet amplitude spectrum. Finally, horizontal and vertical velocities of each layer interface were analyzed in the process of solitary wave propagation through submerged breakwater.

Seismic reflection and transmission coeffi-cients at an air-water interface of saturated porous soil

Based on the modified Biot＇s theory of two-phase porous media, a study was presented on seismic reflection and transmission coefficients at an air-water interface of saturated porous soil media. The major differences between air-saturated soils and water-saturated soils were theoretically discussed, and the theoretical formulas of reflection and transmission coefficients at an air-water interface were derived. The characteristics of propagation and attenuation of elastic waves in air-saturated soils were given and the relations among the frequency, the angle of incidence and the reflection, transmission coefficients were analyzed by using numerical methods. Numerical results show that the propagation characteristic of the wave in air-saturated soils is great different from that in water-saturated soils. The frequency and the angle of incidence can have great influences on the reflection and transmission coefficients at interface. Some new cognition about the wave propagation is obtained and the study suggests that we may carefully pay attention to the influence of air on the dynamic analysis of seismic wave.

A crossed focused vortex beam with application to cold molecules

We report the generation of a crossed,focused,optical vortex beam by using a pair of hybrid holograms,which combine the vortex phase and lens phase onto a spatial light modulator.We study the intensity distributions of the vortex beam in free propagation space,and the relationship of its dark spot size with the incident Gaussian beam’s waist,the lens’s focal length,and its orbital angular momentum.Our results show that the crossed,focused,vortex beam’s dark spot size can be as small as 16.3μm and adjustable by the quantum number of the orbital angular momentum,and can be used to increase the density of trapped molecules.Furthermore,we calculate the optical potential of the blue-detuned,crossed vortex beam for MgF molecules.It is applicable to cool and trap neutral molecules by intensity-gradient-induced Sisyphus cooling,as the intensity gradient of such vortex beam is extremely high near the focal point.