The Information Protection in Automatic Reconstruction of Not Continuous Geophysical Data Series

We show a quantitative technique characterized by low numerical mediation for the reconstruction of temporal sequences of geophysical data of length L interrupted for a time ΔT where . The aim is to protect the information acquired before and after the interruption by means of a numerical protocol with the lowest possible calculation weight. The signal reconstruction process is based on the synthesis of the low frequency signal extracted for subsampling (subsampling &#8711Dirac = ΔT in phase with ΔT) with the high frequency signal recorded before the crash. The SYRec (SYnthetic REConstruction) method for simplicity and speed of calculation and for spectral response stability is particularly effective in the studies of high speed transient phenomena that develop in very perturbed fields. This operative condition is found a mental when almost immediate informational responses are required to the observation system. In this example we are dealing with geomagnetic data coming from an uw counter intrusion magnetic system. The system produces (on time) information about the transit of local magnetic singularities (magnetic perturbations with low spatial extension), originated by quasi-point form and kinematic sources (divers), in harbors magnetic underwater fields. The performances of stability of the SYRec system make it usable also in long and medium period of observation (activity of geomagnetic observatories).

Functional Design of A Series of Submerged Breakwaters for Coastal Protection Against Waves

The purpose of this paper is to develop a functional method for designing a series of submerged breakwaters on practical topography. The method is used to verify the feasibility and effectiveness of Bragg breakwaters for coastal protection by using field topography. The first part of this paper provides definitions and procedures needed in the design process for applying the mechanism of Bragg reflection. Next, Bragg breakwaters are designed on the basis of the cross-sectional topography and then on the plane topography of the Mi-Tuo coast by following the proposed process and procedure. Numerical modeling （Hsu et al., 2003; Wen and Tsai, 2008） was used as a design and assessment tool. Finally, the effectiveness and feasibility of a Bragg breakwater was assessed by practical cases. Based on the mechanism of Bragg reflection, an optimum layout for a series of submerged breakwaters is proposed to protect the Mi-Tuo coast. The results indicate that the proper layout of a series of submerged creakwaters can achieve the objective of beach protection.

Fuzzy Logic Controlled Dual Active Bridge Series Resonant Converter for DC Smart Grid Application

Over the last few years, smart grids have become a topic of intensive research, development and deployment across the world. This is due to the fact that, through the smart grid, stable and reliable power systems can be achieved. This paper presents a fuzzy logic control for dual active bridge series resonant converters for DC smart grid application. The DC smart grid consists of wind turbine and photovoltaic generators, controllable and DC loads, and power converters. The proposed control method has been applied to the controllable load＇s and the grid side＇s dual active bridge series resonant converters for attaining control of the power system. It has been used for management of controllable load＇s state of charge, DC feeder＇s voltage stability during the loads and power variations from wind energy and photovoltaic generation and power flow management between the grid side and the DC smart grid. The effectiveness of the proposed DC smart grid operation has been verified by simulation results obtained by using MATLAB and PLECS cards.

Erythropoietin reduces apoptosis of brain tissue cells in rats after cerebral ischemia/reperfusion injury:a characteristic analysis using magnetic resonance imaging

Some in vitro experiments have shown that erythropoietin （EPO） increases resistance to apoptosis and facilitates neuronal survival follow- ing cerebral ischemia. However, results from in vivo studies are rarely reported. Perfusion-weighted imaging （PWI） and diffusion-weighted imaging （DWI） have been applied successfully to distinguish acute cerebral ischemic necrosis and penumbra in living animals; therefore, we hypothesized that PWI and DWI could be used to provide imaging evidence in vivo for the conclusion that EPO could reduce apoptosis in brain areas injured by cerebral ischemia/reperfusion. To validate this hypothesis, we established a rat model of focal cerebral ischemia/ reperfusion injury, and treated with intra-cerebroventricular injection of EPO （5,000 U/kg） 20 minutes before injury. Brain tissue in the ischemic injury zone was sampled using MRI-guided localization. The relative area of abnormal tissue, changes in PWI and DWI in the ischemic injury zone, and the number of apoptotic cells based on TdT-mediated dUTP-biotin nick end-labeling （TUNEL） were assessed. Our findings demonstrate that EPO reduces the relative area of abnormally high signal in PWI and DWI, increases cerebral blood volume, and decreases the number of apoptotic cells positive for TUNEL in the area injured by cerebral ischemia/reperfusion. The experiment pro- vides imaging evidence in vivo for EPO treating cerebral ischemia/reperfusion injury.

Primary resonance of multiple degree-of-freedom dynamic systems with strong non-linearity using the homotopy analysis method

A homotopy analysis method（HAM）is presented for the primary resonance of multiple degree-of-freedom systems with strong non-linearity excited by harmonic forces.The validity of the HAM is independent of the existence of small parameters in the considered equation.The HAM provides a simple way to adjust and control the convergence region of the series solution by means of an auxiliary parameter.Two examples are presented to show that the HAM solutions agree well with the results of the modified Linstedt-Poincar＇e method and the incremental harmonic balance method.

Extrinsic electromagnetic fields, low frequency (phonon) vibrations, and control of cell function: a non-linear resonance system

Chou and Chen’s report in the 1970s suggested conformational protein adaptation (CPA) might be influenced by low frequency phonons acting as “a possible information system”. This report proposes the universal force of electromagnetism initiates the phonon system they cited as it per-turbs paramagnetic/diamagnetic dampers within the protein matrix to produce a quantized low frequency phonon signal series. (http://www.phy.ilstu.edu/~ren/phononsims/page3.html) The signal series is iteratively processed by the protein beta sub-unit, the system, to posi-tion the alpha sub-unit, the outcome, a classic non-linear resonance system resulting in con-formational protein adaptation (CPA). CPA “priming” enables a secondary ATP/redox driven power system to complete cell activity. The evolutionary appearance of these two systems reflects their hierarchy: 1) a low energy phonon driven information control circuit governed by principles of physics that, along with proteins, may have preceded planet earth, and 2), an ATP/redox power completion circuit directed by principles of chemistry that evolved in living systems 1 billion or more years after earth formed.

Piezoelectric resonant ice protection systems–Part1/2:Prediction of power requirement for de-icing a NACA 0024 leading edge

This paper proposes a numerical method to analyze the ice protection capability and predict the power requirements of a piezoelectric resonant de-icing system.The method is based on a coupled electro-mechanical finite element analysis which enables the fast computation of the modes of resonance of interest to de-ice curved surfaces and the estimation of the input voltage and current required for a given configuration(defined by its mode,actuator location,ice deposit,etc.).Eventually,the electric power to be supplied can be also assessed.The method is applied to a NACA 0024 leading edge equipped with piezoelectric actuators.First,two extension modes are analyzed and compared with respect to their efficiency and power requirements.Then,tests are carried out in an icing tunnel to verify the effectiveness of the piezoelectric ice protection system and the predictions of the maximal required power.The system allows de-icing the leading edge in less than 2 s for a glaze ice deposit.

Bifurcation analysis for an SMIB power system with series capacitor compensation associated with sub-synchronous resonance

In this paper,an introduction to the bifurcation theory and its applicability to the study of sub-synchronous resonance (SSR) phenomenon in power system are presented. The continuation and bifurcation analysis software AUTO97 is adopted to investigate SSR for a single-machine-infinite-bus power system with series capacitor compensation. The investigation results show that SSR is the result of unstable limit cycle after bifurcation. When the system exhibits SSR, some complex periodical orbit bifurcations, such as torus bifurcation and periodical fold bifurcation, may happen with the variation of limit cycle. Furthermore, the initial operation condition may greatly influence the ultimate state of the system. The time-domain simulation is carried out to verify the effectiveness of the results obtained from the bifurcation analysis.

Power supply for generating frequency-variable resonant magnetic perturbations on the J-TEXT tokamak

To further research the response of the tearing mode（TM） to dynamic resonant magnetic perturbation（DRMP） on the J-TEXT tokamak, a modified series resonant inverter power supply（MSRIPS） with a function of discrete variable frequency is designed for DRMP coils in this study. The MSRIPS is an AC–DC–AC converter, including a phase-controlled rectifier, an LC filter, an insulated gate bipolar transistor（IGBT） full bridge, a matching transformer, three resonant capacitors with different capacitance values, and three corresponding silicon controlled rectifier（SCR） switches. The function of discrete variable frequency is realized by switching over different resonant capacitors with corresponding SCR switches while matching the corresponding driving frequency of the IGBT full bridge. A detailed switching strategy of the SCR switch is put forward to obtain sinusoidal current waveform and realize current waveform smooth transition during frequency conversion. In addition, a resistor and thyristor bleeder is designed to protect the SCR switch from overvoltage. Manufacturing of the MSRIPS is completed, and the MSRIPS equipment can output current with an amplitude of 1.5 kA when its working frequency jumps among different frequencies. Moreover, the current waveform is sinusoidal and can smoothly transition during frequency conversion. Furthermore, the transition time when the current amplitude rises from zero to a steady state is less than 2 ms during frequency conversion. By using the MSRIPS, the expected discrete variable frequency DRMP is generated, and the phenomenon of the TM being locked to the discrete variable frequency DRMP is observed on the J-TEXT tokamak.

Quasicrystals’ Resonant Response with Translational Symmetry

Diffraction in quasicrystals is in logarithmic order and icosahedral point group symmetry. Neither of these features are allowed in Bragg diffraction, so a special theory is required. The present work displays exact agreement between the analytic metric with a numeric description of diffraction in quasicrystals that is based on quasi-structure factors. So far, we treated the hierarchic structure as ideal;now, we detail the theory by including two significant features: firstly, the steady state wave function of the incident radiation demonstrates how harmonics, in metrical space and time, enable coherent interaction between the periodic wave packet and hierarchic quasicrystal;secondly, mapping of the hierarchic structure for any influence of defects will allow estimation of possible error margins in the analysis. The hierarchic structure has the required logarithmic periodicity: superclusters, containing about 103 atoms, convincingly map phase contrast images;while higher orders leave space for subsidiary speculation. The diffraction is completely explained for the first time.

基于模态分析的多逆变器系统串并联谐振特性分析

基于模态分析的多逆变器系统谐振分析方法能够获得系统准确的谐振定位,但在谐振类型辨识方面存在不足。该文提出一种基于模态分析方法和参与因子计算的多逆变器系统谐振辨识方法。考虑线路阻抗,建立计及电容电流有源阻尼的逆变器诺顿等效模型。当逆变器组合变化时,对比串、并联谐振模态分析结果的差异。通过对系统谐振类型的划分,获取不同类型谐振的特征信息。针对不同类型谐振选择特定的模态分析方法,借助参与因子表现实现谐振类型辨识。最后,搭建仿真电路模型和实验平台,通过仿真和实验验证所得结论的正确性。

抑制分布式静止串联补偿器对线路保护影响的方法研究

分布式静止串联补偿器(distributed static series compensator,DSSC)通过调节注入线路的电压可改变线路功率,优化电网潮流分布。针对现有交流线路保护算法难以适应DSSC串入线路运行的问题,提出了抑制DSSC对线路保护影响的方法。首先,分析了DSSC对交流线路保护的影响,证明了DSSC注入电压可能改变距离保护的阻抗测量值,导致距离保护有拒动或误动的风险。然后,提出了利用DSSC本体过流保护快速将DSSC旁路、或基于故障辅助判据主动将DSSC注入电压降为0的方法,以抑制不同类型的线路故障时DSSC对线路保护的影响。最后,基于硬件在环RTDS实时仿真平台以及浙江湖州DSSC示范工程现场进行试验,验证了所提抑制DSSC对交流线路保护影响的方法的有效性。

基于SPWM的电磁流量计谐振式励磁系统研制

为了使电磁流量计长期可靠运行,需要降低励磁系统功耗并减少发热。因此,文中提出了一种基于SPWM控制的谐振式电磁流量计励磁控制方案,改变以往的恒流源驱动方式,采用高频开关电压源驱动,同时在励磁回路中串联电容来减少回路阻抗,并研制样机、开展实验验证。功耗测试结果表明:在相同励磁电流的条件下,所研制励磁系统功耗为原系统的58.3%,励磁电源功率为原系统的69.2%。水流量标定结果表明:当励磁频率为109.5 Hz时,所研制系统在水流速为0.5~5 m/s时标定精度满足0.5级要求。可见,所研制的励磁系统具有功耗低、测量精度高的特点。

基于等效电路模型的超声波电机串联谐振频率识别方法

在超声波电机运行过程中,由于负载、温升等因素的影响,电机的串联谐振频率会发生漂移。为了对电机进行精确控制,需要准确识别并跟踪电机的串联谐振频率。基于超声波电机的Butterworth-Van Dyke(BVD)等效电路模型,提出电机的串联谐振频率识别方法。利用电机端电压和端电流作为反馈信号,对反馈信号进行处理得到差分电压,进而得到电机端电压与差分电压的相位差,并分析了该相位差与串联谐振频率的关系。在此基础上,设计了相应的电路实现方案,制作了电路实物,采用所提出的方法对样机的串联谐振频率进行识别,并用阻抗分析仪测量了样机的串联谐振频率。结果表明:利用所提出的方法识别得到的串联谐振频率与试验测量得到的串联谐振频率相吻合,证明所提出的超声波电机串联谐振频率识别方法的准确性。

航空发动机电子控制器的高强辐射场干扰及防护

针对航空发动机电子控制器(EEC)易受高强辐射场(HIRF)干扰问题,以ZF-M600型EEC为研究对象,通过三维电磁仿真软件CST对EEC建模并进行平面波辐照仿真,模拟HIRF对EEC的干扰效应,仿真结果表明,HIRF可以通过孔缝耦合进入EEC内部并在腔体内部产生谐振,谐振频率处电场强度显著增加。依据RTCA DO-160G在400 MHz~4 GHz开展EEC辐射敏感度试验,试验结果表明:EEC失效频点为2.40 GHz和3.48 GHz,敏感模块为模拟量输入输出模块,敏感现象为模拟量数据丢失。EEC失效频点与谐振频率接近,说明EEC失效与腔体谐振有关,在EEC内部贴装吸波材料并进行仿真,分析吸波材料的放置方式和厚度对EEC谐振电磁干扰强度的影响,仿真结果表明,贴装吸波材料可以有效抑制谐振电磁干扰。

无线电能传输系统全桥逆变器性能优化研究

针对无线电能传输系统中全桥逆变器开关管的开通和关断存在振铃,能量传输波形纹波大,导致逆变器温升大和工作不稳定的问题,进行了电路建模分析,开展了全桥逆变器性能优化研究。首先,对逆变器开关管驱动电路进行了简化,建立了RLC串联谐振电路模型,分析了驱动电路结构参数对逆变器性能的影响规律,得出了优化方法;其次,分析了逆变器纹波大的问题,给出了优化方法;最后,搭建了300 W无线电能传输系统并进行实验。实验结果验证了优化方法的正确性和有效性,逆变器性能得到了改善,温升得到了有效控制,系统传输效率提高了5.3%,整机效率达到了89.3%。

电路参数对RLC串联谐振电路特性影响的实验研究

由于谐振电路具有良好的选择性,在通信与电子技术中得到了广泛的应用,串联谐振时电感电压或电容电压大于激励电压的现象在无线电通信技术领域获得了有效的应用。本文采用实验方法,通过保持电阻、电感不变,改变电容;保持电阻、电容不变,改变电感;保持电感、电容不变,改变电阻三种方式,研究了电容、电感、电阻等电路参数对RLC串联谐振电路特性的影响,得到电路谐振时谐振频率、通频带宽度、电感线圈等效电阻、品质因数随电感、电容、电阻变化的规律及不同元件参数对品质因数影响的不同机理。

电气化铁路“车-网”系统串/并联双模式宽频谐波扰动产生装置设计与测量方法

精确测量动车组与电力机车(简称机车)四象限变流器(four-quadrant converter,4QC)和牵引网的宽频带阻抗特性是识别电气化铁路“车-网”系统振荡和不稳定问题的重要途径。然而,已有研究采用单一电压/电流扰动注入方式对牵引网或机车4QC阻抗进行测量,可能造成部分谐波扰动流向非目标测量对象,导致被测对象的谐波扰动信噪比低,影响阻抗测量精度。因此,该文提出一种适用于电气化铁路“车-网”联合系统的串/并联双模式宽频谐波扰动产生装置与阻抗测量方法,装置具有电压和电流两种工作模式,可以发出频带为1~3000Hz的宽频谐波扰动。扰动产生装置拓扑主要由多绕组降压变压器、谐波功率放大单元、并联LC谐振电路和反串联绝缘栅双极晶体管(insulated gate bipolar transistor,IGBT)模块等部分构成,结合双闭环dq解耦控制和载波移相开环脉宽调制(pulse-width modulation,PWM)控制策略,实现频带双边可控、幅值可控且分布均匀的大功率谐波扰动输出。最后,利用MATLAB/Simulink仿真和RT-Lab硬件在环实验验证该文串/并联双模式宽频谐波扰动产生装置设计方案及阻抗测量方法的正确性与有效性。

基于改进下垂控制的多模块谐振变换器均衡控制策略研究

当前,光伏、海上风电等新能源场站的直流汇流应用得到越来越多的关注,在新能源发电低压输入中高压汇流输出的场合,为了提升直流输电电压并进一步减小器件应力,多采用输入并联输出串联(IPOS)结构。虽然这种模块化串并联结构有着许多优势,但由于模块间器件参数误差,导致各模块存在电压电流不均衡的问题,影响整个功率变换系统的稳定运行。为此提出了面向直流汇流应用的IPOS多模块谐振变换器的改进下垂控制均衡方法,各模块间无需加入通信就实现各模块的输出电压和功率的完全均衡,改进了传统下垂控制电压与参考值不符的问题,并进一步提升了系统的动态响应性能。基于该控制方式,搭建了三路模块化IPOS谐振变换器原理样机,通过实验验证了所提改进下垂控制方法对IPOS系统的均衡效果。