Despite the great potential of cellulose wood pulp and cellulose nanofibrils as reinforcing filler in thermoplastics,its use is limited due to its tendency to form agglomerates and due to its high hydrophilic characte...Despite the great potential of cellulose wood pulp and cellulose nanofibrils as reinforcing filler in thermoplastics,its use is limited due to its tendency to form agglomerates and due to its high hydrophilic character.Here we describe fiberboard composites with high contents of wood pulp or cellulose nanofibrils,and a resin of poly(styrene-methyl-methacrylate-acrylic acid)used as water-based emulsion.Cellulose wood pulp and cellulose nanofibrils were used directly in the form of water suspensions.The method is based on the flocculation of the polymer emulsion followed by agglomeration of a mixture of the polymer emulsion and cellulose suspension,leading to the co-precipitation of the composite material,which can be easily separated from the water phase.Composites with acrylic polymer/cellulose fibers in the proportions of 75:25,50:50 and 25:75 wt%were prepared.Composites were characterized by scanning electron microscopy(SEM),Fourier transform infrared spectroscopy(FTIR),thermogravimetric analysis(TGA),dynamic mechanical analysis(DMA)and water absorption tests.SEM analysis revealed a very good dispersion of the fibers without evidence of agglomeration,which led to superior mechanical properties.These results showed the effectiveness of the methodology and the potential of cellulose wood pulp and CNF as reinforcement fillers in fiberboard composites and any other high fiber-content materials.展开更多
SUMMARYThe purpose of this study was to evaluate basic density, chemical composition and fiber dimensions of ten Eucalyptus sp wood samples and verify the impact of this set of parameters and their combination on the ...SUMMARYThe purpose of this study was to evaluate basic density, chemical composition and fiber dimensions of ten Eucalyptus sp wood samples and verify the impact of this set of parameters and their combination on the Kraft pulping process yield and on bleached pulp quality. Ten eucalypt woods of different species, with basic densities varying from 365 to 544 kg/m3 and total wood carbohydrate contents varying from 70.0 to 74.5%, were transformed into kraft pulp of kappa number 17-18 and bleached to 90% ISO brightness by the sequence OD(PO)D. Wood basic density showed stronger correlations with fiber dimensions, pulping yield and pulp quality than did chemical composition. Lighter woods resulted in higher yields. However, wood specific consumption was lower for denser woods, even though these demanded more drastic pulping conditions to achieve a given kappa number. The pulp quality results suggest that lower density woods should be directed towards fabrication of refined paper (printing and writing grades) while the denser woods be directed to the sanitary papers segment (tissue grades).展开更多
Using 3-year-old culms of 8 provenances of Bambusa chungii from Guangdong, Guangxi and Hainan Provinces, the indexes of wood properties, such as fiber dimensions and chemical composition were investigated and analyzed...Using 3-year-old culms of 8 provenances of Bambusa chungii from Guangdong, Guangxi and Hainan Provinces, the indexes of wood properties, such as fiber dimensions and chemical composition were investigated and analyzed by the methods of Analysis of variance and correlation coefficient to reveal the geographic genetic variation situation. The results showed that there are significant differences be- tween fiber length, fibrin and 1% NaOH extraction contents of B. chungii from 8 provenances; moreover, the fiber length and fiber length/width ratio had a decreasing change pattern with geographic variation from the south to the north in altitude （from high to low in ele- vation）. The heritabilities for fibrin, fiber length, 1% NaOH extractive, lignin and fiber length/width ratio were 0.7, 0.84, 0.54, 0.38 and 0.13, respectively. A significant negative correlation was found between 1% NaOH extraction, benzo-alcohol extraction contents and bamboo culm yield, whereas there was a significant positive correlation between fibrin contents and bamboo wood yield. Besides, a close correlation was detected between fiber dimensions indices and bamboo growth or bamboo wood yield. Finally, three provenances with high qualities and culm yield, i.e. Huaiji, Xinyi and Guilin, were selected as superior sources based on principal component analysis.展开更多
研究了尾巨桉、巨尾桉、尾叶桉、蓝桉及小叶桉这5种桉木的材性特征及其预处理-碱性过氧化氢化学机械浆（P-RC APMP）制浆性能。结果表明：5种桉木的综纤维素质量分数在77.96%-81.36%之间,小叶桉最高,巨尾桉最低;木质素质量分数在23.18%-...研究了尾巨桉、巨尾桉、尾叶桉、蓝桉及小叶桉这5种桉木的材性特征及其预处理-碱性过氧化氢化学机械浆（P-RC APMP）制浆性能。结果表明：5种桉木的综纤维素质量分数在77.96%-81.36%之间,小叶桉最高,巨尾桉最低;木质素质量分数在23.18%-26.62%之间,尾叶桉的最高,巨尾桉最低;纤维平均长度在755-785μm之间,差异较小。采用P-RC APMP制浆方法,在H2O2用量5%,Na OH用量4.5%浸渍条件下,小叶桉的制浆得率最高,达86.7%,巨尾桉最低,仅为84.2%;在相同加拿大游离度（300 m L CSF）下,蓝桉浆的强度性能和光学性能最优,纸浆的抗张强度和白度分别达30.13（N·m）/g和82.5%（ISO）,且所需磨浆电耗最低,仅1 188 k Wh/t,巨尾桉浆的强度性能和光学性能最差,纸浆的抗张强度和白度分别为16.9（N·m）/g和73.8%（ISO）,且所需磨浆电耗最高,约为1 370 k Wh/t。展开更多
文摘Despite the great potential of cellulose wood pulp and cellulose nanofibrils as reinforcing filler in thermoplastics,its use is limited due to its tendency to form agglomerates and due to its high hydrophilic character.Here we describe fiberboard composites with high contents of wood pulp or cellulose nanofibrils,and a resin of poly(styrene-methyl-methacrylate-acrylic acid)used as water-based emulsion.Cellulose wood pulp and cellulose nanofibrils were used directly in the form of water suspensions.The method is based on the flocculation of the polymer emulsion followed by agglomeration of a mixture of the polymer emulsion and cellulose suspension,leading to the co-precipitation of the composite material,which can be easily separated from the water phase.Composites with acrylic polymer/cellulose fibers in the proportions of 75:25,50:50 and 25:75 wt%were prepared.Composites were characterized by scanning electron microscopy(SEM),Fourier transform infrared spectroscopy(FTIR),thermogravimetric analysis(TGA),dynamic mechanical analysis(DMA)and water absorption tests.SEM analysis revealed a very good dispersion of the fibers without evidence of agglomeration,which led to superior mechanical properties.These results showed the effectiveness of the methodology and the potential of cellulose wood pulp and CNF as reinforcement fillers in fiberboard composites and any other high fiber-content materials.
文摘SUMMARYThe purpose of this study was to evaluate basic density, chemical composition and fiber dimensions of ten Eucalyptus sp wood samples and verify the impact of this set of parameters and their combination on the Kraft pulping process yield and on bleached pulp quality. Ten eucalypt woods of different species, with basic densities varying from 365 to 544 kg/m3 and total wood carbohydrate contents varying from 70.0 to 74.5%, were transformed into kraft pulp of kappa number 17-18 and bleached to 90% ISO brightness by the sequence OD(PO)D. Wood basic density showed stronger correlations with fiber dimensions, pulping yield and pulp quality than did chemical composition. Lighter woods resulted in higher yields. However, wood specific consumption was lower for denser woods, even though these demanded more drastic pulping conditions to achieve a given kappa number. The pulp quality results suggest that lower density woods should be directed towards fabrication of refined paper (printing and writing grades) while the denser woods be directed to the sanitary papers segment (tissue grades).
文摘Using 3-year-old culms of 8 provenances of Bambusa chungii from Guangdong, Guangxi and Hainan Provinces, the indexes of wood properties, such as fiber dimensions and chemical composition were investigated and analyzed by the methods of Analysis of variance and correlation coefficient to reveal the geographic genetic variation situation. The results showed that there are significant differences be- tween fiber length, fibrin and 1% NaOH extraction contents of B. chungii from 8 provenances; moreover, the fiber length and fiber length/width ratio had a decreasing change pattern with geographic variation from the south to the north in altitude （from high to low in ele- vation）. The heritabilities for fibrin, fiber length, 1% NaOH extractive, lignin and fiber length/width ratio were 0.7, 0.84, 0.54, 0.38 and 0.13, respectively. A significant negative correlation was found between 1% NaOH extraction, benzo-alcohol extraction contents and bamboo culm yield, whereas there was a significant positive correlation between fibrin contents and bamboo wood yield. Besides, a close correlation was detected between fiber dimensions indices and bamboo growth or bamboo wood yield. Finally, three provenances with high qualities and culm yield, i.e. Huaiji, Xinyi and Guilin, were selected as superior sources based on principal component analysis.
文摘研究了尾巨桉、巨尾桉、尾叶桉、蓝桉及小叶桉这5种桉木的材性特征及其预处理-碱性过氧化氢化学机械浆（P-RC APMP）制浆性能。结果表明：5种桉木的综纤维素质量分数在77.96%-81.36%之间,小叶桉最高,巨尾桉最低;木质素质量分数在23.18%-26.62%之间,尾叶桉的最高,巨尾桉最低;纤维平均长度在755-785μm之间,差异较小。采用P-RC APMP制浆方法,在H2O2用量5%,Na OH用量4.5%浸渍条件下,小叶桉的制浆得率最高,达86.7%,巨尾桉最低,仅为84.2%;在相同加拿大游离度（300 m L CSF）下,蓝桉浆的强度性能和光学性能最优,纸浆的抗张强度和白度分别达30.13（N·m）/g和82.5%（ISO）,且所需磨浆电耗最低,仅1 188 k Wh/t,巨尾桉浆的强度性能和光学性能最差,纸浆的抗张强度和白度分别为16.9（N·m）/g和73.8%（ISO）,且所需磨浆电耗最高,约为1 370 k Wh/t。
