Experimental study on the effect of H_(2)O and O_(2) on the degradation of SF_(6) by pulsed dielectric barrier discharge

SF_(6) has excellent insulation performance and arc extinguishing ability,and is widely used in the power industry.However,its global warming potential is about 23,500 times that of C0_(2),it can exist stably in the atmosphere,it is not easily degradable and is of great potential harm to the environment.Based on pulsed dielectric barrier discharge plasma technology,the effects of H_(2)O and 0_(2) on the degradation of SF_(6) were studied.Studies have shown that H_(2)O can effectively promote the decomposition of SF_(6) and improve its degradation rate and energy efficiency of degradation.Under the action of a pulse input voltage and input frequency of 15 kV and 15 kHz,respectively,when H_(2)O is added alone the effect of 1% H_(2)O is the best,and the rate and energy efficiency of degradation of SF_(6) reach their maximum values,which are 91.9% and 8.25 g kWh^(-1),respectively.The synergistic effect of H_(2)O and O_(2) on the degradation of SF_(6) was similar to that of H_(2)O.When the concentration of H_(2)O and O_(2) was 1%,the system obtained the best rate and energy efficiency of degradation,namely 89.7% and 8.05 g kWh~(-1),respectively.At the same time,different external gases exhibit different capabilities to regulate decomposition products.The addition of H_(2)O can effectively improve the selectivity of S0_(2).Under the synergistic effect of H_(2)O and O_(2),with increase in O_(2) concentration the degradation products gradually transformed into SO_(2)F_(2).From the perspective of harmless treatment of the degradation products of SF_(6),the addition of O_(2) during the SF_(6) degradation process should be avoided.

Surface reactive species on MnO_x(0.4)-CeO_2 catalysts towards soot oxidation assisted with pulse dielectric barrier discharge

MnOx（0.4）-CeO2 was investigated for soot oxidation assisted with a pulse dielectric barrier discharge （DBD）. The catalysts were evaluated and characterized with TPO （temperature programmed oxidation）, X-ray diffraction （XRD）, Raman and X-ray photo- electron spectroscopy （XPS）. The ignition temperature Ti for soot oxidation decreased from 240.8 to 216.4 ℃ with the increase of the pulse DBD frequencies from 50 to 400 Hz, lower than that of the case without pulse DBD present （253.4 ℃）. The results of XRD, Raman and XPS agreed well with the TPO activities of MnOx（0.4）-CeO2 towards soot oxidation. More solid solution of ceria and manganese, and surface reactive species including 02 , O and Mn4＋ were responsible for the enhancement of soot oxidation due to pulse DBD injection in the present study. For solid solution favors to the activation and transformation of those species, which are be- lieved to be involved in the soot oxidation in a hybrid catalysis-plasma.

Effects of Oxygen Concentration on Pulsed Dielectric Barrier Discharge in Helium-Oxygen Mixture at Atmospheric Pressure

In this work the effects of O_2 concentration on the pulsed dielectric barrier discharge in helium-oxygen mixture at atmospheric pressure have been numerically researched by using a one-dimensional fluid model in conjunction with the chosen key species and chemical reactions.The reliability of the used model has been examined by comparing the calculated discharge current with the reported experiments. The present work presents the following significant results. The dominative positive and negative particles are He_2~＋ and O_2^-, respectively, the densities of the reactive oxygen species（ROS） get their maxima nearly at the central position of the gap, and the density of the ground state O is highest in the ROS. The increase of O_2 concentration results in increasingly weak discharge and the time lag of the ignition. For O_2 concentrations below 1.1%,the density of O is much higher than other species, the averaged dissipated power density presents an evident increase for small O_2 concentration and then the increase becomes weak. In particular,the total density of the reactive oxygen species reaches its maximums at the O_2 concentration of about 0.5%. This characteristic further convinces the experimental observation that the O_2 concentration of 0.5% is an optimal O_2/He ratio in the inactivation of bacteria and biomolecules when radiated by using the plasmas produced in a helium oxygen mixture.

Sterilization mechanism of helium/helium-oxygen atmospheric-pressure pulsed dielectric barrier discharge on membrane surface

Pulsed dielectric barrier discharge(PDBD) exhibits several applications in different fields;however,the interaction of its components with substances remains a key issue.In this study,we employed experimental and numerical modeling to investigate the interactions between different PDBD components and substances in pure helium and a helium-oxygen mixture.A membrane comprising a Staphylococcus aureus strain was utilized as the treatment object to demonstrate the trace actions of the evolutions and distributions of certain components on the surface of the substance.The results revealed that the shapes and sizes of the discharging area and inhibition zone differed between groups.Under a pure helium condition,a discharge layer existed along the membrane surface,lying beside the main discharging channel within the electrode area.Further,an annulus inhibition zone was formed at the outer edge of the electrode in the pure helium group at 30 s and 1 min,and this zone extended to a solid circle at 2 min with a radius that was~50% larger than that of the electrode radius.Nevertheless,the discharging channel and inhibition zone in the helium-oxygen mixture were constrained inside the electrode area without forming any annulus.A 2D symmetrical model was developed with COMSOL to simulate the spatiotemporal distributions of different particles over the membrane surface,and the result demonstrated that the main components,which formed the annulus inhibition zone under the pure helium condition,contributed to the high concentration of the He^(+)annulus that was formed at the outer edge of the electrode.Moreover,O^(+)and O_(2)^(+)were the main components that killed the bacteria under the helium-oxygen mixture conditions.These results reveal that the homogenization treatment on a material surface via PDBD is closely related to the treatment time and working gas.

Numerical investigation on the effect of gas parameters on ozone generation in pulsed dielectric barrier discharge

Pulsed dielectric barrier discharge is a promising technology for ozone generation and is drawing increasing interest. To overcome the drawback of experimental investigation, a kinetic model is applied to numerically investigate the effect of gas parameters including inlet gas temperature, gas pressure, and gas flow rate on ozone generation using pulsed dielectric barrier discharge. The results show that ozone concentration and ozone yield increase with decreasing inlet gas temperature, gas pressure, and gas flow rate. The highest ozone concentration and ozone yield in oxygen are about 1.8 and 2.5 times higher than those in air, respectively. A very interesting phenomenon is observed： the peak ozone yield occurs at a lower ozone concentration when the inlet gas temperature and gas pressure are higher because of the increasing average gas temperature in the discharge gap as well as the decreasing reduced electric field and electron density in the microdischarge channel. Furthermore, the sensitivity and rate of production analysis based on the specific input energy （SIE） for the four most important species 03, O, O（1D）, and O2（b1∑） are executed to quantitatively understand the effects of every reaction on them, and to determine the contribution of individual reactions to their net production or destruction rates. A reasonable increase in SIE is beneficial to ozone generation. However, excessively high S1E is not favorable for ozone production.

Particle Densities of the Atmospheric-Pressure Argon Plasmas Generated by the Pulsed Dielectric Barrier Discharges

Atmospheric-pressure argon plasmas have received increasing attention due to their high potential in many industrial and biomedical applications. In this paper, a 1-D fluid model is used for studying the particle density characteristics of the argon plasmas generated by the pulsed dielectric barrier discharges. The temporal evolutions of the axial particle density distributions are illustrated, and the influences of changing the main discharge conditions on the averaged particle densities are researched by independently varying the various discharge conditions. The calculation results show that the electron density and the ion density reach two peaks near the momentary cathodes during the rising and the falling edges of the pulsed voltage. Compared with the charged particle densities, the densities of the resonance state atom Arr and the metastable state atom Arm have more uniform axial distributions, reach higher maximums and decay more slowly. During the platform of the pulsed voltage and the time interval between the pulses, the densities of the excited state atom Ar＊ are far lower than those of the Arr or the Arm. The averaged particle densities of the different considered particles increase with the increases of the amplitude and the frequency of the pulsed voltage. Narrowing the discharge gap and increasing the relative dielectric constant of the dielectric also contribute to the increase of the averaged particle densities. The effects of reducing the discharge gap distance on the neutral particle densities are more significant than the influences on the charged particle densities.

The Effect of the Quartz Tube on the Appearance of Nanosecond Pulsed Discharge in Air

An experimental investigation of a nanosecond pulsed dielectric barrier discharge in atmospheric air is presented. In the setup a quartz tube was inserted between the cone and plane electrodes in the direction parallel to the electric field. It was shown that the appearance and property of the discharge were sensitive to the size and the position of the quartz tube. When the tube was placed on the grounded plane electrode, the discharge intensity was found to improve gradually with the increase in the diameter of the quartz tube. Furthermore, with an appropriate distance between the bottom edge of the quartz tube and the plane electrode, the discharge tended to exhibit better performance in generating homogeneous diffusive plasma. The possible mechanism is discussed.

Experimental study of an anti-icing method over an airfoil based on pulsed dielectric barrier discharge plasma

Aircraft icing has long been a plague to aviation for its serious threat to flight safety. Even though lots of methods for anti-icing have been in use or studied for quite a long time, new methods are still in great demand for both civil and military aircraft. The current study in this paper uses widely used Dielectric Barrier Discharge（DBD） plasma actuation to anti-ice on a NACA0012 airfoil model with a chord length of 53.5 cm in a closed-circuit icing wind tunnel. An actuator was installed at the leading edge of the airfoil model, and actuated by a pulsed low-temperature plasma power source. The actuator has two types of layout, a striped electrode layout and a meshy electrode layout.The ice accretion process or anti-icing process was recorded by a CCD camera and an infrared camera. Instantaneous pictures and infrared contours show that both types of DBD plasma actuators have the ability for anti-ice under a freestream velocity of 90 m/s, a static temperature of -7℃,an Median Volume droplet Diameter（MVD） of 20 lm, and an Liquid Water Content（LWC） of 0.5 g/m^3. The detected variations of temperatures with time at specific locations reveal that the temperatures oscillate for some time after spraying at first, and then tend to be nearly constant values.This shows that the key point of the anti-icing mechanism with DBD plasma actuation is to achieve a thermal equilibrium on the model surface. Besides, the power consumption in the anti-icing process was estimated in this paper by Lissajous figures measured by an oscilloscope, and it is lower than those of existing anti-icing methods. The experimental results presented in this paper indicate that the DBD plasma anti-icing method is a promising technique in the future.