Atmospheric transmission algorithm for pulsed X-rays from high-altitude nuclear detonations based on scattering correction

In high-altitude nuclear detonations,the proportion of pulsed X-ray energy can exceed 70%,making it a specific monitoring signal for such events.These pulsed X-rays can be captured using a satellite-borne X-ray detector following atmospheric transmission.To quantitatively analyze the effects of different satellite detection altitudes,burst heights,and transmission angles on the physical processes of X-ray transport and energy fluence,we developed an atmospheric transmission algorithm for pulsed X-rays from high-altitude nuclear detonations based on scattering correction.The proposed method is an improvement over the traditional analytical method that only computes direct-transmission X-rays.The traditional analytical method exhibits a maximum relative error of 67.79% compared with the Monte Carlo method.Our improved method reduces this error to within 10% under the same conditions,even reaching 1% in certain scenarios.Moreover,its computation time is 48,000 times faster than that of the Monte Carlo method.These results have important theoretical significance and engineering application value for designing satellite-borne nuclear detonation pulsed X-ray detectors,inverting nuclear detonation source terms,and assessing ionospheric effects.

Highly Defective Dark TiO_(2) Modified with Pt: Effects of Precursor Nature and Preparation Method on Photocatalytic Properties

The study focused on the modification with platinum of dark defective titania obtained via pulsed laser ablation. Both the method of Pt introduction and the nature of the Pt precursor were varied. All samples exhibited similar phase compositions, specific surface areas, and Pt contents. High-resolution transmission electron microscopy coupled with pulsed CO adsorption revealed increased dispersity when photoreduction and the hydroxonitrate complex (Me _(4) N) _(2) [Pt _(2) (OH) _(2) (NO _(3) ) _(8) ] were used. The sample featured a high content of single-atom species and subnano-sized Pt clusters. The X-ray photoelectron spectroscopy results showed that the photoreduction method facilitated the appearance of a larger number of Pt ^(2+) states, which appeared owing to the strong metal-support interaction (SMSI) eff ect of the transfer of electron density from the electron-saturated defects on the TiO _(2) surface to Pt ^(4+) . In the hydrogen evolution reaction, samples with a significant fraction of the Pt ^(2+) ionic component, capable of generating short-lived Pt^(0) single-atom sites under irradiation due to the SMSI eff ect, exhibited the highest photocatalytic activity. The 0.5Pt(C)/TiO_(2) -Ph sample exhibited the highest hydrogen yield with a quantum efficiency of 0.53, retaining its activity even after 8 h of operation.

Preparation of Highly Textured Bi and MnBi Films by the Pulsed Laser Deposition Method

Textured Bi and MnBi/Bi thin films are prepared by the pulsed laser deposition method. The highly c-axis textured MnBi films are obtained by annealing the bilayer consisting of textured Bi and Mn films. The eoercivities of the MnBi/Bi film are 1.5 T and 2.35 T at room temperature and at 373K, respectively, showing a positive temperature coefficient. Microstructural investigations show that the textured MnBi film results from the orientated growth induced by the textured Bi under-layer.

Design and Analysis of Terminal Guidance Law for Kinetic Interceptors based on Pulse Engine

A new terminal guidance law is proposed based on a solid propellant pulse engine and an improved proportional navigation method to address the terminal guidance issue for kinetic interceptors.On this basis,the start-stop curve of the pulse motor during the terminal guidance process is designed,along with its start-up logic.The effectiveness of the proposed guidance strategy is verified through simulation.

A numerical study of two-and three-dimensional detonation dynamics of pulse detonation engine by the CE/SE method

In this paper, the CE/SE method is developed to simulate the two- and three-dimensional flow-field of Pulse Detonation Engine (PDE). The conservation equations with stiff source terms for chemical reaction are solved in two steps. The detailed analysis of computational results of a PDE with a single detonation tube and a PDE with five detonation tubes are given in this paper. Complex wave systems are observed inside and outside a PDE. For a PDE with 5 detonation tubes, there is a big bow shock produced from a number of little shocks near the open ends of tubes. A lot of vortexes interact with shocks and a large expansion wave propagates forward and backward with respect to the PDE in a semi-oval shape.

Process Parameter Optimization of the Pulsed Current Argon Tungsten Arc Welding of Titanium Alloy

The selection of process parameters for obtaining optimal tensile properties in the pulsed current gas tungsten arc welding is presented. The tensile properties include ultimate tensile strength, yield strength and notch tensile strength. All these characteristics are considered together in the selection of process parameters by modified taguchi method to analyse the effect of each welding process parameter on tensile properties. Experimental results are furnished to illustrate the approach.

Adaptive split-step Fourier method for simulating ultrashort laser pulse propagation in photonic crystal fibres

In this paper, the generalized nonlinear Schrodinger equation （GNLSE） is solved by an adaptive split-step Fourier method （ASSFM）. It is found that ASSFM must be used to solve GNLSE to ensure precision when the soliton selffrequency shift is remarkable and the photonic crystal fibre （PCF） parameters vary with the frequency considerably. The precision of numerical simulation by using ASSFM is higher than that by using split-step Fourier method in the process of laser pulse propagation in PCFs due to the fact that the variation of fibre parameters with the peak frequency in the pulse spectrum can be taken into account fully.

Size transition of spiral waves using the pulse array method

The domain size of spiral waves is an important issue in studies of two-dimensional （2D） spatiotemporal patterns. In this work, we use the 2D complex Ginzburg-Landau equation （CGLE） as our model and find that an initially big spiral can successfully transfer to several small spirals by applying a pulse array method. The impacts of several important factors, such as array density, controlling intensity and pulsing time, are investigated. This control approach may be useful for the control of 2D spatiotemporal patterns and has potential applications in the control of some realistic systems, such as meteorological and cardiac systems.

Dynamic energy spectrum and energy deposition in solid target by intense pulsed ion beams

A method for analyzing the dynamic energy spectrum of intense pulsed ion beam(IPIB) was proposed.Its influence on beam energy deposition in metal target was studied with IPIB produced by two types of magnetically insulated diodes(MID).The emission of IPIB was described with space charge limitation model,and the dynamic energy spectrum was further analyzed with time-of-flight method.IPIBs generated by pulsed accelerators of BIPPAB-450(active MID) and TEMP-4M(passive MID) were studied.The dynamic energy spectrum was used to deduce the power density distribution of IPIB in the target with Monte Carlo simulation and infrared imaging diagnostics.The effect on the distribution and evolution of thermal field induced by the characteristics of IPIB dynamic energy spectrum was discussed.

A novel simulation method for positive corona current pulses

A novel two-dimensional （2D） simulation method of positive corona current pulses is proposed. A control-volume- based finite element method （CV-FEM） is used to solve continuity equations, and the Galerkin finite element method （FEM） is used to solve Poisson＇s equation. In the proposed method, photoionization is considered by adopting an exact Helmholtz photoionization model. Furthermore, fully implicit discretization and variable time step are used to ensure the time-efficiency of the present method. Finally, the method is applied to a positive rod-plane corona problem. The numerical results are in agreement with the experimental results, and the validity of the proposed method is verified.

Numerical study on the thermo-stress of ZrO_2 thermal barrier coatings by high-intensity pulsed ion beam irradiation

This paper studies numerically the thermo-mechanical effects of ZrO2 thermal barrier coatings （TBCs） irradiated by a high-intensity pulsed ion beam in consideration of the surface structure. Taking the deposited energy of ion beams in TBCs as the source term in the thermal conduction equation, the distribution of temperature in TBCs was simulated. Then, based on the distribution, the evolution of thermal stress was calculated by the finite element method. The results show that tensile radial stress formed at the valley of TBC surfaces after irradiation by HIPIB. Therefore, if cracks happen, they must be at valleys instead of peaks. As for the stress waves, no matter whether through peak or valley position, tensile and compressive stresses are present alternately inside TBCs along the depth direction, and the strength of stress decreases with time.

New methods to remove baseline drift in trapezoidal pulse shaping

Trapezoidal pulse shaping algorithm is widely applied to improve signal-to-noise ratio(SNR), throughput and energy resolution with the properties of noise suppression, pile-up pulse separation and ballistic deficit correction. The algorithm can be acquired by z transform method which is easier for derivation. However, the baseline drift of trapezoidal pulse appears because the noise superimposes on the input signal. In this paper,two new methods based on convergence analysis and noise suppression are proposed to remove the baseline drift resulting from trapezoidal pulse shaping. Simulations and experimental tests are carried out to verify the methods. The results demonstrate that the proposed methods can remove baseline drift in trapezoidal pulse shaping.

Numerical Study on the Two-Dimensional Temperature Fields of Titanium/Aluminum Double-Layer Target Irradiated by High-Intensity Pulsed Ion Beam

Interaction between high-intensity pulsed ion beam （HIPIB） and a double-layer target with titanium film on top of aluminum substrate was simulated. The two-dimensional nonlinear thermal conduction equations, with the deposited energy in the target taken as source term, were derived and solved by finite differential method. As a result, the two-dimensional spatial and temporal evolution profiles of temperature were obtained for a titanium/aluminum double-layer target irradiated by a pulse of HIPIB. The effects of ion beam current density on the phase state of the target materials near the film and substrate interface were analyzed. Both titanium and aluminum were melted near the interface after a shot when the ion beam current density fell in the range of 100 A/cm2 to 200 A/cm2.

Fast Remaining Capacity Estimation for Lithium-ion Batteries Based on Short-time Pulse Test and Gaussian Process Regression

It remains challenging to effectively estimate the remaining capacity of the secondary lithium-ion batteries that have been widely adopted for consumer electronics,energy storage,and electric vehicles.Herein,by integrating regular real-time current short pulse tests with data-driven Gaussian process regression algorithm,an efficient battery estimation has been successfully developed and validated for batteries with capacity ranging from 100%of the state of health(SOH)to below 50%,reaching an average accuracy as high as 95%.Interestingly,the proposed pulse test strategy for battery capacity measurement could reduce test time by more than 80%compared with regular long charge/discharge tests.The short-term features of the current pulse test were selected for an optimal training process.Data at different voltage stages and state of charge(SOC)are collected and explored to find the most suitable estimation model.In particular,we explore the validity of five different machine-learning methods for estimating capacity driven by pulse features,whereas Gaussian process regression with Matern kernel performs the best,providing guidance for future exploration.The new strategy of combining short pulse tests with machine-learning algorithms could further open window for efficiently forecasting lithium-ion battery remaining capacity.

Effects of synthetic conditions of pulse galvanostatic method on electroactivity of polyaniline

Nano-fibrous polyaniline was synthesized on stainless steel electrode in 0.5mol·L-1 H2SO4 solution by pulse galvanostatic method. The effects of synthetic conditions of pulse galvanostatic method on the electroactivity of polyaniline were investigated. The results show that the electroactivity of polyaniline film strongly depends on the synthetic conditions, such as the ratio of “on time” to “off time”(ton/toff), frequency, monomer concentration, temperature and mean current density. Different electroactivities of polyaniline are caused by different morphologies of polyaniline. The nano-fibrous polyaniline has higher electroactivity than polyaniline with other morphologies. Under the following conditions: mean current density of pulse galvanostatic method 13mA·cm-2, ton/toff 1, frequency 200Hz, monomer concentration 0.3mol·L-1 and temperature 20℃, nano-fibrous polyaniline film with the highest electroactivity can be obtained.

A Symplectic Method of Numerical Simulation on Local Buckling for Cylindrical Long Shells under Axial Pulse Loads

In this paper,the local buckling of cylindrical long shells is discussed under axial pulse loads in a Hamiltonian system.Using this system,critical loads and modes of buckling of shells are reduced to symplectic eigenvalues and eigensolutions respectively.By the symplectic method,the solution of the local buckling of shells can be employed to the expansion series of symplectic eigensolutions in this system.As a result,relationships between critical buckling loads and other factors,such as length of pulse load,thickness of shells and circumferential orders,have been achieved.At the same time,symmetric and unsymmetric buckling modes have been discuss.Moreover,numerical results show that modes of post-buckling of shells can be Bamboo node-type,bending type,concave type and so on.Research in this paper provides analytical supports for ultimate load prediction and buckling failure assessment of cylindrical long shells under local axial pulse loads.

Investigation of three-pulse photon echo in thick crystal using finite-difference time-domain method

This paper investigates the phenomenon of three-pulse photon echo in thick rare-earth ions doped crystal whose thickness is far larger than 0.002 cm which is adopted in previous works.The influence of thickness on the three-pulse photon echo＇s amplitude and efficiency is analyzed with the Maxwell-Bloch equations solved by finite-difference timedomain method.We demonstrate that the amplitude of three-pulse echo will increase with the increasing of thickness and the optimum thickness to generate three-pulse photon echo is 0.3 cm for Tm^（3＋）：YAG when the attenuation of the input pulse is taken into account.Meanwhile,we find the expression 0.09 exp（α＇L）,which is previously employed to describe the relationship between echo＇s efficiency and thickness,should be modified as 1.3 · 0.09 exp（2.4 ·α＇L） with the propagation of echo considered.

Process Parameters Optimization of an Aluminium Alloy with Pulsed Gas Tungsten Arc Welding (GTAW) Using Gas Mixtures

This paper demonstrates the enhancement of mechanical properties and effective optimization of pulsed GTAW process parameters on aluminium alloy 6061 using sinusoidal AC wave with argon plus helium gas mixtures. Modified Taguchi Method (MTM) was employed to formulate experimental layout and to study effect of process parameter optimization on mechanical properties of the weld joints. Microstructural characterization of weld joint was carried out to understand the structural property correlation with process parameters.

Optimizing pulsed current gas tungsten arc welding parameters of AA6061 aluminium alloy using Hooke and Jeeves algorithm

Though the preferred welding process to weld aluminium alloy is frequently constant current gas tungsten arc welding (CCGTAW),it resulted in grain coarsening at the fusion zone and heat affected zone(HAZ).Hence,pulsed current gas tungsten arc welding(PCGTAW) was performed,to yield finer fusion zone grains,which leads to higher strength of AA6061 (Al-Mg-Si) aluminium alloy joints.In order to determine the most influential control factors which will yield minimum fusion zone grain size and maximum tensile strength of the joints,the traditional Hooke and Jeeves pattern search method was used.The experiments were carried out based on central composite design with 31 runs and an algorithm was developed to optimize the fusion zone grain size and the tensile strength of pulsed current gas tungsten arc welded AA6061 aluminium alloy joints.The results indicate that the peak current (Ip) and base current (IB) are the most significant parameters,to decide the fusion zone grain size and the tensile strength of the AA6061 aluminum alloy joints.

Demagnetization Research on PMs in the Halbach Magnetized Pulsed Alternator

Demagnetization behavior of Halbach magnetized compensated pulsed alternator(CPA)is studied by using finite element method(FEM)under the different demagnetization factors in this paper.The effect of armature reaction magnetic field and thermal rise on demagnetization of PMs is analyzed.This paper investigates the effect of different demagnetization factors on magnetic field distribution,load current,and no-load phase voltage.A series of dynamic demagnetization points in Halbach array permanent magnet(PM)are evaluated to search the worst working point.Partial demagnetization risk can be represented by the worst working point,and the global demagnetization of the PM is represented by the no-load phase voltage characteristics after discharge.The research results demonstrated that the compensation shield with a certain thickness can increase the discharge current and weaken the demagnetization influence of armature reaction.The demagnetization effect of armature reaction on PMs at high temperatures will be strengthened.