Study on Chrome-free Purging Plugs for Steel Ladles

Purging plug refractories in China typically contain around 3 mass% of super-fine chromium oxide in the matrix in order to improve the performance of the purging plugs, primarily, slag corrosion and wear resistance. Alternatives to chromium oxide containing refractories have gained interest due to health concerns related to the formation of soluble chromium compounds over long storage periods of refractory wastes. Super-ground reactive alumina can replace chromium oxide in purging plug refractories and this paper discussed the new reactive alumina E-SY 88 in comparison to chromium oxide in a typical purging plug castable. The mixing behaviour, wet castable properties, as well as cured, dried, and fired properties at different temperatures up to 1 600 ℃ were compared. In addition, the hot modulus of rupture, creep behaviour, thermal shock resistance and slag corrosion resistance were tested. The microstructure after slag corrosion was investigated by SEM. The results prove that E-SY 88 is an economically viable technical alternative to chromium oxide in purging plug refractories.

Effects of Freeze/Thaw Cycles and Gas Purging Method on Polymer Electrolyte Membrane Fuel Cells

At subzero temperature, the startup capability and performance of polymer electrolyte membrane fuel cell (PEMFC) deteriorates markedly. The object of this work is to study the degradation mechanism of key components of PEMFC-membrane-electrode assembly (MEA) and seek feasible measures to avoid degradation. The effect of freeze/thaw cycles on the structure of MEA is investigated based on porosity and SEM measurement. The performance of a single cell was also tested before and after repetitious freeze/thaw cycles. The experimental results indicated that the performance of a PEMFC decreased along with the total operating time as well as the pore size distribution shifting and micro configuration changing. However, when the redundant water had been removed by gas purging, the performance of the PEMFC stack was almost resumed when it experienced again the same subzero temperature test. These results show that it is necessary to remove the water in PEMFCs to maintain stable performance under subzero temperature and gas purging is proved to be the effective operation.

Microstructure and physical properties of steel-ladle purging plug refractory materials

Three different castables were prepared as steel-ladle purging-plug refractory materials： corundum-based low-cement castable （C-LCC）, corundum-spinel-based low-cement castable （C-S-LCC）, and no-cement corundum-spinel castable （C-S-NCC） （hydratable alu- mina p-A1203 bonded）. The properties of these castables were characterized with regard to water demand/flow ability, cold crushing strength （CCS）, cold modulus of rupture （CMoR）, permanent linear change （PLC）, apparent porosity, and hot modulus of rupture （HMoR）. The re- sults show the CCS/CMoR and HMoR of C-LCC and C-S-LCC are greater than those of the castable C-S-NCC. According to the micro- structure analysis, the sintering effect and the bonding type of the matrix material differ among the three castables. The calcium hexaluminate （CA6） phase in the matrix of C-LCC enhances the cold and hot mechanical strengths. In the case of C-S-LCC, the CA6 and 2CaO·2MgO·14A12O3（C2MEA14） ternary phases generated from the matrix can greatly increase the cold and hot mechanical strengths. In the case of the no-cement castable, sintering becomes difficult, resulting in a lower mechanical strength.

PURGING OF BONE MARROWS CONTAMINATED WITH MYELOID LEUKEMIC CELLS BY INTERLEUKIN-2 AND LYMPHOKINE-ACTIVATED KILLER CELLS

The capability of recombinant human interleukin-2 ( rhIL-2) and lymphokine-activated killer (LAK) cells in the purging of normal human bone marrows contaminated with human myeloid leukemic cell lines was evaluated. Mixtures of normal human bone marrow mononuclear cells ( BMC) and K562 cells or HL-60 cells (at the BMCK562 ratio of 200:1, 100:1 or 20:1) were incubated with IL-2 with or without LAK cells at the BMC:LAK ratio of 1:1 for one or three days. The nubmers of residual K562 cells, BFU-E and CFU-GM were examined by clonogenic assays. In 200:1 mixture groups without LAK cells, the number of K562 colonies reduced by 50% with no loss of BFU-E and CFU-GM in one-day cultures, and no K562 colonies formed in three-day cultures with about 20% loss of BFU-E and CFU-GM. If the BMC.K562 ratios were 100:1 or 20:1 in the mktures, the leukemic cells could not be eliminated. When the mixtures were incubated with IL-2 and LAK cells, no leukemic cell colonies were detected in the 20:1 group following one-day

Numerical Simulation of Saline Intrusion and Purging in Long SeaOutfalls with Three-Dimensional Model

Saline intrusion into marine sewage ouffalls will greatly decrease the efficiency of sewage disposal. In order to investigate the mechanisms of this flow, in this paper, a three-dimensional numerical model based on FVM （Finite Volume Method） is established, The RNG κ-ε model is selected for turbulence modeling. The time-averaged vohtme fraction equations are introduced to simulate the stratification and inteffaeial exchange of sewage and seawater in outfalls. Validity of the established three-dimensional numerical model is evaluated by comparisons of numerical results with experimental data. With this three-dimensional numerical model, the internal flow characteristics in ouffalls for different sewage discharges are simulated. The results indicate that for a low sewage discharge, saline circulates in the outfall due to intrusion and both the inflowing momentum and the inteffaeial turbulent mixing are important mechanisms to extrude the saline. For a high sewage discharge, saline intrusion could be avoided. The inflow momentum is the main mechanism to extrude the saline and the inteffacial turbulent mixing is nut important relatively. Even at a high sewage discharge, the saline wedge would be retained in the main ouffall pipe after the risers are purged. It takes a long time for this saline wedge to be extruded by interracial turbulent mixing.

Progress and Developing Trend of Purging Plugs for Refining Ladle

Damage reasons of purging plugs for refining ladle and research progress on thermal shock resistance of corundum- spinel purging plugs were summarized. Research achievements and application results of nonoxides bonded corundum purging plugs for refining ladle were briefly reviewed. The further research and developing trend of purging plugs was proposed.

Hepatocytes isolated from neoplastic liver-immunomagnetic purging as a new source for transplantation

AIM： To investigate whether hepatocytes isolated from macroscopically normal liver during hepatic resection for neoplasia could provide a novel source of healthy hepatocytes, including the development of reliable protocols for malignant cells removal from the hepatocyte preparation. METHODS： Hepatocytes were procured from resected liver of 18 patients with liver tumors using optimised digestion and cell-enrichment protocols. Suspensions of various known quantities of the HT-29 tumor cell line and patient hepatocytes were treated or not with Ep-CAM-antibody-coated immunomagnetic beads in order to investigate the efficacy of tumor-purging by immunomagnetic depletion, using a semi-quantitative RT-PCR method developed to detect tumor cells. Immunomagnetic bead-treated or bead-untreated tumor cell-hepatocyte suspensions were transplanted intra-peritoneally in Balb/C nude mice to assess the rates of tumor development. RESULTS： Mean viable hepatocyte yield was 9.3×10^6 cells per gram of digested liver with mean viability of 70.5%. Immunomagnetic depletion removed tumor cells to below the RT-PCR detection-threshold of 1 tumor cell in 10^6 hepatocytes, representing a maximum tumor purging efficacy of greater than 400000-fold. Transplanted, immunomagnetic bead-purged tumor cell-hepatocyte suspensions did not form peritoneal tumors in Balb/C nude mice. Co-transplantation of hepatocytes with tumor cells did not increase tumorigenesis of the tumor cells. CONCLUSION： Immunomagnetic depletion appears to be an effective method of purging contaminating tumor cells to below threshold for likely tumorigenesis. Along with improved techniques for isolation of large numbers of viable hepatocytes, normal liver resected for neoplasia has potential as another clinically useful source of hepatocytes for transplantation.

PURGING OF ACUTE NON-LYMPHOCYTIC LEUKEMIA PROGENITORS BY PROCAINE AND HYPERTHERMIA

Procaine and hyperthermia have been shown to possess a relatively selective cytotoxicity to leukemlc cells. In this study, the combined effects of procaine and hyperthermia on the growth of hematopoietic progenitors (GM-CFU) and ieukemic progenitors (L-CFU) were examined to determine if this combination resulted in a great selective killing of leukemlc cells than that achieved by procaine or heat alone. When the cells were treated simutaneously with procaine (2 mM) and hyperthermia (42℃) for one hour, the killing of L-CFU was enhanced considerably whereas GM-CFU were not markedly affected. These data Indicate that the combined treatment with procain and hyperthermia might offer an efficient mean to selectively purge residual leukemlc cells in vitro. Procaine with hyperthermia may have a role in clinical autoiogous bone marrow transplantation for acute leukemia.

Optimization and Application of Corundum-spinel Purging Plugs for Refining Ladles

Corundum - spinel purging plugs were optimized through adjusting the formulation and the particle size composition of starting materials to prolong the service life of purging plugs for a 60 t refining ladle in a steel plant. Th.e optimized formulatioa is 30 mass% tabular corundum （6 - 3 mm ） , 20 mass% tabular corundum （3-1 ram）, 22 mass% tabular corundum （1 -0.5 ram） ＋ sintered spinel, 28% tabular corundum fines （0. 045 mm） ＋ fused spinel （0. 045 mm） ＋ bimodal α-Al2O3 micropowder ＋ Secar71 cement. The on-site results show that the plug can achieve an obviously long service life of 18 cycles, saving cost greatly.

Ongoing Technology and Developing Trend of Ar-blowing Purging Plug

An introduction of the ongoing technology of argon-blowing purging plugs in China was presented in this work. Gel powders were used as starting materials to enhance the high temperature mechanical properties of the purging plugs. Composite purging plug adopting extrusion formed gas-purging bar and slit had its surface structural design improved, which enhanced the resistances to thermal shock and molten steel penetration, prolonging the service life. In addition, the safety was greatly improved by upgrading the framework and production process, enhancing the resistance to breakout. It is indicated that the developing trend is to produce purging plugs of longer service life and better gas purging rate with different starting materials and structure designs to meet the requirements of various metallurgical processes.

Effects of Freeze/Thaw Cycles and Gas Purging Method on Polymer Electrolyte Membrane Fuel Cells

At subzero temperature, the startup capability and performance of polymer electrolyte membrane fuel cell PEMFC deteriorates markedly. The object of this work is to study the degradation mechanism of key compo- nents of PEMFC—membrane-electrode assembly MEA and seek feasible measures to avoid degradation. The ef- fect of freezethaw cycles on the structure of MEA is investigated based on porosity and SEM measurement. The performance of a single cell was also tested before and after repetitious freezethaw cycles. The experimental results indicated that the performance of a PEMFC decreased along with the total operating time as well as the pore size distribution shifting and micro configuration changing. However, when the redundant water had been removed by gas purging, the performance of the PEMFC stack was almost resumed when it experienced again the same subzero temperature test. These results show that it is necessary to remove the water in PEMFCs to maintain stable per- formance under subzero temperature and gas purging is proved to be the effective operation.

Effects of Nano-CaCO_(3)Addition on Properties of Corundum-based Dispersive Purging Plugs

In order to improve the properties of corundum based dispersive purging plugs,dispersive purging plug specimens were prepared using tabular corundum(1-0.15 and≤0.15 mm)as the aggregates,tabular corundum(≤0.044 mm)andα-Al_(2)O_(3)micropowder(d_(50)=0.6μm)as the matrix,Secar 71 cement as the binder,introducing different amounts of nano-CaCO_(3),casting into shapes,and firing at different temperatures(1200 or 1600℃)for 4 h.The effects of the nano-CaCO_(3) extra-addition(0,0.5%,1.0%,1.5%and 2.0%,by mass)on the consistency of the castables as well as the properties and microstructure of the dispersive purging plug specimens were studied.The results show that:(1)with the fixed water addition,the consistency of the corundum castables decreases as the nano-CaCO_(3)addition increases;(2)with the increasing nano-CaCO_(3)addition,the bulk density of the specimens fired at different temperatures for 4 h decreases,the apparent porosity,the cold strength and the hot modulus of rupture all increase,the gas permeability does not change significantly;(3)the specimens fired at 1600℃ for 4 h have obviously better cold comprehensive performance than those fired at 1200℃for 4 h;(4)when the nano-CaCO_(3)addition is 1.5%,the comprehensive performance of the specimen is the optimal.

Purging Plugs and Well Blocks for Refining Ladle

1 Scope This standard specifies the classification, technical requirements, test methods, inspection rules, marking, packing, transportation, storage and quality certificate of purging plugs and well blocks for refining ladle.

运用低温Purge降低LPCVD氮化硅工艺的微粒污染

LPCVD制备的氮化硅薄膜具有良好的阶梯覆盖性,但是这种薄膜的应力偏高,在石英工艺腔管使用到8μm后易形成剥落微粒。特别是半导体工艺发展到了亚微米阶段,这一问题对于产品良率的影响也越来越大。文中以垂直式LPCVD设备为研究对象,通过利用晶圆冷却时间,运用降低工艺腔体温度并使用N2Purge的方法来改善微粒状况。通过大量对比实验来得出最优温度设定。运用这种方式不但改善了LPCVD设备制备氮化硅膜的微粒状况,还延长了设备的维护周期,增加设备利用时间。

Application of response surface methodology for optimization of purge gas recycling to an industrial reactor for conversion of CO_2 to methanol

Nowadays, by the increasing attention to environment and high rate of fuel production, recycling of purge gas as reactant to a reactor is highly considered. In this study, it is proposed that the purge gases of methanol production unit, which are approximately15.018 t·h^(-1) in the largest methanol production complexes in the world, can be recycled to the reactor and utilized for increasing the production rate. Purge gas streams contain 63% hydrogen,20% carbon monoxide and carbon dioxide as reactants and 17% nitrogen and methane as inert. The recycling effect of beneficial components on methanol production rate has been investigated in this study. Simulation results show that methanol production enhances by recycling just hydrogen, carbon dioxide and carbon monoxide which is an effective configuration among the others. It is named as Desired Recycle Configuration(DRC) in this study. The optimum fraction of returning purge gas is calculated via one dimensional modeling of process and Response Surface Methodology(RSM) is applied to maximize the methanol flow rate and minimize the carbon dioxide flow rate. Simulation results illustrate that methanol flow rate increases by 0.106% in DRC compared to Conventional Recycle Configuration(CRC) which therefore shows the superiority of applying DRC to CRC.

THEORETICAL ANALYSIS OF USING AIRFLOW TO PURGE RESIDUAL WATER IN AN INCLINED PIPE

A refined theoretical analysis for using the spiral airflow and axial airflow to purge residual water in an inclined pipe was presented. The computations reveal that, in most cases, the spiral flow can purge the residual water in the inclined pipe indeed while the axial flow may induce back flow of the water, just as predicted in the experiments presented by Horii and Zhao et al. In addition, the effects of various initial conditions on water purging were studied in detail for both the spiral and axial flow cases.

PURGE OF MALIGNANT CELLS FROM BONE MARROW BY HEMATOPORPHYRIN DERIVATIVES AND LIGHT EXPOSURE IN VITRO

During autologous bone marrow graft in treatment of malignant diseases, it is critical to purge malignant cells from the marrow. In the present study, the sensitivity to photodynamic inactivation of 3 leukemic cell lines was compared with their counterpart normal hematopoietic cells. After mouse leukemic L1210 cells were treated with a preparation of hematoporphyrin derivatives, YHpD, 10 μg/ml for 1 hr. and irradiated with blacklight (peak wavelength 395 nm, light intensity 0.6 mW/cm2) for 5 minutes, the survival rate of clonogenic cells decreased to <10%, while that of bone marrow granulocyte macrophage progenitor cells (CFU-GM) in DBA/2 mice remained at nearly normal level (>80%). Similar results were obtained when human leukemic HL-60 cells were compared with human CFU-GM and mouse leukemic L615 cells with CFU-GM in 615 strain mice. It is suggested that hematoporphyrin photoradiation may be useful for Iselectively killing leukemic cells in bone marrow.

ANALYSIS OF PENTACHLOROPHENOL IN WATER BY PURGE AND TRAP CONCENTRATOR COUPLED TO GAS CHROMATOGRAPHY

It is convenient and time saving to analyze pentachlorophenol (PCP) in water by purge and trap concentrator coupled to gas chromatography that avoids employing a great deal of organic solvent. In this paper, the appropriate purge and trap conditions of PCP are determined: the trapped sorbent is TenaxGC; the purge gas is pure nitrogen and purge flow is 40ml/min; the purge time is 30min. A series of standard PCP water samples 5, 10, 50, 100, 200, 400, 800, 1000ppb are analyzed in order to obtain standard curve, and the linear regressive equation obtained is Y=109.65X-687.72, which correlation coefficient r is 0.9949. The precision of the method is determined with 0.5ppb PCP water sample, and the standard deviation measured is 3%. The detection limit for PCP is 0.2ppb.

肯天获得Ultra PurgeTM品牌，螺杆清洗料供应能力提高

肯天（全球领先的螺杆清洗料、脱摸剂和模具维护产品开发,生产和销售商）宣布已收购了Moulds Plus International的Ultra Purge、”清洗料业务包括Ultra PurgeTM品牌，产品和工艺技术．以及其他业务资产，

手性分子构象分析装置圆二色光谱仪的加强与改造

圆二色光谱仪是对手性分子进行构象分析和理化性质表征的重要仪器.然而长期高强度的使用会产生光谱仪光学元件劣化、检测器灵敏度降低等问题.通过优化分光系统的光学元件提升光传输效率,升级具有更高量子效率的大面积雪崩硅光电二极管检测器,进而大幅提高仪器信噪比,同时将测量波长范围从175~900 nm扩展到175~1150 nm.在氙灯被点燃之前用氮气彻底净化仪器,把氧气排除在光谱仪之外是非常重要的操作步骤.安装具有监视、计划、流量设置、报警和辅助控制等功能的活性氮监测系统,可以实时监测控制仪器内部氮气吹扫情况.通过升级改造,既加强了仪器的性能,又节省了氮气消耗成本,同时仪器使用寿命将进一步延长.