Effect of quenching and tempering processes on properties and microstructure of G115 steel

The novel martensitic heat-resistant steel G115 was designed for thick-section boiler components of ultra-supercritical(USC) power plants at 630-650 ℃.The impact of the quenching and tempering processes on the properties and microstructure of G115 steel was explored.The samples that were quenched and tempered twice had a higher tensile strength at room temperature and 650 ℃,and the impact energy was significantly improved.The strength and impact energy increased in proportion to the increase in the first quenching temperature.The microstructure differences between the single and double quenched and tempered samples were examined using metallographic microscopy and scanning electron microscopy.The grain size of the double quenched and tempered samples was finer than that of the single quenched and tempered samples, and the tempered martensite lath is more visible, as are the carbides and other precipitates, which are finer and more uniformly distributed.As the first quenching temperature increased, the grains became coarser but more uniform.

Application of the Controllable Quenching Technology to the Quenching and tempering Workpieces

In order to obtain the desired mechanical properties of quenching and tempering workpieces, as well as reduce the cracking tendency and distortion, a program of controllable quenching was established. Furthermore, a computer-aided quenching system (CAQ) was also developed. The application samples of the CAQ system showed satisfactory results.

Analysis of microstructure and performance of temper bead welded joints for SA508-3 steel by Quenching and Tempering mode

The HAZ microstructure and performance of Quenching and Tempering mode temper bead welding and general welded joints which were made on SA508-3 steel of 60 mm thickness were compared in this article. The result shows that tempering sorbite which has excellent overall performance was obtained in both modes. The microstructure of Quenching and Tempering mode welded joints got more fine grain. Even though the hardness of tempering bead welded joints is higher than the general one,it still meets the standards which is lower than 350 HV. The impact absorbing energy of each district of tempering bead welded joints HAZ reached 170 J,which is equal to general one.

Cold extrusion deformation behavior of medium carbon steel after quenching and tempering

By taking 40Cr as a specific object, cold extrusion deformation behavior of medium carbon steel after quenching and tempering was studied by experimental works. The influence of deformation extent (10%-50%), cone angle of die (90 °-120 °), hardness after quenching and tempering (HRC21-29) and lubricated condition on the forming load was analyzed. The results show that there is no central bursting and micro crack in the inner of the extruded specimen, and the forming quality is good. The double-peak phenomenon takes place at the front-end of the specimen; the double-peak index increases with deformation extent, and larger deformation can avoid the double-peak phenomenon. The deformation extent is the most important influencing factor, and the lubricated condition almost has no influence, which means that the phosphate coating plus soap process is still a proper lubrication method for cold extrusion of medium carbon steel after quenching and tempering. By investigating the microscopic structure before and after deformation, the initial equiaxed grain is elongated in the extrusion direction, and this feature is more significant at the front-end of specimen.

Numerical simulation research of dimension variation in heavy plate during quenching and tempering process

The dimension variation of B610E steel during the quenching and tempering process was simulated by ABAQUS,the coefficient of heat transfer during quenching was verified by the buried thermocouple test and the trend of the dimension variation during the quenching process was also calculated by ABAQUS. It was shown by the comparison of simulated results and industrially measured results that only the simulation of thickness and width variation was accurate, while length variation needed further simulation. Besides, the dimension variation trend was identical with the measured results.

Effect of low-temperature tempering on the mechanical properties of cold-rolled martensitic steel

Cold-rolled martensitic steel is an important type of advanced high-strength steel for automobile production.With martensite as its primary microstructure constituent, martensitic steel possesses exceptional high strength despite its low alloy content.As the strength of cold-rolled martensitic steel increases, the martensite and carbon content also increases, leading to a decrease in bending properties and toughness.In this paper, the effect of various tempering parameters on the bending property and impact toughness of a quenched cold-rolled martensitic steel sheet was studied.It is found that after quenching, the ductility and impact toughness of the experimental steel are improved using low-temperature heat treatment.The optimal tempering conditions for ductility and toughness are analyzed.

Effect of induction heating and tempering on properties and microstructures of quenched and tempered pipes

In this study,a C-Mn quenched steel tube was quickly tempered by induction heating,and the influence of the tempering temperature on its performance was studied and compared with that by traditional tempering. The results show that the yield strength of both is quite strong with regular changes in the tempering temperature,but that the tensile strength of the tube tempered by induction heating is higher than that tempered by traditional tempering by about 25 MPa,and the elongation after induction tempering is significantly higher than that after traditional tempering. The differences in the microstructures of tubes after induction and traditional tempering were compared by metallographic microscope,scanning electron microscopy,and transmission electron microscopy.Theoretical analysis was also performed. Compared with traditional tempering,a fine dispersion of precipitated carbides occurs after induction tempering,which is the main reason for the performance differences.

An Internal State Variable Model for the Low Temperature Tempering of Low Alloy Steels

An internal state variable (ISV) framework is used to predict the rate and degree of strain relaxation associated with the stage I, low temperature tempering of martensite. A single variable tracks the change in volume between the tempered an untempered structures. The rate at which this occurs is taken to be a function of martensite fraction, temperature, degree of tempering, and carbon concentration. Experimental dilatometty data is used to both fit and validate the model.

Effect of tempering temperature on microstructure and mechanical properties of high boron white cast iron

The effect of different tempering temperatures on the microstructure and mechanical properties of airquenched high boron white cast iron was studied.The results indicate that the high boron white cast iron comprises dendritic matrix and inter-dendritic M 2 B boride;and the matrix comprises martensite and pearlite.After quenching in the air,the matrix is changed into lath martensite;but only 1-μm-size second phase exists in the matrix.After tempering,another second phase of several tens of nanometers is found in the matrix,and the size and quantity increase with an increase in tempering temperature.The two kinds of second precipitation phase with different sizes in the matrix have the same chemical formula,but their forming stages are different.The precipitation phase with larger size forms during the austenitizing process,while the precipitation phase with smaller size forms during the tempering process.When tempered at different temperatures after quenching,the hardness decreases with an increase in the tempering temperature,but it increases a little at 450 ℃ due to the precipitation strengthening effect of the second phase,and it decreases greatly due to the martensite decomposition above 450 ℃.The impact toughness increases a little when tempered below 300 ℃,but it then decreases continuously owing to the increase in size and quantity of the secondary precipitate above 300 ℃.Considered comprehensively,the optimum tempering temperature is suggested at 300 ℃ to obtain a good combination of hardness and toughness.

Effect of inclusions on the formation of acicular ferrite in Ti-bearing non quenched-and-tempered steel

Nucleation of acicular ferrite and its influence factors in non quenched-and-tempered steel was studied by using TEM and thermodynamic calculation. The results show that the complex particles with a center made of Ti oxide, Al2O3, and silicate and an outside made of a small quantity of mixture of TiN and MnS are able to act as ferrite nucleation nuclei. The acicular ferrite percentage changes little with Ti. When the oxygen content was 80 ppm, the volume percentage of acicular ferrite decreased due to an increase in allotriomorphic ferrite. The larger the cooling rate and the shorter the incubation time, the finer the titanium oxide and the higher the nucleation ratio of acicular ferrite.

The Research and Application of Non-quenched and Tempered Steel 12Mn2VBS

In this paper, the study group has researched the comprehensive performance and application of the content of sulfur properly.Based on the research such a conclusion can be d non-quenched and tempered steel 12Mn2VBS made of 12Mn2VB by increasing the rawn: 12Mn2VBS the non-quenched and tempered steel has superior comprehensive performance to traditional quenched and tempered steel such as 45 and 40Cr,and it is the best material to manufacture automobile parts.

Research into Grinding Hardening of Microalloyed Non-quenched and Tempered Steel

Grinding hardening is a new technology of hardening steel piece surfaces with grinding heat generated in the grinding process instead of with a high or medium frequency induction heating method,which can effectively integrate grinding and surface hardening. Experimental studies were carried out on grinding hardening of non-quenched and tempered steel. Through grinding experiments with variable depths of cut and feeding rate,the variation in the depth of the hardening layer was studied and the microstructure of the hardening zone of the test pieces was subsequently ana-lyzed. In the end,the hardening effect of non-quenched and tempered steel was compared with that of 40Cr steel,which revealed the superiority of non-quenched and tempered steel in grinding hardening technology.

Rotating arc horizontal narrow gap welding of high strength quenched and tempered steel

Rotating arc borizontal narrow gap welding of quenched ＆ tempered （Q＆T） steel was innovatively performed for solving the bottleneck that the molten pool sagged due to the gravity. The shapely multilayer single pass horizontal joint could be obtairzed by using the rotating are welding process. The cold crack was not observed in the joint without controlling the heat input and selecting the consumables intentionally. Microstructure of the joint could be divided into three zones： base metal zone （BMZ） , heat-affected zone （ HAZ） and weld zone （WZ）. Because of the characteristic of the rotating arc horizontal welding process, the defects in the joints were slag inclztsion formed at the interlayer of lower side wall. Tbe tensile strength and hardness of HAZ and WZ were larger than those of BMZ. The impact toughness in WZ, HAZ and BM at 0 % is equal to 11.5, 212 and 236 J, respectively.

Plastic Deformation in Quench-and 650℃ Tempered Steel

The variations of the dislocation structures in the quench and 650℃ tempered steel with increase of elongations have been investigated by using transmission electron microscopy. In the small elongation stage, the boundaries between ferrite and carbide in this steel can release dislocations. As the elongations increase, the moving dislocations in the ferrite slip onto the carbides. Then, the interaction between moving dislocations and dislocations released from this boundaries, and the interaction between the dislocations moving to the carbides in every slip plane occurs. Thereby, the dislocation tangles around the carbides can be formed. In the large elongation stage, the dislocation tangles with high dislocation density and the developed dislocation cells are formed.

Laser Beam Welding of 600 MPa Quenched and Tempered High-Strength Steel

Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate and butt CO2 Laser Welding (LW) of 7 mm thick high-strength quenched and tempered low alloy SM570 (JIS) steel plates. The influence of laser welding parameters, mainly welding speed, defocusing distance and shielding gas flow rate on the weld profile, i.e., weld zone penetration depth and width, microstructure and mechanical properties of welded joints was determined. All welded joints showed smooth and uniform weld beads free from superficial porosity and undercuts. The selected best welding conditions were a laser power of 5.0 kW, welding speed of 500 mm/min, argon gas shielding flow rate of 30 L/min and a defocusing distance of -0.5 mm. It was observed that these conditions gave complete penetration and minimized the width of the weld bead. The microstructure of the welded joints was evaluated by light optical microscopy. The weld metal (WM) and heat-affected zone (HAZ) near weld metal achieved maximum hardness (355 HV). The tensile fractured samples showed the ductile mode of failure and ultimate tensile strength of 580 MPa.

Development of non-quenched and tempered bolt steel

The 8.8 grade non-quenched and tempered bolt steel was studied according to the process conditions of wire rod plant and customer requirments.Three types of experimental steel grades were selected.10MnSiTi Nb and 20Mn2VTi(N) were chosen as the formal steel after several experimemts.

淬回火工艺对N-Mo合金化Cr13型耐蚀塑料模具钢组织与力学性能的影响

对N-Mo合金化Cr13型耐蚀塑料模具钢进行925~1150℃保温0.5 h的油淬处理,再分别进行150~300℃保温2 h或者350~600℃保温1 h的回火处理,研究了淬回火工艺对该钢组织与力学性能的影响。结果表明:试验钢淬火后的组织主要为淬火马氏体,随着淬火温度的升高,晶粒长大,第二相逐渐固溶进基体,试验钢的硬度先增大后降低,当淬火温度为1050℃时,硬度达到峰值,为57.7 HRC,此时第二相基本固溶进基体,残余奥氏体体积分数仅为8.49%。随着回火温度的升高,试验钢组织由回火马氏体向索氏体转变,第二相逐渐析出并长大;硬度呈先降低后升高再迅速降低的趋势,冲击吸收能量随回火温度的变化规律与回火硬度的变化规律相反,抗拉强度的变化规律与硬度的变化规律一致,屈服强度呈先增大后降低的趋势,并在回火温度为480℃时达到最大值,为1445 MPa;在200℃以上温度回火后试验钢的塑性均保持在一个较好的水平。试验钢获得优异综合性能的热处理工艺为1050℃×0.5 h淬火+200~300℃×2 h回火,此时组织为回火马氏体,硬度为48~53 HRC,抗拉强度为1752~2050 MPa,屈服强度为1171~1223 MPa,冲击吸收能量为41~51 J,断面收缩率为42%~51%,断后伸长率为17.1%~17.7%。

07MnMoVR水电钢CCT曲线测定与应用

在Gleeble3800热模拟试验机上测定了07MnMoVR水电钢以不同冷却速度连续冷却时的膨胀曲线,结合金相-硬度法获得了该钢的静态CCT曲线,分析以不同冷却速度连续转变时的组织转变,阐明冷却速度与组织演变及硬度变化的关系。试验钢热处理工艺为920℃淬火,然后进行600℃回火时,力学性能满足生产技术要求。

770 MPa级调质铸钢液态金属致脆失效原因及相应防护对策

采用金相显微镜、电子扫描显微镜等对某大型截面铸钢工件裂纹成因进行了分析。结果表明:开裂高强度调质铸钢,在热浸锌过程中,基体产生了垂直于表面的裂纹,裂纹长度约为3 mm,且裂纹沿晶开裂。能谱结果表明,裂纹中富含大量锌,为典型的液态金属致脆现象。针对此情况,在热浸锌工艺、焊接工艺、成型工艺、涂装体系等方面给出了避免产生液态金属致脆的防护对策。

焊后热处理对DQTHT80钢热影响区断裂韧性的影响

研究了直接淬火回火调质钢ＤＱＴＨＴ８０多层焊热影响区的ＣＴＯＤ断裂韧性。焊态和焊后热处理状态下的试验结果表明：焊态下热影响区断裂韧性高于焊后热处理态。焊后热处理降低了该钢热影响区的断裂韧性。焊态下断口呈韧窝状，而焊后热处理断口呈解理状。模拟焊接热影响区粗晶区试验结果进一步证实了焊后热处理对韧性的不利影响。