Experimental studies of a model pump-turbine S-curve characteristics and its improvement by misaligned guide vanes （MGV） were extended to prototype pump turbine through 3-D transient flow simulations. The unsteady R...Experimental studies of a model pump-turbine S-curve characteristics and its improvement by misaligned guide vanes （MGV） were extended to prototype pump turbine through 3-D transient flow simulations. The unsteady Reynolds-averaged Navier-Stokes equations with the SST turbulence model were used to model the transient flow within the entire flow passage of a reversible pump-turbine with and without misaligned guide vanes during turbine model start-up. The unstable S-curve and its improvement by using misaligned guide vane were verified by model test and simulation. The transient flow calculations were used to clarify the variations of pressure pulse and internal flow behavior in the entire flow passage. The use of misaligned guide vanes can eliminate the S-curve characteristics of a pump-turbine, and can significantly increase the pressure pulse amplitude in the entire flow passage and the runner radial forces during start-up. The MGV only decreased the pulse amplitude on the guide vane suction side when the rotating speed was less than 50% rated speed. The hydraulic reason is that the MGV dramatically changed the flow patterns inside the entire flow passage, and destroyed the symmetry of the flow distribution inside the guide vane and runner.展开更多
Due to the pressure gain combustion characteristics,the rotating detonation combustor(RDC)can enhance thermodynamic cycle efficiency.Therefore,the performance of gas-turbine engine can be further improved with this co...Due to the pressure gain combustion characteristics,the rotating detonation combustor(RDC)can enhance thermodynamic cycle efficiency.Therefore,the performance of gas-turbine engine can be further improved with this combustion technology.In the present study,the RDC operation performance with a turbine guide vane(TGV)is experimentally investigated.Hydrogen and air are used as propellants while hydrogen and air mass flow rate are about 16.1 g/s and 500 g/s and the equivalence ratio is about 1.0.A pre-detonator is used to ignite the mixture.High-frequency dynamic pressure transducers and silicon pressure sensors are employed to measure pressure oscillations and static pressure in the combustion chamber.The experimental results show that the steady propagation of rotating detonation wave(RDW)is observed in the combustion chamber and the mean propagation velocity is above 1650 m/s,reaching over 84%of theoretical Chapman-Jouguet detonation velocity.Clockwise and counterclockwise propagation directions of RDW are obtained.For clockwise propagation direction,the static pressure is about 15%higher in the combustor compared with counterclockwise propagation direction,but the RDW dominant frequency is lower.When the oblique shock wave propagates across the TGV,the pressure oscillations reduces significantly.In addition,as the detonation products flow through the TGV,the static pressure drops up to 32%and 43%for clockwise and counterclockwise propagation process respectively.展开更多
The effect of clearance flow on the erosion characteristics of a circular cylinder with a backward facing step in sediment-laden water flow is analyzed numerically with the mixture model and the re-normalization group...The effect of clearance flow on the erosion characteristics of a circular cylinder with a backward facing step in sediment-laden water flow is analyzed numerically with the mixture model and the re-normalization group (RNG) k-ε turbulence model. Thirty-six monitoring points are set up on different stream surfaces to collect information on the impact erosion under different flow conditions, where the Initial Sediment Volume Fraction (ISVF) is set to 0.05, 0.075, 0.1, 0.125, and 0.15;particle diameter is set to 0.05 mm, 0.15 mm, 0.25 mm, 0.35 mm, and 0.45 mm respectively. The distribution of particle velocity and Local Solid-Phase Volume Fraction (LSVF) along different stream surfaces are calculated, based on which the trend of erosion is qualitatively evaluated. ISVF and particle diameter play different roles on the impact erosion index parameter () on the different wetted walls. Relative wear rate of numerical estimation agrees well with the practical one under the same working condition. Numerical analysis demonstrates that guide vane with a negative curvature end surface (concave surface) can decrease erosion damage effectively, which may provide a reference for optimal design and maintenance of hydraulic turbine.展开更多
This study presents endwall hydrodynamics and heat transfer in a linear turbine cascade at Re 5×105 at low and high intensities of turbulence.Results are numerically predicted using the standard SST model and Re...This study presents endwall hydrodynamics and heat transfer in a linear turbine cascade at Re 5×105 at low and high intensities of turbulence.Results are numerically predicted using the standard SST model and Reθ-γtransition model as well as using the high-resolution LES separately.The major secondary flow components,comprising the horseshoe,corner,and passage vortices are recognized and the impact on heat or mass transfer is investigated.The complicated behavior of turbine passage secondary flow generation and establishment are impacted by the perspective of boundary layer attributes and inflow turbulence.The passage vortex concerning the latest big leading-edge vane is generated by the enlargement of the circulation developed at the first instance adjacent to the pressure side becomes powerful and mixes with other vortex systems during its migration towards the suction side.The study conclusions reveal that substantial enhancements are attained on the endwall surface,for the entire spanwise blade extension on the pressure surface,and in the highly 3-D region close to the endwall on the suction surface.The forecasted suction surface thermal exchange depicts great conformity with the measurement values and precisely reproduces the enhanced thermal exchange owing to the development and lateral distribution of the secondary flows along the midspan of the blade passage downstream.The impacts of the different secondary flow structures on the endwall thermal exchange are described in depth.展开更多
To get the sustainable society, the hydropower with not only the large but also the small/mini/micro capacities has been paid attention to in the power generation. The cross flow turbine can work effectively at the co...To get the sustainable society, the hydropower with not only the large but also the small/mini/micro capacities has been paid attention to in the power generation. The cross flow turbine can work effectively at the comparatively low head and/or low discharge, then the runner and the turbine profile has been optimizing. In this paper, the model turbine was prepared in accordance with the traditional design, and the performance and the flow condition were investigated experimentally at the various operating conditions. The hydraulic efficiency is doubtlessly maximal while the guide vane is at the normal/design position, and deteriorates in the lower discharges adjusted by the guide vane. Such deteriorations are brought from the unacceptable flow conditions in the inlet nozzle. To improve the efficiency dramatically in the lower discharge, the guide vane installed in the inlet nozzle was equipped with the current plate, and the fruitful effects of the plate on the efficiency were confirmed experimentally.展开更多
Low-head hydraulic turbines are the subjects to individual approach of design. This comes from the fact that hydrological conditions are not of a standard character. Therefore, the design method of the hydraulic turbi...Low-head hydraulic turbines are the subjects to individual approach of design. This comes from the fact that hydrological conditions are not of a standard character. Therefore, the design method of the hydraulic turbine stage has a great importance for those who may be interested in such an investment. As a first task in a design procedure the guide vane is considered. The proposed method is based on the solution of the inverse problem within the flame of 2D model. By the inverse problem authors mean a design of the blade shapes for given flow conditions. In the paper analytical solution for the simple cylindrical shape of a guide vane is presented. For the more realistic cases numerical solutions according to the axis-symmetrical model of the flow are also presented. The influence of such parameters as the inclination of trailing edge, the blockage factor due to blade thickness, the influence of loss due to dissipation are shown for the chosen simple geometrical example.展开更多
Two concepts of the guide vanes channels design for a low head hydraulic turbine were investigated using 2D and 3D models. Model 2D was used to generate the geometry of profiles which form a blade channel. After that ...Two concepts of the guide vanes channels design for a low head hydraulic turbine were investigated using 2D and 3D models. Model 2D was used to generate the geometry of profiles which form a blade channel. After that by means of 3D commercial code （ANSYS/Fluent v. 15）, the designed cascades were examined. The characteristic parameters of compared guide vanes have been presented. The problem of low head hydraulic turbine design is important from the technical point of view for usually not typical environmental circumstances, in which the hydropower plants are planned.展开更多
Numerical simulations are carried out to investigate the effect of the endwall contouring on the secondary flow in turbine nozzle guide vane.The three contoured cascades with the same contouring profile and the differ...Numerical simulations are carried out to investigate the effect of the endwall contouring on the secondary flow in turbine nozzle guide vane.The three contoured cascades with the same contouring profile and the different positions where the contoured profile locates at are researched.The results show that the contouring configuration can reduce the aerodynamic losses of the cascade.The flat side takes advantage of a stronger decrease of the losses,compared to the contoured side.The contouring configuration can also inhibit the secondary flow.The contoured cascade in which the contouring profile starts upstream of the airfoil,ends at the middle of the airfoil has the best effect of improving secondary flow.展开更多
In this study, the goal is to increase the efficiency of a high-pressure hydraulic turbine. The goal is achieved by numerical flow simulation using CFX-TASCflow. This approach reduces costs and time compared to the ex...In this study, the goal is to increase the efficiency of a high-pressure hydraulic turbine. The goal is achieved by numerical flow simulation using CFX-TASCflow. This approach reduces costs and time compared to the experimental approach and allows for improving the turbine productivity and its design. The analysis of energy losses in the flow part of the turbine Fr500, as well as the analysis of the influence of the opening of the guide vanes on changes in energy losses. The results showed that the greatest losses occur in the guide vane 3.02% based on the two-dimensional model and 2.5% based on the 3D model, which significantly affects the efficiency. The analysis was carried out using programs for calculating fluid flow in two-dimensional and three-dimensional formulations. With the help of the study, the main energy problem is solved—increasing efficiency.展开更多
As the interaction between the combustor and the turbine in the aero-engine continues to increase,the film cooling design considering the combustor swirling outflow has become the research focus.The swirling inflow an...As the interaction between the combustor and the turbine in the aero-engine continues to increase,the film cooling design considering the combustor swirling outflow has become the research focus.The swirling inflow and high-temperature gas first affect the vane leading edge(LE).However,no practical improved solution for the LE cooling design has been proposed considering the combustor swirling outflow.In this paper,the improved scheme of showerhead cooling is carried out around the two ways of adopting the laid-back-fan-shaped hole and reducing the coolant outflow angle.The film cooling effectiveness(η) and the coolant flow state are obtained by PSP(pressure-sensitive-paint) and numerical simulation methods,respectively.The research results show that the swirling inflow increases the film distribution inhomogeneity by imposing the radial pressure gradient on the vane to make the film excessively gather in some positions.The showerhead film cooling adopts the laid-back-fan-shaped hole to reduce the momentum when the coolant flows out.Although this cooling scheme improves the film attachment and increases the surface-averaged film cooling effectiveness(η_(sur)) by as much as15.4%,the film distribution inhomogeneity increases.After reducing the coolant outlet angle,the wall-tangential velocity of the coolant increases,and the wall-normal velocity decreases.Under the swirl intake condition,both ηand the film distribution uniformity are significantly increased,and the growth of η_(sur) is up to 16.5%.This paper investigates two improved schemes to improve the showerhead cooling under the swirl intake condition to provide a reference for the vane cooling design.展开更多
Exhaust gas recirculation control(EGRC),an inlet air heating technology,can be utilized in combination with inlet/variable guide vane control(IGV/VGVC) and fuel flow control(FFC) to regulate the load,thereby effective...Exhaust gas recirculation control(EGRC),an inlet air heating technology,can be utilized in combination with inlet/variable guide vane control(IGV/VGVC) and fuel flow control(FFC) to regulate the load,thereby effectively improving the part-load(i.e.,off-design) performance of the gas turbine combined cycle(GTCC).In this study,the E-,F-,and H-Class EGR-GTCC design and off-design system models were established and validated to perform a comparative analysis of the part-load performance under the EGR-IGV-FFC and conventional IGV-FFC strategies in the E/F/H-Class GTCC.Results show that EGR-IGV-FFC has considerable potential for the part-load performance enhancement and can show a higher combined cycle efficiency than IGV-FFC in the E-,F-,and H-Class GTCCs.However,the part-load performance improvement in the corresponding GTCC was weakened for the higher class of the gas turbine because of the narrower load range of EGR action and the deterioration of the gas turbine performance.Furthermore,EGR-IGV-FFC was inferior to IGV-FFC in improving the performance at loads below 50% for the H-Class GTCC.The results obtained in this paper could help guide the application of EGR-IGV-FFC to enhance the part-load performance of various classes of GTCC systems.展开更多
Extensive experimental studies are performed using force sensors to measure actuating forces of nozzle ring devices of variable nozzle turbines. Torques from pneumatic action applied onto axles of nozzle vanes have be...Extensive experimental studies are performed using force sensors to measure actuating forces of nozzle ring devices of variable nozzle turbines. Torques from pneumatic action applied onto axles of nozzle vanes have been calculated. Test results obtained through repeated experiments are quite congruent, confirming the effectiveness of this simple method. Results have indicated that, with a fixed opening angle of guide vane, pneumatic torque increases with mass flow of air jet in the turbine; moreover, under the same mass flow rate, torque decreases with reducing opening angle, even possibly change direction down to negative. The results have also provided a modus operandi for designing nozzle-adjusting devices as well as validation data for numerical study on changes of pneumatic torque onto guide vanes under full engine operating conditions.展开更多
基金supported by the National Natural Science Foundation of China(51009077)State Key Laboratory of Hydroscience and Engineering(2014-KY-05)
文摘Experimental studies of a model pump-turbine S-curve characteristics and its improvement by misaligned guide vanes （MGV） were extended to prototype pump turbine through 3-D transient flow simulations. The unsteady Reynolds-averaged Navier-Stokes equations with the SST turbulence model were used to model the transient flow within the entire flow passage of a reversible pump-turbine with and without misaligned guide vanes during turbine model start-up. The unstable S-curve and its improvement by using misaligned guide vane were verified by model test and simulation. The transient flow calculations were used to clarify the variations of pressure pulse and internal flow behavior in the entire flow passage. The use of misaligned guide vanes can eliminate the S-curve characteristics of a pump-turbine, and can significantly increase the pressure pulse amplitude in the entire flow passage and the runner radial forces during start-up. The MGV only decreased the pulse amplitude on the guide vane suction side when the rotating speed was less than 50% rated speed. The hydraulic reason is that the MGV dramatically changed the flow patterns inside the entire flow passage, and destroyed the symmetry of the flow distribution inside the guide vane and runner.
基金the National Natural Science Foundation of China(No.11702143 and 11802137)the Fundamental Research Funds for the Central Universities(No.30918011343 and 30919011259).
文摘Due to the pressure gain combustion characteristics,the rotating detonation combustor(RDC)can enhance thermodynamic cycle efficiency.Therefore,the performance of gas-turbine engine can be further improved with this combustion technology.In the present study,the RDC operation performance with a turbine guide vane(TGV)is experimentally investigated.Hydrogen and air are used as propellants while hydrogen and air mass flow rate are about 16.1 g/s and 500 g/s and the equivalence ratio is about 1.0.A pre-detonator is used to ignite the mixture.High-frequency dynamic pressure transducers and silicon pressure sensors are employed to measure pressure oscillations and static pressure in the combustion chamber.The experimental results show that the steady propagation of rotating detonation wave(RDW)is observed in the combustion chamber and the mean propagation velocity is above 1650 m/s,reaching over 84%of theoretical Chapman-Jouguet detonation velocity.Clockwise and counterclockwise propagation directions of RDW are obtained.For clockwise propagation direction,the static pressure is about 15%higher in the combustor compared with counterclockwise propagation direction,but the RDW dominant frequency is lower.When the oblique shock wave propagates across the TGV,the pressure oscillations reduces significantly.In addition,as the detonation products flow through the TGV,the static pressure drops up to 32%and 43%for clockwise and counterclockwise propagation process respectively.
文摘The effect of clearance flow on the erosion characteristics of a circular cylinder with a backward facing step in sediment-laden water flow is analyzed numerically with the mixture model and the re-normalization group (RNG) k-ε turbulence model. Thirty-six monitoring points are set up on different stream surfaces to collect information on the impact erosion under different flow conditions, where the Initial Sediment Volume Fraction (ISVF) is set to 0.05, 0.075, 0.1, 0.125, and 0.15;particle diameter is set to 0.05 mm, 0.15 mm, 0.25 mm, 0.35 mm, and 0.45 mm respectively. The distribution of particle velocity and Local Solid-Phase Volume Fraction (LSVF) along different stream surfaces are calculated, based on which the trend of erosion is qualitatively evaluated. ISVF and particle diameter play different roles on the impact erosion index parameter () on the different wetted walls. Relative wear rate of numerical estimation agrees well with the practical one under the same working condition. Numerical analysis demonstrates that guide vane with a negative curvature end surface (concave surface) can decrease erosion damage effectively, which may provide a reference for optimal design and maintenance of hydraulic turbine.
文摘This study presents endwall hydrodynamics and heat transfer in a linear turbine cascade at Re 5×105 at low and high intensities of turbulence.Results are numerically predicted using the standard SST model and Reθ-γtransition model as well as using the high-resolution LES separately.The major secondary flow components,comprising the horseshoe,corner,and passage vortices are recognized and the impact on heat or mass transfer is investigated.The complicated behavior of turbine passage secondary flow generation and establishment are impacted by the perspective of boundary layer attributes and inflow turbulence.The passage vortex concerning the latest big leading-edge vane is generated by the enlargement of the circulation developed at the first instance adjacent to the pressure side becomes powerful and mixes with other vortex systems during its migration towards the suction side.The study conclusions reveal that substantial enhancements are attained on the endwall surface,for the entire spanwise blade extension on the pressure surface,and in the highly 3-D region close to the endwall on the suction surface.The forecasted suction surface thermal exchange depicts great conformity with the measurement values and precisely reproduces the enhanced thermal exchange owing to the development and lateral distribution of the secondary flows along the midspan of the blade passage downstream.The impacts of the different secondary flow structures on the endwall thermal exchange are described in depth.
文摘To get the sustainable society, the hydropower with not only the large but also the small/mini/micro capacities has been paid attention to in the power generation. The cross flow turbine can work effectively at the comparatively low head and/or low discharge, then the runner and the turbine profile has been optimizing. In this paper, the model turbine was prepared in accordance with the traditional design, and the performance and the flow condition were investigated experimentally at the various operating conditions. The hydraulic efficiency is doubtlessly maximal while the guide vane is at the normal/design position, and deteriorates in the lower discharges adjusted by the guide vane. Such deteriorations are brought from the unacceptable flow conditions in the inlet nozzle. To improve the efficiency dramatically in the lower discharge, the guide vane installed in the inlet nozzle was equipped with the current plate, and the fruitful effects of the plate on the efficiency were confirmed experimentally.
文摘Low-head hydraulic turbines are the subjects to individual approach of design. This comes from the fact that hydrological conditions are not of a standard character. Therefore, the design method of the hydraulic turbine stage has a great importance for those who may be interested in such an investment. As a first task in a design procedure the guide vane is considered. The proposed method is based on the solution of the inverse problem within the flame of 2D model. By the inverse problem authors mean a design of the blade shapes for given flow conditions. In the paper analytical solution for the simple cylindrical shape of a guide vane is presented. For the more realistic cases numerical solutions according to the axis-symmetrical model of the flow are also presented. The influence of such parameters as the inclination of trailing edge, the blockage factor due to blade thickness, the influence of loss due to dissipation are shown for the chosen simple geometrical example.
文摘Two concepts of the guide vanes channels design for a low head hydraulic turbine were investigated using 2D and 3D models. Model 2D was used to generate the geometry of profiles which form a blade channel. After that by means of 3D commercial code （ANSYS/Fluent v. 15）, the designed cascades were examined. The characteristic parameters of compared guide vanes have been presented. The problem of low head hydraulic turbine design is important from the technical point of view for usually not typical environmental circumstances, in which the hydropower plants are planned.
文摘Numerical simulations are carried out to investigate the effect of the endwall contouring on the secondary flow in turbine nozzle guide vane.The three contoured cascades with the same contouring profile and the different positions where the contoured profile locates at are researched.The results show that the contouring configuration can reduce the aerodynamic losses of the cascade.The flat side takes advantage of a stronger decrease of the losses,compared to the contoured side.The contouring configuration can also inhibit the secondary flow.The contoured cascade in which the contouring profile starts upstream of the airfoil,ends at the middle of the airfoil has the best effect of improving secondary flow.
文摘In this study, the goal is to increase the efficiency of a high-pressure hydraulic turbine. The goal is achieved by numerical flow simulation using CFX-TASCflow. This approach reduces costs and time compared to the experimental approach and allows for improving the turbine productivity and its design. The analysis of energy losses in the flow part of the turbine Fr500, as well as the analysis of the influence of the opening of the guide vanes on changes in energy losses. The results showed that the greatest losses occur in the guide vane 3.02% based on the two-dimensional model and 2.5% based on the 3D model, which significantly affects the efficiency. The analysis was carried out using programs for calculating fluid flow in two-dimensional and three-dimensional formulations. With the help of the study, the main energy problem is solved—increasing efficiency.
基金financial support from the National Natural Science Foundation of China (Grant No.U2241268)the Natural Science Foundation of Hunan Province (Grant No.2021JJ40646)+1 种基金the National Science and Technology Major Project(Grant No.J2019-Ⅲ-0019-0063)the Innovation Capacity Support Plan in Shaanxi Province of China (Grant No.2023-CX-TD-19)。
文摘As the interaction between the combustor and the turbine in the aero-engine continues to increase,the film cooling design considering the combustor swirling outflow has become the research focus.The swirling inflow and high-temperature gas first affect the vane leading edge(LE).However,no practical improved solution for the LE cooling design has been proposed considering the combustor swirling outflow.In this paper,the improved scheme of showerhead cooling is carried out around the two ways of adopting the laid-back-fan-shaped hole and reducing the coolant outflow angle.The film cooling effectiveness(η) and the coolant flow state are obtained by PSP(pressure-sensitive-paint) and numerical simulation methods,respectively.The research results show that the swirling inflow increases the film distribution inhomogeneity by imposing the radial pressure gradient on the vane to make the film excessively gather in some positions.The showerhead film cooling adopts the laid-back-fan-shaped hole to reduce the momentum when the coolant flows out.Although this cooling scheme improves the film attachment and increases the surface-averaged film cooling effectiveness(η_(sur)) by as much as15.4%,the film distribution inhomogeneity increases.After reducing the coolant outlet angle,the wall-tangential velocity of the coolant increases,and the wall-normal velocity decreases.Under the swirl intake condition,both ηand the film distribution uniformity are significantly increased,and the growth of η_(sur) is up to 16.5%.This paper investigates two improved schemes to improve the showerhead cooling under the swirl intake condition to provide a reference for the vane cooling design.
基金financial support from the Fundamental Research Project in the Chinese National Sciences and Technology Major Project (Grant No.2017-1-0002-0002)。
文摘Exhaust gas recirculation control(EGRC),an inlet air heating technology,can be utilized in combination with inlet/variable guide vane control(IGV/VGVC) and fuel flow control(FFC) to regulate the load,thereby effectively improving the part-load(i.e.,off-design) performance of the gas turbine combined cycle(GTCC).In this study,the E-,F-,and H-Class EGR-GTCC design and off-design system models were established and validated to perform a comparative analysis of the part-load performance under the EGR-IGV-FFC and conventional IGV-FFC strategies in the E/F/H-Class GTCC.Results show that EGR-IGV-FFC has considerable potential for the part-load performance enhancement and can show a higher combined cycle efficiency than IGV-FFC in the E-,F-,and H-Class GTCCs.However,the part-load performance improvement in the corresponding GTCC was weakened for the higher class of the gas turbine because of the narrower load range of EGR action and the deterioration of the gas turbine performance.Furthermore,EGR-IGV-FFC was inferior to IGV-FFC in improving the performance at loads below 50% for the H-Class GTCC.The results obtained in this paper could help guide the application of EGR-IGV-FFC to enhance the part-load performance of various classes of GTCC systems.
基金Sponsored by the National Natural Science Foundation of China (50676011)
文摘Extensive experimental studies are performed using force sensors to measure actuating forces of nozzle ring devices of variable nozzle turbines. Torques from pneumatic action applied onto axles of nozzle vanes have been calculated. Test results obtained through repeated experiments are quite congruent, confirming the effectiveness of this simple method. Results have indicated that, with a fixed opening angle of guide vane, pneumatic torque increases with mass flow of air jet in the turbine; moreover, under the same mass flow rate, torque decreases with reducing opening angle, even possibly change direction down to negative. The results have also provided a modus operandi for designing nozzle-adjusting devices as well as validation data for numerical study on changes of pneumatic torque onto guide vanes under full engine operating conditions.
