Single-phase-to-ground fault protection based on zero-sequence current ratio coefficient for low-resistance grounding distribution network

Definite-time zero-sequence over-current protection is presently used in systems whose neutral point is grounded by a low resistance(low-resistance grounding systems).These systems frequently malfunction owing to their high settings of the action value when a high-impedance grounding fault occurs.In this study,the relationship between the zero-sequence currents of each feeder and the neutral branch was analyzed.Then,a grounding protection method was proposed on the basis of the zero-sequence current ratio coefficient.It is defined as the ratio of the zero-sequence current of the feeder to that of the neutral branch.Nonetheless,both zero-sequence voltage and zero-sequence current are affected by the transition resistance,The influence of transition resistance can be eliminated by calculating this coefficient.Therefore,a method based on the zero-sequence current ratio coefficient was proposed considering the significant difference between the faulty feeder and healthy feeder.Furthermore,unbalanced current can be prevented by setting the starting current.PSCAD simulation results reveal that the proposed method shows high reliability and sensitivity when a high-resistance grounding fault occurs.

ANALYSIS OF TRANSMISSION CHARACTERISTICS OF COSINE GEAR DRIVE

Based on the mathematical model of a novel cosine gear drive, a few characteristics, such as the contact ratio, the sliding coefficient, and the contact and bending stresses, of this drive are analyzed. A comparison study of these characteristics with the involute gear drive is also carried out. The influences of design parameters including the number of teeth and the pressure angle on the contact and bending stresses are studied. The following conclusions are achieved： the contact ratio of the cosine gear drive is about 1.2 to 1.3, which is reduced by about 20% in comparison with that of the involute gear drive. The sliding coefficient of the cosine gear drive is smaller than that of the involute gear drive. The contact and bending stresses of the cosine gear drive are lower than those of the involute gear drive. The contact and bending stresses decrease with the growth of the number of teeth and the pressure angle.

A nonlinear interface structural damage model between ice crystal and frozen clay soil

The shear properties of ice-frozen soil interface are important when studying the constitutive model of frozen soil and slope stability in cold regions. In this research, a series of cryogenic direct shear tests for ice-frozen clay soil interface were conducted. Based on experimental results, a nonlinear interface structural damage model is proposed to describe the shear properties of ice-frozen clay soil interface. Firstly, the cementation and friction structural properties of frozen soil materials were analyzed, and a structural parameter of the ice-frozen clay soil interface is proposed based on the cryogenic direct shear test results. Secondly, a structural coefficient ratio is proposed to describe the structural development degree of ice-frozen clay soil interface under load, which is able to normalize the shear stress of ice-frozen clay soil interface,and the normalized data can be described by the Duncan-Chang model. Finally, the tangent stiffness of ice-frozen clay soil interface is calculated, which can be applied to the mechanics analysis of frozen soil. Also, the shear stress of ice-frozen clay soil interface calculated by the proposed model is compared with test results.

Reduction of chromium oxides in stainless steel dust

The recovery of metal oxides from stainless steel dust using C（graphite）, SiFe, and Al as reductants was investigated under various conditions. The apparent distribution ratio of Cr（L Cr ′^m/s ） in the recovered metal and residual slag phases was defined as the major performance metric. The results show that the recovery ratio of metals increases as the ratio of CaO ：SiO2 by mass in the residual slag increases to 1.17. The residual content of metals in the slag decreases as the Al2O3 content of the slag is increased from approximately 8wt% to 10wt%. The recovery ratio of Cr increases with increasing L Cr ′^ m/s , and a linear relationship between L Cr ′^m/s and the activity coefficient ratio of CrO in the slag and the recovered metal phase is observed. The combination of C and SiFe or Al as the reducing agents reveals that Si is the more effective coreductant.

Quantitative Diagnosis of Fault Severity Trend of Rolling Element Bearings

The condition monitoring and fault diagnosis of rolling element bearings are particularly crucial in rotating mechanical applications in industry. A bearing fault signal contains information not only about fault condition and fault type but also the severity of the fault. This means fault severity quantitative analysis is one of most active and valid ways to realize proper maintenance decision. Aiming at the deficiency of the research in bearing single point pitting fault quantitative diagnosis, a new back-propagation neural network method based on wavelet packet decomposition coefficient entropy is proposed. The three levels of wavelet packet coefficient entropy（WPCE） is introduced as a characteristic input vector to the BPNN. Compared with the wavelet packet decomposition energy ratio input vector, WPCE shows more sensitive in distinguishing from the different fault severity degree of the measured signal. The engineering application results show that the quantitative trend fault diagnosis is realized in the different fault degree of the single point bearing pitting fault. The breakthrough attempt from quantitative to qualitative on the pattern recognition of rolling element bearings fault diagnosis is realized.

Steady-State Visual Evoked Potential (SSVEP) in a New Paradigm Containing Dynamic Fixation Points

Steady-state visual evoked potential(SSVEP)has become a powerful tool for Brain Computer Interface(BCI)because of its high signal-tonoise ratio,high information transmission rate,and minimal user training.At present,the edge information of each region cannot be identified in spatial coding based on SSVEP-BCI technology,and the user experience is poor.To solve this problem,this paper designed a new paradigm to explore the relationship between the fixation point position of continuous sliding and the correlation coefficient ratio in the dualfrequency case.Firstly,the standard sinusoidal signal was employed to simulate the Electroencephalogram(EEG)signal,which verified the reliability of characterizing the amplitude variation of test signal by correlation coefficient.Then,the relationship between the amplitude response of SSVEP and the distance between the fixation point and the stimulus in the horizontal direction was tested by Canonical Correlation Analysis(CCA)and Filter bank CCA(FBCCA).Finally,the experimental data were offline analyzed under the condition of continuous sliding of the fixation point.It is feasible and reasonable to detect the amplitude change of frequency component in SSVEP by utilizing the spatial coding method in this paper to improve the extraction accuracy of spatial information.

Estimation of ballistic coefficients of space debris using the ratios between different objects

This paper proposes a new method to estimate the ballistic coefficient（BC） of low earth orbit space debris.The data sources are the historical two-line elements（TLEs）.Since the secular variation of semi-major axes is mainly caused by the drag perturbation for space objects with perigee altitude below 600 km,the ballistic coefficients are estimated based on variation of the mean semi-major axes derived from the TLEs.However,the approximate parameters used in the calculation have error,especially when the upper atmosphere densities are difficult to obtain and always estimated by empirical model.The proportional errors of the approximate parameters are cancelled out in the form of ratios,greatly mitigating the effects of model error.This method has been also been validated for space objects with perigee altitude higher than 600 km.The relative errors of estimated BC values from the new method are significantly smaller than those from the direct estimation methods used in numerical experiments.The estimated BC values are used for the prediction of the semi-major axes,and good performance is obtained.This process is also a feasible method for prediction over a long period of time without an orbital propagator model.

Novel high-PSRR high-order curvature-compensated bandgap voltage reference

This paper proposes a novel high-power supply rejection ratio（high-PSRR） high-order curvature-compensated CMOS bandgap voltage reference（BGR） in SMIC 0.18 μm CMOS process. Three kinds of current are added to a conventional BGR in order to improve the temperature drift within wider temperature range, which include a piecewise-curvaturecorrected current in high temperature range, a piecewise-curvature-corrected current in low temperature range and a proportional-to-absolute-temperature T^（1.5） current. The high-PSRR characteristic of the proposed BGR is achieved by adopting the technique of pre-regulator. Simulation results shows that the temperature coefficient of the proposed BGR with pre-regulator is 8.42x10^（-6）′ /℃ from - 55 ℃ to 125 ℃ with a 1.8 V power supply voltage. The proposed BGR with pre-regulator achieves PSRR of - 123.51 dB, - 123.52 dB, - 88.5 dB and - 50.23 dB at 1 Hz, 100 Hz, 100 kHz and 1 MHz respectively.