Variable precipitation behaviors of Laves phases in an ultralight Mg-Li-Zn alloy

Precipitation habits plays a decisive role in strengthening materials,especially for Mg alloys the non-basal plane precipitation is necessary but very limited.Generally,the precipitates would nucleate and grow up in a specific habit plane owing to the constraint of free-energy minimization of the system.Herein,in an aged ultralight Mg-Li-Zn alloy,we confirmed that the precipitates dominated by C15 Laves structure could form in a variety of habit planes,to generate three forms of strengthening-phases,i.e.,precipitate-rod,precipitate-lath,and precipitate-plate.Among which,the precipitate-plates are on basal plane as usually but precipitate-rods/laths are on non-basal plane,and such non-basal precipitates would transform into the basal(Mg,Li)Zn_(2)Laves structure with prolonged aging.These findings are interesting to understand the precipitation behaviors of multi-domain Laves structures in hexagonal close-packed crystals,and expected to provide a guidance for designing ultralight high-strength Mg-Li based alloys via precipitation hardening on the non-basal planes.

Quantitative Precipitation Estimation Using X-band Phased Array Weather Radar

This study utilized data from an X-band phased array weather radar and ground-based rain gauge observations to conduct a quantitative precipitation estimation(QPE)analysis of a heavy rainfall event in Xiong an New Area from 20:00 on August 21 to 07:00 on August 22,2022.The analysis applied the Z-R relationship method for radar-based precipitation estimation and evaluated the QPE algorithm s performance using scatter density plots and binary classification scores.The results indicated that the QPE algorithm accurately estimates light to moderate rainfall but significantly underestimates heavy rainfall.The study identified disparities in the predictive accuracy of the QPE algorithm across various precipitation intensity ranges,offering essential insights for the further refinement of QPE techniques.

Precipitation of metastable phases and its effect on electrical resistivity of Al-0.96Mg_2Si alloy during aging

The precipitation behavior and its influence on the electrical resistivity of the Al-0.96Mg2Si alloy during aging were investigated with in-situ resistivity measurement and transmission electron microscopy （TEM）. The precipitates of the peak aged alloy include both β＂ and if, but the amount ratio of β＂ to β＂ varies with the aging temperature and time increasing. The precipitates during aging at 175 ℃ are dominated by needle-like β＂ phases （including pre-β＂ phase）, the size of which increases with the time prolonging, but does not increase substantially after further aging. The evolution of electrical conductivity is directly related to such microstructural evolution. However, the hardness of the alloy stays at the peak value for a long term. When the alloy is aged at 195 ℃, the ratio of β＂ to β＇ becomes the main factor to influence relative resistivity （Ap） value. The higher the temperature is, the smaller the ratio is, and the faster the Ap value decreases. Moreover, the hardness peak drops with the decrease of the ratio. With the size and distribution parameters measured from TEM images, a semi-quantitative relationship between precipitates and the electrical resistivity was established.

Secondary phase precipitate-induced localized corrosion of pure aluminum anode for aluminum–air battery

Understanding the influence of purities on the electrochemical performance of pure aluminum(Al)in alkaline media for Al–air batteries is significant.Herein,we comprehensively investigate secondary phase precipitate(SPP)-induced localized corrosion of pure Al in NaOH solution mainly based on quasi-in-situ and cross-section observations under scanning electron microscopy coupled with finite element simulation.The experimental results indicate that Al–Fe SPPs appear as clusters and are coherent with the Al substrate.In alkaline media,Al–Fe SPPs exhibit more positive potentials than the substrate,thus aggravating localized galvanic corrosion as cathodic phases.Moreover,finite element simulation indicates that the irregular geometry coupled with potential difference produces the non-uniform current density distribution inside the SPP cluster,and the current density on the Al substrate gradually decreases with distance.

Assessing the predictive capabilities of precipitation strengthening models for deformation twinning in Mg alloys using phase-field simulations

Precipitation strengthening is a key strategy for improving the overall mechanical properties of Mg alloys. In Mg-Al alloys, basal precipitates are known to strengthen against twinning, resulting in an increase in the critical resolved shear stress(CRSS) necessary for continued deformation. Although several models have been proposed to quantify the influence of precipitate shape, size, and distribution on the CRSS, the accuracy, scope, and applicability of these models has not been fully assessed. Accordingly, the objectives of this study are:(i)to analyze the accuracy of analytical models proposed in the literature for precipitation strengthening against twin thickening and propagation(in Mg-Al alloys) using phase-field(PF) simulations,(ii) to propose modifications to these model forms to better capture the observed trends in the PF data, and(iii) to subsequently test the predictiveness of the extended models in extrapolating to experimental strengthening data.First, using an atomistically-informed phase-field method, the interactions between migrating twin boundaries(during the propagation and thickening stages) and basal plates are simulated for different precipitate sizes and arrangements. In general, comparison of the increase in CRSS determined from the PF simulations and the predictions from four precipitation strengthening models reveals that modifications are necessary to the model forms to extend their applicability to precipitation strengthening against both twin thickening and propagation. A subsequent comparison between predictions from the extended models and experimental strengthening data for peak age-hardened samples reveals that the(extended) single dislocation and dislocation wall models provide reasonably accurate values of the increase in CRSS.Ultimately, the results presented here help elucidate the fidelity and applicability of the various hardening models in predicting precipitation strenghtening effects in technologically important alloys.

A novel immiscible high entropy alloy strengthened via L1_(2)-nanoprecipitate

The low-cost Fe-Cu,Fe-Ni,and Cu-based high-entropy alloys exhibit a widespread utilization prospect.However,these potential applications have been limited by their low strength.In this study,a novel Fe_(31)Cu_(31)Ni_(28)Al_(4)Ti_(3)Co_(3) immiscible high-entropy alloy(HEA)was developed.After vacuum arc melting and copper mold suction casting,this HEA exhibits a unique phase separation microstructure,which consists of striped Cu-rich regions and Fe-rich region.Further magnification of the striped Cu-rich region reveals that it is composed of a Cu-rich dot-like phase and a Fe-rich region.The aging alloy is further strengthened by a L1_(2)-Ni_(3)(AlTi)nanoprecipitates,achieving excellent yield strength(1185 MPa)and uniform ductility(~8.8%).The differential distribution of the L1_(2) nanoprecipitate in the striped Cu-rich region and the external Fe-rich region increased the strength difference between these two regions,which increased the strain gradient and thus improved hetero-deformation induced(HDI)hardening.This work provides a new route to improve the HDI hardening of Fe-Cu alloys.

Effects of Alloying Elements on the Volume Fraction of Ordered α_2 Phase Precipitated in Ti-Al-Sn-Zr Alloys

An ideal method has been established for calculating the precipitation of α2 ordered phase in near-α titanium alloys based on the theory on the critical electron concentration for the precipitation of α2 ordered phase in near-α titanium alloys. With complete precipitation of α2 phase in near-α titanium alloys, the alloys can be considered to be composed of two parts： （1） the α2 ordered phase with the stoichiometric atomic ratio of Ti3X; （2） the disorder solid solution with the critical composition in which the α2 ordered phase is just unable to precipitate. By using this method, the volume fractions of α2 ordered phase precipitated in Ti-Al, Ti-Sn, Ti-Al-Sn-Zr alloys with various AI, Sn and/or Zr contents have been calculated. The influences of AI and Sn on the precipitation of α2 ordered phase are discussed. The calculating results show substantial agreement with the experimental ones.

Effect of precipitation/re-dissolution processes from the supersaturated solution on the intestinal absorption of poorly water-soluble drugs

As one of the possible technologies to improve the oral absorption of poorly water-soluble drugs, supersaturable formulation, which enables to dissolve the drug to the higher concentration than their equilibrium solubility, is now attracting the attention (1)This include salt-formation, soliddispersion, co-crystallization or the use of amorphous form.Since supersaturation is a thermodynamically metastable state,supersaturated solution has a high potential to precipitate. Some pharmaceutical excipients.

Microscopic phase-field simulation of L1_2 and D0_(22) phases during the early precipitation process of Ni-Cr-Al alloys

The influence of temperature on the precipitation mechanism and sequence of L 12 and D022 phases during the early precipitation process of a Ni-15.Sat%Cr-14at%Al alloy was simulated based on the microscopic phase-field model. In the range from 873 to 1373 K, the precipitation mechanism transformed from spinodal decomposition to non-classic nucleation and growth; the incubation period prolonged gradually with increasing temperature. The volume fraction of L12 phases increased and that of D022 phases decreased. D022 phases disappeared at 1373 K, and finally single-phase L12 phases were formed.

Microstructure and phase precipitate behavior of Inconel 740H during aging

The microstructure and phase precipitate behavior and their effects on the room temperature hardness and impact toughness of Inconel 740H aged at 750 ℃ for 10000 h were investigated by SEM, TEM and mechanical analysis. The as-received alloy shows a low hardness value of HB 168 and a highest toughness value of 96 J. After an aging treatment at 800 ℃ for 16 h and cooled in air （standard heat-treated condition）, fine γ′ phase particles precipitate within the grains and small carbide particles are located at the grain boundaries. The hardness increases to HB 304 and the impact toughness decreases to 15 J after standard heat treatment. A maximum hardness value of HB 331 is achieved for the alloy aged at 750 ℃ for 300 h. With increasing the aging time from 300 to 10000 h, a decrease of the hardness and toughness is observed along with an enhanced quantity of M23C6 particles and the coarsening of γ′ phase.

Morphology and crystallography of β precipitate phase in Mg-Gd-Y-Nd-Zr alloy

Morphology and crystal structure of β precipitate phase in Mg-7Gd-5Y-1Nd-0.5Zr (mass fraction, %) alloy were characterized by optical microscopy, scanning electron microscopy and transmission electron microscopy. Compositions were determined for β phase using thin foil energy dispersive spectroscopy. Precipitation at 400 ℃ involves formation of platelet and block-shaped β phase. The orientation relationship is and between β precipitate phase and α-Mg matrix with habit planes parallel to , and a composition of Mg5(Y0.4Gd0.4Nd0.2) is suggested for the β phase in Mg-7Gd-5Y-1Nd-0.5Zr alloy.

Simulation of pre-precipitation in Ni_(75)Al_(14)Mo_(11) alloy by microscopic phase-field model

The early precipitation process of Ni（75）Al（14）Mo（11） alloy was simulated by microscopic phase-field model at different temperatures.The microstructure of the alloy,the precipitation time of Llo structure and occupation probability of the three kinds of atoms were investigated.It is indicated that the non-stoichiometric Ll0（Ⅰ/Ⅱ） phases are found in the precipitation process.With the temperature increasing,the appearance time of Ll0 is brought forward.The Ll0（Ⅱ） structure always precipitates earlier than the Ll0（Ⅰ） structure.Compared with lower temperature,higher temperature brings the formation time of Ll0 phase forward and makes Ll0 phase have a higher order degree.But lower temperature shortens the process time of the Ll0 phase to the Ll2 phase.Al and Mo atoms tend to occupy γ site,Ni atom tends to occupy a and β sites.At the same temperature,Al atom has stronger occupation ability than Mo atom in the same site.Ni,Al and Mo collectively form the composited Ll2 structure.

Atomic-scale investigation of precipitate phases in QE22 Mg alloy

Precipitation-hardenable commercial Mg alloy QE22(Mg-2.5Ag-2.ONd-0.7Zr,wt.%)has excellent mechan-ical properties,but precipitates in this alloy have not been well understood.In this work,precipitate phasesγ",γ,andδformed during the isothermal ageing process at 150,200,250,and 300℃have been characterized using atomic-resolution high-angle annular dark-field scanning transmission electron mi-croscopy and atomic-scale energy-dispersive X-ray spectroscopy.The morphology,crystal structure,and orientation relationship of these precipitate phases have been determined.Domain boundaries usually exist in a singleγparticle,which can be characterized by a separation vector of[1(1)01]_(α).Theδphase forms in situ from its precursorγphase,consequently leading to the formation of three different variants within a single 8 particle.The nucleation of theδphase is strongly related to the domain boundaries of the y phase.The formation of theγphase may be promoted by its precursorγ"phase.The similarities in atomic structures of theγ",γ,andδphases are described and discussed,indicating that transfor-mations between these precipitate phases can be accomplished through the diffusion of added alloying elements.

Phase precipitation behavior and tensile properties of as-cast Ni-based superalloy during heat treatment

The phase precipitation behavior and tensile properties of an as-cast Ni-based alloy,IN617B alloy,after solution heat treatment and long-term aging treatment were investigated.Ti(C,N),M6C and M23C6 are the primary precipitates in as-cast microstructure.After solution heat treatment,most of carbides dissolve into the matrix except a few fine Ti(C,N)within grains.During long-term aging at 700°C,the phase precipitation behaviors of the alloy are characterized as follows:(1)M23C6 carbides at grain boundaries(GBs)transform from film-like shape to cellular shape and gradually coarsen due to the decrease of the surface energy and element aggregation to GBs;(2)M23C6 carbides within grains have a bar-like morphology with a preferential growth direction[110]and have a cube-on-cube coherent orientation relationship with the matrixγ;(3)γ?particles inhibit the coarsening of M23C6 within grains by constraining the diffusion of formation elements.Furthermore,the tensile strength of the alloy obviously increases,but the ductility significantly decreases after the aging for 5000 h.The alloy has a relatively stable microstructure which guarantees the excellent tensile properties during long-term aging.

Equilibrium Phase Constituents and Discontinuous Precipitation Behavior of Al-Zn-Cu Alloy with Symmetrical Composition

Through microstructure observation and X-ray diffraction analysis, the equilibrium phase constituents of Al-Zn alloy that contains 2 at. pct Cu at room temperature have been determined as Al-based solid solution (α), Zn-based solid solution and AI4Cu3Zn phase (T'-phase), which are different from a phase, Zn phase and CuZn4 phase originally believed. It is determined that the products of discontinuous precipitation transformation below 277℃ are not the equilibrium phase constituents, but the metastable phases made up of a phase, Zn phase and CuZn4 phase. The phase constituents after discontinuous precipitation of AIZn-2Cu alloy would transform to the ones in equilibrium status: Al-based solid solution (α) in fcc structure, Zn-based solid solution in hcp structure and AI4Cu3Zn phase (T'-phase) ultimately through plastic deformation at room temperature and re-heating treatment below 277℃.

PRECIPITATION AND GROWTH OF PEROVSKITE PHASE IN TITANIUM BEARING BLAST FURNACE SLAG

The effects of transformation of slag composition and additive agents on the morphology, the precipitation behavior, the crystal growth, and the volume fraction (VF) of perovskite (CaO·¤TiO_2) crystal in the Ti-bearing blast furnace slags were investigated. As the morphology of perovskite is dispersed in molten slags, the crystal growth mechanism of the melting of fine dendrites and the coarsening of large grains exist throughout the solidification of molten slags. With the increase of CaO and Fe_2O_3 content, VF of perovskite obviously increases. However, high basicity leads to the viscosity of slag, which results in the reduction of the average equivalent diameter (AED). The experimental results showed that the presence of the additives CaF_2 and MnO efficiently decreased the viscosity of the slags, and obviously improved the morphology of perovskite and promoted its growth.

Precipitation of α_2 Phase in α+β Solution-Treated and Air-cooled Ti-Al-Sn-Zr-Mo-Si-Nd Alloys

A series of Ti-Al-Sn-Zr-Mo-Si-Nd alloys with various content of Al were solution treated in α+β phase field and air-cooled. The precipitation of a2 phase in cooling was investigated by transmission electron microscopic analysis The precipitation characteristic of α2 phase was discussed. The precipitation of α2 phase would proceed by the nucleation and growth of α2 phase dependent on the diffusion of Al atoms. And a comparison on the difference of precipitation of α2 phase was carried out under the conditions of air-cooling and quenching in water. The investigation showed that the air-cooling and even quenching could supply enough time for the precipitation and growth of α2 phase when Al content reached a certain value even though far away from the stoichiometric composition of Ti3Al.

Electrochemical extraction and the analysis of inter-metallic phases and nitrides in tempered duplex stainless steels

During aging at a temperature ranging from 650 -950 ℃,the ferric matrix in duplex stainless steels undergoes various decomposition processes which could form the precipitates of the Sigma （σ） and Chi （X） phases, as well as nitrides. It is well known that these precipitates lead to a reduction in creep ductility and adversely affect toughness and corrosion properties of steel. This experiment carded out qualitative and quantitative analyses of intermetallic phases and nitrides and established an analytical procedure, including specimen preparation, the choosing of the electrolyte and electrolytic systems,electrolytic isolation,wet chemical separation, and physical and chemical analysis, etc. The residues were collected by ultrasonic cleaning and filtration after galvanostatic electrolysis. Dynamic laser scattering sizer （DLS- sizer） ,scanning electron microscope （SEM） and transmission electron microscope （TEM） were used to examine their structure,modality and size. Qualitative and quantitative analyses were performed by using X-ray diffraction （XRD）, oxygen-nitrogen analyzer and wet chemical analysis. Furthermore, there is a discussion on the effect of isothermal treatment on precipitation that occurs at different temperatures for different periods of time.

Effects of solid solution treatment and cooling on morphology of LPSO phase and precipitation hardening behavior of Mg-Dy-Ni alloy

Effects of solid solution treatment and cooling on the morphology of long period stacking order(LPSO)phase and precipitation hardening behavior of Mg?2Dy?0.5Ni(molar fraction,%)alloy were investigated.Microstructures of the as-cast alloy mainly consisted ofα-Mg phase,bamboo-like Mg12DyNi phase with LPSO structure distributed between dendrites and small amounts of cubic Dy phases.During solid solution treatment at565oC for12h and subsequent different cooling conditions,dot-shaped,block,fine lamellar and rod-shaped LPSO phases precipitate in Mg matrix,respectively.For continuous cooling conditions(furnace and air cooling),the fine lamellar LPSO phase generally forms in grain interior and its volume fraction increases and block LPSO phase coarsens with increasing cooling time.For discontinuous cooling conditions(air cooling after furnace cooling to415and265°C),the dot-shaped LPSO grows into the rod-shaped phase,which results in an decrease of cooling hardening behavior of alloy.

PHASE DIAGRAMS AND σ- PHASE PRECIPITATION IN SOME STAINLESS STEELS

ＰＨＡＳＥＤＩＡＧＲＡＭＳＡＮＤσ－ＰＨＡＳＥＰＲＥＣＩＰＩＴＡＴＩＯＮＩＮＳＯＭＥＳＴＡＩＮＬＥＳＳＳＴＥＥＬＳ￥Ｐａｎ，Ｙｏｎｇ；Ｑｉｕ，Ｃａｉａｎ（ＸｉａｎｇｔａｎＵｎｉｖｅｒｓｉｔｙ，Ｘｉａｎｇｔａｎ４１１１０５）Ａｂｓｔｒａｃｔ：Ｐｈａｓｅ...