Molten-alkali etching has been widely used to reveal dislocations in 4H silicon carbide(4H-SiC),which has promoted the identification and statistics of dislocation density in 4H-SiC single crystals.However,the etching...Molten-alkali etching has been widely used to reveal dislocations in 4H silicon carbide(4H-SiC),which has promoted the identification and statistics of dislocation density in 4H-SiC single crystals.However,the etching mechanism of 4H-SiC is limited misunderstood.In this letter,we reveal the anisotropic etching mechanism of the Si face and C face of 4H-SiC by combining molten-KOH etching,X-ray photoelectron spectroscopy(XPS)and first-principles investigations.The activation energies for the molten-KOH etching of the C face and Si face of 4H-SiC are calculated to be 25.09 and 35.75 kcal/mol,respectively.The molten-KOH etching rate of the C face is higher than the Si face.Combining XPS analysis and first-principles calculations,we find that the molten-KOH etching of 4H-SiC is proceeded by the cycling of the oxidation of 4H-SiC by the dissolved oxygen and the removal of oxides by molten KOH.The faster etching rate of the C face is caused by the fact that the oxides on the C face are unstable,and easier to be removed with molten alkali,rather than the C face being easier to be oxidized.展开更多
Zinc-ion batteries(ZIBs)are considered to be one of the most promising candidates to replace lithium-ion batteries(LIBs)due to the high theoretical capacity,low cost and intrinsic safety.However,zinc dendrites,hydroge...Zinc-ion batteries(ZIBs)are considered to be one of the most promising candidates to replace lithium-ion batteries(LIBs)due to the high theoretical capacity,low cost and intrinsic safety.However,zinc dendrites,hydrogen evolution reaction,surface passivation and other side reactions will inevitably occur during the charging and discharging process of Zn anode,which will seriously affect the cycle stability of the battery and hinder its practical application.The etching strategy of Zn anode has attracted wide attention because of its simple operation and broad commercial prospects,and the etched Zn anode can effectively improve its electrochemical performance.However,there is no comprehensive review of the etching strategy of Zn anode.This review first summarizes the challenges faced by Zn anode,then puts forward the etching mechanisms and properties of acid,salt and other etchants.Finally,based on the above discussion,the challenges and opportunities of Zn anode etching strategy are proposed.展开更多
We described a method for obtaining fluorine-free Ti_(3)C_(2)Cl_(2)MXene phases by melting copper in CuCl_(2)instead of aluminum in Ti_(3)AlC_(2).XRD results show that when molten salt CuCl_(2)etches Ti_(3)AlC_(2),it ...We described a method for obtaining fluorine-free Ti_(3)C_(2)Cl_(2)MXene phases by melting copper in CuCl_(2)instead of aluminum in Ti_(3)AlC_(2).XRD results show that when molten salt CuCl_(2)etches Ti_(3)AlC_(2),it forms an intermediate product Ti_(3)CuC_(2),and then reacts with Ti_(3)CuC_(2)to obtain Ti_(3)C_(2)Cl_(2).The reaction of Ti_(3)AlC_(2)and CuCl_(2)at a temperature of 800℃for 2 h to obtain Ti_(3)C_(2)Cl_(2)with an optimal lamellar structure is shown in SEM results.The pseudopotential plane-wave(PP-PW)method is used to calculate on the electronic structure.The etching mechanism is investigated by the total energies of each substance.The chemical reaction of Ti_(3)AlC_(2)and CuCl_(2)will first become Ti_(3)CuC_(2)and Cu,and then become Ti_(3)C_(2)Cl_(2)during the Lewis acid etching process,which are consistent with the experimental results.展开更多
Quartz crystals are the most widely used material in resonant sensors,owing to their excellent piezoelectric and mechanical properties.With the development of portable and wearable devices,higher processing efficiency...Quartz crystals are the most widely used material in resonant sensors,owing to their excellent piezoelectric and mechanical properties.With the development of portable and wearable devices,higher processing efficiency and geometrical precision are required.Wet etching has been proven to be the most efficient etching method for large-scale production of quartz devices,and many wet etching approaches have been developed over the years.However,until now,there has been no systematic review of quartz crystal etching in liquid phase environments.Therefore,this article provides a comprehensive review of the development of wet etching processes and the achievements of the latest research in thisfield,covering conventional wet etching,additive etching,laser-induced backside wet etching,electrochemical etching,and electrochemical discharge machining.For each technique,a brief overview of its characteristics is provided,associated problems are described,and possible solutions are discussed.This review should provide an essential reference and guidance for the future development of processing strategies for the manufacture of quartz crystal devices.展开更多
Biomass-H_(2)O gasification is a complex thermochemical reaction,including three processes of volatile removal:homogeneous/heterogeneous reforming,biochar gasification and etching.The rate-determining step is biochar-...Biomass-H_(2)O gasification is a complex thermochemical reaction,including three processes of volatile removal:homogeneous/heterogeneous reforming,biochar gasification and etching.The rate-determining step is biochar-H_(2)O gasification and etching so the DFT is carried out to see the catalytic role of different metal elements(K/Ni)in the zigzag biochar model.The calculation results show that the gasification of biochar-H_(2)O needs to go through four processes:dissociative adsorption of water,hydrogen transfer(hydrogen desorption,hydrogen atom transfer),carbon dissolution and CO desorption.The energy barrier indicated that the most significant step in reducing the activation energy of K is reflected in the hydrogen transfer step,which is reduced from 374.14 kJ/mol to 152.41 kJ/mol;the catalytic effect of Ni is mainly reflected in the carbon dissolution step,which is reduced from 122.34 kJ/mol to 84.8 kJ/mol.The existence of K causes the edge to have a stronger attraction to H and does not destroy theπbonds of biochar molecules.The destruction ofπbonds is mainly due to the role of H free radicals,while the destruction ofπbonds will lead to easier C-C bond rupture.Ni shows a strong attraction to O in OH,which forms strong Ni-O chemical bonds.Ni can also destroy the aromatic structure directly,making the gasification easier to happen.This study explored the catalytic mechanism of K/Ni on the biochar-H_(2)O gasification at the molecular level and looked forward to the potential synergy of K/Ni,laying a foundation for experimental research and catalyst design.展开更多
Since the discovery in 2011,MXenes have become the rising star in the field of two-dimensional materials.Benefiting from the metallic-level conductivity,large and adjustable gallery spacing,low ion diffusion barrier,r...Since the discovery in 2011,MXenes have become the rising star in the field of two-dimensional materials.Benefiting from the metallic-level conductivity,large and adjustable gallery spacing,low ion diffusion barrier,rich surface chemistry,superior mechanical strength,MXenes exhibit great application prospects in energy storage and conversion,sensors,optoelectronics,electromagnetic interference shielding and biomedicine.Nevertheless,two issues seriously deteriorate the further development of MXenes.One is the high experimental risk of common preparation methods such as HF etching,and the other is the difficulty in obtaining MXenes with controllable surface groups.Recently,Lewis acidic etching,as a brand-new preparation strategy for MXenes,has attracted intensive attention due to its high safety and the ability to endow MXenes with uniform terminations.However,a comprehensive review of Lewis acidic etching method has not been reported yet.Herein,we first introduce the Lewis acidic etching from the following four aspects:etching mechanism,terminations regulation,in-situ formed metals and delamination of multi-layered MXenes.Further,the applications of MXenes and MXene-based hybrids obtained by Lewis acidic etching route in energy storage and conversion,sensors and microwave absorption are carefully summarized.Finally,some challenges and opportunities of Lewis acidic etching strategy are also presented.展开更多
Rational reconstruction of oxygen evolution reaction(OER)precatalysts and performance index of OER catalysts are crucial but still challenging for universal water electrolysis.Herein,we develop a double-cation etching...Rational reconstruction of oxygen evolution reaction(OER)precatalysts and performance index of OER catalysts are crucial but still challenging for universal water electrolysis.Herein,we develop a double-cation etching strategy to tailor the electronic structure of NiMoO_(4),where the prepared NiMoO_(4) nanorods etched by H_(2)O_(2) reconstruct their surface with abundant cation deficiencies and lattice distortion.Calculation results reveal that the double cation deficiencies can make the upshift of d-band center for Ni atoms and the active sites with better oxygen adsorption capacity.As a result,the optimized sample(NMO-30M)possesses an overpotential of 260 mV at 10 mA cm−2 and excellent long-term durability of 162 h.Importantly,in situ Raman test reveals the rapid formation of high-oxidation-state transition metal hydroxide species,which can further help to improve the catalytic activity of NiMoO_(4) in OER.This work highlights the influence of surface remodification and shed some light on activating catalysts.展开更多
In the past few decades,inspired by the superhydrophobic surfaces(SHPS)of animals and plants such as lotus leaves,rose petals,legs of water striders,and wings of butterflies,preparing metal materials with metallic SHP...In the past few decades,inspired by the superhydrophobic surfaces(SHPS)of animals and plants such as lotus leaves,rose petals,legs of water striders,and wings of butterflies,preparing metal materials with metallic SHPS(MSHPS)have attracted great research interest,due to the great prospect in practical applications.To obtain SHPS on conventional metal materials,it is necessary to construct rough surface,followed by modification with low surface energy substances.In this paper,the action mechanism and the current research status of MSHPS were reviewed through the following aspects.Firstly,the model of wetting theory was presented,and then the progress in MSHPS preparation through chemical etching method was discussed.Secondly,the applications of MSHPS in self-cleaning,anti-icing,corrosion resistance,drag reduction,oil-water separation,and other aspects were introduced.Finally,the challenges encountered in the present application of MSHPS were summarized,and the future research interests were discussed.展开更多
In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action...In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action of vibration/acoustic flow coupled flow field,which generated by resonance acoustic mixing.The effects of solvent ratio,temperature,acceleration and experiment time on morphology as well as particle size of RDX crystals were studied.Not only were the morphology,particle size distribution and crystal form of RDX crystals determined,but also the thermal decomposition performance and mechanical sensitivity of spherical RDX were examined and discussed.Results indicated that under the process of solvent/non-solvent volume ratio at 1:2,temperature of 40℃,acceleration of 40 g and experiment time of 4 h,α-type RDX crystal with sphericity of 0.92 can be obtained.Furthermore,the median particle size(D_(50))of spherical RDX crystals is 215.8 μm with a unimodal particle size distribution(size span 1.34).For one thing,the thermal decomposition peak temperature of spherical RDX is about 2.5℃ higher than that of raw RDX,and apparent activation energy reaches 444.68 kJ/mol.For another thing,impact sensitivity and friction sensitivity of spherical RDX are 18.18% and 33.33% lower than that of raw RDX,respectively.It demonstrates that safety of spherical RDX under thermal,impact and friction stimuli has been improved.展开更多
2D MXene(Ti_(3)CNT_(x))has been considered as the most promising electrode material for flexible supercapacitors owing to its metallic conductivity,ultra-high capacitance,and excellent flexibility.However,it suffers f...2D MXene(Ti_(3)CNT_(x))has been considered as the most promising electrode material for flexible supercapacitors owing to its metallic conductivity,ultra-high capacitance,and excellent flexibility.However,it suffers from a severe restacking problem during the electrode fabrication process,limiting the ion transport kinetics and the accessibility of ions in the electrodes,especially in the direction normal to the electrode surface.Herein,we report a NH_(3)-induced in situ etching strategy to fabricate 3D-interconnected porous MXene/carbon dots(p-MC)films for high-performance flexible supercapacitor.The pre-intercalated carbon dots(CDs)first prevent the restacking of MXene to expose more inner electrochemical active sites.The partially decomposed CDs generate NH_(3)for in situ etching of MXene nanosheets toward 3D-interconnected p-MC films.Benefiting from the structural merits and the 3D-interconnected ionic transmission channels,p-MC film electrodes achieve excellent gravimetric capacitance(688.9 F g^(-1)at 2 A g^(-1))and superior rate capability.Moreover,the optimized p-MC electrode is assembled into an asymmetric solid-state flexible supercapacitor with high energy density and superior cycling stability,demonstrating the great promise of p-MC electrode for practical applications.展开更多
Indium gallium tin oxide(IGTO)thin films have the potential for high mobility and lowtemperature processing,which makes them suitable for applications such as display backplanes and high-voltage switching devices.Howe...Indium gallium tin oxide(IGTO)thin films have the potential for high mobility and lowtemperature processing,which makes them suitable for applications such as display backplanes and high-voltage switching devices.However,very few studies have investigated the plasmaetching characteristics of IGTO and changes in its properties after etching.In this study,the etching characteristics of IGTO were investigated using Cl_(2)/Ar plasma,and changes in surface properties were analyzed.Results showed that the etch rate increased with an increase in the proportion of Cl_(2),with the highest etch rate observed at 69 nm min^(-1)in pure Cl_(2)plasma with a gas flow rate of 100 sccm.Furthermore,increased radio-frequency power caused a rise in the etch rate,while a process pressure of 15 m Torr was optimal.The primary etching mechanism for IGTO thin films under Cl_(2)plasma was a chemical reaction,and an increased work function indicated the occurrence of defects on the surface.In addition,the etching process reduced the surface roughness of Cl_(2)-containing plasma,whereas the etching process in pure Ar plasma increased surface roughness.This study contributes to a better understanding of the plasmaetching characteristics of IGTO and changes in its properties after etching,providing valuable insights for IGTO-based applications.展开更多
This paper focuses on the analytical and numerical asymptotical stability of neutral reaction-diffusion equations with piecewise continuous arguments.First,for the analytical solutions of the equations,we derive their...This paper focuses on the analytical and numerical asymptotical stability of neutral reaction-diffusion equations with piecewise continuous arguments.First,for the analytical solutions of the equations,we derive their expressions and asymptotical stability criteria.Second,for the semi-discrete and one-parameter fully-discrete finite element methods solving the above equations,we work out the sufficient conditions for assuring that the finite element solutions are asymptotically stable.Finally,with a typical example with numerical experiments,we illustrate the applicability of the obtained theoretical results.展开更多
Gallium nitride(GaN)/porous silicon(PSi)film was prepared using a pulsed laser deposition method and 1064 nm Nd:YAG laser for optoelectronic applications and a series of Psi substrates were fabricated using a photoele...Gallium nitride(GaN)/porous silicon(PSi)film was prepared using a pulsed laser deposition method and 1064 nm Nd:YAG laser for optoelectronic applications and a series of Psi substrates were fabricated using a photoelectrochemical etching method assisted by laser at different etching times for 2.5–15 min at 2.5 min intervals.X-ray diffraction,room-temperature photoluminescence,atomic force microscopy and field emission scanning electron microscopy images,and electrical characteristics in the prepared GaN on the Psi film were investigated.The optimum Psi substrate was obtained under the following conditions:10 min,10 mA/cm^(2),and 24%hydrofluoric acid.The substrate exhibited two highly cubic crystalline structures at(200)and(400)orientations and yellow visible band photoluminescence,and homogeneous pores formed over the entire surface.The pores had steep oval shapes and were accompanied by small dark pores that appeared topographically and morphologically.The GaN/Psi film fabricated through PLD exhibited a high and hexagonal crystallographic texture in the(002)plane.Spectroscopic properties results revealed that the photoluminescence emission of the deposited nano-GaN films was in the ultraviolet band(374 nm)related to GaN material and in the near-infrared band(730 nm)related to the Psi substrate.The topographical and morphological results of the GaN films confirmed that the deposited film contained spherical grains with an average diameter of 51.8 nm and surface roughness of 4.8 nm.The GaN/Psi surface showed a cauliflower-like morphology,and the built-in voltage decreased from 3.4 to 2.7 eV after deposition.The fabricated GaN/Psi film exhibited good electrical characteristics.展开更多
A H_(2)O_(2)etching strategy was adopted to introduce coordinatively unsaturated sites(CUS)on MoS_(2)-based catalysts for dibenzothiophene(DBT)hydrodesulfurization(HDS).The CUS concentrations on MoS_(2) slabs were fin...A H_(2)O_(2)etching strategy was adopted to introduce coordinatively unsaturated sites(CUS)on MoS_(2)-based catalysts for dibenzothiophene(DBT)hydrodesulfurization(HDS).The CUS concentrations on MoS_(2) slabs were finely regulated by changing the concentrations of H_(2)O_(2)solution.With the increasing H_(2)O_(2)concentrations(0.1–0.3 mol/L),The CUS concentrations on MoS_(2) slabs increased gradually.However,the high-concentration H_(2)O_(2)etching(0.5 mol/L)increased the MoOxSy and MoO_(3) contents on MoS_(2) slabs compared to etching with the H_(2)O_(2)concentration of 0.3 mol/L,which led to the less CUS concentration in the sulfided Mo–H-0.5 catalyst than in the sulfided Mo–H-0.3 catalyst.A microstructure-activity correlation indicated that the CUS introduced by H_(2)O_(2)etching on MoS_(2) slabs significantly enhanced DBT HDS.Different Co loadings were further introduced into Mo–H-0.3,which had the most CUS concentration,and the corresponding 0.2-CoMo catalyst with the highest CoMoS content(3.853 wt%)exhibited the highest reaction rate constant of 6.95×10^(−6)mol g^(−1)s^(−1)among these CoMo catalysts.展开更多
In this paper,the dynamical behavior of a reaction-diffusion system with quiescence in a closed environment is investigated.The global existence of the solution is obtained by the upper and lower solution method,and t...In this paper,the dynamical behavior of a reaction-diffusion system with quiescence in a closed environment is investigated.The global existence of the solution is obtained by the upper and lower solution method,and the dissipative structure of the system is derived by constructing Lyapunov functions.展开更多
Direct exposure of samples to the active species of air generated by a One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) has been used to etch and to increase the surface energy of metallic surfaces, photoresist, ...Direct exposure of samples to the active species of air generated by a One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) has been used to etch and to increase the surface energy of metallic surfaces, photoresist, polymer films, and nonwoven fab- rics. The OAUGDP is a non-thermal plasma with the classical characteristics of a DC normal glow discharge that operates in air (and other gases) at atmospheric pres- sure. Neither a vacuum system nor batch processing is necessary. A wide range of applications to metals, photoresist, films, fabrics, and polymeric webs can be accom- modated by direct exposure of the workpiece to the plasma in parallel-plate reactors. This technolopy is simple, it produces effects that can be obtained in no other way at one atmosphere; it generates minimal pollutants or unwanted by-products; and it is suitable for individual sample or online treatment of metallic surfaces, wafers, films, and fabrics. Early exposures of solid materials to the OAUGDP required minutes to produce rela- tively small increases of surface energy. These durations appeared too long for com- mercial application to fast-moving webs. Recent improvements in OAUGDP gas com- position, power density, plasma quality, recireulating gas flow, and impedance match- ing of the power supply to the parallel plate plasma reactor have made it possible to raise the surface energy of a variety of polymeric webs (PP, PET PE etc.) to levels of 60 to 70 dynes/cm with one second of exposure. In air plasmas, the high surface ener- gies are not durable, and fall to 50 dynes/cm after periods of weeks to months. Here, we report the exposure of metallic surfaces, photoresist, polymeric films, and nonwo- ven fabrics made of PP and PET to an impedance matched parallel plate OAUGDP for durations ranging from one second to several tens of seconds. Data will be re- ported on the surface energy, wettability, wickability, and aging effect of polymeric films and fabrics as functions of time of exposure, and time after exposure; the rate and uniformity of photoresist etching; and the production of sub-micron structures by OAUGDP etching at one atmosphere.展开更多
A study of Cl2/BCl3-based inductively coupled plasma (ICP) was conducted using thick photoresist mask for anisotropic etching of 50μm diameter holes in a GaAs wafer at a relatively high average etching rate for etc...A study of Cl2/BCl3-based inductively coupled plasma (ICP) was conducted using thick photoresist mask for anisotropic etching of 50μm diameter holes in a GaAs wafer at a relatively high average etching rate for etching depths of more than 150μm. Plasma etch characteristics with ICP process pressure and the percentage of BCI3 were studied in greater detail at a constant ICP coil/bias power. The measured peak-to-peak voltage as a function of pressure was used to estimate the minimum energy of the ions bombarding the substrate. The process pressure was found to have a substantial influence on the energy of heavy ions. Various ion species in plasma showed minimum energy variation from 1.85 eV to 7.5 eV in the pressure range of 20 mTorr to 50 mTorr. The effect of pressure and the percentage of BCl3 on the etching rate and surface smoothness of the bottom surface of the etched hole were studied for a fixed total flow rate. The etching rate was found to decrease with the percentage of BCl3, whereas the addition of BCl3 resulted in anisotropic holes with a smooth veil free bottom surface at a pressure of 30 mTorr and 42% BC13. In addition, variation of the etching yield with pressure and etching depth were also investigated.展开更多
The morphologies of tunnel tips in different stages for aluminum foils during DC etching in 1.5 mol/L HC1 solution at 90℃ were observed by field emission scanning electron microscopy (FE-SEM). A novel model was pro...The morphologies of tunnel tips in different stages for aluminum foils during DC etching in 1.5 mol/L HC1 solution at 90℃ were observed by field emission scanning electron microscopy (FE-SEM). A novel model was proposed to describe the morphological evolution of tunnel tips throughout the growth processes. In the pit nucleation stage, the pits vary from the hemispherical to half-cubic shapes due to the activation of pit tips from the center to the edge. During the tunnel growth stage, the pits dissolve toward the depth direction and develop into the tunnels, and their tips remain flat. In the tip passivation stage, as the passivation of tunnel tips speeds up from the edge to the center's the tunnel tips change from flat shapes to three-dimensional protrusions. The mechanism may be attributed to the order of activation or passivation on the tunnel tips changed in different stages.展开更多
With high hardness, high thermal and chemical stability and excellent optical performance, hard materials exhibit great potential applications in various fields, especially in harsh conditions. Femtosecond laser ablat...With high hardness, high thermal and chemical stability and excellent optical performance, hard materials exhibit great potential applications in various fields, especially in harsh conditions. Femtosecond laser ablation has the capability to fabricate three-dimensional micro/nanostructures in hard materials. However, the low efficiency, low precision and high surface roughness are the main stumbling blocks for femtosecond laser processing of hard materials. So far, etching- assisted femtosecond laser modification has demonstrated to be the efficient strategy to solve the above problems when processing hard materials, including wet etching and dry etching. In this review, femtosecond laser modification that would influence the etching selectivity is introduced. The fundamental and recent applications of the two kinds of etching assisted femtosecond laser modification technologies are summarized. In addition, the challenges and application prospects of these technologies are discussed.展开更多
基金This work is supported by the Natural Science Foundation of China(Grant Nos.62274143&62204216)Joint Funds of the Zhejiang Provincial Natural Science Foundation of China(Grant Nos.LHZSD24E020001)+4 种基金the“Pioneer”and“Leading Goose”R&D Program of Zhejiang(Grant Nos.2022C0102&2023C01010)Partial support was provided by the Leading Innovative and Entrepreneur Team Introduction Program of Hangzhou(Grant No.TD2022012)Fundamental Research Funds for the Central Universities(Grant No.226-2022-00200)the Natural Science Foundation of China for Innovative Research Groups(Grant No.61721005)the Open Fund of Zhejiang Provincial Key Laboratory of Wide Bandgap Semiconductors,Hangzhou Global Scientific and Technological Innovation Center,Zhejiang University.
文摘Molten-alkali etching has been widely used to reveal dislocations in 4H silicon carbide(4H-SiC),which has promoted the identification and statistics of dislocation density in 4H-SiC single crystals.However,the etching mechanism of 4H-SiC is limited misunderstood.In this letter,we reveal the anisotropic etching mechanism of the Si face and C face of 4H-SiC by combining molten-KOH etching,X-ray photoelectron spectroscopy(XPS)and first-principles investigations.The activation energies for the molten-KOH etching of the C face and Si face of 4H-SiC are calculated to be 25.09 and 35.75 kcal/mol,respectively.The molten-KOH etching rate of the C face is higher than the Si face.Combining XPS analysis and first-principles calculations,we find that the molten-KOH etching of 4H-SiC is proceeded by the cycling of the oxidation of 4H-SiC by the dissolved oxygen and the removal of oxides by molten KOH.The faster etching rate of the C face is caused by the fact that the oxides on the C face are unstable,and easier to be removed with molten alkali,rather than the C face being easier to be oxidized.
基金supported by the Science and Technology Research Project of the Education Department of Jilin Province (JJKH20230803KJ)。
文摘Zinc-ion batteries(ZIBs)are considered to be one of the most promising candidates to replace lithium-ion batteries(LIBs)due to the high theoretical capacity,low cost and intrinsic safety.However,zinc dendrites,hydrogen evolution reaction,surface passivation and other side reactions will inevitably occur during the charging and discharging process of Zn anode,which will seriously affect the cycle stability of the battery and hinder its practical application.The etching strategy of Zn anode has attracted wide attention because of its simple operation and broad commercial prospects,and the etched Zn anode can effectively improve its electrochemical performance.However,there is no comprehensive review of the etching strategy of Zn anode.This review first summarizes the challenges faced by Zn anode,then puts forward the etching mechanisms and properties of acid,salt and other etchants.Finally,based on the above discussion,the challenges and opportunities of Zn anode etching strategy are proposed.
基金Funded by the National Natural Science Foundation for Young Scholars of China(No.51302073)the Hubei Provincial Key Laboratory of Green Materials for Light IndustryHubei University of Technology(No.202307B07)。
文摘We described a method for obtaining fluorine-free Ti_(3)C_(2)Cl_(2)MXene phases by melting copper in CuCl_(2)instead of aluminum in Ti_(3)AlC_(2).XRD results show that when molten salt CuCl_(2)etches Ti_(3)AlC_(2),it forms an intermediate product Ti_(3)CuC_(2),and then reacts with Ti_(3)CuC_(2)to obtain Ti_(3)C_(2)Cl_(2).The reaction of Ti_(3)AlC_(2)and CuCl_(2)at a temperature of 800℃for 2 h to obtain Ti_(3)C_(2)Cl_(2)with an optimal lamellar structure is shown in SEM results.The pseudopotential plane-wave(PP-PW)method is used to calculate on the electronic structure.The etching mechanism is investigated by the total energies of each substance.The chemical reaction of Ti_(3)AlC_(2)and CuCl_(2)will first become Ti_(3)CuC_(2)and Cu,and then become Ti_(3)C_(2)Cl_(2)during the Lewis acid etching process,which are consistent with the experimental results.
基金supported by the Natural Science Foundation of China (Grant No.12234005)the major research and development program of Jiangsu Province (Grant Nos.BE2021007-2 and BK20222007)。
文摘Quartz crystals are the most widely used material in resonant sensors,owing to their excellent piezoelectric and mechanical properties.With the development of portable and wearable devices,higher processing efficiency and geometrical precision are required.Wet etching has been proven to be the most efficient etching method for large-scale production of quartz devices,and many wet etching approaches have been developed over the years.However,until now,there has been no systematic review of quartz crystal etching in liquid phase environments.Therefore,this article provides a comprehensive review of the development of wet etching processes and the achievements of the latest research in thisfield,covering conventional wet etching,additive etching,laser-induced backside wet etching,electrochemical etching,and electrochemical discharge machining.For each technique,a brief overview of its characteristics is provided,associated problems are described,and possible solutions are discussed.This review should provide an essential reference and guidance for the future development of processing strategies for the manufacture of quartz crystal devices.
基金Sponsored by the National Natural Science Foundation of China(Grant No.52276180)the Natural Science Foundation of Heilongjiang Province(Grant No.YQ2022E026).
文摘Biomass-H_(2)O gasification is a complex thermochemical reaction,including three processes of volatile removal:homogeneous/heterogeneous reforming,biochar gasification and etching.The rate-determining step is biochar-H_(2)O gasification and etching so the DFT is carried out to see the catalytic role of different metal elements(K/Ni)in the zigzag biochar model.The calculation results show that the gasification of biochar-H_(2)O needs to go through four processes:dissociative adsorption of water,hydrogen transfer(hydrogen desorption,hydrogen atom transfer),carbon dissolution and CO desorption.The energy barrier indicated that the most significant step in reducing the activation energy of K is reflected in the hydrogen transfer step,which is reduced from 374.14 kJ/mol to 152.41 kJ/mol;the catalytic effect of Ni is mainly reflected in the carbon dissolution step,which is reduced from 122.34 kJ/mol to 84.8 kJ/mol.The existence of K causes the edge to have a stronger attraction to H and does not destroy theπbonds of biochar molecules.The destruction ofπbonds is mainly due to the role of H free radicals,while the destruction ofπbonds will lead to easier C-C bond rupture.Ni shows a strong attraction to O in OH,which forms strong Ni-O chemical bonds.Ni can also destroy the aromatic structure directly,making the gasification easier to happen.This study explored the catalytic mechanism of K/Ni on the biochar-H_(2)O gasification at the molecular level and looked forward to the potential synergy of K/Ni,laying a foundation for experimental research and catalyst design.
基金supported by the Highstar Corporation HSD20210118Taihu Electric Corporation 0001。
文摘Since the discovery in 2011,MXenes have become the rising star in the field of two-dimensional materials.Benefiting from the metallic-level conductivity,large and adjustable gallery spacing,low ion diffusion barrier,rich surface chemistry,superior mechanical strength,MXenes exhibit great application prospects in energy storage and conversion,sensors,optoelectronics,electromagnetic interference shielding and biomedicine.Nevertheless,two issues seriously deteriorate the further development of MXenes.One is the high experimental risk of common preparation methods such as HF etching,and the other is the difficulty in obtaining MXenes with controllable surface groups.Recently,Lewis acidic etching,as a brand-new preparation strategy for MXenes,has attracted intensive attention due to its high safety and the ability to endow MXenes with uniform terminations.However,a comprehensive review of Lewis acidic etching method has not been reported yet.Herein,we first introduce the Lewis acidic etching from the following four aspects:etching mechanism,terminations regulation,in-situ formed metals and delamination of multi-layered MXenes.Further,the applications of MXenes and MXene-based hybrids obtained by Lewis acidic etching route in energy storage and conversion,sensors and microwave absorption are carefully summarized.Finally,some challenges and opportunities of Lewis acidic etching strategy are also presented.
基金supported by the National Natural Science Foundation of China(No.12004146)Natural Science Foundation of Gansu Province,China(Nos.20JR5RA303 and 20JR10RA648)the Fundamental Research Funds for the Central Universities(No.LZUMMM2022007).
文摘Rational reconstruction of oxygen evolution reaction(OER)precatalysts and performance index of OER catalysts are crucial but still challenging for universal water electrolysis.Herein,we develop a double-cation etching strategy to tailor the electronic structure of NiMoO_(4),where the prepared NiMoO_(4) nanorods etched by H_(2)O_(2) reconstruct their surface with abundant cation deficiencies and lattice distortion.Calculation results reveal that the double cation deficiencies can make the upshift of d-band center for Ni atoms and the active sites with better oxygen adsorption capacity.As a result,the optimized sample(NMO-30M)possesses an overpotential of 260 mV at 10 mA cm−2 and excellent long-term durability of 162 h.Importantly,in situ Raman test reveals the rapid formation of high-oxidation-state transition metal hydroxide species,which can further help to improve the catalytic activity of NiMoO_(4) in OER.This work highlights the influence of surface remodification and shed some light on activating catalysts.
基金the financial support of Shanghai Pujiang Program(22PJD001)the Scientific Research Project from Science and Technology Commission of Shanghai Municipality(19DZ1204903)the Fundamental Research Funds for the Central Universities(2232021G-11)。
文摘In the past few decades,inspired by the superhydrophobic surfaces(SHPS)of animals and plants such as lotus leaves,rose petals,legs of water striders,and wings of butterflies,preparing metal materials with metallic SHPS(MSHPS)have attracted great research interest,due to the great prospect in practical applications.To obtain SHPS on conventional metal materials,it is necessary to construct rough surface,followed by modification with low surface energy substances.In this paper,the action mechanism and the current research status of MSHPS were reviewed through the following aspects.Firstly,the model of wetting theory was presented,and then the progress in MSHPS preparation through chemical etching method was discussed.Secondly,the applications of MSHPS in self-cleaning,anti-icing,corrosion resistance,drag reduction,oil-water separation,and other aspects were introduced.Finally,the challenges encountered in the present application of MSHPS were summarized,and the future research interests were discussed.
文摘In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action of vibration/acoustic flow coupled flow field,which generated by resonance acoustic mixing.The effects of solvent ratio,temperature,acceleration and experiment time on morphology as well as particle size of RDX crystals were studied.Not only were the morphology,particle size distribution and crystal form of RDX crystals determined,but also the thermal decomposition performance and mechanical sensitivity of spherical RDX were examined and discussed.Results indicated that under the process of solvent/non-solvent volume ratio at 1:2,temperature of 40℃,acceleration of 40 g and experiment time of 4 h,α-type RDX crystal with sphericity of 0.92 can be obtained.Furthermore,the median particle size(D_(50))of spherical RDX crystals is 215.8 μm with a unimodal particle size distribution(size span 1.34).For one thing,the thermal decomposition peak temperature of spherical RDX is about 2.5℃ higher than that of raw RDX,and apparent activation energy reaches 444.68 kJ/mol.For another thing,impact sensitivity and friction sensitivity of spherical RDX are 18.18% and 33.33% lower than that of raw RDX,respectively.It demonstrates that safety of spherical RDX under thermal,impact and friction stimuli has been improved.
基金The authors gratefully acknowledge financial support from the National Natural Science Foundation of China(Grant Nos.21805261 and 51972277)Sichuan Science and Technology Program(Grant Nos.2021YFG0251 and 2022YFG0293)Fundamental Research Funds for the Central Universities(Grant No.2682021CX105)。
文摘2D MXene(Ti_(3)CNT_(x))has been considered as the most promising electrode material for flexible supercapacitors owing to its metallic conductivity,ultra-high capacitance,and excellent flexibility.However,it suffers from a severe restacking problem during the electrode fabrication process,limiting the ion transport kinetics and the accessibility of ions in the electrodes,especially in the direction normal to the electrode surface.Herein,we report a NH_(3)-induced in situ etching strategy to fabricate 3D-interconnected porous MXene/carbon dots(p-MC)films for high-performance flexible supercapacitor.The pre-intercalated carbon dots(CDs)first prevent the restacking of MXene to expose more inner electrochemical active sites.The partially decomposed CDs generate NH_(3)for in situ etching of MXene nanosheets toward 3D-interconnected p-MC films.Benefiting from the structural merits and the 3D-interconnected ionic transmission channels,p-MC film electrodes achieve excellent gravimetric capacitance(688.9 F g^(-1)at 2 A g^(-1))and superior rate capability.Moreover,the optimized p-MC electrode is assembled into an asymmetric solid-state flexible supercapacitor with high energy density and superior cycling stability,demonstrating the great promise of p-MC electrode for practical applications.
基金supported by the Chung-Ang University Research Grants in 2021the National Research Foundation(NRF)of Korea(No.2020R1G1A1102692)。
文摘Indium gallium tin oxide(IGTO)thin films have the potential for high mobility and lowtemperature processing,which makes them suitable for applications such as display backplanes and high-voltage switching devices.However,very few studies have investigated the plasmaetching characteristics of IGTO and changes in its properties after etching.In this study,the etching characteristics of IGTO were investigated using Cl_(2)/Ar plasma,and changes in surface properties were analyzed.Results showed that the etch rate increased with an increase in the proportion of Cl_(2),with the highest etch rate observed at 69 nm min^(-1)in pure Cl_(2)plasma with a gas flow rate of 100 sccm.Furthermore,increased radio-frequency power caused a rise in the etch rate,while a process pressure of 15 m Torr was optimal.The primary etching mechanism for IGTO thin films under Cl_(2)plasma was a chemical reaction,and an increased work function indicated the occurrence of defects on the surface.In addition,the etching process reduced the surface roughness of Cl_(2)-containing plasma,whereas the etching process in pure Ar plasma increased surface roughness.This study contributes to a better understanding of the plasmaetching characteristics of IGTO and changes in its properties after etching,providing valuable insights for IGTO-based applications.
文摘This paper focuses on the analytical and numerical asymptotical stability of neutral reaction-diffusion equations with piecewise continuous arguments.First,for the analytical solutions of the equations,we derive their expressions and asymptotical stability criteria.Second,for the semi-discrete and one-parameter fully-discrete finite element methods solving the above equations,we work out the sufficient conditions for assuring that the finite element solutions are asymptotically stable.Finally,with a typical example with numerical experiments,we illustrate the applicability of the obtained theoretical results.
文摘Gallium nitride(GaN)/porous silicon(PSi)film was prepared using a pulsed laser deposition method and 1064 nm Nd:YAG laser for optoelectronic applications and a series of Psi substrates were fabricated using a photoelectrochemical etching method assisted by laser at different etching times for 2.5–15 min at 2.5 min intervals.X-ray diffraction,room-temperature photoluminescence,atomic force microscopy and field emission scanning electron microscopy images,and electrical characteristics in the prepared GaN on the Psi film were investigated.The optimum Psi substrate was obtained under the following conditions:10 min,10 mA/cm^(2),and 24%hydrofluoric acid.The substrate exhibited two highly cubic crystalline structures at(200)and(400)orientations and yellow visible band photoluminescence,and homogeneous pores formed over the entire surface.The pores had steep oval shapes and were accompanied by small dark pores that appeared topographically and morphologically.The GaN/Psi film fabricated through PLD exhibited a high and hexagonal crystallographic texture in the(002)plane.Spectroscopic properties results revealed that the photoluminescence emission of the deposited nano-GaN films was in the ultraviolet band(374 nm)related to GaN material and in the near-infrared band(730 nm)related to the Psi substrate.The topographical and morphological results of the GaN films confirmed that the deposited film contained spherical grains with an average diameter of 51.8 nm and surface roughness of 4.8 nm.The GaN/Psi surface showed a cauliflower-like morphology,and the built-in voltage decreased from 3.4 to 2.7 eV after deposition.The fabricated GaN/Psi film exhibited good electrical characteristics.
基金support of the National Natural Science Foundation of China(Grant Nos.21978323 and 22108145).
文摘A H_(2)O_(2)etching strategy was adopted to introduce coordinatively unsaturated sites(CUS)on MoS_(2)-based catalysts for dibenzothiophene(DBT)hydrodesulfurization(HDS).The CUS concentrations on MoS_(2) slabs were finely regulated by changing the concentrations of H_(2)O_(2)solution.With the increasing H_(2)O_(2)concentrations(0.1–0.3 mol/L),The CUS concentrations on MoS_(2) slabs increased gradually.However,the high-concentration H_(2)O_(2)etching(0.5 mol/L)increased the MoOxSy and MoO_(3) contents on MoS_(2) slabs compared to etching with the H_(2)O_(2)concentration of 0.3 mol/L,which led to the less CUS concentration in the sulfided Mo–H-0.5 catalyst than in the sulfided Mo–H-0.3 catalyst.A microstructure-activity correlation indicated that the CUS introduced by H_(2)O_(2)etching on MoS_(2) slabs significantly enhanced DBT HDS.Different Co loadings were further introduced into Mo–H-0.3,which had the most CUS concentration,and the corresponding 0.2-CoMo catalyst with the highest CoMoS content(3.853 wt%)exhibited the highest reaction rate constant of 6.95×10^(−6)mol g^(−1)s^(−1)among these CoMo catalysts.
文摘In this paper,the dynamical behavior of a reaction-diffusion system with quiescence in a closed environment is investigated.The global existence of the solution is obtained by the upper and lower solution method,and the dissipative structure of the system is derived by constructing Lyapunov functions.
文摘Direct exposure of samples to the active species of air generated by a One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) has been used to etch and to increase the surface energy of metallic surfaces, photoresist, polymer films, and nonwoven fab- rics. The OAUGDP is a non-thermal plasma with the classical characteristics of a DC normal glow discharge that operates in air (and other gases) at atmospheric pres- sure. Neither a vacuum system nor batch processing is necessary. A wide range of applications to metals, photoresist, films, fabrics, and polymeric webs can be accom- modated by direct exposure of the workpiece to the plasma in parallel-plate reactors. This technolopy is simple, it produces effects that can be obtained in no other way at one atmosphere; it generates minimal pollutants or unwanted by-products; and it is suitable for individual sample or online treatment of metallic surfaces, wafers, films, and fabrics. Early exposures of solid materials to the OAUGDP required minutes to produce rela- tively small increases of surface energy. These durations appeared too long for com- mercial application to fast-moving webs. Recent improvements in OAUGDP gas com- position, power density, plasma quality, recireulating gas flow, and impedance match- ing of the power supply to the parallel plate plasma reactor have made it possible to raise the surface energy of a variety of polymeric webs (PP, PET PE etc.) to levels of 60 to 70 dynes/cm with one second of exposure. In air plasmas, the high surface ener- gies are not durable, and fall to 50 dynes/cm after periods of weeks to months. Here, we report the exposure of metallic surfaces, photoresist, polymeric films, and nonwo- ven fabrics made of PP and PET to an impedance matched parallel plate OAUGDP for durations ranging from one second to several tens of seconds. Data will be re- ported on the surface energy, wettability, wickability, and aging effect of polymeric films and fabrics as functions of time of exposure, and time after exposure; the rate and uniformity of photoresist etching; and the production of sub-micron structures by OAUGDP etching at one atmosphere.
文摘A study of Cl2/BCl3-based inductively coupled plasma (ICP) was conducted using thick photoresist mask for anisotropic etching of 50μm diameter holes in a GaAs wafer at a relatively high average etching rate for etching depths of more than 150μm. Plasma etch characteristics with ICP process pressure and the percentage of BCI3 were studied in greater detail at a constant ICP coil/bias power. The measured peak-to-peak voltage as a function of pressure was used to estimate the minimum energy of the ions bombarding the substrate. The process pressure was found to have a substantial influence on the energy of heavy ions. Various ion species in plasma showed minimum energy variation from 1.85 eV to 7.5 eV in the pressure range of 20 mTorr to 50 mTorr. The effect of pressure and the percentage of BCl3 on the etching rate and surface smoothness of the bottom surface of the etched hole were studied for a fixed total flow rate. The etching rate was found to decrease with the percentage of BCl3, whereas the addition of BCl3 resulted in anisotropic holes with a smooth veil free bottom surface at a pressure of 30 mTorr and 42% BC13. In addition, variation of the etching yield with pressure and etching depth were also investigated.
基金the financial support by the Guangxi Hezhou Guidong Electronics Technology Co.Ltd.the Research Project of Guangxi Zhuang Autonomous Region(Nos.1346011-7 and 1298019-11)
文摘The morphologies of tunnel tips in different stages for aluminum foils during DC etching in 1.5 mol/L HC1 solution at 90℃ were observed by field emission scanning electron microscopy (FE-SEM). A novel model was proposed to describe the morphological evolution of tunnel tips throughout the growth processes. In the pit nucleation stage, the pits vary from the hemispherical to half-cubic shapes due to the activation of pit tips from the center to the edge. During the tunnel growth stage, the pits dissolve toward the depth direction and develop into the tunnels, and their tips remain flat. In the tip passivation stage, as the passivation of tunnel tips speeds up from the edge to the center's the tunnel tips change from flat shapes to three-dimensional protrusions. The mechanism may be attributed to the order of activation or passivation on the tunnel tips changed in different stages.
基金This work was supported by the National Key Research and Development Program of China and National Natural Science Foundation of China (NSFC) under Grants 2017YFB1104300,61590930,61825502,61805098 and 61960206003.
文摘With high hardness, high thermal and chemical stability and excellent optical performance, hard materials exhibit great potential applications in various fields, especially in harsh conditions. Femtosecond laser ablation has the capability to fabricate three-dimensional micro/nanostructures in hard materials. However, the low efficiency, low precision and high surface roughness are the main stumbling blocks for femtosecond laser processing of hard materials. So far, etching- assisted femtosecond laser modification has demonstrated to be the efficient strategy to solve the above problems when processing hard materials, including wet etching and dry etching. In this review, femtosecond laser modification that would influence the etching selectivity is introduced. The fundamental and recent applications of the two kinds of etching assisted femtosecond laser modification technologies are summarized. In addition, the challenges and application prospects of these technologies are discussed.