Micron-sized fiber diamond probe for quantum precision measurement of microwave magnetic field

We present a quantitative measurement of the horizontal component of the microwave magnetic field of a coplanar waveguide using a quantum diamond probe in fiber format.The measurement results are compared in detail with simulation,showing a good consistence.Further simulation shows fiber diamond probe brings negligible disturbance to the field under measurement compared to bulk diamond.This method will find important applications ranging from electromagnetic compatibility test and failure analysis of high frequency and high complexity integrated circuits.

The Real-Time,High Precision Phase Difference Measurement of Electron Density in HL-2A Tokamak

This paper introduces a real-time high precision measurement of phase difference based on Field Programmable Gate Array（FPGA） technology,which has been successfully applied to laser grating interference measurement and real-time feedback of plasma electron density in HL-2A tokamak.It can track the changes of electron density while setting the starting point of the density curve to zero.In a laboratory test,the measuring accuracy of phase difference is less than 0.1°,the time resolution is 80 ns,and the feedback delay is 180 μs.

Precision measurement and suppression of low-frequency noise in a current source with double-resonance alignment magnetometers

Low-noise high-stability current sources have essential applications such as neutron electric dipole moment measurement and high-stability magnetometers. Previous studies mainly focused on frequency noise above 0.1 Hz while less on the low-frequency noise/drift. We use double resonance alignment magnetometers(DRAMs) to measure and suppress the low-frequency noise of a homemade current source(CS) board. The CS board noise level is suppressed by about 10 times in the range of 0.001-0.1 Hz and is reduced to 100 n A/√Hz at 0.001 Hz. The relative stability of CS board can reach2.2 × 10^(-8). In addition, the DRAM shows a better resolution and accuracy than a commercial 7.5-digit multimeter when measuring our homemade CS board. Further, by combining the DRAM with a double resonance orientation magnetometer,we may realize a low-noise CS in the 0.001-1000 Hz range.

A multi-sensor-based distributed real-time measurement system for glacier deformation

Glacier disasters occur frequently in alpine regions around the world,but the current conventional geological disaster measurement technology cannot be directly used for glacier disaster measurement.Hence,in this study,a distributed multi-sensor measurement system for glacier deformation was established by integrating piezoelectric sensing,coded sensing,attitude sensing technology and wireless communication technology.The traditional Modbus protocol was optimized to solve the problem of data identification confusion of different acquisition nodes.Through indoor wireless transmission,adaptive performance analysis,error measurement experiment and landslide simulation experiment,the performance of the measurement system was analyzed and evaluated.Using unmanned aerial vehicle technology,the reliability and effectiveness of the measurement system were verified on the site of Galongla glacier in southeastern Tibet,China.The results show that the mean absolute percentage errors were only 1.13%and 2.09%for the displacement and temperature,respectively.The distributed glacier deformation real-time measurement system provides a new means for the assessment of the development process of glacier disasters and disaster prevention and mitigation.

Quantum-enhanced optical precision measurement assisted by low-frequency squeezed vacuum states

Stable low-frequency squeezed vacuum states at a wavelength of 1550 nm were generated.By controlling the squeezing angle of the squeezed vacuum states,two types of low-frequency quadrature-phase squeezed vacuum states and quadrature-amplitude squeezed vacuum states were obtained using one setup respectively.A quantum-enhanced fiber Mach–Zehnder interferometer(FMZI)was demonstrated for low-frequency phase measurement using the generated quadrature-phase squeezed vacuum states that were injected.When phase modulation was measured with the quantumenhanced FMZI,there were above 3 dB quantum improvements beyond the shot-noise limit(SNL)from 40 kHz to 200 kHz,and 2.3 dB quantum improvement beyond the SNL at 20 kHz was obtained.The generated quadrature-amplitude squeezed vacuum state was applied to perform low-frequency amplitude modulation measurement for sensitivity beyond the SNL based on optical fiber construction.There were about 2 dB quantum improvements beyond the SNL from 60 kHz to 200 kHz.The current scheme proves that quantum-enhanced fiber-based sensors are feasible and have potential applications in high-precision measurements based on fiber,particularly in the low-frequency range.

Real-Time Iterative Compensation Framework for Precision Mechatronic Motion Control Systems

With regard to precision/ultra-precision motion systems,it is important to achieve excellent tracking performance for various trajectory tracking tasks even under uncertain external disturbances.In this paper,to overcome the limitation of robustness to trajectory variations and external disturbances in offline feedforward compensation strategies such as iterative learning control(ILC),a novel real-time iterative compensation(RIC)control framework is proposed for precision motion systems without changing the inner closed-loop controller.Specifically,the RIC method can be divided into two parts,i.e.,accurate model prediction and real-time iterative compensation.An accurate prediction model considering lumped disturbances is firstly established to predict tracking errors at future sampling times.In light of predicted errors,a feedforward compensation term is developed to modify the following reference trajectory by real-time iterative calculation.Both the prediction and compen-sation processes are finished in a real-time motion control sampling period.The stability and convergence of the entire control system after real-time iterative compensation is analyzed for different conditions.Various simulation results consistently demonstrate that the proposed RIC framework possesses satisfactory dynamic regulation capability,which contributes to high tracking accuracy comparable to ILC or even better and strong robustness.

A real-time measuring technology for studying distortion of hydraulic turbine blade castings during heat treatment process

During heat treatment process, the distortion behavior inevitably appears in hydraulic turbine blade castings. In this research, a technology was developed for real-time measurement of the distortion in hydraulic turbine blade castings at the still air cooling and forced air cooling stages during heat treatment process. The method was used to measure the distortion behavior at the cooling stages in both normalizing and tempering processes. At the normalization, the distortion at the blade comer near outlet side undergoes four stages with alternating bending along positive and negative directions. At the tempering stage, the distortion could be divided into two steps. The temperature difference between the two surfaces of blade casting was employed to analyze the distortion mechanism. The measured results could be applied to guide the production, and the machining allowance could be reduced by controlling the distortion behavior.

MEASURING PRECISION OF INDUCED POLARIZATION METHOD

ＭＥＡＳＵＲＩＮＧＰＲＥＣＩＳＩＯＮＯＦＩＮＤＵＣＥＤＰＯＬＡＲＩＺＡＴＩＯＮＭＥＴＨＯＤ￥Ｈｅ，Ｊｉｓｈａｎ（ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉｖｅｒｓｉｔｙｏｆＴｅｃｈｎｏｌｏｇｙ，Ｃｈａｎｇｓｈａ４１００８３）Ａｂｓｔｒａｃｔ：Ｏｎｔｈｅｐｒｅｍｉ...

A novel wide-range precision instrument for measuring three-dimensional surface topography

We developed a measuring instrument that had wide range, high precision, small measuring touch force. The instrument for three-dimensional (3D) surface topography measurement was composed of a high precision displacement sensor based on the Michelson interference principle, a 3D platform based on vertical scanning, a measuring and control circuit, and an industrial control computer. It was a closed loop control system, which changed the traditional moving stylus scanning style into a moving platform scanning style. When the workpiece was measured, the lever of the displacement sensor returned to the balanced position in every sample interval according to the zero offset of the displacement sensor. The non-linear error caused by the rotation of the lever was, therefore, very small even if the measuring range was wide. The instrument can measure the roughness and the profile size of a curved surface.

Variable Precision Rough Set and a Fuzzy Measure of Knowledge Based on Variable Precision Rough Set

Variable precision rough set (VPRS) is an extension of rough set theory (RST). By setting threshold value β , VPRS looses the strict definition of approximate boundary in RST. Confident threshold value for β is discussed and the method for deriving decision making rules from an information system is given by an example. An approach to fuzzy measures of knowledge is proposed by applying VPRS to fuzzy sets. Some properties of this measure are studied and a pair of lower and upper approximation operato...

STUDY ON THE OPTICAL FLAT PROFILE HIGH PRECISION MEASURING TECHNOLOGY IN THE METHOD OF LASER DATUM

The physical datum method that uses the laser beam as the physical datum is proposed.A high accuracy of the straight movement on the line above 0.01 μm/100 mm is achieved through applying the method of the closed loop feedback control that uses the laser beam as the datum.The measuring accuracy above 0.05 μm is obtained by applying the self making electric eddy displacement sensor to detect the geometric accuracy of the optical flat.It proves that the laser beam datum method can achieve the high accurcy of the straight movement and has the huge advantage.

TIME-SPACE CONCEPT FOR PRECISION MEASUREMENT

The transformation between time and space is discussed. To improve real-time response speed of intelligent measuring system, the concept of exchanging program execution time with more circuitry is presented working in cycle mode. Displacement measuring by magnification is achieved with period measurement by magnification. To change the condition that traditional precision measurement depends on machining precision greatly, the concept of measuring space with time and theory of time-space coordinate transformation are proposed. Guided by the idea of measuring space with time, differential frequency measurement system and time grating displacement sensor are developed based on the proposed novel methods. And high-precision measurement is achieved without high-precision manufacture, which embeds the remarkable characteristics of low cost but high precision to the devices. Experiment and test results conform the validity of the proposed time-space concept.

Real-time reliability evaluation based on damaged measurement degradation data

A method was proposed to evaluate the real-time reliability for a single product based on damaged measurement degradation data.Most researches on degradation analysis often assumed that the measurement process did not have any impact on the product's performance.However,in some cases,the measurement process may exert extra stress on products being measured.To obtain trustful results in such a situation,a new degradation model was derived.Then,by fusing the prior information of product and its own on-line degradation data,the real-time reliability was evaluated on the basis of Bayesian formula.To make the proposed method more practical,a procedure based on expectation maximization (EM) algorithm was presented to estimate the unknown parameters.Finally,the performance of the proposed method was illustrated by a simulation study.The results show that ignoring the influence of the damaged measurement process can lead to biased evaluation results,if the damaged measurement process is involved.

Precision measurement with atom interferometry

Development of atom interferometry and its application in precision measurement are reviewed in this paper. The principle, features and the implementation of atom interferometers are introduced, the recent progress of precision measurement with atom interferometry, including determination of gravitational constant and fine structure constant, measurement of gravity, gravity gradient and rotation, test of weak equivalence principle, proposal of gravitational wave detection, and measurement of quadratic Zeeman shift are reviewed in detail. Determination of gravitational redshift, new definition of kilogram, and measurement of weak force with atom interferometry are also briefly introduced.

An image mosaic technique with non-overlapping regions based on microscopic vision in precision assembly

Microscopic vision has been widely applied in precision assembly.To achieve sufficiently high resolution in measurements for precision assembly when the sizes of the parts involved exceed the field of view of the vision system,an image mosaic technique must be used.In this paper,a method for constructing an image mosaic with non-overlapping areas with enhanced efficiency is proposed.First,an image mosaic model for the part is created using a geometric model of the measurement system installed on a X-Y-Z precision stages with high repeatability,and a path for image acquisition is established.Second,images are captured along the same path for a specified calibration plate,and an entire image is formed based on the given model.The measurement results obtained from the specified calibration plate are utilized to identify mosaic errors and apply compensation for the part requiring measurement.Experimental results show that the maximum error is less than 4μm for a camera with pixel equivalent 2.46μm,thereby demonstrating the accuracy of the proposed method.This image mosaic technique with non-overlapping regions can simplify image acquisition and reduce the workload involved in constructing an image mosaic.

APPROACH OF IMPROVING PRECISION IN ULTRASONIC DOPPLER BLOODSTREAM SPEED MEASUREMENT BY CHAOS-BASED FREQUENCY DETECTING

It is critical for cerebral vascular disease diagnosis through Doppler to detect the maximum and the minimum of the carotid blood flow speed accurately. A kind of Duffing system under an external periodic power with dump is introduced in the letter, numerical analysis is carried out by four-order Runge-Kutta method. An oscillator array is designed according to the frequency of the ultrasonic wave. When the external signals are inputted, computational algorithm is used to scan the array in turn and analyze the result, and the frequency can be determined. Based on the methods above, detecting the carotid blood flow speed accurately is realized. The Signal-to-Noise Ratio (SNR) of-20.23dB is obtained by the result of experiments. In conclusion, the SNR has been improved and the precision of the measured bloodstream speed has been increased, which can be 0.069% to 0.13%.

Micro-failure process and failure mechanism of brittle rock under uniaxial compression using continuous real-time wave velocity measurement

In this study,the micro-failure process and failure mechanism of a typical brittle rock under uniaxial compression are investigated via continuous real-time measurement of wave velocities.The experimental results indicate that the evolutions of wave velocities became progressively anisotropic under uniaxial loading due to the direction-dependent development of micro-damage.A wave velocity model considering the inner anisotropic crack evolution is proposed to accurately describe the variations of wave velocities during uniaxial compression testing.Based on which,the effective elastic parameters are inferred by a transverse isotropic constitutive model,and the evolutions of the crack density are inversed using a self-consistent damage model.It is found that the propagation of axial cracks dominates the failure process of brittle rock under uniaxial loading and oblique shear cracks develop with the appearance of macrocrack.

Real-time forward modeling and inversion of logging-while-drilling electromagnetic measurements in horizontal wells

Based on the pseudo-analytical equation of electromagnetic log for layered formation,an optimal boundary match method is proposed to adaptively truncate the encountered formation structures.An efficient integral method is put forward to significantly accelerate the convergence of Sommerfeld integral.By asymptotically approximating and subtracting the first reflection/transmission waves from the scattered field,the new Sommerfeld integral method has addressed difficulties encountered by the traditional digital filtering method,such as low computational precision and limited operating range,and realized the acceleration of the computation speed of logging-while-drilling electromagnetic measurements(LWD EM).By making use of the priori information from the offset/pilot wells and interactively adjusting the formation model,the optimum initial guesses of the inversion model is determined in order to predict the nearby formation boundaries.The gradient optimization algorithm is developed and an interactive inversion system for the LWD EM data from the horizontal wells is established.The inverted results of field data demonstrated that the real-time interactive inversion method is capable of providing the accurate boundaries of layers around the wellbore from the LWD EM,and it will benefit the wellbore trajectory optimization and reservoir interpretation.

Real-Time Black Carbon Emissions from Light-Duty Passenger Vehicles Using a Portable Emissions Measurement System

Black carbon(BC)is considered the second largest anthropogenic climate forcer,but the radiative effects of BC are highly correlated with its combustion sources.On-road vehicles are an important source of anthropogenic BC.However,there are major uncertainties in the estimates of the BC emissions from on-road light-duty passenger vehicles(LDPVs),and results obtained with the portable emissions measurement system(PEMS)method are particularly lacking.We developed a PEMS platform and evaluated the on-road BC emissions from ten in-use LDPVs.We demonstrated that the BC emission factors(EFs)of gasoline direction injection(GDI)engine vehicles range from 1.10 to 1.56 mg.km^(-1),which are higher than the EFs of port fuel injection(PFI)engine vehicles(0.10–0.17 mg.km^(-1))by a factor of 11.The BC emissions during the cold-start phase contributed 2%–33%to the total emissions.A strong correlation(R^(2)=0.70)was observed between the relative BC EFs and average vehicle speed,indicating that traffic congestion alleviation could effectively mitigate BC emissions.Moreover,BC and particle number(PN)emissions were linearly correlated(R^(2)=0.90),and compared to PFI engine vehicles,the instantaneous PN-to-BC emission rates of GDI engine vehicles were less sensitive to vehicle specific power-to-velocity(VSPV)increase in all speed ranges.

A new high-precision gravity solid tidal model for Precision Gravity Measurement Facility

It is significant for establishing gravity datum to construct precise gravity solid tidal model,A simple method with relatively low performance is to interpolate tidal parameters from the global gravity solid tide models.A competitive approach is to determine local gravity solid tidal model by harmonic analysis using long-time serial gravity observations.In this paper a new high-precision gravity solid tidal model for Precision Gravity Measurement Facility is estimated from two co-site gravimeters in the cave laboratory using modern international standard data processing techniques,whose accuracy is evaluated further by comparing with previous publications.The results show that:(1)the determined gravity solid tidal models from two co-site gravimeters are in good agreement with each other,of which the maximum differences for amplitude factors and phase delays don’t exceed 0.01700%and 2.50990°,respectively.(2)the performance of the obtained gravity solid tidal model is 0.00411 for amplitude factors and 0.24120°for phase delays,which is a little better than that of previous publications using superconducting gravity data from Wuhan station.(3)our results and methods are corrective and effective.(4)our model is tiny different from that provided by Wuhan station,which implies that it is necessary to construct a gravity solid tidal model for Precision Gravity Measurement Facility,rather than just adopting existing models at Wuhan station.Our results are helpful in realizing the goal of Precision Gravity Measurement Facility.