Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to cap...Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to capture the process of interface migration of the alloy liquid,allowing for an analysis of the relationship between the morphological characteristics of the alloy liquid solidification front and the degree of undercooling.Additionally,the microstructure of the alloy was examined using metallographic microscopy,leading to a systematic study of the microscopic morphological characteristics and evolution laws of the refined structure during rapid solidification.The research reveals that the grain refining mechanism of the Ni-Cu-Co ternary alloy is consistent with that of the binary alloy(Ni-Cu).Specifically,under low undercooling conditions,intense dendritic remelting was found to cause grain refinement,while under high undercooling conditions,recrystallization driven by accumulated stress and plastic strain resulting from the interaction between the liquid flow and the primary dendrites caused by rapid solidification was identified as the main factor contributing to grain refinement.Furthermore,the study highlights the significant role of the Co element in influencing the solidification rate and reheat effect of the alloy.The addition of Co was also found to facilitate the formation of non-segregated solidification structure,indicating its importance in the overall solidification process.展开更多
In Mg-Ca alloys the grain refining mechanism,in particular regarding the role of nucleant substrates,remains the object of debates.Although native MgO is being recognised as a nucleating substrate accounting for grain...In Mg-Ca alloys the grain refining mechanism,in particular regarding the role of nucleant substrates,remains the object of debates.Although native MgO is being recognised as a nucleating substrate accounting for grain refinement of Mg alloys,the possible interactions of MgO with alloying elements that may alter the nucleation potency have not been elucidated yet.Herein,we design casting experiments of Mg-xCa alloys varied qualitatively in number density of native MgO,which are then comprehensively studied by advanced electron microscopy.The results show that grain refinement is enhanced as the particle number density of MgO increases.The native MgO particles are modified by interfacial layers due to the co-segregation of Ca and N solute atoms at the MgO/Mg interface.Using aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy,we reveal the nature of these Ca/N interfacial layers at the atomic scale.Irrespective of the crystallographic termination of MgO,Ca and N co-segregate at the MgO/Mg interface and occupy Mg and O sites,respectively,forming an interfacial structure of a few atomic layers.The interfacial structure is slightly expanded,less ordered and defective compared to the MgO matrix due to compositional deviations,whereby the MgO substrate is altered as a poorer template to nucleate Mg solid.Upon solidification in a TP-1 mould,the impotent MgO particles account for the grain refining mechanism,where they are suggested to participate into nucleation and grain initiation processes in an explosive manner.This work not only reveals the atomic engineering of a substrate through interfacial segregation but also demonstrates the effectiveness of a strategy whereby native MgO particles can be harnessed for grain refinement in Mg-Ca alloys.展开更多
In this work,we aim to introduce some modifications to the Anam-Net deep neural network(DNN)model for segmenting optic cup(OC)and optic disc(OD)in retinal fundus images to estimate the cup-to-disc ratio(CDR).The CDR i...In this work,we aim to introduce some modifications to the Anam-Net deep neural network(DNN)model for segmenting optic cup(OC)and optic disc(OD)in retinal fundus images to estimate the cup-to-disc ratio(CDR).The CDR is a reliable measure for the early diagnosis of Glaucoma.In this study,we developed a lightweight DNN model for OC and OD segmentation in retinal fundus images.Our DNN model is based on modifications to Anam-Net,incorporating an anamorphic depth embedding block.To reduce computational complexity,we employ a fixed filter size for all convolution layers in the encoder and decoder stages as the network deepens.This modification significantly reduces the number of trainable parameters,making the model lightweight and suitable for resource-constrained applications.We evaluate the performance of the developed model using two publicly available retinal image databases,namely RIM-ONE and Drishti-GS.The results demonstrate promising OC segmentation performance across most standard evaluation metrics while achieving analogous results for OD segmentation.We used two retinal fundus image databases named RIM-ONE and Drishti-GS that contained 159 images and 101 retinal images,respectively.For OD segmentation using the RIM-ONE we obtain an f1-score(F1),Jaccard coefficient(JC),and overlapping error(OE)of 0.950,0.9219,and 0.0781,respectively.Similarly,for OC segmentation using the same databases,we achieve scores of 0.8481(F1),0.7428(JC),and 0.2572(OE).Based on these experimental results and the significantly lower number of trainable parameters,we conclude that the developed model is highly suitable for the early diagnosis of glaucoma by accurately estimating the CDR.展开更多
Second-generation high-temperature superconducting(HTS)conductors,specifically rare earth-barium-copper-oxide(REBCO)coated conductor(CC)tapes,are promising candidates for high-energy and high-field superconducting app...Second-generation high-temperature superconducting(HTS)conductors,specifically rare earth-barium-copper-oxide(REBCO)coated conductor(CC)tapes,are promising candidates for high-energy and high-field superconducting applications.With respect to epoxy-impregnated REBCO composite magnets that comprise multilayer components,the thermomechanical characteristics of each component differ considerably under extremely low temperatures and strong electromagnetic fields.Traditional numerical models include homogenized orthotropic models,which simplify overall field calculation but miss detailed multi-physics aspects,and full refinement(FR)ones that are thorough but computationally demanding.Herein,we propose an extended multi-scale approach for analyzing the multi-field characteristics of an epoxy-impregnated composite magnet assembled by HTS pancake coils.This approach combines a global homogenization(GH)scheme based on the homogenized electromagnetic T-A model,a method for solving Maxwell's equations for superconducting materials based on the current vector potential T and the magnetic field vector potential A,and a homogenized orthotropic thermoelastic model to assess the electromagnetic and thermoelastic properties at the macroscopic scale.We then identify“dangerous regions”at the macroscopic scale and obtain finer details using a local refinement(LR)scheme to capture the responses of each component material in the HTS composite tapes at the mesoscopic scale.The results of the present GH-LR multi-scale approach agree well with those of the FR scheme and the experimental data in the literature,indicating that the present approach is accurate and efficient.The proposed GH-LR multi-scale approach can serve as a valuable tool for evaluating the risk of failure in large-scale HTS composite magnets.展开更多
BACKGROUND Cerebral infarction is a local or extensive necrosis of brain tissue.Subsequently,the corresponding neurological deficits appear.The incidence of cerebrovascular diseases in China is increasing gradually.Af...BACKGROUND Cerebral infarction is a local or extensive necrosis of brain tissue.Subsequently,the corresponding neurological deficits appear.The incidence of cerebrovascular diseases in China is increasing gradually.After the onset of cerebrovascular disease,the most common sequelae include movement disorders,language disorders,and cognitive dysfunction.AIM To investigate the effect of early refined nursing program on the prognosis of middle-aged and elderly patients with cerebral infarction combined with cognitive dysfunction.METHODS A retrospective study was conducted to divide 60 patients with cerebral infarction and cognitive impairment into an experimental group(n=32)and a control group(n=28).The experimental group received early intensive care every day,and the control group received daily routine care.The scores of the Mini-Mental State Examination(MMSE)and the Trail Making Test(TMT),as well as the latency and amplitude of the event-related potential P300,were used as main indicators to evaluate changes in cognitive function,and changes in BDNF,TGF-β,and GDNF expression were used as secondary indicators.RESULTS Both groups experienced notable enhancements in MMSE scores,with the experi-mental group demonstrating higher scores than the control group(experimental:28.75±2.31;control:25.84±2.87).Moreover,reductions in TMT-A and TMT-B scores were observed in both groups(experimental:TMT-A 52.36±6.18,TMT-B 98.47±10.23;control:TMT-A 61.48±7.92,TMT-B 112.63±12.55),with the experimental group displaying lower scores.P300 Latency decreased(experimental:270.63 ms±14.28 ms;control:285.72 ms±16.45 ms),while amplitude increased(experimental:7.82μV±1.05μV;control:6.35μV±0.98μV)significantly in both groups,with superior outcomes in the experimental cohort.Additionally,the levels of the growth factors BDNF,TGF-β1,and GDNF surged(experimental:BDNF 48.37 ng/mL±5.62 ng/mL,TGF-β152.14 pg/mL±4.28 pg/mL,GDNF 34.76 ng/mL±3.89 ng/mL;control:BDNF 42.58 ng/mL±4.73 ng/mL,TGF-β146.23 pg/mL±3.94 pg/mL,GDNF 30.25 ng/mL±2.98 ng/mL)in both groups,with higher levels in the experimental group.CONCLUSION For middle-aged and elderly patients with cerebral infarction and cognitive dysfunction,early refined nursing can significantly improve their cognitive function and prognosis.展开更多
Roads are crucial public spaces in cities and serve as a window to showcase the city’s characteristics.They serve not only as a means of urban transportation but also as a crucial spatial carrier for urban communicat...Roads are crucial public spaces in cities and serve as a window to showcase the city’s characteristics.They serve not only as a means of urban transportation but also as a crucial spatial carrier for urban communication activities and a significant location for meeting the increasing demands of people for a better quality of life.The current road infrastructure prioritizes the right of way for cars,neglecting the design of sidewalks and green belts within the road’s boundaries,and extension spaces between buildings and boundary lines of roads.There is a pressing need to improve street space in response to the demand for development transformation and the creation of a warmer city.This paper summarizes common problems in current road spaces,draws on the experience of excellent urban road spaces in foreign countries,discusses new ideas for the refined design of road spaces based on the transformation of road planning concepts,and suggests a reference standard for guiding detailed design.Simultaneously,the review of road construction will incorporate the detailed design of road space to enhance the role of planning in guiding and controlling the construction of road works.展开更多
Objective: To investigate the application effect of refined nursing care in the care for elderly patients with reflux esophagitis. Methods: Following the difference in nursing style, 84 cases of elderly patients with ...Objective: To investigate the application effect of refined nursing care in the care for elderly patients with reflux esophagitis. Methods: Following the difference in nursing style, 84 cases of elderly patients with reflux esophagitis admitted to our hospital from May 2022 to May 2023 were randomly grouped into a control group and a research group, with 42 cases each. The control group was given conventional nursing care and the research group was given refined nursing care. The psychological state and treatment adherence of the two groups of patients after the nursing intervention were compared. Results: After the nursing intervention, the self-rating anxiety scale (SAS) and self-rating depression scale (SDS) scores of the research group were lower than those of the control group (P < 0.05). The treatment compliance of the research group was better than the control group (P < 0.05). Conclusion: The implementation of refined nursing care for elderly patients with reflux esophagitis exhibited a significant effect on improving the patient’s psychological state, treatment compliance, and rehabilitation.展开更多
Objective:To evaluate the application value of a refined quality control management model for a sterilization supply center.Methods:A retrospective analysis was conducted on the work situation of the sterilization sup...Objective:To evaluate the application value of a refined quality control management model for a sterilization supply center.Methods:A retrospective analysis was conducted on the work situation of the sterilization supply center from January 2021 to January 2023.The work situation before January 31,2022,was classified as the control group;a routine quality control management model was implemented,and the work situation after January 31,2022,was classified as the observation group.The quality of medical device management and department satisfaction between the two groups were compared.Results:The timely recovery and supply rate,classification and cleaning pass rate,disinfection pass rate,packaging pass rate,sterilization pass rate,and department satisfaction score in the observation group were all higher than those of the control group(P<0.05).Conclusion:Implementing a refined quality control management model in the sterilization supply center can improve the quality management level of medical devices and department satisfaction and is worthy of promotion.展开更多
Additive manufacturing(AM)of Mg alloys has become a promising strategy for producing complex structures,but the corrosion performance of AM Mg components remains unexploited.In this study,wire and arc additive manufac...Additive manufacturing(AM)of Mg alloys has become a promising strategy for producing complex structures,but the corrosion performance of AM Mg components remains unexploited.In this study,wire and arc additive manufacturing(WAAM)was employed to produce single AZ31 layer.The results revealed that the WAAM AZ31 was characterized by significant grain refinement with non-textured crystallographic orientation,similar phase composition and stabilized corrosion performance comparing to the cast AZ31.These varied corrosion behaviors were principally ascribed to the size of grain,where cast AZ31 and WAAM AZ31 were featured by micro galvanic corrosion and intergranular corrosion,respectively.展开更多
To investigate the effect of rare earth on size and distribution of TiB2 phase in aluminum alloy refiner,Al-5Ti-1B-RE master alloy was fabricated,and its microstructure and phase constitutions were investigated by the...To investigate the effect of rare earth on size and distribution of TiB2 phase in aluminum alloy refiner,Al-5Ti-1B-RE master alloy was fabricated,and its microstructure and phase constitutions were investigated by the combination of first principles calculations and experimental investigation.The calculated results reveal that Ce has the most effective modification ability due to the most positive adsorption energy and the largest charge transfer value compared with other rare earth elements.Results of experimental investigation indicate that the addition of rare earth in the Al-5Ti-1B alloys can greatly refine the particle size of TiB2,improve the distribution of particles and lead to better refinement effect than that of the Al-5Ti-1B alloys without rare earth.Moreover,Ce has the best optimization effect,which agrees well with the calculated results.展开更多
The large dual-channel wide-bodied aircraft has a long range and a high cruise Mach number.Therefore,its aerodynamic design requires a high level ofwind tunnel test refinement.Based on the requirements of aerodynamic ...The large dual-channel wide-bodied aircraft has a long range and a high cruise Mach number.Therefore,its aerodynamic design requires a high level ofwind tunnel test refinement.Based on the requirements of aerodynamic design for the future wide-bodied aircraft and the characteristics of high-speed wind tunnel tests,the error theory is introduced to analyze the factors affecting the accuracy of the test data.This study carries out a series of research on the improvement of refined aerodynamic test technology in an FL-26 wind tunnel,including design and optimization of the support system of wide-bodied aircraft,model attitude angle measurement,Mach number control accuracy,measurement and control system stability,test data correction and perfection,high-precision force balance and standard model development.In addition,the effect of the standard specification of the refined aerodynamic test is investigated to improve the data quality.The research findings have been applied in the standard model test and subsequent models of wide-bodied aircraft.The results show that whenMach numbers are less than 0.9,the control accuracy of Mach numbers in the FL-26 wind tunnel is smaller than 0.001 and the measurement error of attack angle is smaller than 0.01°.Therefore,it has the ability to correct the data influenced by factors,such as support/wall interference,model deformation,floating resistance and airflow deflection angle.The repeatability accuracy of the standard model’s comparison test shows that the lift coefficient is less than or equal to 0.0012,the drag coefficient is less than or equal to 0.00004,pitching moment coefficient is less than or equal to 0.0004.The bending resolution of the model’s deformation measurement is less than 0.2 mm,and the tensional deformation is smaller than 0.04°.The revised aerodynamic data and model deformation measurement results have good agreement with that of the ETW wind tunnel.The results demonstrate that the improved technology presented in this paper can significantly enhance the refined aerodynamic test of wide-bodied aircraft.展开更多
Both Cu60Ni38Co2 and Cu60Ni40 alloy were naturally cooled after rapid solidification from the liquid phase.The transformation law of the microstructure characteristics of the rapidly solidified alloy with the change o...Both Cu60Ni38Co2 and Cu60Ni40 alloy were naturally cooled after rapid solidification from the liquid phase.The transformation law of the microstructure characteristics of the rapidly solidified alloy with the change of undercooling(DT)was systematically studied.It was found that the two alloys experienced the same transformation process.The refinement structures under different undercoolings were characterized by electron backscatter diffraction(EBSD).The experimental results show that the characteristics of the refinement structure of the two alloys with low undercooling are the same,whereas,the characteristics of the refinement structure with high undercooling are opposite.The transmission electron microscope(TEM)results of Cu60Ni38Co2 alloy show that the dislocation network density of low undercooled microstructure is lower than that of high undercooled microstructure.By combining EBSD and TEM,it can be confirmed that the dendrite remelting fracture is the reason for the refinement of the low undercooled structure,while the high undercooled structure is refined due to recrystallization.展开更多
The effects of different complex shear stress conditions on grain refinement and texture evolution of Mg-13Gd-4Y-2Zn-0.5Zr alloy were investigated.With increasing strain rate,the average grain size of compression-shea...The effects of different complex shear stress conditions on grain refinement and texture evolution of Mg-13Gd-4Y-2Zn-0.5Zr alloy were investigated.With increasing strain rate,the average grain size of compression-shear(CS)and compression-torsion(CT)samples are decreased,and the grain size of dynamic recrystallization(DRX)grains is also decreased.This is because that the precipitation number ofβphases is increased,and the hindering effect on grain growth can be significantly enhanced.The DRX fractions of CS and CT samples are decreased with increased strain rate.The low DRX fraction at high strain rate is related to the insufficient time for grains to nucleate.The DRX process can be promoted by the PSN mechanism of second phases,and the grain growth can be restricted by the pinning effect.At the same time,the texture strength is enhanced as the strain rate increased.Besides,the kinking degree of lamellar long-period stacking ordered(LPSO)phases is increased.Under complex shear stress conditions,non-basal slip,especially pyramidal slip,is easily activated and the texture is deflected greatly.Compared with the CS samples,CT samples have smaller average grain size,higher DRX fraction,and lower texture strength for a certain strain rate.This is because that the equivalent stress of the CT sample is larger,the stress triaxiality is smaller,so more serious dislocations are piled up near grain boundaries and second phases.At the same time,since CT sample was sheared with torsion,the dislocation movement path can be called“rotational dislocation accumulation”,and the longer distribution path of the CT sample is generated,so more sub-grains and low-angle grain boundaries(LAGBs)are formed.Compared with the CS sample,more huge-angle grain boundaries(HAGBs)and DRX grains are formed from grain boundary to grain interior,so better grain refinement effect is achieved.展开更多
Erratum to:International Journal of Minerals, Metallurgy and MaterialsVolume 28, Number 7, July 2021, Page 1112 The original version of this article unfortunately contained mistakes. Symbols in Table 2 are used incorr...Erratum to:International Journal of Minerals, Metallurgy and MaterialsVolume 28, Number 7, July 2021, Page 1112 The original version of this article unfortunately contained mistakes. Symbols in Table 2 are used incorrectly.展开更多
Low absolute strength becomes one major obstacle for the wider applications of low/no rare-earth(RE) containing Mg alloys. This review firstly demonstrates the importance of grain refinement in improving strength of M...Low absolute strength becomes one major obstacle for the wider applications of low/no rare-earth(RE) containing Mg alloys. This review firstly demonstrates the importance of grain refinement in improving strength of Mg alloys by comprehensively comparing with other strategy, e.g., precipitation strengthening. Dynamic recrystallization(DRX) plays a crucial role in refining grain size of Mg wrought alloys.Therefore, secondly, the DRX models, grain nucleation mechanisms and the related grain refinement abilities in Mg alloys are summarized,including phase boundary, twin boundary and general boundary induced recrystallization. Thirdly, the newly developed low-RE containing Mg alloy, e.g., Mg-Ce, Mg-Nd and Mg-Sm based alloys, and the RE-free Mg alloys, e.g., Mg-Al, Mg-Zn, Mg-Sn and Mg-Ca based alloy,are reviewed, with the focus on enhancing the mechanical properties mainly via the grain refinement strategy. At the last section, the perspectives and outstanding issues concerning high-performance Mg wrought alloys are also proposed. This review is meant to promote the deep understanding on the critical role of grain refinement in Mg alloys and provide reference for the development of other high strength and low-cost Mg alloys which are fabricated by the conventional extrusion/rolling processing.展开更多
The molten Cu60Ni35Co5 ternary alloy was undercooled by fluxing method and solidified by natural cooling method.The microstructure of all undercooled samples were analyzed.It is found that the rapidly solidified Cu60N...The molten Cu60Ni35Co5 ternary alloy was undercooled by fluxing method and solidified by natural cooling method.The microstructure of all undercooled samples were analyzed.It is found that the rapidly solidified Cu60Ni35Co5 alloy has undergone two grain refinement phenomena within the undercooling range,and its microstructure and morphology change with the undercooling through the transformation process of“coarse dendrite-equiaxed dendrite-oriented fine dendrite-equiaxed crystal”.The refined structure with the maximum undercooling?T of 253 K was selected for electron backscatter diffraction(EBSD)and transmission electron microscopy(TEM)tests.EBSD results show that the refined structure contains a high proportion of large angle grain boundaries(LAGBs),a large number of randomly oriented grains,and high proportion of twins,while TEM results show that the dislocation density in most areas is relatively low.The above characteristics confirm that the solidification structure is refined due to recrystallization behavior under high undercooling.展开更多
High-performance cast magnesium rare-earth(Mg-RE) alloys are one of the most important materials among all developed Mg alloy families, and have shown great potential in military and weapons, aerospace and aviation, o...High-performance cast magnesium rare-earth(Mg-RE) alloys are one of the most important materials among all developed Mg alloy families, and have shown great potential in military and weapons, aerospace and aviation, orthopedic implants, etc. Controlling grain size and distribution of it is key to the promising mechanical performance of Mg-RE alloy casting components. During the casting of a real component, nearly every procedure in the fabrication process will influence the grain refinement effect. The procedure may include and may not be limited to the chemical inoculations, possibly applied physical fields, the interfere between grain refiner and purifications, and the casting techniques with different processing parameters. This paper reviews the recent advances and proposed future developments in these categories on grain refinement of cast Mg-RE alloys. The review will provide insights for the future design of grain refinement techniques,the choosing of processing parameters, and coping strategies for the failure of coarsening for cast Mg-RE components with high quality and good performance.展开更多
Both Cu60Ni38Co2 and Cu60Ni40 alloy were naturally cooled after rapid solidification from the liquid phase.The transformation law of the microstructure characteristics of the rapidly solidified alloy with the change o...Both Cu60Ni38Co2 and Cu60Ni40 alloy were naturally cooled after rapid solidification from the liquid phase.The transformation law of the microstructure characteristics of the rapidly solidified alloy with the change of undercooling(ΔT)was systematically studied.It is found that the two alloys experience the same transformation process.The refinement structures under different undercoolings were characterized by electron backscatter diffraction(EBSD).The results show that the characteristics of the refinement structure of the two alloys with low undercooling are the same,but the characteristics of the refinement structure with high undercooling are opposite.The transmission electron microscopy(TEM)results of Cu60Ni38Co2 alloy show that the dislocation network density of low undercooled microstructure is lower than that of high undercooled microstructure.By combining EBSD and TEM,it could be confirmed that the dendrite remelting fracture is the reason for the refinement of the low undercooled structure,while the high undercooled structure is refined due to recrystallization.On this basis,in the processing of copper base alloys,there will be serious work hardening phenomenon and machining hard problem of consciousness problems caused by excessive cutting force.A twodimensional orthogonal turning finite element model was established using ABAQUS software to analyze the changes in cutting speed and tool trajectory in copper based alloy ultrasonic elliptical vibration turning.The results show that in copper based alloy ultrasonic elliptical vibration turning,cutting process parameters have a significant impact on cutting force.Choosing reasonable process parameters can effectively reduce cutting force and improve machining quality.展开更多
The Al-5Cu alloys were prepared by different treatment methods,including adding a refiner Al-5Ti-1B,exerting a rotating magnetic field(RMF),and compound treatment of both refiner and RMF.The effects of treatment metho...The Al-5Cu alloys were prepared by different treatment methods,including adding a refiner Al-5Ti-1B,exerting a rotating magnetic field(RMF),and compound treatment of both refiner and RMF.The effects of treatment methods on the microstructure,properties,and solid solubility of the Al-5Cu alloy were investigated.The optimal magnetic field parameters and addition amount of refiner were confirmed by experiment.Results show that either RMF or adding refiner Al-5Ti-1B alone can refine the grain size,and the refining effect can be further improved by a compound refining treatment with optimized magnetic field parameters(120 A current and 8 Hz frequency) and 1.0wt.% Al-5Ti-1B refiner(RMF*+Al-5Ti-1B*).The average grain size is decreased to 68.1 μm,which is 60.8%,21.1%,and 83.5% lower than that of the alloy treated by the optimized rotating magnetic field,the Al-5Ti-1B refiner,and the alloy without any treatment,respectively.The tensile strength and elongation of the alloy reach 232.5 MPa and 18.6%,respectively,which are obviously higher than those of the alloys treated by rotating magnetic field,Al-5Ti-1B refiner,and the alloy without any treatment,respectively.Additionally,the solid solubility of the alloy is also obviously improved compared to the alloys treated by other methods.展开更多
Overtopping is one of the main reasons for the breaching of concrete-face sand-gravel dams(CFSGDs).In this study,a refined mathematical model was established based on the characteristics of the overtopping breaching o...Overtopping is one of the main reasons for the breaching of concrete-face sand-gravel dams(CFSGDs).In this study,a refined mathematical model was established based on the characteristics of the overtopping breaching of CFSGDs.The model characteristics were as follows:(1)Based on the Renormailzation Group(RNG)k-εturbulence theory and volume of fluid(VOF)method,the turbulent characteristics of the dam-break flow were simulated,and the erosion surface of the water and soil was tracked;(2)In consideration of the influence of the change in the sediment content on the dam-break flow,the dam material transport equation,which could reflect the characteristics of particle settlement and entrainment motion,was used to simulate the erosion process of the sand gravels;(3)Based on the bending moment balance method,a failure equation of the concrete face slab under dead weight and water load was established.The proposed model was verified through a case study on the failure of the Gouhou CFSGD.The results showed that the proposed model could well simulate the erosion mode of the special vortex flow of the CFSGD scouring the support body of the concrete face slab inward and reflect the mutual coupling relationship between the dam-break flow,sand gravels,and concrete face slabs.Compared with the measured values,the relative errors of the peak discharge,final breach average width,dam breaching duration,and maximum failure length of the face slab calculated using the proposed model were all less than 12%,thus verifying the rationality of the model.The proposed model was demonstrated to perform better and provide more detailed results than three selected parametric models and three simplified mathematical models.The study results can aid in establishing the risk level and devising early warning strategies for CFSGDs.展开更多
基金Funded by the Basic Research Project in Shanxi Province(No.202103021224183)。
文摘Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to capture the process of interface migration of the alloy liquid,allowing for an analysis of the relationship between the morphological characteristics of the alloy liquid solidification front and the degree of undercooling.Additionally,the microstructure of the alloy was examined using metallographic microscopy,leading to a systematic study of the microscopic morphological characteristics and evolution laws of the refined structure during rapid solidification.The research reveals that the grain refining mechanism of the Ni-Cu-Co ternary alloy is consistent with that of the binary alloy(Ni-Cu).Specifically,under low undercooling conditions,intense dendritic remelting was found to cause grain refinement,while under high undercooling conditions,recrystallization driven by accumulated stress and plastic strain resulting from the interaction between the liquid flow and the primary dendrites caused by rapid solidification was identified as the main factor contributing to grain refinement.Furthermore,the study highlights the significant role of the Co element in influencing the solidification rate and reheat effect of the alloy.The addition of Co was also found to facilitate the formation of non-segregated solidification structure,indicating its importance in the overall solidification process.
基金financial support under grant number EP/N007638/1supported by EPSRC under grant number EP/W021080/1
文摘In Mg-Ca alloys the grain refining mechanism,in particular regarding the role of nucleant substrates,remains the object of debates.Although native MgO is being recognised as a nucleating substrate accounting for grain refinement of Mg alloys,the possible interactions of MgO with alloying elements that may alter the nucleation potency have not been elucidated yet.Herein,we design casting experiments of Mg-xCa alloys varied qualitatively in number density of native MgO,which are then comprehensively studied by advanced electron microscopy.The results show that grain refinement is enhanced as the particle number density of MgO increases.The native MgO particles are modified by interfacial layers due to the co-segregation of Ca and N solute atoms at the MgO/Mg interface.Using aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy,we reveal the nature of these Ca/N interfacial layers at the atomic scale.Irrespective of the crystallographic termination of MgO,Ca and N co-segregate at the MgO/Mg interface and occupy Mg and O sites,respectively,forming an interfacial structure of a few atomic layers.The interfacial structure is slightly expanded,less ordered and defective compared to the MgO matrix due to compositional deviations,whereby the MgO substrate is altered as a poorer template to nucleate Mg solid.Upon solidification in a TP-1 mould,the impotent MgO particles account for the grain refining mechanism,where they are suggested to participate into nucleation and grain initiation processes in an explosive manner.This work not only reveals the atomic engineering of a substrate through interfacial segregation but also demonstrates the effectiveness of a strategy whereby native MgO particles can be harnessed for grain refinement in Mg-Ca alloys.
基金funded byResearchers Supporting Project Number(RSPD2024R 553),King Saud University,Riyadh,Saudi Arabia.
文摘In this work,we aim to introduce some modifications to the Anam-Net deep neural network(DNN)model for segmenting optic cup(OC)and optic disc(OD)in retinal fundus images to estimate the cup-to-disc ratio(CDR).The CDR is a reliable measure for the early diagnosis of Glaucoma.In this study,we developed a lightweight DNN model for OC and OD segmentation in retinal fundus images.Our DNN model is based on modifications to Anam-Net,incorporating an anamorphic depth embedding block.To reduce computational complexity,we employ a fixed filter size for all convolution layers in the encoder and decoder stages as the network deepens.This modification significantly reduces the number of trainable parameters,making the model lightweight and suitable for resource-constrained applications.We evaluate the performance of the developed model using two publicly available retinal image databases,namely RIM-ONE and Drishti-GS.The results demonstrate promising OC segmentation performance across most standard evaluation metrics while achieving analogous results for OD segmentation.We used two retinal fundus image databases named RIM-ONE and Drishti-GS that contained 159 images and 101 retinal images,respectively.For OD segmentation using the RIM-ONE we obtain an f1-score(F1),Jaccard coefficient(JC),and overlapping error(OE)of 0.950,0.9219,and 0.0781,respectively.Similarly,for OC segmentation using the same databases,we achieve scores of 0.8481(F1),0.7428(JC),and 0.2572(OE).Based on these experimental results and the significantly lower number of trainable parameters,we conclude that the developed model is highly suitable for the early diagnosis of glaucoma by accurately estimating the CDR.
基金Project supported by the National Natural Science Foundation of China(Nos.11932008 and 12272156)the Fundamental Research Funds for the Central Universities(No.lzujbky-2022-kb06)+1 种基金the Gansu Science and Technology ProgramLanzhou City’s Scientific Research Funding Subsidy to Lanzhou University of China。
文摘Second-generation high-temperature superconducting(HTS)conductors,specifically rare earth-barium-copper-oxide(REBCO)coated conductor(CC)tapes,are promising candidates for high-energy and high-field superconducting applications.With respect to epoxy-impregnated REBCO composite magnets that comprise multilayer components,the thermomechanical characteristics of each component differ considerably under extremely low temperatures and strong electromagnetic fields.Traditional numerical models include homogenized orthotropic models,which simplify overall field calculation but miss detailed multi-physics aspects,and full refinement(FR)ones that are thorough but computationally demanding.Herein,we propose an extended multi-scale approach for analyzing the multi-field characteristics of an epoxy-impregnated composite magnet assembled by HTS pancake coils.This approach combines a global homogenization(GH)scheme based on the homogenized electromagnetic T-A model,a method for solving Maxwell's equations for superconducting materials based on the current vector potential T and the magnetic field vector potential A,and a homogenized orthotropic thermoelastic model to assess the electromagnetic and thermoelastic properties at the macroscopic scale.We then identify“dangerous regions”at the macroscopic scale and obtain finer details using a local refinement(LR)scheme to capture the responses of each component material in the HTS composite tapes at the mesoscopic scale.The results of the present GH-LR multi-scale approach agree well with those of the FR scheme and the experimental data in the literature,indicating that the present approach is accurate and efficient.The proposed GH-LR multi-scale approach can serve as a valuable tool for evaluating the risk of failure in large-scale HTS composite magnets.
文摘BACKGROUND Cerebral infarction is a local or extensive necrosis of brain tissue.Subsequently,the corresponding neurological deficits appear.The incidence of cerebrovascular diseases in China is increasing gradually.After the onset of cerebrovascular disease,the most common sequelae include movement disorders,language disorders,and cognitive dysfunction.AIM To investigate the effect of early refined nursing program on the prognosis of middle-aged and elderly patients with cerebral infarction combined with cognitive dysfunction.METHODS A retrospective study was conducted to divide 60 patients with cerebral infarction and cognitive impairment into an experimental group(n=32)and a control group(n=28).The experimental group received early intensive care every day,and the control group received daily routine care.The scores of the Mini-Mental State Examination(MMSE)and the Trail Making Test(TMT),as well as the latency and amplitude of the event-related potential P300,were used as main indicators to evaluate changes in cognitive function,and changes in BDNF,TGF-β,and GDNF expression were used as secondary indicators.RESULTS Both groups experienced notable enhancements in MMSE scores,with the experi-mental group demonstrating higher scores than the control group(experimental:28.75±2.31;control:25.84±2.87).Moreover,reductions in TMT-A and TMT-B scores were observed in both groups(experimental:TMT-A 52.36±6.18,TMT-B 98.47±10.23;control:TMT-A 61.48±7.92,TMT-B 112.63±12.55),with the experimental group displaying lower scores.P300 Latency decreased(experimental:270.63 ms±14.28 ms;control:285.72 ms±16.45 ms),while amplitude increased(experimental:7.82μV±1.05μV;control:6.35μV±0.98μV)significantly in both groups,with superior outcomes in the experimental cohort.Additionally,the levels of the growth factors BDNF,TGF-β1,and GDNF surged(experimental:BDNF 48.37 ng/mL±5.62 ng/mL,TGF-β152.14 pg/mL±4.28 pg/mL,GDNF 34.76 ng/mL±3.89 ng/mL;control:BDNF 42.58 ng/mL±4.73 ng/mL,TGF-β146.23 pg/mL±3.94 pg/mL,GDNF 30.25 ng/mL±2.98 ng/mL)in both groups,with higher levels in the experimental group.CONCLUSION For middle-aged and elderly patients with cerebral infarction and cognitive dysfunction,early refined nursing can significantly improve their cognitive function and prognosis.
文摘Roads are crucial public spaces in cities and serve as a window to showcase the city’s characteristics.They serve not only as a means of urban transportation but also as a crucial spatial carrier for urban communication activities and a significant location for meeting the increasing demands of people for a better quality of life.The current road infrastructure prioritizes the right of way for cars,neglecting the design of sidewalks and green belts within the road’s boundaries,and extension spaces between buildings and boundary lines of roads.There is a pressing need to improve street space in response to the demand for development transformation and the creation of a warmer city.This paper summarizes common problems in current road spaces,draws on the experience of excellent urban road spaces in foreign countries,discusses new ideas for the refined design of road spaces based on the transformation of road planning concepts,and suggests a reference standard for guiding detailed design.Simultaneously,the review of road construction will incorporate the detailed design of road space to enhance the role of planning in guiding and controlling the construction of road works.
文摘Objective: To investigate the application effect of refined nursing care in the care for elderly patients with reflux esophagitis. Methods: Following the difference in nursing style, 84 cases of elderly patients with reflux esophagitis admitted to our hospital from May 2022 to May 2023 were randomly grouped into a control group and a research group, with 42 cases each. The control group was given conventional nursing care and the research group was given refined nursing care. The psychological state and treatment adherence of the two groups of patients after the nursing intervention were compared. Results: After the nursing intervention, the self-rating anxiety scale (SAS) and self-rating depression scale (SDS) scores of the research group were lower than those of the control group (P < 0.05). The treatment compliance of the research group was better than the control group (P < 0.05). Conclusion: The implementation of refined nursing care for elderly patients with reflux esophagitis exhibited a significant effect on improving the patient’s psychological state, treatment compliance, and rehabilitation.
文摘Objective:To evaluate the application value of a refined quality control management model for a sterilization supply center.Methods:A retrospective analysis was conducted on the work situation of the sterilization supply center from January 2021 to January 2023.The work situation before January 31,2022,was classified as the control group;a routine quality control management model was implemented,and the work situation after January 31,2022,was classified as the observation group.The quality of medical device management and department satisfaction between the two groups were compared.Results:The timely recovery and supply rate,classification and cleaning pass rate,disinfection pass rate,packaging pass rate,sterilization pass rate,and department satisfaction score in the observation group were all higher than those of the control group(P<0.05).Conclusion:Implementing a refined quality control management model in the sterilization supply center can improve the quality management level of medical devices and department satisfaction and is worthy of promotion.
基金the financial support by National Key Research and Development Project(Grand No.2020YFC1107202)Guangdong Basic and Applied Basic Research Foundation(Grand No.2020A1515110754)+3 种基金MOE Key Lab of Disaster Forest and Control in Engineering,Jinan University(Grand No.20200904008)Educational Commission of Guangdong Province(Grand No.2020KTSCX012)the Fundamental Research Funds for Central Universities(Grand No.21620342)the support from National Natural Science Foundation of China,NSFC(Grand No.51775556)。
文摘Additive manufacturing(AM)of Mg alloys has become a promising strategy for producing complex structures,but the corrosion performance of AM Mg components remains unexploited.In this study,wire and arc additive manufacturing(WAAM)was employed to produce single AZ31 layer.The results revealed that the WAAM AZ31 was characterized by significant grain refinement with non-textured crystallographic orientation,similar phase composition and stabilized corrosion performance comparing to the cast AZ31.These varied corrosion behaviors were principally ascribed to the size of grain,where cast AZ31 and WAAM AZ31 were featured by micro galvanic corrosion and intergranular corrosion,respectively.
基金supported by the Natural Science Foundation of Inner Mongolia Autonomous Region(Grant No.2021MS05049)the Youth Fund Project of State Key Laboratory of Baiyunobo Rare Earth Resource Researches and Comprehensive Utilization(Grant No.2021Z2348)the Project of China North Rare Earth(Group)High-tech Co.,Ltd.(Grant No.2020H2177).
文摘To investigate the effect of rare earth on size and distribution of TiB2 phase in aluminum alloy refiner,Al-5Ti-1B-RE master alloy was fabricated,and its microstructure and phase constitutions were investigated by the combination of first principles calculations and experimental investigation.The calculated results reveal that Ce has the most effective modification ability due to the most positive adsorption energy and the largest charge transfer value compared with other rare earth elements.Results of experimental investigation indicate that the addition of rare earth in the Al-5Ti-1B alloys can greatly refine the particle size of TiB2,improve the distribution of particles and lead to better refinement effect than that of the Al-5Ti-1B alloys without rare earth.Moreover,Ce has the best optimization effect,which agrees well with the calculated results.
文摘The large dual-channel wide-bodied aircraft has a long range and a high cruise Mach number.Therefore,its aerodynamic design requires a high level ofwind tunnel test refinement.Based on the requirements of aerodynamic design for the future wide-bodied aircraft and the characteristics of high-speed wind tunnel tests,the error theory is introduced to analyze the factors affecting the accuracy of the test data.This study carries out a series of research on the improvement of refined aerodynamic test technology in an FL-26 wind tunnel,including design and optimization of the support system of wide-bodied aircraft,model attitude angle measurement,Mach number control accuracy,measurement and control system stability,test data correction and perfection,high-precision force balance and standard model development.In addition,the effect of the standard specification of the refined aerodynamic test is investigated to improve the data quality.The research findings have been applied in the standard model test and subsequent models of wide-bodied aircraft.The results show that whenMach numbers are less than 0.9,the control accuracy of Mach numbers in the FL-26 wind tunnel is smaller than 0.001 and the measurement error of attack angle is smaller than 0.01°.Therefore,it has the ability to correct the data influenced by factors,such as support/wall interference,model deformation,floating resistance and airflow deflection angle.The repeatability accuracy of the standard model’s comparison test shows that the lift coefficient is less than or equal to 0.0012,the drag coefficient is less than or equal to 0.00004,pitching moment coefficient is less than or equal to 0.0004.The bending resolution of the model’s deformation measurement is less than 0.2 mm,and the tensional deformation is smaller than 0.04°.The revised aerodynamic data and model deformation measurement results have good agreement with that of the ETW wind tunnel.The results demonstrate that the improved technology presented in this paper can significantly enhance the refined aerodynamic test of wide-bodied aircraft.
基金Funded by the Basic Research Projects in Shanxi Province(No.202103021224183)。
文摘Both Cu60Ni38Co2 and Cu60Ni40 alloy were naturally cooled after rapid solidification from the liquid phase.The transformation law of the microstructure characteristics of the rapidly solidified alloy with the change of undercooling(DT)was systematically studied.It was found that the two alloys experienced the same transformation process.The refinement structures under different undercoolings were characterized by electron backscatter diffraction(EBSD).The experimental results show that the characteristics of the refinement structure of the two alloys with low undercooling are the same,whereas,the characteristics of the refinement structure with high undercooling are opposite.The transmission electron microscope(TEM)results of Cu60Ni38Co2 alloy show that the dislocation network density of low undercooled microstructure is lower than that of high undercooled microstructure.By combining EBSD and TEM,it can be confirmed that the dendrite remelting fracture is the reason for the refinement of the low undercooled structure,while the high undercooled structure is refined due to recrystallization.
基金supported by Project supported by the Joint Funds of the National Natural Science Foundation of China(Grant No.U20A20230)Natural Science Foundation of Shanxi Province(No.201901D111176)+2 种基金Project supported by the Key R&D program of Shanxi Province(No.2020XXX015)Research Project Supported by Shanxi Scholarship Council of China(2021-127)Graduate Education Innovation Program of Shanxi Province(2022Y579).
文摘The effects of different complex shear stress conditions on grain refinement and texture evolution of Mg-13Gd-4Y-2Zn-0.5Zr alloy were investigated.With increasing strain rate,the average grain size of compression-shear(CS)and compression-torsion(CT)samples are decreased,and the grain size of dynamic recrystallization(DRX)grains is also decreased.This is because that the precipitation number ofβphases is increased,and the hindering effect on grain growth can be significantly enhanced.The DRX fractions of CS and CT samples are decreased with increased strain rate.The low DRX fraction at high strain rate is related to the insufficient time for grains to nucleate.The DRX process can be promoted by the PSN mechanism of second phases,and the grain growth can be restricted by the pinning effect.At the same time,the texture strength is enhanced as the strain rate increased.Besides,the kinking degree of lamellar long-period stacking ordered(LPSO)phases is increased.Under complex shear stress conditions,non-basal slip,especially pyramidal slip,is easily activated and the texture is deflected greatly.Compared with the CS samples,CT samples have smaller average grain size,higher DRX fraction,and lower texture strength for a certain strain rate.This is because that the equivalent stress of the CT sample is larger,the stress triaxiality is smaller,so more serious dislocations are piled up near grain boundaries and second phases.At the same time,since CT sample was sheared with torsion,the dislocation movement path can be called“rotational dislocation accumulation”,and the longer distribution path of the CT sample is generated,so more sub-grains and low-angle grain boundaries(LAGBs)are formed.Compared with the CS sample,more huge-angle grain boundaries(HAGBs)and DRX grains are formed from grain boundary to grain interior,so better grain refinement effect is achieved.
文摘Erratum to:International Journal of Minerals, Metallurgy and MaterialsVolume 28, Number 7, July 2021, Page 1112 The original version of this article unfortunately contained mistakes. Symbols in Table 2 are used incorrectly.
基金supported by National Key Research and Development Program of China (No.2023YFB3710900)National Natural Science Foundation of China (Nos.U2241235,U2167213,51971053)+2 种基金funded by the Project of Promoting Talents in Liaoning province (No.XLYC2203202)the financial assistance from Young Elite Scientists Sponsorship Program by CAST (2019-2021QNRC001,2019-2021QNRC002,2019-2021QNRC003)the fund from the Fundamental Research Funds for the Central Universities (N2202020)。
文摘Low absolute strength becomes one major obstacle for the wider applications of low/no rare-earth(RE) containing Mg alloys. This review firstly demonstrates the importance of grain refinement in improving strength of Mg alloys by comprehensively comparing with other strategy, e.g., precipitation strengthening. Dynamic recrystallization(DRX) plays a crucial role in refining grain size of Mg wrought alloys.Therefore, secondly, the DRX models, grain nucleation mechanisms and the related grain refinement abilities in Mg alloys are summarized,including phase boundary, twin boundary and general boundary induced recrystallization. Thirdly, the newly developed low-RE containing Mg alloy, e.g., Mg-Ce, Mg-Nd and Mg-Sm based alloys, and the RE-free Mg alloys, e.g., Mg-Al, Mg-Zn, Mg-Sn and Mg-Ca based alloy,are reviewed, with the focus on enhancing the mechanical properties mainly via the grain refinement strategy. At the last section, the perspectives and outstanding issues concerning high-performance Mg wrought alloys are also proposed. This review is meant to promote the deep understanding on the critical role of grain refinement in Mg alloys and provide reference for the development of other high strength and low-cost Mg alloys which are fabricated by the conventional extrusion/rolling processing.
基金Funded by the Basic Research Projects in Shanxi Province (202103021224183)。
文摘The molten Cu60Ni35Co5 ternary alloy was undercooled by fluxing method and solidified by natural cooling method.The microstructure of all undercooled samples were analyzed.It is found that the rapidly solidified Cu60Ni35Co5 alloy has undergone two grain refinement phenomena within the undercooling range,and its microstructure and morphology change with the undercooling through the transformation process of“coarse dendrite-equiaxed dendrite-oriented fine dendrite-equiaxed crystal”.The refined structure with the maximum undercooling?T of 253 K was selected for electron backscatter diffraction(EBSD)and transmission electron microscopy(TEM)tests.EBSD results show that the refined structure contains a high proportion of large angle grain boundaries(LAGBs),a large number of randomly oriented grains,and high proportion of twins,while TEM results show that the dislocation density in most areas is relatively low.The above characteristics confirm that the solidification structure is refined due to recrystallization behavior under high undercooling.
基金supported by the National Natural Science Foundation of China (Grant Nos.U2037601,51821001,and 52105348)the Natural Science Foundation for Young of Jiangsu Province (Grant No.BK20190863)the Research Program of Joint Research Center of Advanced Spaceflight Technologies (No.USCAST2020-31)。
文摘High-performance cast magnesium rare-earth(Mg-RE) alloys are one of the most important materials among all developed Mg alloy families, and have shown great potential in military and weapons, aerospace and aviation, orthopedic implants, etc. Controlling grain size and distribution of it is key to the promising mechanical performance of Mg-RE alloy casting components. During the casting of a real component, nearly every procedure in the fabrication process will influence the grain refinement effect. The procedure may include and may not be limited to the chemical inoculations, possibly applied physical fields, the interfere between grain refiner and purifications, and the casting techniques with different processing parameters. This paper reviews the recent advances and proposed future developments in these categories on grain refinement of cast Mg-RE alloys. The review will provide insights for the future design of grain refinement techniques,the choosing of processing parameters, and coping strategies for the failure of coarsening for cast Mg-RE components with high quality and good performance.
基金Funded by the Basic Research Projects in Shanxi Province(202103021224183)。
文摘Both Cu60Ni38Co2 and Cu60Ni40 alloy were naturally cooled after rapid solidification from the liquid phase.The transformation law of the microstructure characteristics of the rapidly solidified alloy with the change of undercooling(ΔT)was systematically studied.It is found that the two alloys experience the same transformation process.The refinement structures under different undercoolings were characterized by electron backscatter diffraction(EBSD).The results show that the characteristics of the refinement structure of the two alloys with low undercooling are the same,but the characteristics of the refinement structure with high undercooling are opposite.The transmission electron microscopy(TEM)results of Cu60Ni38Co2 alloy show that the dislocation network density of low undercooled microstructure is lower than that of high undercooled microstructure.By combining EBSD and TEM,it could be confirmed that the dendrite remelting fracture is the reason for the refinement of the low undercooled structure,while the high undercooled structure is refined due to recrystallization.On this basis,in the processing of copper base alloys,there will be serious work hardening phenomenon and machining hard problem of consciousness problems caused by excessive cutting force.A twodimensional orthogonal turning finite element model was established using ABAQUS software to analyze the changes in cutting speed and tool trajectory in copper based alloy ultrasonic elliptical vibration turning.The results show that in copper based alloy ultrasonic elliptical vibration turning,cutting process parameters have a significant impact on cutting force.Choosing reasonable process parameters can effectively reduce cutting force and improve machining quality.
文摘The Al-5Cu alloys were prepared by different treatment methods,including adding a refiner Al-5Ti-1B,exerting a rotating magnetic field(RMF),and compound treatment of both refiner and RMF.The effects of treatment methods on the microstructure,properties,and solid solubility of the Al-5Cu alloy were investigated.The optimal magnetic field parameters and addition amount of refiner were confirmed by experiment.Results show that either RMF or adding refiner Al-5Ti-1B alone can refine the grain size,and the refining effect can be further improved by a compound refining treatment with optimized magnetic field parameters(120 A current and 8 Hz frequency) and 1.0wt.% Al-5Ti-1B refiner(RMF*+Al-5Ti-1B*).The average grain size is decreased to 68.1 μm,which is 60.8%,21.1%,and 83.5% lower than that of the alloy treated by the optimized rotating magnetic field,the Al-5Ti-1B refiner,and the alloy without any treatment,respectively.The tensile strength and elongation of the alloy reach 232.5 MPa and 18.6%,respectively,which are obviously higher than those of the alloys treated by rotating magnetic field,Al-5Ti-1B refiner,and the alloy without any treatment,respectively.Additionally,the solid solubility of the alloy is also obviously improved compared to the alloys treated by other methods.
基金supported by the National Science Fund for Distinguished Young Scholars(Grant No.52125904)the National Natural Science Foundation of China(Grant No.51979224)the Program 2022TD-01 for Shaanxi Provincial Innovative Research Team(Grant No.2022TD-01)。
文摘Overtopping is one of the main reasons for the breaching of concrete-face sand-gravel dams(CFSGDs).In this study,a refined mathematical model was established based on the characteristics of the overtopping breaching of CFSGDs.The model characteristics were as follows:(1)Based on the Renormailzation Group(RNG)k-εturbulence theory and volume of fluid(VOF)method,the turbulent characteristics of the dam-break flow were simulated,and the erosion surface of the water and soil was tracked;(2)In consideration of the influence of the change in the sediment content on the dam-break flow,the dam material transport equation,which could reflect the characteristics of particle settlement and entrainment motion,was used to simulate the erosion process of the sand gravels;(3)Based on the bending moment balance method,a failure equation of the concrete face slab under dead weight and water load was established.The proposed model was verified through a case study on the failure of the Gouhou CFSGD.The results showed that the proposed model could well simulate the erosion mode of the special vortex flow of the CFSGD scouring the support body of the concrete face slab inward and reflect the mutual coupling relationship between the dam-break flow,sand gravels,and concrete face slabs.Compared with the measured values,the relative errors of the peak discharge,final breach average width,dam breaching duration,and maximum failure length of the face slab calculated using the proposed model were all less than 12%,thus verifying the rationality of the model.The proposed model was demonstrated to perform better and provide more detailed results than three selected parametric models and three simplified mathematical models.The study results can aid in establishing the risk level and devising early warning strategies for CFSGDs.