Microstructures and mechanical properties of extruded 2024 aluminum alloy reinforced by FeNiCrCoAl_3 particles

Different proportions of commercial 2024 aluminum alloy powder and FeNiCrCoA13 high entropy alloy （HEA） powder were ball-milled （BM） for different time. The powder was consolidated by hot extrusion method. The microstructures of the milled powder and bulk alloy were examined by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. Mechanical properties of the extruded alloy were examined by mechanical testing machine. The results show that after BM, the particle size and microstructures of the mixed alloy powder change obviously. After 48 h BM, the average size of mixed powder is about 30 nm, and then after hot extrusion, the average size of grains reaches about 70 rim. The compressive strength of the extruded alloy reaches 710 MPa under certain conditions of milling time and composition. As a result of the identification of the nano-/micro-strueture-property relationship of the samples, such high strength is attributed mainly to the nanocrystalline grains of a（Al） and nanoscaled FeNiCrCoAl3 particles, and the fine secondary phase of Al2Cu and Fe-rich phases.

Fabrication and Mechanical Properties of 2024 Aluminum Alloy Reinforced by FeNiCrCoAl_3 High Entropy Particles

This article mainly discussed bulk material lHvl^ared by powder metallurgy, and the commercial 2024 aluminum alloy powder and FeNiCrCoA13 high entropy alloy powder （both produced by argon gas atomization process） were ball-milled for different hours. The prepared powder was consolidated by hot extrusion method. The microstruetures of the milled powder and bulk alloy were examined by X - Ray Diffraction （XRD）, Scanning Electron Microscopy （SEM） and Transmission Electron Microscopy （TEM）. The thermal stability was tested by differential scanning calorimetry （DSC）. Mechanical properties of the extruded alloy were examined by Vickers hardness tester and mechanical testing machine. The results show that after milling, the mixed particle sizes and microstructures of the alloy powder change obviously. The compressive strength of the extruded alloy has reached 580 MPa under certain conditions of milling time and composition.

Effects of TaN nanoparticles on microstructure,mechanical properties and tribological performance of PEEK coating prepared by electrophoretic deposition

In order to solve the friction,wear and lubrication problems of titanium,a series of TaN/ployether−ether−ketone(PEEK)coatings were developed by electrophoretic deposition,and the effects of TaN nanoparticles on the microstructure,mechanical properties and tribological performance of coatings were explored.Results manifest that the introduction of TaN nanoparticles into PEEK coatings could improve the deposition efficiency,enhance the resistant deform capacity,increase the hardness,elastic modulus and adhesive bonding strength.Compared with the pure PEEK coating,the friction coefficient of P-TN-3 was greatly reduced by 31.25%.The wear resistance of P-TN-3 was also improved in huge boost,and its specific wear rate was decreased from 9.42×10^(−5) to 1.62×10^(−5) mm^(3)·N^(−1)·m^(−1).The homogeneous composite TaN/PEEK coatings prepared by electrophoretic deposition were well-adhered to the titanium alloy substrate,TaN nanoparticles could improve the strength of PEEK coating,and provide wear-resistance protection for titanium alloys.

Effective Elastic Properties of 3-Phase Particle Reinforced Composites with Randomly Dispersed Elastic Spherical Particles of Different Sizes Dedicated to Professor Karl Stark Pister for his 95th birthday

Higher-order multiscale structures are proposed to predict the effective elastic properties of 3-phase particle reinforced composites by considering the probabilistic spherical particles spatial distribution,the particle interactions,and utilizing homogenization with ensemble volume average approach.The matrix material,spherical particles with radius a1,and spherical particles with radius a2,are denoted as the 0th phase,the 1st phase,and the 2nd phase,respectively.Particularly,the two inhomogeneity phases are different particle sizes and the same elastic material properties.Improved higher-order(in ratio of spherical particle sizes to the distance between the centers of spherical particles)bounds on effective elastic properties of 3-phase particle reinforced proposed Formulation II and Formulation I derive composites.As a special case,i.e.,particle size of the 1st phase is the same as that of the 2nd phase,the proposed formulations reduce to 2-phase formulas.Our theoretical predictions demonstrate excellent agreement with selected experimental data.In addition,several numerical examples are presented to demonstrate the competence of the proposed frameworks.

Laser cladding in-situ carbide particle reinforced Fe-based composite coatings with rare earth oxide addition

Particulate reinforced metal matrix composite(PR-MMC) has excellent properties such as good wear resistance,corrosion resistance and high temperature properties.Laser cladding is usually used to form PR-MMC on metal surface with various volume fractions of ceramic particles.Recent literatures showed that laser melting of powder mixture containing carbon and carbide-forming elements,was favorable for the formation of in-situ synthesized carbide particles.In this paper,rare earth oxide(RE2O3) was added into t...

Effect of sintering parameters on the microstructure and thermal conductivity of diamond/Cu composites prepared by high pressure and high temperature infiltration

Pure Cu composites reinforced with diamond particles were fabricated by a high pressure and high temperature （HPHT） infiltration technique. Their microstructural evolution and thermal conductivity were presented as a function of sintering parameters （temperature, pressure, and time）. The improvement in interfacial bonding strength and the maximum thermM conductivity of 750 W/（m.K） were achieved at the optimal sintering parameters of 1200℃, 6 GPa and 10 min. It is found that the thermal conductivity of the composites depends strongly on sintering pressure. When the sintering pressure is above 6 GPa, the diamond skeleton is detected, which greatly contributes to the excellent thermal conductivity.

Influence of Ta on Microstructure and Abrasive Wear Resistance of Laser Clad NiCrSiB Coating

A mixture of NiCrSiB alloy powder and tantalum （Ta） powder was used as laser clad material to improve abrasive wear resistance of the Ni-based coating. The microstructure and wear resistance of the coating were investigated. Addition of Ta element works to suppress the growth of coarse M7C3 carbide in the coating, resulting in a decrease in aspect ratio of coarse carbide. In the abrasive wear test, in situ synthesized TaC particles well bond with Ni-based matrix, and are hardly pull out from wear surface. Grooves on the worn surface of NiCrSiB coating are much deeper and sharper than those in the NiCrSiB＋Ta composite coating. Also, a weight loss of the composite coating is much lower than that of the NiCrSiB coating. The wear resistance of the laser clad Ni-based coating is enhanced to a much greater extent through the addition of Ta. This is attributed to the in situ synthesized hard TaC particles of nearly equiaxed shape, the Ni-based matrix strengthened by Ta and the decrease in aspect ratio of the coarse brittle carbides.

Microstructure of in situ Al_3Ti/6351Al composites fabricated with electromagnetic stirring and fluxes

The 6351 wrought aluminum alloy and K2TiF6-CaF2-LiCl components were selected as raw materials to fabricate in situ Al3Ti particulate reinforced aluminum alloy at 720℃via direct melt reaction method with electromagnetic stirring(EMS).CaF2 and LiCl acted as fluxes to lower the reaction temperature of the system.It is shown that the electromagnetic stirring and fluxes accelerate the emulsion process of K2TiF6.Optical microscopy,scanning electron microscopy,transmission electron microscopy and energy dispersive spectrum were utilized to analyze the microstructure and components of composites.Compared to composites fabricated without EMS and fluxes,the sizes of endogenetic Al3Ti are refined from 10-15μm to 2-4μm,which are often accompanied with silicon element.The morphology of Al3Ti or Al3TiSi0.22 exhibits triangle,quadrilateral and other clumpy patterns. Because of the Ca elements from CaF2,the sizes of Mg2Si decrease from 8-10μm to 1-2μm due to the formation of Ca2Si.

Processing of nanostructured metallic matrix composites by a modified accumulative roll bonding method with structural and mechanical considerations

Particulate reinforced metallic matrix composites have attracted considerable attention due to their lightweight, high strength, high specific modulus, and good wear resistance. A1/B4C composite strips were produced in this work by a modified accumulative roll bonding process where the strips were rotated 90° around the normal direction between successive passes. Transmission electron microscopy and X-ray diffraction analyses reveal the development of nanostructures in the Al matrix after seven passes. It is found that the B4C reinforcement distribution in the matrix is improved by progression of the process. Additionally, the tensile yield strength and elongation of the processed materials are increased with the increase of passes.

Solid fraction evolution characteristics of semi-solid A356 alloy and in-situ A356–TiB_2 composites investigated by differential thermal analysis

The key factor in semi-solid metal processing is the solid fraction at the forming temperature because it affects the microstructure and mechanical properties of the thixoformed components. Though an enormous amount of data exists on the solid fraction-temperature re- lationship in A356 alloy, information regarding the solid fraction evolution characteristics of A356-TiB2 composites is scarce. The present article establishes the temperature-solid fraction correlation in A356 alloy and A356-xTiB2 （x = 2.5wt% and 5wt%） composites using dif- ferential thermal analysis （DTA）. The DTA results indicate that the solidification characteristics of the composites exhibited a variation of 2℃ and 3℃ in liquidus temperatures and a variation of 3℃ and 5℃ in solidus temperatures with respect to the base alloy. Moreover, the eutectic growth temperature and the solid fraction（fs） vs. temperature characteristics of the composites were found to be higher than those of the base alloy. The investigation revealed that in-situ formed TiB2 particles in the molten metal introduced more nucleation sites and reduced undercooling.

STUDY ON DIFFUSION WELDING OF ALUMINIUN MATRIX COMPOSITE

Effects of diffusion welding parameters on strength of welded joint based on particle reinforced alumini- um matrix composite Al2O3p/6061Al were studied by comparing with aluminium matrix alloy,Mecha- nism for the loss of joint strength was analyzed.It was pointed out that the key processing parameters affecting the strength of joint was the welding temperature.The high quality joint can be successfully obtained with appropriate diffusion welding parameters.

Study on dry friction and wear resistance of a WC-Co particle reinforced iron matrix composite material

In order to select a suitable material for the rolling mill guide application, the dry sliding friction and wear resistance of a tungsten carbide combining cobalt (WC-Co) particle reinforced chromium cast iron composite material were studied. In particular, the wear resistance was discussed in detail. The results showed that the composite material demonstrates 25 times the wear resistance of high Cr cast iron, and 9 times the wear resistance of heat resistant steel. However, the average friction factor in the stable friction stage showed a relationship of μComposites/45#steel>μHigh chromium cast iron/45#steel>μHeat resistant steel/45 # steel. The wear resistance mechanism of the composite material was associated with the reinforcing particles, which protruded from the worn surface to bear the friction load when the matrix material surface was worn, thereby reducing the abrasive and adhesive wear. In addition, the matrix material possessed suitable hardness and toughness, providing a support to the reinforcements.

AN ANALYSIS OF THE MODELING OF STRESS AND STRAIN FIELDS IN A REAL MICROSTRUC-TURE USING AHYBRID METHOD

The distribution of stress and strain fields in a micro-structuralarea of a particle reinforced composite is studied by a combinationof experimental and numerical method (hybrid method). With the ex-perimental values of displacements in a micro-region as the boundaryloading condition, strain and stress fields inside the micro-regionare calculated by the finite element method under tow different kindsof model- ing, namely, as pale stress and plane strain condition. Thedifferences between the two kinds of modeling conditions as appliedto micro-structural areas are discussed.

Fabrication and densification enhancement of SiC-particulate-reinforced copper matrix composites prepared via the sinter-forging process

The fabrication of copper （Cu） and copper matrix silicon carbide （Cu/SiCp） particulate composites via the sinter-forging process was investigated. Sintering and sinter-forging processes were performed under an inert Ar atmosphere. The influence of sinter-forging time, temperature, and compressive stress on the relative density and hardness of the prepared samples was systematically investigated and subsequently compared with that of the samples prepared by the conventional sintering process. The relative density and hardness of the composites were enhanced when they were prepared by the sinter-forging process. The relative density values of all Cu/SiCp composite samples were observed to decrease with the increase in SiC content.

Synergistic regulation of current-carrying wear performance of resin matrix carbon brush composites with tungsten copper composite powder

Resin matrix carbon brush composites(RMCBCs)are critical materials for high-powered electric tools.However,effectively improving their wear resistance and heat dissipation remains a challenge.RMCBCs prepared with flake graphite powders that were evenly loaded with tungsten copper composite powder(RMCBCs-W@Cu)exhibited a low wear rate of 1.63 mm^(3)/h,exhibiting 48.6%reduction in the wear rate relative to RCMBCs without additives(RMCBCs-0).In addition,RMCBCs-W@Cu achieved a low friction coefficient of 0.243 and low electric spark grade.These findings indicate that tungsten copper composite powders provide particle reinforcement and generate a gradation effect for the epoxy resin(i.e.,connecting phase)in RMCBCs,which weakens the wear of RMCBCs caused by fatigue under a cyclic current-carrying wear.

Influence of filler materials on microstructure and mechanical properties of MGH956 alloy in TIG welding

In order to improve the mechanical properties of MGH956 alloy fusion weZding joint, two kinds of self-made materials were used as filler materials to MGH956 alloy for TIG welding respectively. Microstracture and tensile fracture of joints were researched by scanning electron microscope（SEM）. Reinforced particles were researched by SEM, X-ray diffraction （ XRD ） and energy dispersive X-ray spectrometry （EDS）. These results were compared with joint which is filled with base materials. The results show that new reinforced phases such as TiC, TiN, Ni3Al and A1Ni are produced in the weld metal zone with two kinds of self-made materials as filler materials. The size of these reinforcements is about 1 μm, and the distribution of particles is very uniform in the matrix. The number of pores is reduced. Agglomerate Al-Y-O composite oxides are correspondingly decreased compared to the joint filled with base material. Thus, welded joint perormanee is enhanced. The average room temperature tensile strength of joints are 581 MPa and 607 MPa respectively. The fracture of joints both in general exhibit brittle fracture.

Effects of sintering temperature on the microstructural evolution and wear behavior of WCp reinforced Ni-based coatings

This article focuses on the microstructural evolution and wear behavior of 50wt%WC reinforced Ni-based composites prepared onto 304 stainless steel substrates by vacuum sintering at different sintering temperatures. The microstructure and chemical composition of the coatings were investigated by X-ray diffraction （XRD）, differential thermal analysis （DTA）, scanning and transmission electron microscopy （SEM and TEM） equipped with energy-dispersive X-ray spectroscopy （EDS）. The wear resistance of the coatings was tested by thrust washer testing. The mechanisms of the decomposition, dissolution, and precipitation of primary carbides, and their influences on the wear resistance have been discussed. The results indicate that the coating sintered at 1175℃ is composed of fine WC particles, coarse M6C （M=Ni, Fe, Co, etc.） carbides, and discrete borides dispersed in solid solution. Upon increasing the sintering temperature to 1225℃, the microstructure reveals few incompletely dissolved WC particles trapped in larger M6C, Cr-rich lamellar M23C6, and M3C2 in the austenite matrix. M23C6 and M3C2 precipitates are formed in both the γ/M6C grain boundary and the matrix. These large-sized and lamellar brittle phases tend to weaken the wear resistance of the composite coatings. The wear behavior is controlled simultaneously by both abrasive wear and adhesive wear. Among them, abrasive wear plays a major role in the wear process of the coating sintered at 1175℃, while the effect of adhesive wear is predominant in the coating sintered at 1225℃.

Study on Diffusion Welding Parameters of Particle reinforced Aluminium Matrix Composite Al_2O_(3p) /6061Al

Effects of diffusion welding process parameters on strength of welded joint based on particle reinforced aluminium matrix composite Al 2O 3p /6061Al have been studied through comparing with aluminium matrix alloy. The mechanism for loss of joint strength has been analyzed. It should be pointed out that key processing parameters affecting the strength of joint was welding temperature. The high quality joint can be successfully obtained with appropriate diffusion welding parameters.

Hypereutectic Al-Si Matrix Composites Prepared by In Situ Fe_(2)O_(3)/Al System

Al_(2)O_(3) particles reinforced hypereutectic Al-Si composites were prepared by in situ Fe_(2)O_(3)/Al reaction system.The thermodynamic analysis and microstructure evolution were investigated by differential scanning calorimetry,optical microscope,scanning electronic microscopy and transmission electron microscope.Results show that the reaction between Fe_(2)O_(3) and Al is spontaneous which can be separated into two steps at different temperatures.The in situ Al_(2)O_(3) particles in nano size distribute on the Al matrix accompanied with long needle-shapedβFe-rich intermetallic phase.With different content of Mn addition,βphase can be modified toα-Al15(Mn,Fe)3Si2 andδ-Al4(Fe,Mn)Si2.Both tensile strength and elongation results at room temperature and 300℃reveal that the optimal Fe-rich intermetallic phase is finer Chinese-script and polyhedralαphase with a Mn/Fe mass ratio 0.5 for the composites.Both in situ Al_(2)O_(3) particles andα-Fe phases contribute to the properties improvement of the composites。

THEORETICAL ANALYSIS ON THE LOCAL CRITICAL STRESS AND SIZE EFFECT FOR INTERFACIAL DEBONDING IN PARTICLE REINFORCED RHEOLOGICAL MATERIALS

The mechanisms of interfacial debonding of particle reinforcedrheological materials are studied. Based on an energy criterion, asimple formula of local critical stress for interfacial debonding isderived and expressed in terms of the interfacial energy. Theparticle size effect on interface debond- ing can then be analyzedeasily owing to the fact that critical stress is inverselyproportional to the square root of particle radius. By takingPP/CaCO_3 system as an example, the present energy criterion iscompared with the mechanical debonding criterion, and it is foundthat under the condition that bond strength is equal to matrixstrength and particle radius not over 0.2μm, the mechanicaldebonding cri- terion can be automatically satisfied if the energycirterion is satisfied.