Research on Indoor Passive Positioning Technology Based on WiFi

In recent years,WiFi indoor positioning technology has become a hot research topic at home and abroad.However,at present,indoor positioning technology still has many problems in terms of practicability and stability,which seriously affects the accuracy of indoor positioning and increases the complexity of the calculation process.Aiming at the instability of RSS and the more complicated data processing,this paper proposes a low-frequency filtering method based on fast data convergence.Low-frequency filtering uses MATLAB for data fitting to filter out low-frequency data;data convergence combines the mean and multi-data parallel analysis process to achieve a good balance between data volume and system performance.At the same time,this paper combines the position fingerprint and the relative position method in the algorithm,which reduces the error on the algorithm system.The test results show that the strategy can meet the requirements of indoor passive positioning and avoid a large amount of data collection and processing,and the average positioning error is below 0.5 meters.

Impact of sampling interval on variance components of epoch-wise residual error in relative GPS positioning: A case study of a 40-km-long baseline

The study presents sampling interval impacts on variance components of the epoch-wise residual errors in relative GPS positioning. In the variance components estimation process, the 2-way nested ANOVA method was used. For that purpose, GPS observation data during four months at two permanent GPS stations, establishing a 40-km-long baseline as a part of the Montenegrin permanent network(Monte Pos), were used. The study results showed that there is no statistically significant impact of sampling interval changes on epoch-wise variance components related to the residual tropospheric and ionospheric delays(effect a) when it comes to such a baseline. However, it is not the case with epoch-wise variance components related to the interstation-distance-independent residual ‘far-field’ multipath effect(effect b). It turned out that the absolute values of relative differences of standard deviations of the effect a on the relative GPS coordinates(e, n and u) had maximum values 11.1%, 10.2% and 8.9%,respectively. Keeping the same order of presentation for the effect b, the values of 5.9%, 9.9% and 12.5%were obtained. In addition, absolute values of relative differences of standard deviations of horizontal and vertical position had maximum values of 3.8% and 7.7%, respectively.

Dependence of epoch-wise two-way nested ANOVA estimates of variances of unmodeled effects present in relative GPS positioning on satellite elevation cutoff angle and PDOP mask

Impact of satellite elevation cutoff angle and position dilution of precision(PDOP)mask change on epoch-wise variance components of unmodeled effects that accompany relative Global Positioning System(GPS)positioning is presented herein.Data used for this study refer to the winter and summer periods of the years with minimal(2008)and maximal(2013)solar activity.These data were collected every 30 s in static mode,at two permanent GPS stations located in Montenegro,establishing a mediumdistance(116-km-long)baseline with a height difference of approximately 760 m between its endpoints.The study showed that changing satellite elevation cutoff angle,with a fixed PDOP mask,affects epochwise two-way nested ANOVA estimates of variances related to the‘far-field’multipath(considered as the nested factor herein)and the combined unmodeled effect of tropospheric and ionospheric refraction(considered as the nesting factor herein).However,changing of PDOP mask,with a fixed satellite elevation cutoff angle,doesn’t affect epoch-wise two-way nested ANOVA estimate of variance of the combined unmodeled effect of tropospheric and ionospheric refraction,but,generally,affects the estimate of variance of the‘far-field’multipath(possibly mixed with a part of a‘shorter-term’ionospheric refraction),which is especially pronounced for the summer period.It should also be noted that there is a significant influence of satellite elevation cutoff angle change on both epoch-wise horizontal and vertical position accuracy,only for the summer period,especially in the presence of maximal solar activity,while there is no significant impact of PDOP mask change on epoch-wise positional accuracy.

Reference satellite selection method for GNSS high-precision relative positioning

Selecting the optimal reference satellite is an important component of high-precision relat/ve positioning because the reference satellite directly influences the strength of the normal equation. The reference satellite selection methods based on elevation and positional dilution of precision （PDOP） value were compared. Results show that all the above methods cannot select the optimal reference satellite. We introduce condition number of the design matrix in the reference satellite selection method to improve structure of the normal equation, because condition number can indicate the ill condition of the normal equation. The experimental results show that the new method can improve positioning accuracy and reliability in precise relative positioning.

NOTES ON THE LOG-BRUNN-MINKOWSKI INEQUALITY

Böröczky-Lutwak-Yang-Zhang proved the log-Brunn-Minkowski inequality for two origin-symmetric convex bodies in the plane in a way that is stronger than for the classical Brunn-Minkowski inequality.In this paper,we investigate the relative positive center set of planar convex bodies.As an application of the relative positive center,we prove the log-Minkowski inequality and the log-Brunn-Minkowski inequality.

Relative-Position Estimation Based on Loosely Coupled UWB–IMU Fusion for Wearable IoT Devices

Relative positioning is one of the important techniques in collaborativerobotics, autonomous vehicles, and virtual/augmented reality (VR/AR)applications. Recently, ultra-wideband (UWB) has been utilized to calculaterelative position as it does not require a line of sight compared to a camerato calculate the range between two objects with centimeter-level accuracy.However, the single UWB range measurement cannot provide the relativeposition and attitude of any device in three dimensions (3D) because oflacking bearing information. In this paper, we have proposed a UWB-IMUfusion-based relative position system to provide accurate relative positionand attitude between wearable Internet of Things (IoT) devices in 3D. Weintroduce a distributed Euler angle antenna orientationwhich can be equippedwith the mobile structure to enable relative positioning. Moving average andmin-max removing preprocessing filters are introduced to reduce the standarddeviation. The standard multilateration method is modified to calculate therelative position between mobile structures. We combine UWB and IMUmeasurements in a probabilistic framework that enables users to calculatethe relative position between two nodes with less error. We have carried outdifferent experiments to illustrate the advantages of fusing IMU and UWBranges for relative positioning systems. We have achieved a mean accuracy of0.31m for 3D relative positioning in indoor line of sight conditions.

PCATNet: Position-Class Awareness Transformer for Image Captioning

Existing image captioning models usually build the relation between visual information and words to generate captions,which lack spatial infor-mation and object classes.To address the issue,we propose a novel Position-Class Awareness Transformer(PCAT)network which can serve as a bridge between the visual features and captions by embedding spatial information and awareness of object classes.In our proposal,we construct our PCAT network by proposing a novel Grid Mapping Position Encoding(GMPE)method and refining the encoder-decoder framework.First,GMPE includes mapping the regions of objects to grids,calculating the relative distance among objects and quantization.Meanwhile,we also improve the Self-attention to adapt the GMPE.Then,we propose a Classes Semantic Quantization strategy to extract semantic information from the object classes,which is employed to facilitate embedding features and refining the encoder-decoder framework.To capture the interaction between multi-modal features,we propose Object Classes Awareness(OCA)to refine the encoder and decoder,namely OCAE and OCAD,respectively.Finally,we apply GMPE,OCAE and OCAD to form various combinations and to complete the entire PCAT.We utilize the MSCOCO dataset to evaluate the performance of our method.The results demonstrate that PCAT outperforms the other competitive methods.

DUAL QUATERNION CURVE INTERPOLATION ALGORITHM FOR FORMATION SATELLITES

The traditional algorithms for formation flying satellites treat the satellite position and attitude sepa- rately. A novel algorithm combining satellite attitude with position is proposed. The principal satellite trajectory is obtained by dual quaternion interpolation, then the relative position and attitude of the deputy satellite are ob- tained by dual quaternion modeling on the principal satellite. Through above process, relative position and atti- tude are unified. Compared with the orbital parameter and the quaternion methods, the simulation result proves that the algorithm can unify position and attitude, and satisfy the precision requirement of formation flying satel- lites.

Influence of Heterojunction Position on SiGe HBTs with Graded BC Junctions

The influence of a heterojunction in the vicinity of a graded BC junction on the performance of npn SiGe HBTs is studied. SiGe HBTs differing only in heterojunction position in the vicinity of a graded BC junction are simulated by means of 2D Medici software for DC current gain and frequency characteristics. In addition, the simulated DC current gains and cut-off frequencies are compared at different collector-emitter bias voltages. Through the simulation results, both DC and HF device performance are found to be strongly impacted by degree of confinement of the neutral base in the SiGe layer, even in the absence of a conduction band barrier. This conclusion is of significance for designing and analyzing SiGe HBTs.

PRINCIPLE,SOFTWARE AND EXPERIMENT OF GPS-SUPPORTED AEROTRIANGULATION

In conventional aerial photogrammetry, the high accurate photogrammetric point determination is always carried out by aerotriangulation using a great deal of ground control points around the perimeter and in the center of block area because the exterior orien- tation parameters of aerial photographs are unknown. A technological revolution in pho- togrammetry has taken place since Navstar global positioning system (GPS) was applied to determine the 3D coordinates of exposure station positions during the photo flight missions. GPS-supported aerotriangulation is conducted by a combined bundle adjustment for pho- togrammetric observations and the camera orientation data. In this case, the essential ground control points are replaced by GPS-determined camera positions. Recent investigations show this method is coming to the practice. We have been engaged in the theoretical studies, soft- ware development, and related experiments and production in the field since 1990. So far the abundant research achievements are obtained in terms of the theory and application. In this paper,we first derives the mathematical model of GPS-supported aerotriangulation from the geometry between camera and airborne GPS antenna, then describes briefly a software pack- age WuCAPS (Wuhan combined adjustment program system) developed newly by the au- thor,which serves the purpose of the combined bundle adjustment for photogrammetric and non-photogrammetric observations. At the end of the present work, a set of actual aerial pho- tographs,at the image scale of 1: 34 000, with airborne GPS data taken from Tianjing site, China were processed by WuCAPS. The empirical results have verified that the accuracy of the combined bundle adjustment with 4 XYZ ground control points around the corners of block area is very close to that of the conventional bundle adjustment with 3 additional pa- rameters, that leads to reduce 88% field survey and 75% production cost, and can meet the specification of topographic mapping at small or medium scale by GPS-supported aerotriangu- lation without ground control. This shows the ample applicability and the economic benefit of kinematic GPS relative positioning in high accurate photogrammetric point determination.

Influence of relative positions between RF coil and crucible on sapphire crystals by edge-defined film-fed growth(EFG) technique

To obtain the stable temperature field required for growing sapphire crystals, the influence of relative positions between RF coil and crucible on the performances of sapphires produced by edge-defined film-fed growth（EFG） technique was investigated. For comparison, the crucible was located at the top（case A） and the middle（case B） of the RF coil, respectively. Furthermore, the lattice integrities were studied by the double-crystal X-ray diffraction, and the dislocations were observed under the optical microscope and atomic force microscope after corroding in molten KOH at 390 ℃. The crystals in case B exhibit better lattice integrity with smaller full width at half maximum of 29.13 rad·s, while the value in case A is 45.17 rad·s. The morphologies of dislocation etch pits in both cases show typical triangular symmetry with smooth surfaces. However, the dislocation density of 2.8×104 cm-2 in case B is only half of that in case A, and the distribution is more uniform, compared to the U-shaper in case A.

Numerical Investigation on the Secondary Flow Control by Using Splitters at Different Positions with Respect to the Main Blade

In turbomachinery,strong secondary flow can produce significant losses of total pressure near the endwall and reduce the efficiency of the considered turbomachine.In this study,splitters located at different positions with respect to the main blade have been used to reduce such losses and improve the efficiency of the outlet guide vane(OGV).Three different relative positions have been considered assuming a NACA 65-010 profile for both the main blade and the splitter.The numerical results indicate that splitters can effectively reduce the total pressure loss by suppressing the secondary flow around the main blade,but the splitters themselves also produce flow losses,which are caused by flow separation effects.

Influence of Inner/Outer Stator Pole Ratio and Relative Position on Electromagnetic Performance of Partitioned Stator Switched Flux Permanent Magnet Machines

Based on the 6-pole outer stator(armature winding-stator),the influence of inner(permanent magnet-stator)/outer stator pole ratio n(n=NIS/NOS),stator relative positions and rotor pole number combinations on electromagnetic performance of partitioned stator switched flux permanent magnet(PM)machines(PS-SFPMMs)is investigated in this paper.Since the armature windings and PMs are located in two separated stators and PMs are stationary,PS-SFPMMs have high fault tolerance capabilities.To maximize the torque performance,the PM of inner stator pole should be aligned with outer stator pole when n is odd while the iron rib of inner stator pole should be aligned with outer stator pole when n is even.No matter what n is selected,the rotor pole number NR can be any integers except the phase number and its multiples.The analysis results indicate that the optimal NR is closed to(NIS+NOS)/2 and it is odd when n is odd while it is even when n is even.Meanwhile,symmetrical phase back-EMF waveform will be obtained when the ratio of Min(NOS,NIS)to the greatest common divisor of Min(NOS,NIS)and NR is even.Based on the optimal rotor pole numbers for 6-pole outer stator with different n and corresponding optimal relative position together with same rated copper loss,the average torque is improved by 18.4%,25.1%and 25.7%respectively in PS-SFPMMs with n equal to 2,3 and 4 when compared with PS-SFPMM with n equal to 1.The analyses are validated by experiment results of the prototype machine.

Dark Matter Creation and Anti-Gravity Acceleration of the Expanding Universe

Dark matter is identified as negative relative energy between quarks in proton and is generated in cold hydrogen gas with pressure gradient in gravitational field. Positive relative energy PRE can be generated between quarks in protons in cold hydrogen gas in outskirts of the universe. The mechanisms for such creation of dark matter and PRE are reviewed and updated in greater detail and clearer manner. The so-generated dark matter in a galaxy can account for the galaxy’s rotation curve. Star formation in this galaxy uses up the hydrogen atoms and thereby reduces its dark matter content. Dark matter created in intergalactic hydrogen gas can form filaments. In a hypothetical model of the universe, a hydrogen atom with a small amount of negative relative energy or dark matter at the outskirts of this universe can via collisions with other atoms turn into one with a small positive relative energy PRE. Once such a sign change takes place, gravitational attraction switches to anti-gravity repulsion unopposed by any pressure gradient. This leads to a “run away” hydrogen atom moving away from the mass center of the universe and provides a basic mechanism for the accelerating expansion of the universe. This theoretical expansion and the measured redshift data are both compatible with the conception of an acceleratingly expanding universe and complement each other. But they cannot verify each other directly because the present model has been constructed for purposes different from those of the measurements. But it can be shown that both approaches do support each other qualitatively under certain circumstances for small velocities. Dark matter and PRE in the present model are not foreign objects like WIMPs and dark energy-cosmological constant but can only be created in cold hydrogen gas in gravitational field. To achieve this, infrequent collisions among the hydrogen atoms must take place. Dark matter was created first and can eventually later evolve into PRE in the outskirts of the universe and in the intergalactic void. Dark matter and PRE will disappear if the hydrogen atom carrying them becomes ionized as in stars.

Soil Atterberg Limits and Consistency Indices as Influenced by Land Use and Slope Position in Western Iran

Atterberg limits and consistency indices are used for classifications of cohesive(fine-grained) soils in relation with compaction and tillage practices. They also provide information for interpreting several soil mechanical and physical properties such as shear strength, compressibility, shrinkage and swelling potentials. Although, several studies have been conducted regarding the land use effects on various soil mechanical properties, little is known about the effects of land use and slope positions on Atterberg limits and consistency indices. This study was conducted to investigate the effects of land use and slope position on selected soil physical and chemical properties, Atterberg limits and consistency indices in hilly region of western Iran. Three land uses including dryland farming, irrigated farming and pasture and four slope positions(i.e., shoulder, backslope, footslope, and toeslope) were used for soil samplings. One hundred eleven soil samples were collected from the surface soil(0-10 cm). Selected physical and chemical properties, liquid limit(LL), plastic limit(PL) and shrinkage limit(SL) were measured using the standard methods; and consistency indices including plastic index(PI), friability index(FI), shrinkage index(SI) and soil activity(A=PI/clay) were calculated. The results showed that irrigated farming significantly increased organic matter content(OM) and OM/clay ratio, and decreased bulk density(ρb) and relative bulk density(ρb-rel) as a result of higher biomass production and plant residues added to the soil compared to other land uses. Except for sand content, OM, ρb, cation exchange capacity(CEC) and calcium carbonate equivalent(CCE), slope position significantly affected soil physical and chemical properties. The highest values of silt, OM/clay and CEC/clay were found in the toeslope position, predominantly induced by soil redistribution within the landscape. The use of complexed(COC)- noncomplexed organic carbon(NCOC) concept indicated that majority of the studied soils were located below the saturation line and the OM in the soils was mainly in the COC form. The LL, PI, FI and A showed significant differences among the land uses; the highest values belonged to the irrigated farming due to high biomass production and plant residues returned to the soils. Furthermore, slope position significantly affected the Atterberg limits and consistency indices except for SL. The highest values of LL, PI, SI and A were observed in the toeslope position probably because of higher OM and CEC/clay due to greater amount of expandable phyllosilicate clays. Overall, soils on the toeslope under irrigated farming with high LL and SI and low values of FI need careful tillage management to avoid soil compaction.

A cluster positioning architecture and relative positioning algorithm based on pigeon fock bionics

Unmanned clusters can realize collaborative work,fexible confguration,and efcient operation,which has become an important development trend of unmanned platforms.Cluster positioning is important for ensuring the normal operation of unmanned clusters.The existing solutions have some problems such as requiring external system assistance,high system complexity,poor architecture scalability,and accumulation of positioning errors over time.Without the aid of the information outside the cluster,we plan to construct the relative position relationship with north alignment to adopt formation control and achieve robust cluster relative positioning.Based on the idea of bionics,this paper proposes a cluster robust hierarchical positioning architecture by analyzing the autonomous behavior of pigeon focks.We divide the clusters into follower clusters,core clusters,and leader nodes,which can realize fexible networking and cluster expansion.Aiming at the core cluster that is the most critical to relative positioning in the architecture,we propose a cluster relative positioning algorithm based on spatiotemporal correlation information.With the design idea of low cost and large-scale application,the algorithm uses intra-cluster ranging and the inertial navigation motion vector to construct the positioning equation and solves it through the Multidimensional Scaling(MDS)and Multiple Objective Particle Swarm Optimization(MOPSO)algorithms.The cluster formation is abstracted as a mixed direction-distance graph and the graph rigidity theory is used to analyze localizability conditions of the algorithm.We designed the cluster positioning simulation software and conducted localizability tests and positioning accuracy tests in diferent scenarios.Compared with the relative positioning algorithm based on Extended Kalman Filter(EKF),the algorithm proposed in this paper has more relaxed positioning conditions and can adapt to a variety of scenarios.It also has higher relative positioning accuracy,and the error does not accumulate over time.

Coseismic gravity and displacement changes of Japan Tohoku earthquake(Mw 9.0)

The greatest earthquake in the modern history of Japan and probably the fourth greatest in the last 100 years in the world occurred on March 11, 2011 off the Pacific coast of Tohoku.Large tsunami and ground motions caused severe damage in wide areas, particularly many towns along the Pacific coast. So far, gravity change caused by such a great earthquake has been reported for the 1964 Alaska and the 2010 Maule events. However, the spatial-temporal resolution of the gravity data for these cases is insufficient to depict a co-seismic gravity field variation in a spatial scale of a plate subduction zone. Here, we report an unequivocal co-seismic gravity change over the Japanese Island, obtained from a hybrid gravity observation（combined absolute and relative gravity measurements）. The time interval of the observation before and after the earthquake is within 1 year at almost all the observed sites, including 13 absolute and 16 relative measurement sites, which deduced tectonic and environmental contributions to the gravity change. The observed gravity agrees well with the result calculated by a dislocation theory based on a self-gravitating and layered spherical earth model. In this computation, a co-seismic slip distribution is determined by an inversion of Global Positioning System（GPS） data. Of particular interest is that the observed gravity change in some area is negative where a remarkable subsidence is observed by GPS, which can not be explained by simple vertical movement of the crust. This indicated that the mass redistribution in the underground affects the gravity change. This result supports the result that Gravity Recovery and Climate Experiment（GRACE） satellites detected a crustal dilatation due to the 2004 Sumatra earthquake by the terrestrial observation with a higher spatial and temporal resolution.

Method to determine α in rough set model based on connection degree

An improvement of tolerance relation is proposed in regard to rough set model based on connection degree by which reflexivity of relation can be assured without loss of information. Then, a method to determine optimal identity degree based on relative positive region is proposed so that the identity degree can be computed in an objective method without any preliminary or additional information about data, which is consistent with the notion of objectivity in rough set theory and data mining theory. Subsequently, an algorithm is proposed, and in two examples, the global optimum identity degree is found out. Finally, in regard to optimum connection degree, the method of rules extraction for connection degree rough set model based on generalization function is presented by which the rules extracted from a decision table are enumerated.

Relative Position and Attitude Control for Drag-Free Satellite with Prescribed Performance and Actuator Saturation

An adaptive prescribed performance control scheme is proposed for the drag free satellite in the presence of actuator saturation and external disturbances.The relative translation and rotation dynamics between the test mass and outer satellite are firstly derived.To guarantee prescribed performance bounds on the transient and steady control errors of relative states,a performance constrained control law is formulated with an error transformed function.In addition,the requirements to know the system parameters and the upper bound of the external disturbance in advance have been eliminated by adaptive updating technique.A command filter is concurrently used to overcome the problem of explosion of complexity inherent in the backstepping control design.Subsequently,a novel auxiliary system is constructed to compensate the adverse effects of the actuator saturation constrains.It is proved that all signals in the closed?loop system are ultimately bounded and prescribed performance of relative position and attitude control errors are guaranteed.Finally,numerical simulation results are given to demonstrate the effectiveness of the proposed approach.

Gly-LysPred: Identification of Lysine Glycation Sites in Protein Using Position Relative Features and Statistical Moments via Chou’s 5 Step Rule

Glycation is a non-enzymatic post-translational modification which assigns sugar molecule and residues to a peptide.It is a clinically important attribute to numerous age-related,metabolic,and chronic diseases such as diabetes,Alzheimer’s,renal failure,etc.Identification of a non-enzymatic reaction are quite challenging in research.Manual identification in labs is a very costly and timeconsuming process.In this research,we developed an accurate,valid,and a robust model named as Gly-LysPred to differentiate the glycated sites from non-glycated sites.Comprehensive techniques using position relative features are used for feature extraction.An algorithm named as a random forest with some preprocessing techniques and feature engineering techniques was developed to train a computational model.Various types of testing techniques such as self-consistency testing,jackknife testing,and cross-validation testing are used to evaluate the model.The overall model’s accuracy was accomplished through self-consistency,jackknife,and cross-validation testing 100%,99.92%,and 99.88%with MCC 1.00,0.99,and 0.997 respectively.In this regard,a user-friendly webserver is also urbanized to accumulate the whole procedure.These features vectorization methods suggest that they can play a critical role in other web servers which are developed to classify lysine glycation.