Study on the removal of NO_x from simulated flue gas using acidic NaClO_2 solution

The study on the removal of NOx from simulated flue gas has been carded out in a lab-scale bubbling reactor using acidic solutions of sodium chlorite. Experiments were performed at various pH values and inlet NO concentrations in the absence or presence of SO2 gas at 45℃. The effect of SO2 on NO oxidation and NO2 absorption was critically examined. The oxidative ability of sodium chlorite was investigated at different pH values and it was found to be a better oxidant at a pH less than 4. In acidic medium, sodium chlorite decomposed into C102 gas, which is believed to participate in NO oxidation as well as in NO2 absorption. A plausible NOx removal mechanism using acidic sodium chlorite solution has been postulated. A maximum NOx removal efficiency of about 81% has been achieved.

Simultaneous removal of NO and SO_2 from dry gas stream using non-thermal plasma

In order to investigate the feasibility of sequential removal NO and SO2 using non-thermal plasma and adsorbent simultaneously, the removal of NO and SO2 from dry gas stream （NO/SO2/N2/O2） with very little O2 using non-thermal plasma was investigated using a coaxial dielectric barrier discharge. Comparative experiments were carried out in the dry gas stream with and without Ar respectively at O2 concentration of 0.1%. The results showed that NO could be removed remarkably and it would be enhanced in the presence of Ar in the dry gas stream. It seems that SO2 could not be removed unless there is Ar in the dry gas stream. The mechanism of removal of NO and SO2 in the dry gas stream was discussed.

Simultaneous catalytic removal of NOx and diesel PM over La_(0.9) K_(0.1) CoO_3 catalyst assisted by plasma

The simultaneous removal of NOx and particulate matter(PM) from diesel exhaust is investigated over a mixed metal oxide catalyst of La 0.9 K 0.1 CoO 3 loaded on γ-Al 2O 3 spherules with the assistant of plasma. It was found that NOx was reduced by PM in oxygen rich atmosphere, the CO 2 and N 2 were produced in the same temperature window without considering the N 2 formed by plasma decomposition. As a result, the temperature for the PM combustion decreases and the reduction efficiency of NOx to N 2 increases during the plasma process, which indicated that the activity of the catalyst can be improved by plasma. The NOx is decomposed by plasma at both low temperature and high temperature. Therefore, the whole efficiency of NOx conversion is enhanced.

Efficient removal of U(VI) from wastewater by a sponge-like 3D porous architecture with hybrid electrospun nanofibers

Removal of uranium(VI)from nuclear wastewater is urgent due to the global nuclear energy exploitation.This study synthesized novel sponge-like 3D porous materials for enhanced uranium adsorption by combining electrospinning and fibrous freeze-shaping techniques.The materials possessed an organic-inorganic hybrid architecture based on the electrospun fibers of polyacrylonitrile(PAN)and SiO_(2).As a sup-porting material,the surface of fibrous SiO_(2) could be further functionalized by cyano groups via(3-cyanopropyl)triethoxysilane.All the cyano groups were turned into amidoxime(AO)groups to obtain a amidoxime-functionalized sponge(PAO/SiO_(2)-AO)through the subsequent ami-doximation process.The proposed sponge exhibited enhanced uranium adsorption performance with a high removal capacity of 367.12 mg/g,a large adsorption coefficient of 4.0×10^(4)mL/g,and a high removal efficiency of 97.59%.The UO_(2)^(2+)adsorption kinetics perfectly conformed to the pseudo-second-order reaction.The sorbent also exhibited an excellent selectivity for UO_(2)^(2+) with other interfering metal ions.2023 Hohai University.Production and hosting by Elsevier B.V.

Efficient and selective removal of Pb(Ⅱ) from landfill leachate using L-serine-modified polyethylene/polypropylene nonwoven fabric synthesized via radiation grafting technique

In this study,to efficiently remove Pb(Ⅱ) from aqueous environments,a novel L-serine-modified polyethylene/polypropylene nonwoven fabric sorbent(NWF-serine)was fabricated through the radiation grafting of glycidyl methacrylate and subsequent L-serine modification.The effect of the absorbed dose was investigated in the range of 5–50 kGy.NWF-serine was characterized by Fourier transform infrared spectroscopy,thermogravimetric analysis,and scanning electron microscopy.Batch adsorption tests were conducted to investigate the influences of pH,adsorption time,temperature,initial concentration,and sorbent dosage on the Pb(Ⅱ) adsorption performance of NWF-serine.The results indicated that Pb(Ⅱ) adsorption onto NWF-serine was an endothermic process,following the pseudo-second-order kinetic model and Langmuir isotherm model.The saturated adsorption capacity was 198.1 mg/g.NWF-serine exhibited Pb(Ⅱ) removal rates of 99.8% for aqueous solutions with initial concentrations of 100 mg/L and 82.1% for landfill leachate containing competitive metal ions such as Cd,Cu,Ni,Mn,and Zn.Furthermore,NWF-serine maintained 86% of its Pb(Ⅱ) uptake after five use cycles.The coordination of the carboxyl and amino groups with Pb(Ⅱ) was confirmed using X-ray photoelectron spectroscopy and extended X-ray absorption fine structure analysis.

Filtration performance and modeling of granular bed for dust removal from coal pyrolytic vapors

Dust removal from pyrolytic vapors at high temperatures is an obstacle to the industrialization of the coal pyrolysis process.In this work,a granular bed with expanded perlites as filtration media was designed and integrated into a 10 t·d^(–1)coal pyrolysis facility.The testing results showed that around 97.56%dust collection efficiency was achieved.As a result,dust content in tar was significantly lowered.The pressure drop of the granular bed maintained in the range of 356 Pa to 489 Pa.The dust size in the effluent after filtration exhibited a bimodal distribution,which was attributed to the heterogeneity of the dust components.The effects of filtration bed on pyrolytic product yields were also discussed.A modified filtration model based on the macroscopic phenomenological theory was proposed to describe the performance of the granular bed.The computation results were well agreed with the experimental data.

Effects of thinning and understory removal on water use efficiency of Pinus massoniana:evidence from photosynthetic capacity and stable carbon isotope analyses

Understanding the relationship between forest management and water use efficiency(WUE)is important for evaluating forest adaptability to climate change.However,the effects of thinning and understory removal on WUE and its key controlling processes are not well understood,which limits our comprehension of the physiological mechanisms of various management practices.In this study,four forest management measures(no thinning:NT;understory removal:UR;light thinning:LT;and heavy thinning:HT)were carried out in Pinus massoniana plantations in a subtropical region of China.Photosynthetic capacity and needle stable carbon isotope composition(δ^(13)C)were measured to assess instantaneous water use efficiency(WUE_(inst))and long-term water use efficiency(WUE_(i)).Multiple regression models and structural equation modelling(SEM)identified the effects of soil properties and physiological performances on WUE_(inst)and WUE_(i).The results show that WUE_(inst)values among the four treatments were insignificant.However,compared with the NT stand(35.8μmol·mol^(-1)),WUE_(i)values significantly increased to 41.7μmol·mol^(-1)in the UR,50.1μmol·mol^(-1)in the LT and 46.6μmol·mol^(-1)in HT treatments,largely explained by photosynthetic capacity and soil water content.Understory removal did not change physiological performance(needle water potential and photosynthetic capacity).Thinning increased the net photosynthetic rate(A_n)but not stomatal conductance(g_s)or predawn needle water potential(ψ_(pd)),implying that the improvement in water use efficiency for thinned stands was largely driven by radiation interception than by soil water availability.In general,thinning may be an appropriate management measure to promote P.massoniana WUE to cope with seasonal droughts under future extreme climates.

Burden of routine orthopedic implant removal a single center retrospective study

BACKGROUND Open reduction and internal fixation represent prevalent orthopedic procedures,sparking ongoing discourse over whether to retain or remove asymptomatic implants.Achieving consensus on this matter is paramount for orthopedic surgeons.This study aims to quantify the impact of routine implant removal on patients and healthcare facilities.A retrospective analysis of implant removal cases from 2016 to 2022 at King Fahad Hospital of the University(KFHU)was conducted and subjected to statistical scrutiny.Among these cases,44%necessitated hospitalization exceeding one day,while 56%required only a single day.Adults exhibited a 55%need for extended hospital stays,contrasting with 22.8%among the pediatric cohort.The complication rate was 6%,with all patients experiencing at least one complication.Notably,34.1%required sick leave and 4.8%exceeded 14 d.General anesthesia was predominant(88%).Routine implant removal introduces unwarranted complications,particularly in adults,potentially prolonging hospitalization.This procedure strains hospital resources,tying up the operating room that could otherwise accommodate critical surgeries.Clearly defined institutional guidelines are imperative to regulate this practice.AIM To measure the burden of routine implant removal on the patients and hospital.METHODS This is a retrospective analysis study of 167 routine implant removal cases treated at KFHU,a tertiary hospital in Saudi Arabia.Data were collected in the orthopedic department at KFHU from February 2016 to August 2022,which includes routine asymptomatic implant removal cases across all age categories.Nonroutine indications such as infection,pain,implant failure,malunion,nonunion,restricted range of motion,and prominent hardware were excluded.Patients who had external fixators removed or joints replaced were also excluded.RESULTS Between February 2016 and August 2022,360 implants were retrieved;however,only 167 of those who met the inclusion criteria were included in this study.The remaining implants were rejected due to exclusion criteria.Among the cases,44%required more than one day in the hospital,whereas 56%required only one day.55%of adults required more than one day of hospitalization,while 22.8%of pediatric patients required more than one day of inpatient care.The complication rate was 6%,with each patient experiencing at least one complication.Sick leave was required in 34.1%of cases,with 4.8%requiring more than 14 d.The most common type of anesthesia used in the surgeries was general anesthesia(88%),and the mean(SD)surgery duration was 77.1(54.7)min.CONCLUSION Routine implant removal causes unnecessary complications,prolongs hospital stays,depletes resources and monopolizing operating rooms that could serve more critical procedures.

Long-term outcomes after endoscopic removal of malignant colorectal polyps:Results from a 10-year cohort

BACKGROUND Choosing an optimal post-polypectomy management strategy of malignant colorectal polyps is challenging,and evidence regarding a surveillance-only strategy is limited.AIM To evaluate long-term outcomes after endoscopic removal of malignant colorectal polyps.METHODS A single-center retrospective cohort study was conducted to evaluate outcomes after endoscopic removal of malignant colorectal polyps between 2010 and 2020.Residual disease rate and nodal metastases after secondary surgery and local and distant recurrence rate for those with at least 1 year of follow-up were invest-igated.Event rates for categorical variables and means for continuous variables with 95%confidence intervals were calculated,and Fisher’s exact test and Mann-Whitney test were performed.Potential risk factors of adverse outcomes were RESULTS In total,135 lesions(mean size:22.1 mm;location:42%rectal)from 129 patients(mean age:67.7 years;56%male)were enrolled.The proportion of pedunculated and non-pedunculated lesions was similar,with en bloc resection in 82%and 47%of lesions,respectively.Tumor differentiation,distance from resection margins,depth of submucosal invasion,lymphovascular invasion,and budding were reported at 89.6%,45.2%,58.5%,31.9%,and 25.2%,respectively.Residual tumor was found in 10 patients,and nodal metastasis was found in 4 of 41 patients who underwent secondary surgical resection.Univariate analysis identified piecemeal resection as a risk factor for residual malignancy(odds ratio:1.74;P=0.042).At least 1 year of follow-up was available for 117 lesions from 111 patients(mean follow-up period:5.59 years).Overall,54%,30%,30%,11%,and 16%of patients presented at the 1-year,3-year,5-year,7-year,and 9-10-year surveillance examinations.Adverse outcomes occurred in 9.0%(local recurrence and dissemination in 4 patients and 9 patients,respectively),with no difference between patients undergoing secondary surgery and surveillance only.CONCLUSION Reporting of histological features and adherence to surveillance colonoscopy needs improvement.Long-term adverse outcome rates might be higher than previously reported,irrespective of whether secondary surgery was performed.

Introducing oxygen vacancies in TiO_(2) lattice through trivalent iron to enhance the photocatalytic removal of indoor NO

The synthesis of oxygen vacancies(OVs)-modified TiO_(2)under mild conditions is attractive.In this work,OVs were easily introduced in TiO_(2)lattice during the hydrothermal doping process of trivalent iron ions.Theoretical calculations based on a novel charge-compensation structure model were employed with experimental methods to reveal the intrinsic photocatalytic mechanism of Fe-doped TiO_(2)(Fe-TiO_(2)).The OVs formation energy in Fe-TiO_(2)(1.12 eV)was only 23.6%of that in TiO_(2)(4.74 eV),explaining why Fe^(3+)doping could introduce OVs in the TiO_(2)lattice.The calculation results also indicated that impurity states introduced by Fe^(3+)and OVs enhanced the light absorption activity of TiO_(2).Additionally,charge carrier transport was investigated through the carrier lifetime and relative mass.The carrier lifetime of Fe-TiO_(2)(4.00,4.10,and 3.34 ns for 1at%,2at%,and 3at%doping contents,respectively)was longer than that of undoped TiO_(2)(3.22 ns),indicating that Fe^(3+) and OVs could promote charge carrier separation,which can be attributed to the larger relative effective mass of electrons and holes.Herein,Fe-TiO_(2)has higher photocatalytic indoor NO removal activity compared with other photocatalysts because it has strong light absorption activity and high carrier separation efficiency.

Material Removal Characteristics of Single-Crystal 4H-SiC Based on Varied-Load Nanoscratch Tests

Single-crystal silicon carbide(SiC)has been widely applied in the military and civil fields because of its excellent physical and chemical properties.However,as is typical in hard-to-machine materials,the good mechanical properties result in surface defects and subsurface damage during precision or ultraprecision machining.In this study,single-and double-varied-load nanoscratch tests were systematically performed on single-crystal 4H-SiC using a nanoindenter system with a Berkovich indenter.The material removal characteristics and cracks under different planes,indenter directions,normal loading rates,and scratch intervals were analyzed using SEM,FIB,and a 3D profilometer,and the mechanisms of material removal and crack propagation were studied.The results showed that the Si-plane of the single-crystal 4H-SiC and edge forward indenter direction are most suitable for material removal and machining.The normal loading rate had little effect on the scratch depth,but a lower loading rate increased the ductile region and critical depth of transition.Additionally,the crack interaction and fluctuation of the depth-distance curves of the second scratch weakened with an increase in the scratch interval,the status of scratches and chips changed,and the comprehensive effects of the propagation and interaction of the three cracks resulted in material fractures and chip accumulation.The calculated and experimental values of the median crack depth also showed good consistency and relativity.Therefore,this study provides an important reference for the high-efficiency and precision machining of single-crystal SiC to ensure high accuracy and a long service life.

Screening of Polyphosphate Accumulating Organisms and Their Phosphorus Removal Performance

[Objectives]To study the phosphorus removal performance of phosphate accumulating organisms(PAOs).[Methods]Activated sludge from domestic sewage treatment plant was used as the strain source,and phosphate accumulating organisms were screened by plate streaking method and dilution coating plate method.Six kinds of excellent phosphate accumulating organisms were obtained by metachromatic granule staining experiment,total phosphorus experiment and simulated sewage phosphorus removal experiment to assist the observation of bac-terial morphology and experiment of phosphorus removal capacity.In addition,the influencing factors of phosphorus removal capacity(nitrogen source,trace metal ions)were analyzed.[Results]In the case of simulated sewage,the phosphorus removal rate of strain b was the highest,reaching 66.25%,while the phosphorus removal rate of strain e and f was about 10%lower than that of the phosphorus uptake experiment.[Conclusions]This study is expected to provide a theoretical reference for the gradual optimization of the screening method of phosphorus re-moval bacteria in domestic sewage treatment.

Removal Effect of Precipitation on Atmospheric Particulate Matter (PM_(2.5) ) in Bengbu City

Based on the monitoring data of PM_(2.5) concentration in Bengbu Environmental Monitoring Station and precipitation observation data of Bengbu National Meteorological Observation Station from 2016 to 2019, the influence of precipitation on PM_(2.5) mass concentration in Bengbu City was analyzed. The results show that precipitation had a washing and removal effect on PM_(2.5) in the air, and the removal effect was related to precipitation level, precipitation intensity, precipitation duration and PM_(2.5) concentration. The removal effect of precipitation on PM_(2.5) increased with the increase of precipitation level, and the seasonal difference was obvious. Precipitation intensity was positively correlated with the removal effect of PM_(2.5) , but the average removal rate began to decline when precipitation intensity exceeded 10 mm. With the increase of precipitation intensity, the proportion of positive removal showed an overall upward trend, but there was a low-value area as precipitation intensity was 3-10 mm. Precipitation duration was also positively correlated with the removal effect of PM_(2.5) , and there was a low-value area when precipitation duration was 10-15 h. When PM_(2.5) concentration was low before the precipitation process began, the removal effect was not good, and the average removal rate was negative. As PM_(2.5) concentration was high before the precipitation process started, the removal effect was obvious.

Comprehensive Analysis of Indoor Formaldehyde Removal Techniques:Exploring Physical,Chemical,and Biological Methods

This research focuses on the evaluation of diverse approaches for removing formaldehyde from indoor environments,which is a significant concern for indoor air quality.The study systematically examines physical,chemical,and biological methods to ascertain their effectiveness in formaldehyde mitigation.Physical methods,including air circulation and adsorption,particularly with activated carbon and molecular sieves,are assessed for their efficiency in various concentration scenarios.Chemical methods,such as photocatalytic oxidation using titanium dioxide and plasma technology,are analyzed for their ability to decompose formaldehyde into non-toxic substances.Additionally,biological methods involving plant purification and microbial transformation are explored for their eco-friendly and sustainable removal capabilities.The paper concludes that while each method has its merits,a combined approach may offer the most effective solution for reducing indoor formaldehyde levels.The study underscores the need for further research to integrate these methods in a practical,cost-effective,and environmentally sustainable manner,highlighting their potential to improve indoor air quality significantly.

Numerical study of the deep removal of R134a from non-condensable gas mixture by cryogenic condensation and de-sublimation

Nowadays,the limits on greenhouse gas emissions are becoming increasingly stringent.In present research,a two-dimensional numerical model was established to simulate the deep removal of 1,1,1,2-tetrafluoroethane(R134a)from the non-condensable gas(NCG)mixture by cryogenic condensation and de-sublimation.The wall condensation method was compiled into the Fluent software to calculate the condensation of R134a from the gas mixture.Besides,the saturated thermodynamic properties of R134a under its triple point were extrapolated by the equation of state.The simulation of the steam condensation with NCG was conducted to verify the validity of the model,the results matched well with the experimental data.Subsequently,the condensation characteristics of R134a with NCG and the thermodynamic parameters affecting condensation were studied.The results show that the section with relatively higher removal efficiency is usually near the inlet.The cold wall temperature has a great influence on the R134a removal performance,e.g.,a 15 K reduction of the wall temperature brings a reduction in the outlet R134a molar fraction by 85.43%.The effect of changing mass flow rate on R134a removal is mainly reflected at the outlet,where an increase in mass flow rate of 12.6% can aggravate the outlet molar fraction to 210.3% of the original.The research can provide a valuable reference for the simulation of the deep removal of various low-concentration gas using condensation and de-sublimation methods.

Controllably partial removal of thiolate ligands from unsupported Au_(25) nanoclusters by rapid thermal treatments for electrochemical CO_(2)reduction

Colloidal synthesis of metal nanoclusters will inevitably lead to the blockage of catalytically active sites by organic ligands.Here,taking[Au_(25)(PET)_(18)]-(PET=2-phenylethanethiol)nanocluster as a model catalyst,this work reports a feasible procedure to achieve the controllably partial removal of thiolate ligands from unsupported[Au_(25)(PET)_(18)]-nanoclusters with the preservation of the core structure.This procedure shortens the processing duration by rapid heating and cooling on the basis of traditional annealing treatment,avoiding the reconfiguration or agglomeration of Au_(25)nanoclusters,where the degree of dethiolation can be regulated by the control of duration.This work finds that a moderate degree of dethiolation can expose the Au active sites while maintaining the suppression of the competing hydrogen evolution reaction.Consequently,the activity and selectivity towards CO formation in electrochemical CO_(2)reduction reaction of Au_(25)nanoclusters can be promoted.This work provides a new approach for the removal of thiolate ligands from atomically precise gold nanoclusters.

Application and Regeneration of a Non-Aqueous System of Cu/HCl and DMF for the Oxidation of Hydrogen Sulfide in Natural Gas

A copper-based non-aqueous-phase desulfurization agent is prepared by adding CuCl_(2) to the solvent N,Ndimethylformamide(DMF).Static desulfurization experiments show that the agent has high efficiency.However,the desulfurization reaction leads to the formation of a copper sulfide precipitate.It is found that the addition of chloride ions in the form of hydrochloric acid or potassium chloride prevents the formation of copper sulfide,and elemental sulfur is precipitated instead.The efficient absorption of H2S by the Cu/HCl–DMF agent relies on the rapid coordination of Cu^(2+)with DMF,Cl^(−),and H2S molecules to form a[Cu(DMF)_(n−p)(HS−)_(p)(Cl−)_(m)]_((2−p−m))+complex.The desulfurization agent has a sulfur capacity of up to 9.81 g/L when used in static bubble desulfurization at atmospheric pressure.The system has low viscosity and good chemical and thermal stability.It can be rapidly regenerated through continuous oxidation.After five repetitions of the regeneration procedure,the sulfur capacity reaches more than 91%of the initial capacity,indicating the potential of the system for commercial applications.

Investigation of paint removal by atmospheric pressure plasma jet

Acrylic polyurethane paint on the surface of 2A12 Al alloy was cleaned utilizing an atmospheric pressure plasma jet in this work.The dynamic evolution of the paint removal process during plasma treatment with time was explored through analysis of morphology and chemical states.The results showed that although the thickness of paint could be reduced effectively with an increase in cleaning time,the removal rate of paint gradually decreased with time.During the initial cleaning process range,its original smooth morphology of paint turned rugged quickly and was almost unchanged with further plasma treatment.Element and chemical state analysis showed that the content of C in the paint layer decreased obviously after plasma treatment.In contrast,the O content increased remarkably.The cleaning mechanism could be mainly attributed to the reaction between active O-containing species in air plasma and organic components in the paint.After removal of superficial organic matter,residue inorganic metal oxide substances aggregated on the base.The exposed metal oxides on the one hand elevated the superficial O content,but on the other hand hindered further plasma penetration,resulting in a gradual decrease in cleaning rate with cleaning time.Therefore,physical wiping was proposed to be incorporated with the plasma method and effective removal of paint was realized.

The Ultrafiltration Process Enhances Antibiotic Removal in the Full-Scale Advanced Treatment of Drinking Water

1.Introduction A considerable proportion(30%–90%)of consumed antibiotics are excreted from organisms after intake,and wastewater treatment facilities lack sufficient capacity to remove antibiotics in water[1].Thus,the issue of antibiotics contamination in drinking water is raising increasing attention.Adverse consequences of antibiotics in drinking water include potential human health risks(e.g.,they may be carcinogenic or provoke allergic reactions)and risks to the aquatic ecology due to the promotion of bacterialresistant genes[2,3].

Characteristics of anoxic phosphors removal in sequence batch reactor

The characteristics of anaerobic phosphorus release and anoxic phosphorus uptake were investigated in sequencing batch reactors using denitrifying phosphorus removing bacteria （DPB） sludge. The lab-scale experiments were accomplished under conditions of various nitrite concentrations （5.5, 9.5, and 15 mg/L） and mixed liquor suspended solids （MLSS） （1844, 3231, and 6730 mg/L）. The results obtained confirmed that nitrite, MLSS, and pH were key factors, which had a significant impact on anaerobic phosphorus release and anoxic phosphorus uptake in the biological phosphorous removal process. The nitrites were able to successfully act as electron acceptors for phosphorous uptake at a limited concentration between 5.5 and 9.5 mg/L. The denitrification and dephosphorous were inhibited when the nitrite concentration reached 15 mg/L. This observation indicated that the nitrite would not inhibit phosphorus uptake before it exceeded a threshold concentration. It was assumed that an increase of MLSS concentration from 1844 mg/L to 6730 mg/L led to the increase of denitrification and anoxic P-uptake rate. On the contrary, the average P-uptake/N denitrifying reduced from 2.10 to 1.57 mg PO4^3--P/mg NO3^--N. Therefore, it could be concluded that increasing MLSS of the DEPHANOX system might shorten the reaction time of phosphorus release and anoxic phosphorus uptake. However, excessive MLSS might reduce the specific denitrifying rate. Meanwhile, a rapid pH increase occurred at the beginning of the anoxic conditions as a result of denitrification and anoxic phosphate uptake. Anaerobic P release rate increased with an increase in pH. Moreover, when pH exceeded a relatively high value of 8.0, the dissolved P concentration decreased in the liquid phase, because of chemical precipitation. This observation suggested that pH should be strictly controlled below 8.0 to avoid chemical precipitation if the biological denitrifying phosphorus removal capability is to be studied accurately.