Residual stress modeling of mitigated fused silica damage sites with CO_(2)laser annealing

A numerical model based on measured fictive temperature distributions is explored to evaluate the residual stress fields of CO_(2)laser-annealed mitigated fused silica damage sites.The proposed model extracts the residual strain from the differences in thermoelastic contraction of fused silica with different fictive temperatures from the initial frozen-in temperatures to ambient temperature.The residual stress fields of mitigated damage sites for the CO_(2)laser-annealed case are obtained by a finite element analysis of equilibrium equations and constitutive equations.The simulated results indicate that the proposed model can accurately evaluate the residual stress fields of laser-annealed mitigated damage sites with a complex thermal history.The calculated maximum hoop stress is in good agreement with the reported experimental result.The estimated optical retardance profiles from the calculated radial and hoop stress fields are consistent with the photoelastic measurements.These results provide sufficient evidence to demonstrate the suitability of the proposed model for describing the residual stresses of mitigated fused silica damage sites after CO_(2)laser annealing.

Additive manufacturing of Ni-based superalloys: Residual stress, mechanisms of crack formation and strategies for crack inhibition

The additive manufacturing(AM)of Ni-based superalloys has attracted extensive interest from both academia and industry due to its unique capabilities to fabricate complex and high-performance components for use in high-end industrial systems.However,the intense temperature gradient induced by the rapid heating and cooling processes of AM can generate high levels of residual stress and metastable chemical and structural states,inevitably leading to severe metallurgical defects in Ni-based superalloys.Cracks are the greatest threat to these materials’integrity as they can rapidly propagate and thereby cause sudden and non-predictable failure.Consequently,there is a need for a deeper understanding of residual stress and cracking mechanisms in additively manufactured Ni-based superalloys and ways to potentially prevent cracking,as this knowledge will enable the wider application of these unique materials.To this end,this paper comprehensively reviews the residual stress and the various mechanisms of crack formation in Ni-based superalloys during AM.In addition,several common methods for inhibiting crack formation are presented to assist the research community to develop methods for the fabrication of crack-free additively manufactured components.

Application of Nonlinear Lamb Wave Mixing Method for Residual Stress Measurement in Metal Plate

Harmonic nonlinear ultrasound can offer high sensitivity for residual stress measurements;however,it cannot be used for local stress measurements at a point in space and exhibits nonlinear distortions in the experimental system.This paper presents a feasibility study on the measurement of residual stress in a metal plate using a nonlinear Lamb wave-mixing technique.The resonant conditions for two Lamb waves to generate a mixing frequency wave are obtained via theoretical analysis.Finite element simulations are performed to investigate the nonlinear interactions between the two Lamb waves.Results show that two incident A0 waves interact in regions of material nonlinearity and generate a rightward S0 wave at the sum frequency.Residual stress measurement experiments are conducted on steel plate specimens using the collinear Lamb wave-mixing technique.By setting different delays for two transmitters,the generated sum-frequency component at different spatial locations is measured.Experimental results show that the spatial distribution of the amplitude of the sum-frequency component agrees well with the spatial distribution of the residual stress measured using X-rays.The proposed collinear Lamb wave-mixing method is effective for measuring the distribution of residual stress in metal plates.

Residual Stresses and Forming Quality of Metal Bipolar Plates for PEMFC During the Stamping Process

Stamping is a critical step in the manufacture of metallic bipolar plates.Typically,residual stress and a spring back effect appear on the bipolar plate after the stamping process,which impacts on the performance and lifetime of the proton exchange membrane fuel cell(PEMFC).The residual stress and spring back behavior which occur as a result of stamping a bipolar plate are investigated in this study.The effects of the punch radius,the die radius,the channel depth,and the clearance between the punch and the die on the residual stress and forming quality of the bipolar plate are examined.The stamping process can be divided into three stages.The high stress area and the middle section residual stress area were selected to study the formation process and to obtain the composition of the residual stress regions.Spring back was mainly related to the position of the fixed end of the sheet and the degree of plastic deformation,and the sheet thickness have increased by 2μm after spring back.Based on the results of finite element analysis,as described by the distribution of residual stress,the formation,the thickness of the middle cross section and the equivalent plastic strain,it was found that all the tool parameters affected the distribution of the residual stress.This research can provide a design reference for the manufacture of metallic bipolar plates based on the stamping process.

Fatigue Life Prediction for SiC/Al Materials Based on Path Planning Algorithm Considering Residual Stress

To explore the influence of path deflection on crack propagation,a path planning algorithm is presented to calculate the crack growth length.The fatigue crack growth life of metal matrix composites(MMCs)is estimated based on an improved Paris formula.Considering the different expansion coefficient of different materials,the unequal shrinkage will lead to residual stress when the composite is molded and cooled.The crack growth model is improved by the modified stress ratio based on residual stress.The Dijkstra algorithm is introduced to avoid the cracks passing through the strengthening base and the characteristics of crack steps.This model can be extended to predict crack growth length for other similarly-structured composite materials.The shortest path of crack growth is simulated by using path planning algorithm,and the fatigue life of composites is calculated based on the shortest path and improved model.And the residual stress caused by temperature change is considered to improve the fatigue crack growth model in the material.The improved model can well predict the fatigue life curve of composites.By analyzing the fatigue life of composites,it is found that there is a certain regularity based on metal materials,and the new fatigue prediction model can also reflect this regularity.

Residual stress measurement and analysis of siliceous slate-containing quartz veins

Engineering geological disasters such as rockburst have always been a critical factor affecting the safety of coal mine production.Thus,residual stress is considered a feasible method to explain these geomechanical phenomena.In this study,electron backscatter diffraction(EBSD)and optical microscopy were used to characterize the rock microcosm.A measuring area that met the requirements of X-ray diffraction(XRD)residual stress measurement was determined to account for the mechanism of rock residual stress.Then,the residual stress of a siliceous slate-containing quartz vein was measured and calculated using the sin^(2) ϕ method equipped with an X-ray diffractometer.Analysis of microscopic test results showed homogeneous areas with small particles within the millimeter range,meeting the requirements of XRD stress measurement statistics.Quartz was determined as the calibration mineral for slate samples containing quartz veins.The diffraction patterns of the(324)crystal plane were obtained under different ϕ and φ.The deviation direction of the diffraction peaks was consistent,indicating that the sample tested had residual stress.In addition,the principal residual stress within the quartz vein measured by XRD was compressive,ranging from 10 to 33 MPa.The maximum principal stress was parallel to the vein trend,whereas the minimum principal stress was perpendicular to the vein trend.Furthermore,the content of the low-angle boundary and twin boundary in the quartz veins was relatively high,which enhances the resistance of the rock mass to deformation and promotes the easy formation of strain concentrations,thereby resulting in residual stress.The proposed method for measuring residual stress can serve as a reference for subsequent observation and related research on residual stress in different types of rocks.

Residual stress with asymmetric spray quenching for thick aluminum alloy plates

Solution and quenching heat treatments are generally carried out in a roller hearth furnace for large-scale thick aluminum alloy plates.However,the asymmetric or uneven spray water flow rate is inevitable under industrial production conditions,which leads to an asymmetric residual stress distribution.The spray quenching treatment was conducted on self-designed spray equipment,and the residual stress along the thickness direction was measured by a layer removal method based on deflections.Under the asymmetric spray quenching condition,the subsurface stress of the high-flow rate surface was lower than that of the low-flow rate surface,and the difference between the two subsurface stresses increased with the increase in the difference in water flow rates.The subsurface stress underneath the surface with a water flow rate of 0.60 m^(3)/h was 15.38 MPa less than that of 0.15 m^(3)/h.The simulated residual stress by finite element(FE)method of the high heat transfer coefficient(HTC)surface was less than that of the low HTC surface,which is consistent with the experimental results.The FE model can be used to analyze the strain and stress evolution and predict the quenched stress magnitude and distribution.

Residual Stress Distribution of Si_(3)N_(4)/SiC Gradient Material and the Effect of Residual Stress on Material Properties

The Si_(3)N_(4)/SiC gradient material with a gradient composition structure was prepared by a hot pressing sintering.The sinterability,distribution of residual stress and the effect of residual stress on mechanical properties of Si_(3)N_(4)/SiC gradient materials were studied.The research results show that,at 1750℃,Si_(3)N_(4)/SiC gradient materials with different ratios can achieve co-sintering,and the overall relative density of the sample reaches 98.5%.Interestingly,the flexural strength of Si_(3)N_(4)/SiC gradient material is related to its loading surface.The flexural strength of SiC as the loading surface is about 35%higher than that of Si_(3)N_(4)as the loading surface.The analysis of the residual stress of the material in the gradient structure shows that the gradient stress distribution between the two phases is a vital factor affecting the mechanical properties of the material.With the increase of SiC content in the gradient direction,the fracture toughness of each layer of Si_(3)N_(4)/SiC gradient materials gradually decreases.The surface hardness of the pure SiC side is lower than that reported in other literature.

Study of residual stresses and distortions from the Ti6Al4V based thinwalled geometries built using LPBF process

The current paper focuses on the prediction of residual stresses and distortions in the Laser Powder Bed Fusion(LPBF)built Ti6Al4V thin-walled geometries using Ansys Additive Print(AAP)software which employs a layer-by-layer accumulation of inherent strain to calculate the deformations.Isotropic and anisotropic strain scaling factors were calibrated initially within the APP software for the Ti6Al4V based single cantilever beam geometry.Subsequently,the numerical simulations were performed in APP software and computed the residual stresses and distortions for the varied process parameters including laser power,scan speed and hatch distance while maintaining the layer thickness constant for all the design iterations.The numerical predictions were compared;they were found to match reasonably well with the XRD measurements within the calibrated regime.

Mechanism investigation and strategies for reducing residual stress at open ends of the roll-formed part

Increasing geometrical accuracy at open ends of the roll-formed part is difficult due to the release of residual stress after end cutting.In this work,a typical rail with a high requirement of geometry accuracy was selected to realize the behaviors of residual stress release.First,residual stress distribution after roll forming is discussed in detail by finite element analysis with ABAQUS.In addition,two different approaches are proposed to check their capabilities in reducing the residual stress level.The results indicate that both additional rolling passes and multiple bending processes are beneficial to reducing uniform residual stress.

A Way to Determine the Maximum Inducible Residual Stresses in Steel by Mechanical Surface Treatment

The issue of determining the maximum compressive residual stress that can be induced through mechanical surface treatment is of great significance.There are two possible approaches,namely stress peening and stress rolling,both to determine the limit.Steel with high hardness may be under the yield strength,while for those with lower tensile strength,the hardness is increased,and the limit is above the tensile strength.

Literature Review of Electronic Packaging Technology and Residual Stress

The rapid development of the electronic information industry brings to the irreplaceable role of electronic components, therefore the search of a more reliable packaging material has become increasingly important. In the electronic packaging system, the failure phenomenon caused by residual stress is one of the key factors restricting the development of electronic packaging technology. In order to use the in-situ characterization technology to explore the residual stress inducing mechanism and failure mechanism of epoxy-based advanced packaging materials, this paper gives a review of related previous research, and lays a theoretical foundation for the upcoming research. The classification and generation mechanism of residual stress are clarified in this paper, which provides data support for future related research.

Residual Stress and Fracture Toughness Study in A516 Gr70 Steel Joints Welded and Repaired by Arc Processes

Structural components made of steel are used in several areas and require welding for assembly. In some situations, repair of the weld bead, also performed by electric arc welding, can be used to correct, and eliminate any discontinuities. However, electric arc welding causes the presence of residual stresses in the joint, which can impair its performance and not meet specific design requirements. In this paper, welded joints made of ASTM A 516 GR 70 steel plates, with a thickness of 30.5 mm, welded by the MAG—Metal Active Gas process (20% CO2) and using a “K” groove were analysed. The joints were manufactured with seven welding passes on each side of the groove. After welding, one batch underwent repair of the bead by TIG welding (Tungsten Insert Gas) and another batch underwent two repairs by TIG welding. Were presented results of the behaviour of the residual stress profile measured by X-ray diffraction and the Vickers microhardness profile in the joints as well the fracture toughness in the conditions only welded and submitted to repairs. The results indicated that the greater number of repair passes reduced the residual compressive stress values obtained in the material manufacturing process and caused a stabilization on the Vickers hardness values. It was concluded that compressive residual stresses did not play a major role in the R-curve results. The presence of discontinuities in the welded joint caused greater influence on the behaviour of the R curve.

Numerical simulation of residual stress field in green power metallurgy compacts by modified Drucker-Prager Cap model

基于修正的Drucker-Prager Cap模型建立弹塑性本构模型,采用三维有限元模型对粉末压制过程及压制脱模后压坯的残余应力进行仿真分析。利用几个典型的力学性能测试实验确定粉末Distaloy AE的模型参数。模型通过用户子程序USDFLD实现,对粉末Distaloy AE的模压过程及脱模后压坯(d20 mm×5 mm)的残余应力进行预测分析。有限元分析结果与模压实验和X衍射实验结果基本吻合,验证了模型的有效性。结果表明,压坯的侧表面存在一层显著的残余压应力,而压坯上表面和下表面的残余应力值则很小。

Numerical Calculation and Experimental Research on Residual Stresses in Precipitation-hardening Layer of NAK80 Steel for Shot Peening

Shot peening can improve fatigue strength of materials by creating compressive residual stress field in their surface layers,and offers a protection against crack initiation and propagation,corrosion,etc.And fatigue fracture and stress corrosion cracking of NAK80 steel parts are improved effectively.Currently there lacks in-depth research in which the beneficial effect of the residual stress may be offset by the surface damage associated with shot peening,especially in terms of the research on the effective control of shot peening intensity.In order to obtain the surface residual stress field of NAK80 steel after shot peening,the samples are shot peened by pneumatic shot peening machine with different rules.The residual stress in the precipitation-hardening layer of NAK80 steel is measured before and after a shot peening treatment by X-ray diffraction method.In order to obtain true residual stress field,integral compensation method is used to correct results.By setting up analytical model of the residual stress in the process of shot peening,the surface residual stress is calculated after shot peening,and mentioning the reason of errors occurred between calculated and experimental residual stresses,which is mainly caused by the measurement error of the shoot arc height.At the same time,micro hardness,microstructure and roughness in the precipitation-hardening layer of NAK80 steel before and after shot peening were measured and surveyed in order to obtain the relation between shot peening strength and surface quality in the precipitation-hardening layer.The results show that the surface quality of NAK80 steel is significantly improved by shot peening process.The over peening effect is produced when the shot peening intensity is too high,it is disadvantageous to improve sample＇s surface integrity,and leading to reduce the fatigue life.When arc high value of optimal shot peening is 0.40 mm,the surface quality is the best,and the depth of residual stress in the precipitation-hardening layer reaches to about 450 μm.Numerical calculation is very useful to define the process parameters when a specific residual stress profile is intended,either to quantify the benefits on a specific property like fatigue life or to help on modeling a forming process like shot peen forming.In particular,the proposed parameter optimization in the progress of shot peening and effective control of the surface texture provide new rules for the quantitative evaluations of shot peening surface modification of NAK80 steel.

Study of residual stresses in tailor rolled blanked Al5J32-T4 sheets

Several automotive parts such as door panels have been manufactured by using load-adapted blanks for crash optimization and weight minimization. Recently, Tailor Rolled Blanks (TRB) has been introduced to remove the disadvantages of a welding process which was used in joining panel components. TRB offers better structural design capabilities due to the seamless transitions on the panels with different thicknesses. In spite of the advantages of the process, TRB leaves internal stresses in the panel. This residual stresses lower the formability of Tailor Rolled Blanked (TRBed) parts and cause cracks near severe curvature during subsequent forming processes. In this research, the residual stresses of TRBed Al5J32-T4 sheets were studied by X-ray stress analysis, and also microstructure was observed along the rolling direction. In addition, heat treatment was done after TRB process in order to compare the residual stresses to that of the TRBed sheets before the heat treatment.

Simulation on Residual Stress of Shot Peening Based on a Symmetrical Cell Model

The symmetrical cell model is widely used to study the residual stress induced by shot peening. However, the correlation between the predicted residual stresses and the shot peening coverage, which is a big challenge for the researchers of the symmetrical cell model, is still not established. Based on the dynamic stresses and the residual stresses outputted from the symmetrical cell model, the residual stresses corresponding to full coverage are evalu- ated by normal distribution analysis. The predicted nodal dynamic stresses with respect to four corner points indicate that the equi-biaxial stress state exists only for the first shot impact. Along with the increase of shot number, the interactions of multiple shot impacts make the fluctuation of the nodal dynamic stresses about an almost identical value more and more obvious. The mean values and standard deviations of the residual stresses gradually tend to be stable with the increase of the number of shot peening series. The mean values at each corner point are almost the same after the third peening series, which means that an equi-biaxial stress state corresponding to the full coverage of shot peening is achieved. Therefore, the mean values of the nodal residual stresses with respect to a specific transverse cross-section below the peened surface can be used to correlate the measured data by X-ray. The predicted residual stress profile agrees with the experimental results very well under 200% peening coverage. An effective correlation method is proposed for the nodal residual stresses predicted by the symmetrical cell model and the shot peening coverage.

Measurement of residual stress in a multi-layer semiconductor heterostructure by micro-Raman spectroscopy

Si-based multilayer structures are widely used in current microelectronics. During their preparation, some inhomogeneous residual stress is induced, resulting in competition between interface mismatching and surface energy and even leading to structure failure. This work presents a methodological study on the measurement of residual stress in a multi-layer semiconductor heterostructure. Scanning electron microscopy（SEM）, micro-Raman spectroscopy（MRS）, and transmission electron microscopy（TEM） were applied to measure the geometric parameters of the multilayer structure. The relationship between the Raman spectrum and the stress/strain on the [100] and [110] crystal orientations was determined to enable surface and crosssection residual stress analyses, respectively. Based on the Raman mapping results, the distribution of residual stress along the depth of the multi-layer heterostructure was successfully obtained.

Effects of austempering temperature on microstructure and surface residual stress of carbidic austempered ductile iron(CADI) grinding balls

The effects of austempering temperature on microstructure and surface residual stress of carbidic austempered ductile iron(CADI) grinding balls were systematically investigated in this work. The microstructures were oberserved by optical metallography and analyized by X-ray diffraction. The surface residual stress measured by the cutting method is mainly composed of thermal stress and phase transformation stress. The thermal stress in grinding balls was determined by ANSYS simulation technique, and the surface phase transformation stress was obtained by subtracting the simulated surface thermal stress from the measured surface residual stress. Results show that all microstructures consist of ausferrite, white-bright zones(mixture of martensite and austenite), nodular graphite, and carbides. The distribution of ausferrite shows uniform. With the increase of austempering temperature, the volume fraction and carbon content of austenite increase, whereas the amount of white-bright zone decreases. In addition, the surface residual stress increases with the increase of austempering temperature. Only the tension exists at the austempering temperature of 200 ℃, and the pressure exists at the austempering temperature of 220-260 ℃. The thermal stress changes from the tension on the inside with the radius of 0-35 mm to the pressure on the outside with the radius of 35-62.5 mm, and the stress balance state presents at the radius of 35 mm. It is also found that the transformation stress is related to the content of carbon-rich austenite, and will reduce by 5.03 MPa accompanied with 1 vol.% increase of the austenite. The thermal compressive stress and the transformation tensile stress on the surface both decrease with the increase of the austempering temperature.

FEM SIMULATION OF RESIDUAL STRESSES INDUCED BY LASER SHOCK WITH OVERLAPPING LASER SPOTS

The finite element method is presented to attain the numerical simulation of the residual stresses field in the material treated by laser shock processing. The distribution of residual stresses generated by a single laser shock with square and round laser spot is predicted and validated by experimental results. With the Finite Element Method （FEM） model, effects of different overlapping rates and impact sequences on the distribution of residual stresses are simulated. The results indicate that： （1） Overlapping laser shock can increase the compressive residual stresses. However, it is not effective on the growth of plastically affected depth; （2） Overlapping rate should be optimized and selected carefully for the large area treatment. Appropriate overlapping rate is beneficial to obtain a homogeneous residual stress field; （3） The impact sequence has a great effect on the residual stress field. It can greatly attenuate the phenomenon of the “residual stress hole” to obtain a homogeneous residual stress field.