A Boron-based Adhesion Aid for Efficient Bonding of Silicone Rubber and Epoxy Resin

We improved the adhesion between silicon based insulating materials and epoxy resin composites by adding the adhesion promoter cycloborosiloxane(BSi,cyclo-1,3,3,5,7,7-hexaphenyl-1,5-diboro-3,7-disiloxane).The experimental results show that the addition of BSi in the silicone rubber(SR)system significantly increases the tensile shear strength between BSi and epoxy resin(EP),reaching 309%of the original value.On this basis,the mechanism of BSi to enhance the adhesion effect was discussed.The electron deficient B in BSi attracted the electron rich N and O in EP to enhance the chemical interaction,combined with the interfacial migration behavior in the curing process,to improve the adhesion strength.This study provides the design and synthesis ideas of adhesive aids,and a reference for further exploring the interface mechanism of epoxy resin matrix composites.

Influence of Non-smooth Surface on Tribological Properties of Glass Fiber-epoxy Resin Composite Sliding against Stainless Steel under Natural Seawater Lubrication

With the development of bionics, the bionic non-smooth surfaces are introduced to the field of tribology. Although non-smooth surface has been studied widely, the studies of non-smooth surface under the natural seawater lubrication are still very fewer, especially experimental research. The influences of smooth and non-smooth surface on the frictional properties of the glass fiber-epoxy resin composite（GF/EPR） coupled with stainless steel 316 L are investigated under natural seawater lubrication in this paper. The tested non-smooth surfaces include the surfaces with semi-spherical pits, the conical pits, the cone-cylinder combined pits, the cylindrical pits and through holes. The friction and wear tests are performed using a ring-on-disc test rig under 60 N load and 1000 r/min rotational speed. The tests results show that GF/EPR with bionic non-smooth surface has quite lower friction coefficient and better wear resistance than GF/EPR with smooth surface without pits. The average friction coefficient of GF/EPR with semi-spherical pits is 0.088, which shows the largest reduction is approximately 63.18% of GF/EPR with smooth surface. In addition, the wear debris on the worn surfaces of GF/EPR are observed by a confocal scanning laser microscope. It is shown that the primary wear mechanism is the abrasive wear. The research results provide some design parameters for non-smooth surface, and the experiment results can serve as a beneficial supplement to non-smooth surface study.

Experimental Study on Influence of Dimples on Lubrication Performance of Glass Fiber-epoxy Resin Composite under Natural Seawater Lubrication

Bionic non-smooth surface is widely applied in metal and ceramics materials. In order to introduce this technology to high pressure seawater pump, the influence of bionic non-smooth surface on the engineering plastics used in pump should be investigated. The comparative tests are carried out with a ring-on-disc configuration under 800, 1000, 1200 and 1400 r/min in order to research the influence of the bionic non-smooth surface on glass fiber-epoxy resin composite（GF/EPR） under natural seawater lubrication. The disc surfaces are textured with five kinds of pits, which are semi-spherical, conical, cone-cylinder combined, cylindrical pits and through holes, respectively. A smooth surface is tested as reference. The results show that the lubrication performance of dimpled GF/EPR sample is much better than that of the smooth sample under all rotational speeds. The semi-spherical pits surface has more obvious friction reduction than the others, which shows that the least reduction is approximately 43.29% of smooth surface under 1200 r/rain. However, the wear level is only marginally influenced by dimples. The surface morphology investigations disclose severe modifications caused by abrasive wear primarily. The results are helpful to vary friction properties of GF/EPR by non-smooth surface, or provide references to the design of non-smooth surfaces under certain condition.

Determination of Water Diffusion Coefficients and Dynamics in Adhesive/Carbon Fiber Reinforced Epoxy Resin Composite Joints

To determinate the water diffusion coefficients and dynamics in adhesive/carben fiber reinforced epoxy resin composite joints, energy dispersive X-ray spectroscopy analysis（EDX） is used to establish the content change of oxy- gen in the adhesive in adhesive/carbon fther reinforced epoxy resin composite joints. As water is made up of oxygen and hydrogen, the water diffusion coefficients and dynamics in adhesive/carben fiber reinforced epoxy resin composite joints can be obtained from the change in the content of oxygen in the adhesive during humidity aging, via EDX analy-sis. The authors have calculated the water diffusion coefficients and dynamics in the adhesive/carbon fiber reinforced epoxy resin composite joints with the aid of beth energy dispersive X-ray spectroscopy and elemental analysis. The de- termined results with EDX analysis are almost the same as those determined with elemental analysis and the results al- so show that the durability of the adhesive/carbon fther reinforced epoxy resin composite joints subjected to silane cou- pling agent treatment is better than those subjected to sand paper burnishing treatment and chemical oxidation treat- ment.

Research on properties of hollow glass microspheres/epoxy resin composites applied in deep rock in-situ temperature-preserved coring

Deep petroleum resources are in a high-temperature environment.However,the traditional deep rock coring method has no temperature preserved measures and ignores the effect of temperature on rock porosity and permeability,which will lead to the distortion of the petroleum resources reserves assessment.Therefore,the hollow glass microspheres/epoxy resin(HGM/EP)composites were innovatively proposed as temperature preserved materials for in-situ temperature-preserved coring(ITP-Coring),and the physical,mechanical,and temperature preserved properties were evaluated.The results indicated that:As the HGM content increased,the density and mechanical properties of the composites gradually decreased,while the water absorption was deficient without hydrostatic pressure.For composites with 50 vol%HGM,when the hydrostatic pressure reached 60 MPa,the water absorption was above 30.19%,and the physical and mechanical properties of composites were weakened.When the hydrostatic pressure was lower than 40 MPa,the mechanical properties and thermal conductivity of composites were almost unchanged.Therefore,the composites with 50 vol%HGM can be used for ITPCoring operations in deep environments with the highest hydrostatic pressure of 40 MPa.Finally,to further understand the temperature preserved performance of composites in practical applications,the temperature preserved properties were measured.An unsteady-state heat transfer model was established based on the test results,then the theoretical change of the core temperature during the coring process was obtained.The above tests results can provide a research basis for deep rock in-situ temperature preserved corer and support accurate assessment of deep petroleum reserves.

Epoxy Resin/Nano Ni@C Composites Exhibiting NTC Effect with Tunable Resistivity

Epoxy resin/Ni@C nanoparticle composites with aligned microstructure were prepared by using a procedure of magnetic field assisted curing. The results show that the resistivity of composites exhibits negative temperature coefficient （NTC） effect above room temperature, and can be adjusted by varying the content filler and the magnitude of magnetic field applied. Hill＇s quantum tunneling model was modified to understand the electrical conduction mechanism in the composites. It shows that the NTC effect ascribes to the dominant thermal activated tunneling transport of electron across adjacent nanoparticles, as well as the low thermal expansivity of epoxy resin matrix.

Fluxing Agents on Ceramification of Composites of MgO-Al2O3-SiO2/Boron Phenolic Resin

Fluxing agents of zinc borate, antimony oxide, galss frit A and glass frit B, with different melting or softening point temperatures, were added into MgO-Al_2O_3-SiO_2/boron phenol formaldehyde resin（MAS/BPF） composites to lower the formation temperature of eutectic liquid phase and promote the ceramification of ceramifiable composites. The effects of fluxing agents on the thermogravimetric properties, phase evolution, and microstructure evolution of MAS/BPF composites were characterized by TG-DSC, XRD and SEM analyses. The results reveal that the addition of a fluxing agent highly reduces the decomposition rate of MAS/BPF composites. Fluxing agents lower the formation temperatures of liquid phases of ceramifiable MAS/BPF composites obviously, and then promote the ceramification and densification process. The final residues of composites are ceramic surrounded by large amount of glass phases.

Synergistic regulation of current-carrying wear performance of resin matrix carbon brush composites with tungsten copper composite powder

Resin matrix carbon brush composites(RMCBCs)are critical materials for high-powered electric tools.However,effectively improving their wear resistance and heat dissipation remains a challenge.RMCBCs prepared with flake graphite powders that were evenly loaded with tungsten copper composite powder(RMCBCs-W@Cu)exhibited a low wear rate of 1.63 mm^(3)/h,exhibiting 48.6%reduction in the wear rate relative to RCMBCs without additives(RMCBCs-0).In addition,RMCBCs-W@Cu achieved a low friction coefficient of 0.243 and low electric spark grade.These findings indicate that tungsten copper composite powders provide particle reinforcement and generate a gradation effect for the epoxy resin(i.e.,connecting phase)in RMCBCs,which weakens the wear of RMCBCs caused by fatigue under a cyclic current-carrying wear.

The application of nanotechnology in the improvement of dental composite resins

In this paper, nanotechnology for the improvement of dental composite resins has been reviewed in the background of the existing shortcomings, focusing on the improvement for polymerization shrinkage, anti-bacterial properties and mechanical properties of composite resins. The results show that the use of nanotechnology and nano materials can be an effective method to improve the performance of dental composite resins in a various ways. At last, the paper also discusses the perspective about the dental composite resins.

Comparative Mechanical Properties of Bulk-Fill Resins

Aim: The aim of this study was to compare the flexural and compressive strengths of a new sonicactivated bulk-fill system (Sonicfill) with other bulk-fill resins and a universal posterior composite resin. Materials and Methods: A low-stress flowable base resin material (SDR), a bulk-fill composite resin (Tetric Evo Ceram), a universal posterior composite (GC G-aenial), and the Sonicfill system were compared. The specimens were prepared for each group following ISO Standard 4049 (flexural strength) and ADA 27 specifications (compressive strength). One-way variance analysis and Kruskal-Wallis tests were used to determine the statistical differences among groups (p 0.05). Results: The Sonicfill system presented significantly higher compressive strength than other groups (p < 0.001). For flexural strength results, although the Sonicfill system showed the highest values, no statistically significant differences were determined among all groups (p > 0.001). Conclusion: Due to the ability to place restorations with single increment and ease of use, the Sonicfill system can be an alternative for posterior restorations.

^(99m)Tc in the evaluation of microleakage of composite resin restorations with SonicFill^(TM).An in vitro experimental model

Introduction: The composite SonicFillTM (Kerr/Kavo) is indicated for posterior restorations, with a single increment up to 5 mm due to reduced polymerization shrinkage, thus reducing working time. Aim: Evaluation of marginal microleakage with SonicFillTM. Method and Materials: There were sectioned sixty noncarious human molars in the occluso-cervical direction. Class V cavities were prepared on each tooth with gingival margin walls in a standardized way. The specimens were divided into 4 groups: group 1—restored with SonicFillTM (Kerr/Kavo), group 2—restored with FiltekTM SupremeXTE (3M ESPE), group 3—the cavities were not restored;group 4—restored with SonicFillTM (Kerr/Kavo). In groups 1, 2 and 4 the enamel was conditioned with 37% orthophosphoric acid and applied the self-etch adhesive system Clear- fillTM SE BOND (Kuraray). The specimens were stored in distilled water at 37?C for 7 days. After, the specimens, were immersed in a solution of 99mTc-Pertechnetate and the radioactivity was assessed with a gamma camera. The nonparametric Kruskal-Wallis and Mann-Whitney test with Bonferroni correction at a significance level of 5% were used for the statistical analyses. Results: There are significant differences between the positive and negative control groups and between these and experimental groups (p TM and FiltekTM SupremeXTE. Conclusion: The new composite SonicFillTM and FiltekTM SupremeXTE showed no difference concerning dye penetration. The Sonic- FillTM restorative system showed no influence in concerning microleakage.

Mechanical Properties, Biocompatibility and Anti-Bacterial Adhesion Property Evaluation of Silicone-Containing Resin Composite with Different Formulae

Novel branched silicone methacrylate was developed.The mechanical and biological properties of the resin system were investigated to select the formula proportion with the best overall performance.The novel silicone-containing monomers were combined with an incremental sequence of glass filler concentrations in commonly used Bis-GMA/TEGDMA(50/50,wt./wt.)dental resin systems.Physicochemical properties,surface properties,antibacterial adhesion effect,anti-biofilm effect,protein adsorption,and cytotoxicity were evaluated.The results showed that BSMs did not affect the double bond conversion of dental resin,but could reduce volumetric shrinkage(p<0.05).The BSM containing resins can resist protein and bacteria adhesion(S.mutans)because it has increased hydrophobicity and a lower free energy surface(p<0.05).However,there were no statistically significant differences in cytotoxicity,surface roughness,and double bond conversion rate.Overall,the results indicate that changes in a material’s properties are not strictly proportional to its composition.Synthetic silicone resin methacrylate can reduce the polymerization shrinkage,have low surface energy and anti-adhesion properties.Silicone composite resin containing 70%matrix has the best comprehensive properties.The silicone methacrylate composite represents an innovative method to improve the properties and reducing secondary caries.

Fracture and Tribological Evaluation of Dental Composite Resins Containing Pre-polymerized Particle Fillers

The fracture and tribological evaluation of dental composite resin containing pre-polymerized particle fillers were investigated. Composite resins, e.g. metafil, silux plus, heliomolar and palfique estelite were selected as specimens in order to evaluate the effects of pre-polymerized particle filler on the fracture and wear characteristics of composite resins. In the wear tests, a ball-on-flat wear test method was used. The friction coefficient of metafil was quite high. The wear resistance of silux plus and palfique estelite was better than that of metafil and heliomolar under the same experimental condition. The main wear mechanism of composite resins containing pre-polymerized particle fillers was an abrasive wear by brittle fracture of pre-polymerized particles and by debonding of fillers and matrix.

Damage and Fatigue Failure of Conventional and Bulk-Filled Resin Composites

Objectives: Resin-based composites are the most widely used dental restorative materials. Bulk-fill resin composites are of rising interest as they can be clinically applied in thicker increments compared to conventional composites. The purpose of the study was to evaluate the flexural fatigue strength of a conventional and bulk-filled resin composite placed incrementally or non-incrementally. Methods: Resin composite specimens were fabricated using either a conventional (Brilliant EverGlow?) or a bulk-fill (Fill-Up!TM) resin composite by either non-incremental filling (2 × 2 × 25 mm3) or in increments of (1 × 2 × 25 mm3). Specimens were stored in distilled water for 24 h or thermocycled for 5000 cycles. The static flexural strength (σ), flexural fatigue limit (FFL) after 105 cycles and post-fatigue flexural strength (PFσ) were measured. Data were analyzed using ANOVA, with a post-hoc Tukey’s test to compare mean FFL (p σ and PFσ compared to conventional composites regardless of incremental cure or thermocycling (p σ and FFL for conventional composites but not bulk-filled composites. There was no significant difference in PFσ compared to σ after 24 h storage, but a significant increase in PFσ after thermocycling (p < 0.05). Conclusions: The type of composite rather than incremental placement had a greater effect on flexural strength, suggesting that operator placement technique had less influence than material selection. Thermocycling in combination with cyclic loading caused a strengthening effect in the composites, likely due to the absorption and dissipation of stresses, thereby enhancing resistance to fracture.

Antibacterial Dental Resin Composites: A Narrative Review

Lack of antibacterial properties in resin-based composites (RBCs) is one of the flaws that cause the failure of filling clinically. Several agents have been incorporated to endow RBCs with antibacterial properties. In this review, we summarize the recent antibacterial agents between 2015 and 2020 using keywords of antibacterial or antimicrobial dental resin composites by PubMed databases. The most effective strategies are concerned with polymerizable monomers (50%), followed by filler particles (39%) and leachable agents (11%). A recent modification of the antibacterial agent is either by combining two agents from the same category or mixing agents from different categories in one. More than two methods were used in one study to assess antibacterial efficacy. The most common method was biofilm colony-forming units (CFUs) counting method (40%), followed by live/dead bacteria staining assay of biofilms (25%), metabolic activity assay of biofilms using MTT assay (16%), lactic acid production assay of biofilms (8%), agar diffusion test (8%), and other methods (3%) such as minimal inhibitory concentration (MIC) and minimal bactericidal concentration (MBC).

Comparison of One-Step and Multistep Polishing Systems for the Surface Roughness of Resin Composites

Aim: This study analyzed the effect of different finishing and polishing systems on the surface roughness of a microfilled (Amaris), and a nanofilled resin composite (Clearfil Majesty Esthetic) using Scanning electron microscope (SEM) analysis and surface roughness tester. Materials and Methods: Thirty five specimens of each material were prepared in a plexiglass mold (10 mm in diameter and 2 mm in depth) and cured against a Mylar matrix strip to create a baseline surface. The average surface roughness was measured using a surface profilometer (Mahr Perthometer SP4, Germany) in three different positions on each sample before and after finishing with one of the seven finishing procedures: Procedure 1: Mylar strip (control), Procedure 2: Tungsten carbide burs, Procedure 3: Diamond burs, Procedure 4: Procedure 2 + one-step diamond micropolisher (PoGo), Procedure 5: Procedure 2 + multi-step discs (Super-snap), Procedure 6: Procedure 3 + one-step diamond micropolisher (PoGo), Procedure 7: Procedure 3 + multi-step discs (Super-snap). The obtained data were analyzed using two-way analysis of variance (ANOVA) and Duncan test at a p = 0.05 significance level. Results: Nanofilled composite showed significantly lower Ra values than microfilled composite in procedures 4, 6 and 7 (p 0.05). Conclusion: Nanofilled resin composite showed significantly lower Ra values than microfilled resin composite. Regardless of finishing methods, diamond micro-polisher produced smoother surfaces than polishing discs.

Effect of Universal Primers on the Tensile Bond Strength between Zirconia and Resin Composites

This study aimed to evaluate the effects of universal primers on the tensile bond strength between zirconia and resin composites.Zirconia specimens were divided into five groups based on the surface treatment with the following primers:MP(Monobond Plus),SU(ScotchBond Universal),AZ(AZ Primer),BM(Beauty bond Multi),and BL(Bondmer Lightless).After priming,stainless steel rods were bonded to the zirconia specimens with composite resin.The tensile bond strength test was performed:stored at room temperature for 1 day;stored in distilled water at 37°C for 7 days;and underwent thermal cycling.The BL group demonstrated a significantly higher tensile bond strength than other groups when stored at room temperature for 1 day(p<0.05).The primer that acted via chemical polymerization appeared to be most effective in improving the bond strength between the two materials in this study.

MICROLEAKAGE OF CLASS V RESIN-MODIFIED GLASS IONOMER CEMENT AND COMPOMER RESTORATIONS IN VITRO

Objective To assess the microleakage of Class V restorations made with two resin-modified glass ionomer cements （RMGICs） and two polyacid-modified composite resins （PMCRs）. Methods Restorations of the four materials （ GC Fuji Ⅱ LC, Vitremer^TM, Dyract AP and F2000^TM ） were placed in facial Class V cavity preparations in forty noncarious human molar teeth. Teeth were randomly assigned to 4 experimental groups of 10 teeth each. After thermal cycling（ ×20, 5 -55℃ ） , the interface between dentin and restorations was spattercoated with gold and observed under scanning electron microscopy （SEM）. Then the square and average width of margin gaps of central 1/3 interface were recorded with image analysis software. Results The data indicated no significant differences between all the restorative materials for both occlusal and gingival margins. Further analysis revealed there were statistically significant differences between occlusal margins and gingival margins for VitremerTM and Dyract AP, respectively. Conclusion None of the tested materials guaranteed margins free of microleakage. Resin-modified glass ionomer cements showed similar margin gaps to the polyacid-modified composite resins tested.

Urchin-like multiscale structured fluorinated hydroxyapatite as versatile filler for caries restoration dental resin composites

Caries is one of the most prevalent human diseases,resulting from demineralization of tooth hard tissue caused by acids produced from bacteria,and can progress to pulpal inflammation.Filling restoration with dental resin composites(DRCs)is currently the most common treatment for caries.However,existing DRCs suffer from low fracture strength and lack comprehensive anti-caries bioactivity including remineralization,pulp protection,and anti-cariogenic bacteria effects.In this study,inspired by plant roots’ability to stabilize and improve soil,fluorinated urchin-like hydroxyapatite(FUHA)with a three-dimensional whisker structure and bioactive components of calcium,phosphorus,and fluorine was designed and synthesized by a dynamic self-assembly method.Furthermore,versatile FUHA particles with different loading fractions were used as functional fillers to fabricate methacrylate-based DRCs,where the urchin-like hydroxyapatite(UHA)filled DRCs and commercial DRCs(Z350XT and BEAUTIFIL II)served as the control groups.The results demonstrated that FUHA with 50 wt%loading in resin matrix endowed DRC(F5)with excellent physicochemical properties,dentin remineralization property,cell viability,promotion of dental pulp stem cells mineralization,and antibacterial properties.Meanwhile,F5 also presented good clinical handling and aesthetic characteristics.Therefore,structure/functional-integrated FUHA filled DRCs have potential as a promising strategy for tooth restoration and anti-caries bioactivity.