Temperature distribution and effect of low-density electric current on B2+O lamellar microstructure of Ti_2AlNb alloy sheet during resistance heating

The resistance heating method has been one of the prospective techniques for hot processing and welding techniques. The thermal behavior under different densities of electric current and the effect of electric current at temperature of 780 oC using low density of electric current of 6.70 A/mm^2 on the B2+O lamellar microstructure were investigated for Ti2AlNb alloy sheet. The stable temperature denoted a balanced state between the Joule heat and the dissipation of heat including heat conduction, convection and radiation while the distribution of temperature was nonuniform. The highest temperatures of electric current heating samples increased as the density of electric current was elevated. In order to understand the specific effect of electric current on B2+O microstructure, heat treatment for microstructural homogeneity was introduced to this study. After that, according to the microstructural observations by common characterization techniques in the resistance-heating sample and the isothermal furnace-heating sample after homogenizing treatment, few significant differences in content and orientation of phases can be directly and explicitly found except the thermal effect from the applied electric current. The results will provide reference to this prospective forming and welding techniques and the application for Ti2AlNb alloys using resistance heating in the near future.

Evaluation of high-temperature tensile behavior for metal foils by a novel resistance heating assisted tensile testing system using samples with optimized structures

To evaluate the tensile behavior of metal foils by resistance heating(RH)assisted tensile testing system accurately,this study proposed to embed a digital image correlation(DIC)system with laser speckles for the measurement of full-field strain distribution.Furthermore,the sample structures were optimized to achieve uniform temperature and strain distribution.An infrared camera was used to monitor the temperature distribution.Rectangular samples instead of dog-bone shaped samples were proposed.A model for calculating the temperature distribution was established to optimize the sample structure.The parameters that influence the temperature distribution and tensile behavior were studied.As results,compared to the strain measured by a non-contact extensometer,the maximum deviation of the strain measured by DIC was less than 6%when the nominal strain was larger than 0.013.It is confirmed that the proposed tensile testing system is reliable for measuring the temperature and full-field strain distributions.Sample shape influenced temperature distributions of smaller samples while it almost had no influence on the temperature distributions of larger samples.The temperature difference was not affected by the material type but by the sample size.The proposed rectangular shape was validated to be feasible for RH assisted tensile testing.The sample length was successfully optimized for a more uniform temperature distribution by the established model.Although the tensile deformation was not influenced by the sample shape,the temperature distribution resulted in a non-uniform strain distribution before achieving ultimate tensile strength.Longer effective sample length between two clamping jigs contributed to a more uniform temperature distribution and material deformation.A more accurate evaluation of high-temperature tensile behavior for metal foils can be achieved by the proposed RH assisted tensile testing system using rectangular samples with an optimized structure.

Combination of steam-enhanced extraction and electrical resistance heating for efficient remediation of perchloroethylene-contaminated soil:Coupling merits and energy consumption

In situ thermal desorption(ISTD)technology effectively remediates soil contaminated by dense nonaqueous phase liquids(DNAPLs).However,more efforts are required to minimize the energy consumption of ISTD technology.This study developed a laboratory-scale experimental device to explore the coupling merits of two traditional desorption technologies:steam-enhanced extraction(SEE)and electrical resistance heating(ERH).The results showed that injecting high-density steam(>1 g/min)into loam or clay with relatively high moisture content(>13.3%)could fracture the soil matrix and lead to the occurrence of the preferential flow of steam.For ERH alone,the electrical resistance and soil moisture loss were critical factors influencing heating power.When ERH and SEE were combined,preheating soil by ERH could increase soil permeability,effectively alleviating the problem of preferential flow of SEE.Meanwhile,steam injection heated the soil and provided moisture for maintaining soil electrical conductivity,thereby ensuring power stability in the ERH process.Compared with ERH alone(8 V/cm)and SEE alone(1 g/min steam),the energy consumption of combined method in remediating perchloroethylene-contaminated soil was reduced by 39.3%and 52.9%,respectively.These findings indicate that the combined method is more favorable than ERH or SEE alone for remediating DNAPL-contaminated subsurfaces when considering ISTD technology.

Effect of intermetallic compounds on heat resistance of hot roll bonded titanium alloy-stainless steel transition joint

The effect of intermetallic compounds on the heat resistance of transition joint was investigated. The experiment of post-weld heat treatment for the hot roll bonded titanium alloy-stainless steel joint using nickels interlayer was carried out, and the interface microstructure evolution due to heat treatment was presented. There was not found significant interdiffusion at stainless steel/nickel interface, when the specimens were heat treated in the temperature range of 600-800 °C for 10 and 30 min, while micro-cracks occurred at the stainless steel/nickel interface heat treated at 700 °C for 30 min. The thickness of intermetallic layers at nickel/titanium alloy interface increased at 600 °C, and micro-cracks occurred at 700 and 800 °C. The micro-cracks occurred between intermetallic layers or between intermetallic layer and nickel interlayer as well. The tensile strength of the transition joint decreased with the increase of heat treatment temperature or holding time.

Current progress of research on heat -resistant Mg alloys: A review

With the increasing attention received by lightweight metals,numerous essential fields have increased requirements for mag-nesium(Mg)alloys with good room-temperature and high-temperature mechanical properties.However,the high-temperature mechanic-al properties of commonly used commercial Mg alloys,such as AZ91D,deteriorate considerably with increasing temperatures.Over the past several decades,extensive efforts have been devoted to developing heat-resistant Mg alloys.These approaches either inhibit the gen-eration of thermally unstable phases or promote the formation of thermally stable precipitates/phases in matrices through solid solution or precipitation strengthening.In this review,numerous studies are systematically introduced and discussed.Different alloy systems,includ-ing those based on Mg–Al,Mg–Zn,and Mg–rare earth,are carefully classified and compared to reveal their mechanical properties and strengthening mechanisms.The emphasis,limitations,and future prospects of these heat-resistant Mg alloys are also pointed out and dis-cussed to develop heat-resistant Mg alloys and broaden their potential application areas in the future.

Effect of Mn addition on microstructure and mechanical properties of GX40CrNiSi25-12 austenitic heat resistant steel

Three types of steels were designed on the basis of GX40CrNiSi25-12 austenitic heat resistant steel by adding different Mn contents(2wt.%,6wt.%,and 12wt.%).Thermodynamic calculation,microstructure characterization and mechanical property tests were conducted to investigate the effect of Mn addition on the microstructure and mechanical properties of the austenitic heat resistant steel.Results show that the matrix structure in all the three types of steels at room temperature is completely austenite.Carbides NbC and M_(23)C_(6)precipitate at grain boundaries of austenite matrix.With the increase of Mn content,the number of carbides increases and their distribution becomes more uniform.With the Mn content increases from 1.99%to 12.06%,the ultimate tensile strength,yield strength and elongation increase by 14.6%,8.0%and 46.3%,respectively.The improvement of the mechanical properties of austenitic steels can be explained by utilizing classic theories of alloy strengthening,including solid solution strengthening,precipitation strengthening,and grain refinement.The increase in alloy strength can be attributed to solid solution strengthening and precipitation strengthening caused by the addition of Mn.The improvement of the plasticity of austenitic steels can be explained from two aspects:grain refinement and homogenization of precipitated phases.

Effect of Interface Form on Creep Failure and Life of Dissimilar Metal Welds Involving Nickel-Based Weld Metal and Ferritic Base Metal

For dissimilar metal welds(DMWs)involving nickel-based weld metal(WM)and ferritic heat resistant steel base metal(BM)in power plants,there must be an interface between WM and BM,and this interface suffers mechanical and microstructure mismatches and is often the rupture location of premature failure.In this study,a new form of WM/BM interface form,namely double Y-type interface was designed for the DMWs.Creep behaviors and life of DMWs containing double Y-type interface and conventional I-type interface were compared by finite element analysis and creep tests,and creep failure mechanisms were investigated by stress-strain analysis and microstructure characterization.By applying double Y-type interface instead of conventional I-type interface,failure location of DMW could be shifted from the WM/ferritic heat-affected zone(HAZ)interface into the ferritic HAZ or even the ferritic BM,and the failure mode change improved the creep life of DMW.The interface premature failure of I-type interface DMW was related to the coupling effect of microstructure degradation,stress and strain concentrations,and oxide notch on the WM/HAZ interface.The creep failure of double Y-type interface DMW was the result of Type IV fracture due to the creep voids and micro-cracks on fine-grain boundaries in HAZ,which was a result of the matrix softening of HAZ and lack of precipitate pinning at fine-grain boundaries.The double Y-type interface form separated the stress and strain concentrations in DMW from the WM/HAZ interface,preventing the trigger effect of oxide notch on interface failure and inhibiting the interfacial microstructure cracking.It is a novel scheme to prolong creep life and enhance reliability of DMW,by means of optimizing the interface form,decoupling the damage factors from WM/HAZ interface,and then changing the failure mechanism and shifting the failure location.

Improvements of heat resistance and adhesive property of condensed poly-nuclear aromatic resin via epoxy resin modification

A bisphenol epoxy resin was used as modifier to increase the heat resistance of condensed poly-nuclear aromatic （COPNA） resin. The basic properties of COPNA resin and modified resin were characterized by Fourier transform infrared spectroscopy （FT-IR）, nuclear magnetic resonance spectroscopy （1H-NMR）, vapor pressure osmometry （VPO） and elemental analysis （EA）. Average structural parameters of resins were calculated by the improved Brown-Ladner method, and heat resistance of resins was tested by thermogravimetric analysis （TGA）. The chemical structure, mechanical properties and heat resistivity of the resin/graphite composites prepared with different resins were compared. The results show that the adhesive property and heat resistance of COPNA resin can be remarkably improved by addition of 5 wt.% epoxy resin. The reason is that the reactions between epoxy groups of epoxy resin and hydroxyl groups of COPNA resin improve the heat resistance and adhesive property of COPNA resin. Electric motor brushes with good mechanical properties and low electrical resistivity were successfully prepared by using the modified resin as binder.

Effects of composite scale on high temperature oxidation resistance of Fe-Cr-Ni heat resistant alloy

Fe-Cr-Ni heat resistant alloys with aluminum and silicon addition, alone and in combination, were melted using an intermediate frequency induction furnace with a non-oxidation method. By the oxidation weight gain method, the oxidation resistances of the test alloys were determined at 1,200 ℃ for 500 hours. According to the oxidation weight gains, the oxidation kinetic curves were plotted and the functions were regressed by the least squares method. The results show that the oxidation kinetic curves follow the power function of y = ax^b （a〉0, 0〈b〈1）. The effects of scale compositions on oxidation resistance were studied further by analyses using X-ray diffraction （XRD） and scanning electron microscope （SEM）. It is found that the composite scale compounds of Cr203, a-Al2O3, SiO2 and FeCr2O4, with compact structure and tiny grains, shows complete oxidation resistance at 1,200℃. When the composite scale lacks a-Al2O3 or SiO2, it becomes weak in oxidation resistance with a loose structure. By the criterion of standard Gibbs formation free energy, the model of the nucleation and growth of the composite scale is established. The forming of the composite scale is the result of the competition of being oxidized and reduced between aluminum, silicon and the matrix metal elements of iron, chromium and nickel. The protection of the composite scale is analyzed essentially by electrical conductivity and strength properties.

IMPROVEMENT OF TYPE IV CRACKING RESISTANCE OF 9Cr HEAT RESISTING STEEL WELDMENT BY BORON ADDITION

Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affected zone (HAZ). Because boron is considered to suppress the coarsening of grain boundary precipitates and growth of creep voids, we have investigated the effect of boron addition on the creep properties of 9Cr steel weldments. Four kinds of 9Cr3WSCoVNb steels with boron content varying from 4.7×10-5 to 1.8×10-4 and with nitrogen as low as 2.0×10-5 were prepared. The steel plates were welded by gas tungsten arc welding and crept at 923K. It was found that the microstructures of HAZ were quite different from those of conventional high Cr steels such as P91 and P92, namely the fine-grained HAZ did not exist in the present steel weldments. Boron addition also has the effect to suppress coarsening of grain boundary carbides in HAZ during creep. As a result of these phenomena, the welded joints of present steels showed no Type Ⅳ fractures and much better creep lives than those of conventional steels.

Micro-analysis of high-temperature oxidation-resistance of a new kind of heat-resistant grid plate in grate-kiln

To further improve the oxidation-resistance of materials and reduce the cost of grid plates in grate-kiln, a new kind of heat-resistant grid plate was developed. The microstructure of this grid plate with a life more than 18 months was studied by XRD, SEM and EDS techniques. The results show that high hardness, high intensity and good impact property make the new kind of heat-resistant grid plate and its oxide film have a higher resistance to deformation and abrasion at 900-1000℃ Besides, small grain size is beneficial to form a complete protective oxide film. The oxide film composed of SiO2 layer, Cr2O3 layer and Fe2O3 layer is rather thin and bonds closely with the backing. The forming of the chemical stable nickel-rich layer increases the density of Cr2O3 layer.

Formation Mechanism and Existing Form of Sb in Heat Resistance Mg-Gd-Y-Sb Alloy

The existing form and reaction mechanism of Sb in heat resistane Mg-Gd-Y-Sb rare earth magnesium alloy were investigated by inductive coupled plasma emission spectroscopy(ICP),scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),and X-ray diffraction(XRD).It is found that Sb tends to form high melting point intermetallics with rare earth elements of Gd and Y.The existing form of Sb is determined to be GdSb and SbY,respectively,which has high melting point(GdSb:2142℃/SbY:1782℃).Meanwhile,the first principle calculation and electronegativity difference calculation were performed to further understand the reaction mechanism.Therefore,the forming heat and binding energy were calculated.The experimental results show that the binding tendency of Sb element to Gd and Y is much stronger than that of it with other elements in this alloy,which results in the formation of high melting point of Gd-Sb and Y-Sb intermetallics,and finally leads to the high temperature resistant further improvement of the Mg-Gd-Y magnesium alloy.

Heat Resistance of TiN Coated HSS Tools

The cutting friction, cutting deformation, producing heat, conducting heat, temperature field of TiN coated HSS tools in the cutting process are discussed profoundly. In order to make clear the heat property of TiN coated tools, from the micromechanism angle, the relationship of the heat property and the crystal structure of TiN compound is analyzed, and the regularity of TiN compound crystal structure changing with temperature rising is sought. The difference of the wear resistance and heat resistance of TiN coated tools deposited by c1 and c2 depositing techniques is proved by tests. The conclusions will offer the theoretical basis for correct design of geometrical parameters of TiN coated tools, rational selection of cutting regimes and optimization of the depositing technique.

Effect of Aluminium and Silicon on High Temperature Oxidation Resistance of Fe-Cr-Ni Heat Resistant Steel

Fe-Cr-Ni heat resistant steels with different contents of Al and Si were cast in intermediate frequency induction furnace with non-oxidation method. With oxidation weight gain method, the oxidation resistance of test alloys was examined at 1 200 ℃ for 500 h. The effects of Al and Si on oxidation resistance were studied through analyses of X-ray diffraction （XRD） and scanning electron microscope （SEM）. It is shown that the composition of oxide scales is a decisive factor for the oxidation resistance of heat resistant steels. The compounded scale composed of Cr203, α-Al2O3, SiO2 and Fe （Ni）Cr2O4, with flat and compact structure, fine and even grains, exhibits complete oxidation resistance at 1 200 ℃. Its oxidation weight gain rate is only 0.081 g/（m^2.h）. By the criterion of standard Gibbs formation free energy, a model of nucleation and growth of the compounded scale was established. The formation of the compounded scale was the result of the competition of being oxidated and reduction among Al, Si, and the matrix metal elements of Fe, Cr and Ni. The protection of the compounded scale was analyzed from the perspectives of electrical conductivity and strength properties.

A Study on Heat Resistance and Initial Characterization of Protease Inhibitors in Porcine Colostrum

Porcine colostrum was separated into the acid soluble fraction (SF) and casein fraction (CF) by acidifying followed by centrifuge. SF was further separated by liquid chromatography and anisotropic membrane filtration. Capacities of the SF or CF of porcine colostrum, to inhibit trypsin and chymotrypsin activity and to inhibit the epidermal growth factor (EGF) degradation in pig small intestinal contents, were determined under different heat treatments. The study showed that trypsin inhibitors in porcine colostrum survived heat treatments of 100℃ water bath for up to 10 min, but exposure to boiling water bath for 30 min significantly decreased the inhibitory activity. Compared with the trypsin inhibitors, the chymotrypsin inhibitors were more heat sensitive. SF was more heat sensitive than CF. Separation of the SF of porcine colostrum by liquid chromatography and anisotropic membrane filtration revealed that the porcine colostrum protease inhibitors, those had the capacity to inhibit the trypsin chymotrypsin activity and enhanced the stability of EGF in the gastrointestinal(GI) lumen of weaned pigs, existed mainly in SF, milk derived, were a group of heat labile small proteins with molecular weight of 10 00050 000.

Heat Resistance of Rice Landrace D43 at Anthesis

Rice is extremely sensitive to high temperature, especially at the fowering stage. Identifying new germplasm and breeding heat-resistant rice varieties are therefore essential. After multi-year evaluations, a heat-resistant rice landrace D43 was identifed in our previous research. In this study, the relationship between heat resistance and flower opening time （FOT） was analyzed both in the field and in phytotron. The results showed that high temperature could accelerate fower opening of a range of rice varieties. The D43 showed early morning fowering （EMF） habit in different conditions, and the FOT of which was mainly concentrated in the period of 8：30~10：00 AM under high temperature. The spikelet fertility of D43 was relatively low after exposure to invariably high temperature during fower opening. However, the EMF habit of D43 was conducive to avoiding mid-day high temperature, and therefore increased the spikelet fertility under rising high temperature conditions in the feld and in phytotron. In addition, morphological traits including the anther dehiscence rate, the total number and germinated number of pollens on the stigma were signifcantly correlated with the spikelet fertility, and therefore they could be used to evaluate rice heat resistance at anthesis.

Wire arc additive manufacturing of a heat-resistant Al-Cu-Ag-Sc alloy:microstructures and high-temperature mechanical properties

With a high energy efficiency,low geometric limitation,and low cracking susceptivity to cracks,wire arc additive manufacturing(WAAM)has become an ideal substitute for casting in the manufacturing of load-bearing high strength aluminum components in aerospace industry.Recently,in scientific researches,the room temperature mechanical performance of additive manufactured high strength aluminum alloys has been continuously broken through,and proves these alloys can achieve comparable or even higher properties than the forged counterpart.Since the aluminum components for aerospace usage experience high-low temperature cycling due to the absence of atmosphere protection,the high temperature performances of additive manufactured high strength aluminum alloys are also important.However,few research focuses on that.A special 2319Ag Sc with 0.4 wt.%Ag and 0.2 wt.%Sc addition designed for high temperature application is deposited successfully via cold metal transfer(CMT)based on WAAM.The microstructures and high temperature tensile properties are investigated.The results show that the as-deposited 2319Ag Sc alloy presents an alternate distribution of columnar grains and equiaxed grains with no significant textures.Main second phases are Al_(2)Cu and Al3Sc,while co-growth of Al_(2)Cu and bulk Al_(3)Sc is found on the grain boundary.During manufacturing,nanoscale Al_(2)Cu can precipitate out from the matrix.Ag and Mg form nano-scaleΩphase on the Al_(2)Cu precipitates.At 260℃,average yield strengths in the horizontal direction and vertical direction are 87 MPa±2 MPa,87 MPa±4 MPa,while average ultimate tensile strengths are 140 MPa±7 MPa,141 MPa±11 MPa,and average elongations are 11.0%±2.5%,13.5%±3.0%.Anisotropy in different directions is weak.

Synthesis, Characterization and Properties of Polymeric p-Benzoyl-4,4'-Diaminobenzoylaniline

An aromatic polyamide was synthesized by low-temperature poly-condensation reaction from terephthaloyl chloride and 4,4'-diaminobenzanilide (4,4'-DABA). The synthesized polyamide had a characteristic peak of carbon atoms in the amide group at 166 ppm, which was demonstrated by the solid nuclear magnetic resonance carbon spectrum. It was shown to be the stretching vibration absorption peak of the amide N-H bond at 3342 cm−1 by Fourier infrared (FT-IR) spectroscopy. It was obtained that the energy band near 1100 - 1276 cm−1 belongs to the absorption peak of the para-substituted benzene ring and the band near 2977 cm−1 was the C-H stretching vibration peak of the benzene ring by Raman spectroscopy. The molecular structure of the synthesized polyamide compound was confirmed by FT-IR, Raman, and solid 13C-NMR spectroscopies. It was proved that the polymer is stable up to 300˚C and has a relatively high stability by the thermogravimetric analysis. It was also confirmed by the fluorescence spectrum that it has a strong blue fluorescence near 420 nm. The morphological characteristics of the polymer were further demonstrated by electron scanning electron microscopy (SEM). The properties of polymeric p-benzoyl-4,4'-diaminobenzoyl-aniline were found to emit strong blue fluorescence and have good thermal stability, making it a promising functional material for fluorescence in the blue region with potential for large-scale applications.

Analysis of Metallographic Characteristics of Aluminum Alloy for Turbocharged Impellers

In this paper, the composition, two-dimensional and three-dimensional microstructure of heat-resistant wrought aluminum alloy with strong oxidation resistance, heat resistance and easy processing are analyzed by using direct reading spectrometer, metallographic microscope and scanning electron microscope. The main alloy elements of heat-resistant forging aluminum alloy include Cu, Mg, Si, Ni and Fe. The α solid solution of each element in aluminum consists of S phase (Al2CuMg), Mg2Si phase, bright gray Al2CuNi phase and dark brown Al9FeNi phase. The distribution of each phase in the aluminum alloy is determined by the three-dimensional energy spectrum analysis of the microstructure, and the distribution of each phase in the crystal position is analyzed. The mechanism of heat resistance, easy processing type and wear resistance is obtained, which provides the theoretical basis for the development and use of heat-resistant forged aluminum alloy.

Weatherability and heat resistance enhanced by interaction between AG25 and Mg/AI-LDH

Although inorganic pigments in common spectral tuning materials show good weatherability and heat resistance,the limited color choices,weak coloring power,poor dispersibility,and a possibility of toxicity limit their development.On the basis of organic pigments which possess a wide range of colors,high coloring power,good transparency,and high safety,herein,the modified pigment and biomimetic coating with improved weatherability,especially ultraviolet(UV)resistance(from 2 to 6 days),was achieved by intercalating acid green 25(AG25)pigment into Mg/Al-layered double hydroxides(Mg/Al-LDH).Furthermore,the heat resistance of AG25 was also significantly increased.Moreover,the spectral stability of pigments after heat treatment is superior with almost unchanged spectral profile and green reflection peak.The formation of strong N-H bonds and the S-M(Mg,Al)bonds between Mg/Al-LDH laminates and AG25 molecules contributes to the improvement.This work shows potential for biomimetic leaf materials in respect of reflective spectra stability.