Thermal resistance matrix representation of thermal effects and thermal design in multi-finger power heterojunction bipolar transistors

The thermal resistance matrix including self-heating thermal resistance and thermal coupling resistance is presented to describe the thermal effects of multi-finger power heterojunction bipolar transistors. The dependence of thermal resistance matrix on finger spacing is also investigated. It is shown that both self-heating thermal resistance and thermal coupling resistance are lowered by increasing the finger spacing, in which the downward dissipated heat path is widened and the heat flow from adjacent fingers is effectively suppressed. The decrease of self-heating thermal resistance and thermal coupling resistance is helpful for improving the thermal stability of power devices. Furthermore, with the aid of the thermal resistance matrix a 10-finger power heterojunction bipolar transistor （HBT） with non-uniform finger spacing is designed for high thermal stability. The optimized structure can effectively lower the peak temperature while maintaining a uniformity of the temperature profile at various biases and thus the device effectively may operate at a higher power level.

Resistance Matrix for an Anisotropic Hall Plate with Multiple Extended Asymmetric Contacts on the Boundary

The electrical properties of magnetic sensing devices fabricated from anisotropic materials are not easily extracted. Here we present a method for determining the resistance matrix for an anisotropic device with multiple electrical contacts placed in a perpendicular magnetic field. By using the methods developed by Van der Pauw and Wasscher, the analysis for the anisotropic system is reduced to the equivalent problem for an isotropic sample, which can then be solved using methods developed previously. As a result, the method works in the case of structures with an arbitrary number of asymmetric extended contacts at large magnetic field strength. In addition to the extraction of nonisotropic resistivities, the resistance matrix can be used to analyze the Hall effect for anisotropic plates.

TiC颗粒弥散强化不同基体钢的磨损性能研究

运用原位合成工艺制备出TiC颗粒弥散强化不同基体的钢种,TiC颗粒在强化钢中分布均匀。结果表明:钢中合金元素越多,TiC与基体的结合强度越低,室温强度提高幅度越小。TiC颗粒能够提高低合金钢的磨损性能。但是,高合金钢中的TiC颗粒容易剥落成为磨粒从而恶化磨损性能。

Effect of Salt Spray Corrosion on Tribological Properties of HVOF Sprayed NiCr-Cr3C2 Coating with Intermediate Layer

The objective of the present work was to determine the influence of the neutral salt spray corrosion on the wear resistance of HVOF sprayed NiCr-Cr3C2 coating with intermediate layer. Ni-Zn-Al2O3 coatings as interlayers were prepared by low pressure cold spray（LPCS） between NiCr-Cr3C2 cermet coatings to form a sandwich structure to enhance the corrosion resistance properties. The tribological properties were examined using the UMT-3 fricition and wear tester by line-contact reciprocating sliding under dry and salt spray one week corrosion. The morphology, element distribution, and phase compositions of the coating and worn sufaces were analyzed by using scanning electron microscopy, energy dispersive spectrometry, and X-ray diffraction respectively. The corrosion behavior of the coating was studied by the open-circuit potential, the electrochemical impedance spectroscopy, potentiodynamic polarization, and salt spray corrosion methods. It is found that the sandwich structured coating has better corrosion resistance than the single layer coating. The results show that under dry wear conditions, the wear mechanism is abrasive and adhesive wear, whereas under salt spray corrosion conditions it becomes corrosion wear. The friction coefficient of the sandwich structured coating after salt spray corrosion is slightly lower than the dry friction coefficient, but the weight of the wear loss is lower than that under dry condition.

Effect of graphite content on wear property of graphite/Al_2O_3/Mg-9Al-1Zn-0.8Ce composites

Using squeeze-infiltration technique, Mg-9Al-1Zn-0.8Ce composite reinforced by graphite particles and Al2O3 short fibers was fabricated. The reinforcing phases combined closely with the matrix and no agglomeration was observed. The microstructure, hardness and wear property of the composites with the graphite content of 5%, 10%, 15% and 20% were investigated, respectively. The results reveal that Ce tends to enrich around the boundaries of graphite particles and Al2O3 short fibers, and forms Al3Ce phase. When the graphite content increases to 20%, the grain size becomes small. Moreover, with increasing the graphite content, the microhardness of the composites decreases but the wear resistance increases. The graphite which works as lubricant during dry sliding process decreases the wear loss. At low load, the wear mechanism of the composite is mainly abrasive wear and oxidation wear; at high load, except that the composite with 20% graphite is still with abrasive wear and oxidation wear, the wear mechanism of other composites changes to delamination wear.