Analysis of Quenching Resistor Effect to Improve Stability of TIA Circuit for APD-A Secondary Publication

In this paper,since the Avalanche Photo Diode(APD)for Light-to-Voltage LTV conversion uses a high voltage in the operating range unlike other Photo Diodes(PD),the quenching resistor must be connected in series to prevent overcurrent when using the Transimpedance Amplifier(TIA).In such a case,quenching resistance may affect the transfer function of the TIA circuit,resulting in serious stability.Therefore,in this paper,by analyzing the effect of APD quenching resistance on the voltage and current loop transfer function of TIA,we proposed a loop analysis and a method for determining the quenching resistance value to improve stability.A TIA circuit with quenching resistance was designed by the proposed method and its operational stability was verified through simulation and chip fabrication.

Energy model based sensorless estimation method for operational temperature of braking resistor onboard metro vehicles

Purpose–This study aims to improve the availability of regenerative braking for urban metro vehicles by introducing a sensorless operational temperature estimation method for the braking resistor(BR)onboard the vehicle,which overcomes the vulnerability of having conventional temperature sensor.Design/methodology/approach–In this study,the energy model based sensorless estimation method is developed.By analyzing the structure and the convection dissipation process of the BR onboard the vehicle,the energy-based operational temperature model of the BR and its cooling domain is established.By adopting Newton’s law of cooling and the law of conservation of energy,the energy and temperature dynamic of the BR can be stated.To minimize the use of all kinds of sensors(including both thermal and electrical),a novel regenerative braking power calculation method is proposed,which involves only the voltage of DC traction network and the duty cycle of the chopping circuit;both of them are available for the traction control unit(TCU)of the vehicle.By utilizing a real-time iterative calculation and updating the parameter of the energy model,the operational temperature of the BR can be obtained and monitored in a sensorless manner.Findings–In this study,a sensorless estimation/monitoring method of the operational temperature of BR is proposed.The results show that it is possible to utilize the existing electrical sensors that is mandatory for the traction unit’s operation to estimate the operational temperature of BR,instead of adding dedicated thermal sensors.The results also validate the effectiveness of the proposal is acceptable for the engineering practical.Originality/value–The proposal of this study provides novel concepts for the sensorless operational temperature monitoring of BR onboard rolling stocks.The proposed method only involves quasi-global electrical variable and the internal control signal within the TCU.

Three Dimensional Electric Circuits with Multiple Capacitors and Resistors

Two cubical 3D electric circuits with single and double capacitors and twelve ohmic resistors are considered. The resistors are the sides of the cube. The circuit is fed with a single internal emf. The charge on the capacitor(s) and the current distributions of all twelve sides of the circuit(s) vs. time are evaluated. The analysis requires solving twelve differential-algebraic intertwined symbolic equations. This is accomplished by applying a Computer Algebra System (CAS), specifically Mathematica. The needed codes are included. For a set of values assigned to the elements, the numeric results are depicted.

3D_Multi Resistor Electric Circuit

This report addresses the issues concerning the analysis of an electric circuit composed of multiple resistors configured in a 3-Dimension structure. Noting, all the standard textbooks of physics and engineering irrespective of the used components are circuits assembled in two dimensions. Here, by deviating from the “norm” we consider a case where the resistors are arranged in a 3D structure;e.g., a cube. Although, independent of the dimension of the design the same physics principles apply, transitioning from a 2D to a 3D makes the corresponding analysis considerably challenging. In general, with no exception, depending on the used components the analysis faces with solving a set of either algebraic or differential-algebraic equations. Practically, this interfaces with a Computer Algebra System (CAS). The main objective is symbolically to identify the current distributions and the equivalent resistor (s) of cubically assembled resistors.

Systematic design method for PI controller with Virtual Resistor-based Active Damping of LCL filter

The Virtual Resistor based Active Damping(VR-AD) is widely employed in converters connected to the grid via LCL filters in order to mitigate the inherent resonance of the filters. Nevertheless, in digitally controlled systems, the PWM and the calculating delays modify the system characteristics in terms of frequency and phase, thus destabilizing the system and degrading the VR-AD performances, mainly in low switching frequencies. Moreover, the stability of the system is greatly affected under weak grid operation characterized by large grid impedance variation. This paper solves these problems by proposing a systematic, robust and optimized design procedure of voltage oriented PI control(VOC) with VRAD. The considered design procedure ensures robust control(sufficient stability margins) and high quality of grid current(reduced steady-state error and minimized THD value) despite the negative impact of digital time delay, grid impedance variation and filter parameters change. Simulation and experimental results are presented to show robustness and efficiency of the suggested design procedure.

Current dependence coefficient determination for different DC standard resistors measurements based on Ⅴ-Ⅰ method

Current dependence and stability of the measured resistance value are very important for the accurate measurement of DC standard resistor. In this paper, the volt-ampere （V-I） measurement method has been applied to study the current depend-ence of four different types of standard resistors. Diverse values are obtained through the investigation of their stability at dif-ferent currents. Therefore, the current dependence coefficient （CDC） can be determined for each one of the studied resistors. Research shows CDC depends on the applied current value, the measurement time and the resistor type, as clearly demonstra-ted in this research.

Recursion-transform approach to compute the resistance of a resistor network with an arbitrary boundary

We consider a profound problem of two-point resistance in the resistor network with a null resistor edge and an arbitrary boundary,which has not been solved before because the Green＇s function technique and the Laplacian matrix approach are invalid in this case.Looking for the exact solutions of resistance is important but difficult in the case of the arbitrary boundary since the boundary is a wall or trap which affects the behavior of a finite network.In this paper,we give a general resistance formula that is composed of a single summation by using the recursion-transform method.Meanwhile,several interesting results are derived by the general formula.Further,the current distribution is given explicitly as a byproduct of the method.

A wideband metamaterial absorber based on a magnetic resonator loaded with lumped resistors

A wideband metamaterial absorber （MA） based on a magnetic resonator loaded with lumped resistors is presented. It is composed of a one-dimensional periodic array of double U-shaped structured magnetic resonators loaded with lumped resistors, a dielectric substrate, and a metal plate. We simulated, fabricated, measured, and analyzed the MA. The experimental results show that the reflectance （S11） is below -10 dB at normal incidence in the frequency range of 7.7 GHz 18 GHz, and the peak value is about -20 dB. Simulated power loss density distributions indicate that wideband absorption of the MA is mainly attributable to the lumped resistors in the magnetic resonator. Further investigations indicate that the distance between two unit cells along the magnetic field direction significantly influences the performance of the MA.

Thin Film Chip Resistors with High Resistance and Low Temperature Coefficient of Resistance

High resistance thin film chip resistors(0603 type) were studied,and the specifications are as follows:1 k? with tolerance about ±0.1% after laser trimming and temperature coefficient of resistance(TCR) less than ±15×10-6/℃.Cr-Si-Ta-Al films were prepared with Ar flow rate and sputtering power fixed at 20 standard-state cubic centimeter per minute(sccm) and 100 W,respectively.The experiment shows that the electrical properties of Cr-SiTa-Al deposition films can meet the specification requirements of 0603 ty...

Hybrid functional IrO_2-TiO_2 thin film resistor prepared by atomic layer deposition for thermal inkjet printheads

IrO2-TiO2 thin films were prepared by atomic layer deposition using Ir（EtCp）（COD） and titanium isopropoxide （TTIP）. The resistivity of IrO2-TiO2 thin films can be easily controlled from 1 500 to 356.7 μΩ·cm by the IrO2 intermixing ratio from 0.55 to 0.78 in the IrO2-TiO2 thin films. The low temperature coefficient of resistance（TCR） values can be obtained by adopting IrO2-TiO2 composite thin films. Moreover, the change in the resistivity of IrO2-TiO2 thin films was below 10% even after O2 annealing process at 600 ℃. The step stress test results show that IrO2-TiO2 films have better characteristics than conventional TaN08 heater resistor. Therefore, IrO2-TiO2 composite thin films can be used as a heater resistor material in thermal inkjet printhead.

Failure Behaviors and Mechanisms of High-Ohmic Resistors Protected by PF/EP Paint in Heat and Humid Environment

Phenolic formaldehyde(PF)and epoxy(EP)resins are commonly used in electronic packaging. In this paper, high-ohmic resistors(2.2 M?, ±0.5%,)with Cr-Si film were coated by PF/EP paint, and the resulting coated resistors were used for heat and humid(HH)experiments. The experimental results show that the corrosion of bandlike resistive films is selective and isotropic, and that the corrosion spots in resistive films all form along grooves and extend in the same direction. It is revealed that OH^- ions are generated due to the electrochemical reactions of resistive film in HH experiments, so a NaOH aqueous solution with pH about 10 was used to study the effects of absorbed water and OH^- ions on PF/EP polymer film. The results indicates that the color of some part on PF/EP polymer film changes due to corrosion, and that the corrosion part of the polymer film is easy to be peeled off. It can be inferred that OH^- ions generated in HH experiments may play a catalytic role in the chemical reactions between polymer film and the absorbed water, which accelerates the degradation of PF/EP protection film for a resistor.

Interaction of RuO₂and Lead-Silicate Glass in Thick-Film Resistors

Results of investigation of X-ray diffraction, infrared and optical spectra of powders of the ruthenium dioxide, lead-silicate glass as well as their mixture before and after sintering are reported. Sintering conditions typical for thick film resistors were used. Intensity of main lines of RuO2 in X-ray diffraction patterns of sintered mixtures decreases and they slightly shift towards small angles. No new reflexes appear in these patterns. Absorbance of RuO2 in the range of 2.5-100 μm is proportional to and featureless. Infrared spectrum of lead-silicate glass has absorption bands of [SiO4]4- tetrahedra and Pb-O bonds only. Optical spectrum of RuO2 has wide absorption bands at 950 and 370 nm. Spectra of the mixture of RuO2 and glass powders before and after sintering are different indicating that there is interaction between them during the sintering process. Concentration of free charge carriers estimated from the optical spectra is about 1021 cm-3.

Fabrication of integrated resistors in printed circuit boards

In order to utilize integrated passive technology in printed circuit boards （PCBs）, manufacturing processing for integrated resistors by lamination method was investigated. Integrated resistors fabricated from Ohmega technologies in the experiment were 1 408 pieces per panel with four different patterns A, B, C and D and four resistance values of 25, 50, 75 and 100 fL Six panel per batch and four batches were performed totally. The testing was done for 960 pieces of integrated resistors randomly selected with the same size. The value distribution ranges and the relative standard deviation （RSD） show that the scatter degree of the resistance decreases with the resistor size increasing and/or with the resistance increasing. Patterns D with resistance of 75 and 100% for four patterns have the resistance value variances less than 10%. Patterns C and D with resistance of 100 Ω have the manufacturing tolerance less than 10%. The process capabilities are from about 0.6 to 1.6 for the designed testing patterns, which shows that the integrated resistors fabricated have the potential to be used in multilayer PCBs in the future.

PF/EP/Nano-SiO_2 Composite Paint for Resistor

Phenolic resin(PF) and nano-SiO2 were used to improve the curing property and high humidity resistance of epoxy resin (EP) and methyl nadic anhydride (MNA) resistor paint, respectively. Hydrogen bonds, formed between phenolic resin and nano-SiO2 in alcohol, made nano-SiO2 disperse easily in EP/MNA paint through phenolic resin without being treated by supersonic vibration. When the mass ratio of PF to EP in paint is 3:7, the formed composite paint film can be cured in 2 min at 170 ℃ . When the mass ratio of nano-SiO2 to PF in paint is 3:100, the property of high humidity resistance of the composite paint is the best, meeting the requirement of varying ratio of resistance less than 0.1% after experiment on high humidity resistance. SEM analysis shows the surface of the composite paint film is smooth, glassy, tight and homogeneous, without acicular air holes.

Sensorless Control of Permanent Magnet Synchronous Motor Based on New Sliding Mode Observer with Single Resistor Current Reconstruction

To solve the chattering problem caused by discontinuous switching function in traditional sliding mode observer,a piecewise square root switching function with continuously varying characteristics is designed,and its stability is analyzed by using Lyapunov stability criterion.Secondly,according to the relationship among bus current,switching state and phase current,a single bus resistance sampling current reconstruction scheme without current sensors is adopted,which effectively reduces the cost of motor system.Finally,the feasibility and effectiveness of the proposed scheme are verified by simulation.

Negative-Resistance Characteristics Analysis of Poly-Silicon Resistors Formed on the Flow Sensor

In this paper we put forward a new concept about effective trapping center concentration N^e_T which is decreasing with the trapped charge Q corresponding to index movement,based on that,we discuss theⅠ-Ⅴand temperature characteristics of polysilicon resistors.The new concept presents ideal theoretical interpretion for the originally observed current-voltage negative-resistance characteristics of polysilicon resistors formed on the flow sensor,and also for poly-silicon film resistors. The final results agree well with the theoretical current-voltage characteristics.

Preparation of Lead-free Thick-film Resistor Pastes

The preparation of lead-free thick-film resistors are reported:using RuO 2 and ruthenates as conductive particles,glass powders composed of B 2 O 3,SiO 2,CaO and Al2 O 3 as insulating phase,adding organic matter which mainly consists of ethyl cellulose and terpineol to form printable pastes.Resistors were fabricated and sintered by conventional screen-printing on 96%Al 2 O 3 substrates,and then sintering in a belt furnace.X-ray diffraction(XRD) and electron scanning microscopy(SEM) have been used to characterize the conductive particles.The resistors exhibit good refiring stability and low temperature coefficient of resistance.Sheet resistance spans from about 80Ω/□ to 600Ω/□.The resistors prepared are qualified for common use.

Control of a fractional chaotic system based on a fractional-order resistor-capacitor filter

We present a new fractional-order resistor-capacitor controller and a novel control method based on the fractional- order controller to control an arbitrary three-dimensional fractional chaotic system. The proposed control method is simple, robust, and theoretically rigorous, and its anti-noise performance is satisfactory. Numerical simulations are given for several fractional chaotic systems to verify the effectiveness and the universality of the proposed control method.

Effects of thermal cycling on shear strength of soldered joints of laminar ceramic resistor

The shear strength of two joints with different compositions (Sn63Pb37 and SnAg3.0Cu0.5) was compared under thermal cycling conditions, and the effects of thermal cycling times on the two different joints were studied. Results indicate that the shear force of the joints soldered with lead-free solder is higher than that of the joints soldered with Sn-Pb solder. After 120 times thermal cycling, the shear force of both the two kinds of joints declines obviously. The fractures are located at the two interfaces which is between the resistor’s side pad and the ceramic, the other is between the resistor’s bottom pad and the solder. Analysis result on the fractures by means of SEM indicates that the micrographs of fractures change obviously and the grains grow coarser after thermal cycling.

Hybrid Operation of Fault Current Limiter and Thyristor Controlled Braking Resistor

The effectiveness of a combination of fault current limiter and thyristor controlled braking resistor on power system stability enhancement and damping turbine shaft torsional oscillations has been studied. If both devices operate at the same bus, the stabilization control scheme can be carried out continuously and with flexibility. As a result, the fault currents are limited, and the generator disturbances and the turbine shaft torsional oscillations are converged quickly. In this paper, the effectiveness of the combination of both devices has been demonstrated by considering 3LG （three-lines-to-ground） fault in a two-machine infinite bus system. Also, temperature rise effect of both devices with various resistance values and weights has been demonstrated. Simulation results indicate a significant power system stability enhancement and damping turbine shaft torsional oscillations as well as with allowable temperature rise.