Interleaved-Connected Split Planar Resonant Inductor Design in 1 kV SiC LLC Converters

Design method of split planar resonant inductor in 1 kV SiC logical link control(LLC)converter is proposed,which ensures the converter power density of 93.59 W/in^3 and peak efficiency of 95.73%.Split resonant inductor helps to provide symmetrical resonant current by symmetrical impedance,and improves the distortion of resonant current,which ensures the efficiency of the whole converter.An interleaved winding connecting scheme improves the power density of the planar magnets,which contributes to power density improvement.Design method and calculation process of such split planar resonant inductor are provided.To verify the feasibility of the proposed design method,a 1 kV/48 V 6.6 kW,210 k Hz SiC LLC prototype was built,and the experimental results are given.

Rugged Resonant Pole and Its Applications in Soft-Switching Converter

The soft switching operation principle and operation performance of rugged resonant pole (RRP) is given. The applications of RRP in soft switching DC DC converter and soft switching inverter are discussed in detail. RRP can constitute buck boost soft switching DC DC converter and isolated soft switching DC DC converter with the automatic limitation performance of output power. Partial series resonant DC DC converter with RRP can realize the zero voltage/zero current switching of power devices. RR...

Arm Voltage Balancing Control of Modular Multilevel Resonant Converter

Modular multilevel resonant converter is an promising candidate for high voltage applications since it has advantageous features,such as high efficiency,high voltage capability and easy fault-tolerant operation.However,the inequality of arm inductance in practice will lead to imbalance between the upper and lower arm voltages,which will induce large ripples in the circulating current and a dc bias on the voltage generated by modular circuits.To compensate for the voltage imbalance,effects of arm duty cycle changes on arm voltages are discussed.An arm voltage balancing control method is proposed:adjust arm duty cycle according to arm voltage deviation in every switching cycle.Simulation and experimental results are presented to validate the theoretical analysis and the proposed control method.

Performance Analysis of PI and Fuzzy Control for Modified LCC Resonant Converter Incorporating Boost Converter

In this paper, the modified LCC type of series-parallel Resonant Converter (RC) was designed and state-space modeling analysis was implemented. In this proposed converter, one leg of full bridge diode rectifier is replaced with Synchronous Rectifier (SR) switches. The proposed LCC converter is controlled using frequency modulation in the nominal state. During hold-up time, the SRswitches control is changed from in-phase to phase-shifted gate signal to obtain high DC voltage conversion ratio. Furthermore, the closed loop PI and fuzzy provide control on the output side without decreasing the switching frequency. The parameter such as conduction loss on primary and secondary side, switching loss, core and copper also reduced. Simultaneously, the efficiency is increased about 94.79 is realized by this scheme. The proposed converter with an input of 40 V is built to produce an output of 235 V with the help of ZVS boost converter [1] even under line and load disturbances. As a comparison, the closed loop fuzzy controller performance is feasible and less sensitive than PI controller.

Analysis and Design of a Kind of Improved Parallel Resonant Converters

Traditional transformer in high-voltage power supplies has many disadvantages such as high turn’s ratio, large volume and great design difficulties. Parallel resonant converters (PRCs) are widely used in high-voltage power supplies. A kind of high-voltage circuit topology can be formed by combining PRCs and voltage-doubler rectifier, which is called parallel resonant dual voltage converters (PRDVCs). In PRDVCs both voltage-doubler rectifier and transformer can boost voltage, which reduced turn’s ratio and volume of the transformer, making it easier to produce. Thus it not only realizes the high-voltage output, but also realizes the miniaturization of high-voltage power supply. Three modes of the converters were researched and simulated. Converting conditions of three modes were given. At last, PRDVCs was used to design a 5000V/50mA high-voltage power supply. The waveforms and results of the experiment were given, which validated the feasibility of the converters and its conversion efficiency might be improved to 93%.

Quasi-Square Wave Mode Phase-Shifted PWM LCC Resonant Converter for Regulated Power Supply

This paper presents an improved self sustained oscillating controller circuit using LCC components for improving the overall efficiency of the system. It has a micro controller based active controller, which controls the performance from no-load up to full-load. The steady state characteristics are developed and a design example is given in detail. The proposed controller allows zero current switching at any loading condition which results in a reasonable reduction of power loss during switching with a promising efficiency. Analytical and experimental results verify the achievement the design specifications.

Embedded Control of LCL Resonant Converter Analysis, Design, Simulation and Experimental Results

The Objective of this paper is to give more insight into CCM Operation of the LCL Converter to obtain op-timum design using state-space analysis and to verify the results using PSPICE Simulation for wide variation in loading conditions. LCL Resonant Full Bridge Converter (RFB) is a new, high performance DC-DC con-verter. High frequency dc-dc resonant converters are widely used in many space and radar power supplies owing to their small size and lightweight. The limitations of two element resonant topologies can be over-come by adding a third reactive element termed as modified series resonant converter (SRC). A three ele-ment resonant converter capable of driving voltage type load with load independent operation is presented. We have used embedded based triggering circuit and the embedded ‘C’ Program is checked in Keil Software and also triggering circuit is simulated in PSPICE Software. To compare the simulated results with hardware results and designed resonant converter is 200W and the switching frequency is 50 KHz.

Active Current Sharing of LCLC Resonant Converter with Switch-Controlled-Capacitor Technology

In this paper,an interleaved LCLC converter with enhancement-mode(E-mode)GaN devices is introduced to achieve the accurate current sharing performance for data center applications. Any tolerance in the resonant tank elements can lead to large load imbalance between any two different phases. Due to the steep gain curves of LCLC converters,conventional current sharing methods are not effective. In the proposed converter,the impedances of the resonant networks are matched by switching a capacitor,i.e.,switch controlled capacitor(SCC),in series with the resonant capacitor in one or some of the phases,which results in accurate load current sharing among the phases with an accuracy around 0.025%. The load share of a phase is sensed through the resonant current on it,and the control logic applied to such current sharing can be achieved. By this method,accurate current sharing is achieved for a wide input voltage range required for the hold-up time in data center applications. Interleaving is applied in the proposed multiphase LCLC converter,resulting in low current stress on the output capacitor and allowing ceramic capacitor implementation. Moreover,phase shedding accomplishes high light load efficiency. The performance of the proposed interleaved LCLC converter is verified by a two-phase 1 k W prototype with an input voltage ranging from 250 V to 400 V and a fixed 12 V output voltage.

A Resonant Dual Full-Bridge Class-E Bidirectional DC-DC Converter for Fuel Cell Electric Vehicle

The interests on energy storage schemes, bidirectional dc-dc converter and uninterruptible power supplies have been increasing nowadays as there wide researches are undertaken in the area of electric vehicles. A modified bi directional class-E resonant dc-dc converter is introduced here in this proposed topology for the application in electric vehicles. The advantages of soft switching techniques have been utilized for making analysis simple. The main advantage here in this system is that it can operate in a wide range of frequencies with minimal switching loss in transistors. This paper elaborates a detailed analysis on converter design and the same has been simulated and verified in Matlab/Simulink.

ANALYSIS OF ZERO-VOLTAGE QUASI-RESONANT BOOST DC-DC CONVERTER

The zero-voltage quasi-resonant boost switching DC-DC converter has been inves-tigated by using the time averaging equivalent circuit approach of periodically switching linearnetworks.The DC steady state and AC small signal characteristics of the converter are also given.

Fuzzy Logic Controlled Dual Active Bridge Series Resonant Converter for DC Smart Grid Application

Over the last few years, smart grids have become a topic of intensive research, development and deployment across the world. This is due to the fact that, through the smart grid, stable and reliable power systems can be achieved. This paper presents a fuzzy logic control for dual active bridge series resonant converters for DC smart grid application. The DC smart grid consists of wind turbine and photovoltaic generators, controllable and DC loads, and power converters. The proposed control method has been applied to the controllable load＇s and the grid side＇s dual active bridge series resonant converters for attaining control of the power system. It has been used for management of controllable load＇s state of charge, DC feeder＇s voltage stability during the loads and power variations from wind energy and photovoltaic generation and power flow management between the grid side and the DC smart grid. The effectiveness of the proposed DC smart grid operation has been verified by simulation results obtained by using MATLAB and PLECS cards.

A NOVEL PHASE SHIFTED ZERO VOLTAGE SWITCHED PWM CONVERTER

Phase shifted converter realizes zero voltage switching (ZVS) with the use of leakage inductance of the main transformer, however, the realization of ZVS for lagging bridge leg is difficult. This paper proposes a current enhanced principle, and based on the principle, a novel phase shifted converter is proposed, which adds an auxi liary resonant net to the conventional full bridge converter to help the lagging bridge leg to realize ZVS. The principle and the design of the novel converter are analyzed, and the simulational and experimental results verify the principle.

基于双向半桥LLC谐振变换器的退役电池组均衡方法

退役电池在储能应用过程中,由于其较大的不一致性问题会导致退役电池组出现过充或过放现象,从而限制电池组整体的容量甚至引起热失控,造成安全隐患。针对以上问题,设计一种基于双向半桥LLC谐振变换器的有源均衡电路。该均衡电路通过开关阵列与隔离型双向半桥LLC谐振变换器的相互配合,能够实现单体电池与电池组整体之间的能量传递,使退役电池组中各单体电池达到能量平衡。另外,为进一步提高均衡器的均衡速度及精度,提出一种联合电压与荷电状态(SOC)共同作为均衡变量的多状态均衡控制策略。依据电池组当前不同的能量状态,在电池组静置、充电及放电3种不同状态下,分别采用不同的均衡变量以及对应的均衡策略,从而实现电池组的快速均衡。最后,通过搭建小型的均衡实验样机对6节串联电池进行均衡实验,实验结果表明,所提均衡方法具有较快的均衡速度及较好的均衡效果。

应用于储能系统的CLLLC谐振变换器控制策略研究

动态性能和运行效率是CLLLC谐振变换器的重要性能指标。针对传统电压闭环控制加入电流驱动同步整流后系统动态性能进一步变差的问题,提出一种谐振电流内环的电压电流双闭环变频控制策略,并给出双环控制和同步整流的综合控制方法。首先根据变换器的增益特性,分析电感比和品质因数对增益曲线和效率的影响,并据此进行谐振参数设计;其次根据不同谐振状态下的谐振电流特性实现同步整流;最后引入谐振电流内环控制,实现双环控制和同步整流的综合控制。仿真结果表明,所提综合控制策略能够产生精确的同步整流驱动信号,相比于传统电压闭环控制,能够显著改善变换器对负载扰动和电压扰动的动态性能。

三相CLLC谐振变换器磁集成平面变压器设计与优化

三相CLLC谐振变换器凭借其高效率、大容量、低器件应力等优势而受到广泛关注。然而,多相结构的磁性元件数量多、体积大,是制约功率变换器尺寸的主要因素。随着宽禁带(WBG)半导体器件的出现,功率变换器的开关频率显著提高,这也为印制电路板(PCB)绕组的使用提供了有利条件。与传统绕线式绕组相比,PCB绕组的扁平特性更适用于平面磁性元件。此外,由于高频带来的低电感需求也使得基于PCB绕组的平面磁性元件更有利于实现集成。该文提出一种新型的基于PCB绕组的电感和变压器的集成结构,详细分析磁心结构的磁路模型,并给出集成磁件的优化设计方法,最后通过搭建一台基于SiC器件的800 V/10 kW的实验样机进行验证。实验结果表明,该集成方案可有效减小变换器的体积和损耗,具有高功率密度和高效率。

宽增益高效率级联式四开关Buck-Boost LLC变换器

为了解决变频控制的桥臂共用型四开关Buck-BoostLLC级联变换器磁性元件设计和优化困难的问题,提出一种二次侧为特殊全桥整流结构的级联式四开关Buck-Boost LLC变换器。通过控制二次侧开关管的交叠导通时间以拓宽变换器的电压增益。该变换器可根据不同的输入电压范围工作在交叠模式和整流模式;在不改变变换器参数的条件下将增益显著提高,能够适应更宽范围的输入电压,同时保持了变换器较高的工作效率。在两种工作模式的基础上,采用移相控制使变换器所有开关管实现零电压导通(ZVS),二极管实现零电流关断(ZCS)。结合状态平面轨迹分析法,对定频控制的级联式四开关Buck-Boost LLC变换器进行模态分析,并推导两种工作模式下的输入-输出表达式和开关管的软开关实现条件。最后,通过研制一台70~280 V输入、240 W/28 V输出的实验样机,验证了理论分析的正确性。

变化负载下全桥LLC谐振变换器参数优化设计

LLC谐振变换器在软开关特性方面有一定的局限性。针对可变负载条件下LLC谐振变换器软开关特性不稳定的问题,本文结合ZVS/ZCS边界推导了软开关约束条件,提出一套基于全桥LLC谐振变换器变化负载下参数优化设计方法,以提高系统的稳定性和效率。方案不仅考虑谐振电感、电容和变压器的参数优化,还充分考虑负载变化对软开关行为的影响。文中介绍了全桥LLC谐振变换器的工作原理,并对电压增益与谐振网络阻抗特性进行较为细致的分析。根据上述设计方案搭建了一台500 W的车载充电机试验样机,在实验室条件下对样机进行测试,结果表明试验样机整机在参数优化后效率有所提升,最高效率可达96.36%。

采用金豺优化的LLC谐振变换器自抗扰稳压控制

为解决LLC谐振变换器采用传统PID控制时抑制负载冲击能力差的问题,提出采用金豺优化算法(golden jackal optimization,GJO)的改进线性自抗扰控制方法。该方法基于状态空间表达式,结合降阶模型中的参数信息,改进扩张状态观测器的系数矩阵。利用频域拟合的方法获得线性自抗扰控制器参数初值,避免了繁复的人工调参过程。使用GJO算法对线性自抗扰控制器参数寻优,进一步改善控制器性能。实验结果表明,相较于PSO-PID控制器,GJO-MLADRC控制器有效提高了LLC谐振变换器在系统扰动较大的情况下的动态性能,在负载突增、突降2种工况下,调节时间分别缩短了1.5、1.0 ms,输出电压最大波动量分别减小0.10、0.05 V,改进后的LADRC控制策略有效地抑制了恒压模式下负载波动对输出电压的扰动。

宽范围输入三电平半桥LLC变换器混合控制

针对传统变频(PFM)控制的LLC谐振变换器在宽电压输入条件下效率低的问题,提出一种三电平半桥LLC谐振变换器的变频-移相(PFM-PS)混合控制策略。首先,分析三电平半桥LLC谐振变换器的工作模态,建立其等效模型,获得了移相控制和变频控制下的电压增益曲线。其次,分析了变频控制的工作区间与软开关特性,推导得到了移相控制下实现软开关的最小占空比。通过混合控制策略,在升压时采用变频控制和在降压时采用移相控制,相较于全变频控制和全移相控制,混合控制可在较小频率变化范围内对电压进行升降压,在全增益范围内实现软开关,获得较宽的电压增益范围,提升了变换器的效率。最后,通过仿真和输入500~800 V/4.5 kW实验样机验证了所提出混合控制策略的有效性。

限制调频范围的不对称多模式宽输出LLC变换器

频率控制的传统LLC谐振变换器往往受限于开关频率的有效调节范围,难以实现宽输出电压范围,为此,研究了一种限制调频范围的不对称多模式宽输出LLC谐振变换器。采用双谐振腔且对应两变压器变比不同的不对称结构,能够根据原边开关组合的不同,使得双谐振腔分别工作在单半桥、双半桥和半桥+全桥3种不同的模式,从而获得3种不同的电压增益,并且保证每种模式之间归一化增益调节范围不超过1.5,可以在窄开关频率范围内实现宽输出电压范围。建立300 W的实验样机,验证了所提变换器可实现1~3倍的宽输出电压范围,并且实现了原边开关管的零电压开通和副边二极管的零电流关断,具有良好的软开关性能,验证了变换器的可行性。