Influence of pressure disturbance wave on dynamic response characteristics of liquid film seal for multiphase pump

Slug flow or high GVF(Gas Volume Fraction)conditions can cause pressure disturbance waves and alternating loads at the boundary of mechanical seals for multiphase pumps,endangering the safety of multiphase pump units.The mechanical seal model is simplified by using periodic boundary conditions and numerical calculations are carried out based on the Zwart-Gerber-Belamri cavitation model.UDF(User Define Function)programs such as structural dynamics equations,alternating load equations,and pressure disturbance equations are embedded in numerical calculations,and the dynamic response characteristics of mechanical seal are studied using layered dynamic mesh technology.The results show that when the pressure disturbance occurs at the inlet,as the amplitude and period of the disturbance increase,the film thickness gradually decreases.And the fundamental reason for the hysteresis of the film thickness change is that the pressure in the high-pressure area cannot be restored in a timely manner.The maximum value of leakage and the minimum value of axial velocity are independent of the disturbance period and determined by the disturbance amplitude.The mutual interference between enhanced waves does not have a significant impact on the film thickness,while the front wave in the attenuated wave has a promoting effect on the subsequent film thickness changes,and the fluctuation of the liquid film cavitation rate and axial velocity under the attenuated wave condition deviates from the initial values.Compared with pressure disturbance conditions,alternating load conditions have a more significant impact on film thickness and leakage.During actual operation,it is necessary to avoid alternating load conditions in multiphase pump mechanical seals.

Research on vibration response characteristics and evolution law of finishing rolling in hot strip mills

In this study,a comprehensive rolling mill vibration test program was designed,including specific test conditions and a test system.The analysis of measured signals reveals the vibration response characteristics and their evolution at different gauge points in the finishing mill.This is particularly evident during abnormal rolling,where the signals highlight the characteristics of abnormal responses and vibration intensities.Abnormal vibrations during the rolling process mainly occur when the strip thickness is less than 2.5 mm,and at the rolling speed-up stage,the strong abnormal vibration occurs at each measuring point on the F2 transmission side.The maximum vibration intensity of the backup roll’s bearing seat is 17 mm/s.As the rolling progresses,the stress on the bolts changes.The strip thickness is negatively correlated with the peak values of bite and tail-flick impacts.The vibration characteristics vary with the strip thickness and the process state.

Dynamic response law about gravity retaining wall to seismic characteristics and earth fill properties

In order to find the dynamic response laws of retaining walls affected by certain earthquake loads,the influence of the seismic wave characteristics and sub-grade fill parameters(including the foundation surface slope) were focused on,and a series of tests were performed.The results show that the maximum stress of the retaining wall decreases as internal friction angle,foundation slope,filled soil cohesion and the biggest dynamic elastic modulus increase,while it increases with the seismic frequency and seismic input peak dropping.The addition value of dynamics earth pressure increases when seismic frequency and seismic input peak are reduced,while it decreases when the filled soil cohesion and internal friction angle rise.Meanwhile,dynamic elastic modulus and foundation slope have no obvious influences on addition value of dynamics earth pressure.The slope will be instable if the seismic input peak exceeds 0.5g and be disruptive if seismic frequency is larger than 2.5 Hz.The mid-lower parts of retaining walls are in most heavy and obvious response to these factors,which reveals the mechanism of "belly burst" in retaining wall that appears commonly in practical projects.

Analysis and application of the response characteristics of DLL and LWD resistivity in horizontal well

There exist different response characteristics in the resistivity measurements of dual laterolog （DLL） and logging while drilling （LWD） electromagnetic wave propagation logging in highly deviated and horizontal wells due to the difference in their measuring principles. In this study, we first use the integral equation method simulated the response characteristics of LWD resistivity and use the three dimensional finite element method （3D-FEM） simulated the response characteristics of DLL resistivity in horizontal wells, and then analyzed the response differences between the DLL and LWD resistivity. The comparative analysis indicated that the response differences may be caused by different factors such as differences in the angle of instrument inclination, anisotropy, formation interface, and mud intrusion. In the interface, the curves of the LWD resistivity become sharp with increases in the deviation while those of the DLL resistivity gradually become smooth. Both curves are affected by the anisotropy although the effect on DLL resistivity is lower than the LWD resistivity. These differences aid in providing a reasonable explanation in the horizontal well. However, this can also simultaneously lead to false results. At the end of the study, we explain the effects of the differences in the interpretation of the horizontal well based on the results and actual data analysis.

Shear mechanical properties and fracturing responses of layered rough jointed rock-like materials

This study aims to investigate mechanical properties and failure mechanisms of layered rock with rough joint surfaces under direct shear loading.Cubic layered samples with dimensions of 100 mm×100 mm×100 mm were casted using rock-like materials,with anisotropic angle(α)and joint roughness coefficient(JRC)ranging from 15°to 75°and 2-20,respectively.The direct shear tests were conducted under the application of initial normal stress(σ_(n)) ranging from 1-4 MPa.The test results indicate significant differences in mechanical properties,acoustic emission(AE)responses,maximum principal strain fields,and ultimate failure modes of layered samples under different test conditions.The peak stress increases with the increasingαand achieves a maximum value atα=60°or 75°.As σ_(n) increases,the peak stress shows an increasing trend,with correlation coefficients R² ranging from 0.918 to 0.995 for the linear least squares fitting.As JRC increases from 2-4 to 18-20,the cohesion increases by 86.32%whenα=15°,while the cohesion decreases by 27.93%whenα=75°.The differences in roughness characteristics of shear failure surface induced byαresult in anisotropic post-peak AE responses,which is characterized by active AE signals whenαis small and quiet AE signals for a largeα.For a given JRC=6-8 andσ_(n)=1 MPa,asαincreases,the accumulative AE counts increase by 224.31%(αincreased from 15°to 60°),and then decrease by 14.68%(αincreased from 60°to 75°).The shear failure surface is formed along the weak interlayer whenα=15°and penetrates the layered matrix whenα=60°.Whenα=15°,as σ_(n) increases,the adjacent weak interlayer induces a change in the direction of tensile cracks propagation,resulting in a stepped pattern of cracks distribution.The increase in JRC intensifies roughness characteristics of shear failure surface for a smallα,however,it is not pronounced for a largeα.The findings will contribute to a better understanding of the mechanical responses and failure mechanisms of the layered rocks subjected to shear loads.

Vegetation characteristics and soil properties of artificially remediated grasslands:The case study of the Shimenhe mining area in Qilian Mountains,northwest China

The mining of limestone mines plays a crucial role in societal and economic advancement.However,mining activities have led to destructive variations in grassland ecology and soil,causing numerous environmental problems,and effective artificial restoration measures have been used to restore grasslands in the Shimenhe mining areas to different degrees.In this study,we investigated,examined and analyzed plant community structure and its correlation with soil properties across varying degrees of alpine grassland restoration in Qilian Mountains Shimenhe restoration mines using the sample method,and studied the changes in species diversity using five diversity indexes(Simpson index,Shannon index,Margalef index,Dominance index and Evenness index).This study showed that the plant community characteristics with high recovered degree(HRD)> middle recovered degree(MRD)> low recovered degree(LRD)> very low recovered degree(VLRD),11 plant genera comprising 11 species across 10 families were identified.Dominant families with robust ecological adaptability included Leguminosae,Rosaceae,Gramineae,Asteraceae,and Salicaceae.The highest Simpson,Shannon,Margalef and Evenness index of HRD grassland community species were 0.82,1.96,1.66 and 0.89,respectively.The highest Dominance index of VLRD grassland community species was 0.34,which required several restoration methods such as spraying and mulching.Soil pH and EC tended to decrease with increasing restoration,SOC,SMC,TP,AP,NH4-N,TN,AN and NO3-N tended to increase and the content of soil environmental factors contributed to vegetation growth across various restoration levels the mine grassland.In conclusion,our study indicated that the community structure gradually diversified and soil properties changed positively with the increase of restoration degrees in the Qilian Mountains Shimenhe mine,and the best results of HRD restoration were obtained.This study provides the theoretical basis for the restoration and conservation of grasslands in mining areas by demonstrating examined the correlation between plant characteristics and soil properties in restored grasslands in alpine mining areas.

Landslide Developmental Characteristics and Response to Climate Change since the Last Glacial in the Upper Reaches of the Yellow River, NE Tibetan Plateau

The upper reaches of the Yellow River in northeastern Tibetan Plateau are geohazards areas.The evolution of the Yellow River,chronology of some landslides,and spatiotemporal distribution characteristics of super large scale and giant landslides within the region are summarized using paleoclimate evidence,and the relationship between the intensive landslide period and climatic changes since the Last Glacial period is analyzed.It is concluded that （1） Super large scale and giant landslides are distributed widely within the region,particularly in the Qunke-Jianzha basin.（2） The chronological sequence of landslides is established by dating the slip zones of landslides and analyzing the relations between landslides and their overlying or underlying loess formations.Five landslide development periods are determined：53-49 ka BP,33-24 ka BP,10-8 ka BP,5-3.5 ka BP,and the present.（3） These correspond closely to warm and wet periods during the last 100,000 years,i.e.,two weak paleosol development stages of Malan loess deposited during the last Glacial period in the Chinese loess Plateau,L1-4 and L1-2 that belong to the marine oxygen isotope stage 3,the last deglaeial period,the Holocene Optimum,and the modern global warming period.（4） Landslide triggers may be closely linked to warm and wet periods related to rapid climatic transitions.

Hepatic Histopathological Characteristics and Antioxidant Response of Phytoplanktivorous Silver Carp Intraperitoneally Injected with Extracted Microcystins

Objective To investigate the hispathological characteristics and antioxidant responses in liver of silver carp after intraperitoneal administration of microcystins （MCs） for further understanding hepatic intoxication and antioxidation mechanism in fish. Methods Phytoplanktivorous silver carp was injected intraperitoneally （i.p.） with extracted hepatotoxic microcystins （mainly MC-RR and -LR） at a dose of 1000 μg MC-LReq./kg body weight, and liver histopathological changes and antioxidant responses were studied at 1, 3, 12, 24, and 48 h, respectively, after injection. Results The damage to liver structure and the activities of hepatic antioxidant enzymes including catalase （CAT）, superoxide dismutase （SOD）, and glutathione peroxide （GPX） were increased in a time-dependent manner. Conclusion In terms of clinical and histological signs of intoxication and LD50 （i.p.） dose of MC-LR, silver carp appears rather resistant to MCs exposure than other fishes. Also the significantly increased SOD activity in the liver of silver carp suggests a higher degree of response to MCs exposure than CAT and GPX.

DYNAMIC RESPONSE OF ROLLER GEAR INDEXING CAM SYSTEM CONSIDERING CLEARANCE AND MOTOR CHARACTERISTIC

The dynamic responses of roller gear indexing cam mechanism are investigated .With applying Lagarange equation and Gear method,motion equations of this mechanism including clearance,motor characteristic,torsion flexibility are developed and solved.The results show that clearance affects primarily the response on turret,and has little effects on the responses on rotary table.At the same time,the velocity fluctuation of motor shaft is not serious for the existence of inertia of reducer,and the high frequency of velocity fluctuation of camshaft is related with the torsion stiffness of shaft and the clearance between pairs.

Efficient computation for dynamic responses of systems with time-varying characteristics

Based on Neumman series and epsilon-algorithm, an efficient computation for dynamic responses of systems with arbitrary time-varying characteristics is investigated. Avoiding the calculation for the inverses of the equivalent stiffness matrices in each time step, the computation effort of the proposed method is reduced compared with the full analysis of Newmark method. The validity and applications of the proposed method are illustrated by a 4-DOF spring-mass system with periodical time-varying stiffness properties and a truss structure with arbitrary time-varying lumped mass. It shows that good approximate results can be obtained by the proposed method compared with the responses obtained by the full analysis of Newmark method.

Laboratory-scale investigation of response characteristics of liquid-filled rock joints with different joint inclinations under dynamic loading

In underground rock engineering,water-bearing faults may be subjected to dynamic loading,resulting in the coupling of hydraulic and dynamic hazards.Understanding the interaction mechanism between the stress waves induced by dynamic loadings and liquid-filled rock joints is therefore crucial.In this study,an auxiliary device for simulating the liquid-filled layer was developed to analyze the dynamic response characteristics of liquid-filled rock joints in laboratory.Granite and polymethyl methacrylate(PMMA)specimens were chosen for testing,and high-amplitude shock waves induced by a split Hopkinson pressure bar(SHPB)were used to produce dynamic loadings.Impact loading tests were conducted on liquid-filled rock joints with different joint inclinations.The energy propagation coefficient and peak liquid pressure were proposed to investigate the energy propagation and attenuation of waves propagating across the joints,as well as the dynamic response characteristics of the liquid in the liquid-filled rock joints.For the inclination angle range considered herein,the experimental results showed that the energy propagation coefficient gently diminished with increasing joint inclination,and smaller coefficient values were obtained for granite specimens compared with PMMA specimens.The peak liquid pressure exhibited a gradually decreasing trend with increasing joint inclination,and the peak pressure for granite specimens was slightly higher than that for PMMA specimens.Overall,this paper may provide a considerably better method for studying liquid-filled rock joints at the laboratory scale,and serves as a guide for interpreting the underlying mechanisms for interactions between stress waves and liquid-filled rock joints.

Experimental study of the dynamic mechanical responses and failure characteristics of coal under true triaxial confinements

Investigations on the dynamic mechanical properties and failure mechanisms of coal under in-situ stress is essential for the prevention of dynamic disasters in deep coal mines.Thus,a modified true triaxial Hopkinson bar was employed to explore the dynamic mechanical behaviors of coal at different confining pressures(0–20 MPa)and strain rates(40–220 s^(-1)).The results show that the dynamic peak stress is positively correlated with lateral static pre-stressσy andσz,but negatively correlated with axial static prestressσx.At approximate strain rates,increasing the lateral static pre-stress facilitates increasing the dynamic peak stress,but the minimum lateral static pre-stress is the primary factor limiting a significant increase in dynamic peak stress of coal.Furthermore,the dynamic differential stress is linearly related to the logarithm of strain rate,and the peak strain varies linearly with strain rate.However,there is no significant correlation between confining pressure and peak strain.Moreover,X-ray CT images and photographic fracture observations of coal samples show the failure patterns under uniaxial and triaxial conditions are splitting failure and shear failure,respectively.The device provides a viable approach for fully comprehending the dynamic mechanical behaviors of rock-like material in complex stress conditions.

Test of frequency characteristic for well and itsresponse to seismic waves

The permeation parameters have been calculated by forefathers on the basis of permeation theory by means of the Slug test (Yin, Zheng, 1992) and the restoration curves of well level. We are interested in oscillation of the well level when we make Slug test. Both the permeation parameters and frequency parameters, i.e., natural period and damping coefficients of well aquifer, have been calculated on the basis of vibration theory by means of the oscillation curves. Not only this has given a new method, but also the different response of well level to seismic waves has been explained by it in theory.

Experimental study on seismic response and progressive failure characteristics of bedding rock slopes

Bedding rock slopes are common geological features in nature that are prone to failure under strong earthquakes. Their failures induce catastrophic landslides and form barrier lakes, posing severe threats to people’s lives and property. Based on the similarity criteria, a bedding rock slope model with a length of3 m, a width of 0.8 m, and a height of 1.6 m was constructed to facilitate large-scale shaking table tests.The results showed that with the increase of vibration time, the natural frequency of the model slope decreased, but the damping ratio increased. Damage to the rock mass structure altered the dynamic characteristics of the slope;therefore, amplification of the acceleration was found to be nonlinear and uneven. Furthermore, the acceleration was amplified nonlinearly with the increase of slope elevation along the slope surface and the vertical section, and the maximum acceleration amplification factor(AAF) occurred at the slope crest. Before visible deformation, the AAF increased with increasing shaking intensity;however, it decreased with increasing shaking intensity after obvious deformation. The slope was likely to slide along the bedding planes at a shallow depth below the slope surface. The upper part of the slope mainly experienced a tensile-shear effect, whereas the lower part suffered a compressive-shear force. The progressive failure process of the model slope can be divided into four stages, and the dislocated rock mass can be summarized into three zones. The testing data provide a good explanation of the dynamic behavior of the rock slope when subjected to an earthquake and may serve as a helpful reference in implementing antiseismic measures for earthquake-induced landslides.

Morphological Characteristics of Cambodia Mekong Delta and Tonle Sap Lake and Its Response to River-Lake Water Exchange Pattern

Tonle Sap Lake is the largest river-connected lake, buffer area and ecological zone of Mekong River, which plays a huge role in dispelling flood peak and compensating water, and the conservation of biological diversity. The river-lake relationship between Mekong River and Tonle Sap Lake is unique and has always been a major focus in the international community. The land terrain and under-water topography were used to analyze the morphological characteristics of Cambodia Mekong Delta and Tonle Sap Lake. Long series of hydrological data of river-lake controlling stations were used to analyze the water level variation characteristics and water volume exchange pattern between Mekong River and Tonle Sap Lake, and the response relationship to river-lake morphological characteristics were also researched. The results show that: Cambodia Mekong Delta and Tonle Sap Lake Area is low-lying and flat with gentle channel gradient and water surface gradient, making the relationship between water level and area (or volume) smooth. The channel storage capacity of Mekong River and Tonle Sap River is not enough compared to the inflow, so vast flooding plain is extremely prone to be inundated, making the flood relationships between the left and right banks become very complicated. Tonle Sap Lake is a seasonal freshwater lake with water flowing in and flowing out, and the timing and intensity of water exchange with Mekong River are closely related to the water flow resistance at the exit section of Tonle Sap Lake and the cross-sectional area of Tonle Sap River, which can be reflected by the river-lake water level difference and the water level of Tonle Sap River. Affected by the river-lake morphological characteristics, the water exchange intensity between Mekong River and Tonle Sap Lake is great. Tonle Sap Lake not only stores 14.4% of flood volume (39.7 billion m3) from the Mekong River every year, but also supplies 29.7% of dry water (69.4 billion m3) to the Mekong River. Influenced by the adjustment of the floodplain, the water level fluctuation of Mekong River and Tonle Sap Lake is slow, and the rising and droop rates of water level are positively correlated with the floodplain storage area. The research results will help to understand the relationship mechanism between Mekong River and Tonle Sap Lake and provide a scientific basis for the comprehensive governance of Cambodia Mekong Delta and Tonle Sap Lake Area.

Stress response characteristics of BFRP anchors on loess mudstone slope under rainfall conditions

To investigate the stress response characteristics and shear stress transfer mechanism of BFRP(basalt fiber reinforced plastics)anchors under rainfall conditions and to explore the reinforcement effect of BFRP anchors,a comparative indoor physical model test was conducted in this study using loess mudstone slope as a typical case,and multi-attribute response data,such as slope displacement,BFRP anchor strain and axial force,were obtained.Based on the variation law of slope displacement,it can be concluded that the deformation displacement of the slope on the side reinforced by BFRP anchors is smaller than that of slopes reinforced with steel anchors;the bearing capacity of BFRP anchor is given priority in time,and the anchoring effect of BFRP anchor at the top of the slope is given priority,and the axial force value of anchor is characterized by a surface amplification effect in space;the axial force is higher around the anchor head and tends to decay as a negative exponential function as the anchor extends in the direction of the interior of the slope;the shear stress of BFRP anchor and anchorage body are unevenly distributed along the axial direction,with the maximum value occurring in the free section near the slope surface and decreases as the BFRP anchor extends towards the interior of the slope.These results can provide a theoretical basis for the optimal design of BFRP anchors.

Flow-rate Characteristics Measurement of Regulators Based on the Pressure Response in an Isothermal Tank

Regulators are important components in pneumatic system, and their flow-rate characteristics are the key parameters for designers. According to the correlatively international standard and national standard of China, which describe the flow-rate characteristics measurement method of pneumatic regulators, the pressure and the flow are measured point by point, and then the flow-rate characteristics curve is plotted point to point. This method has some disadvantages, such as equipment complexity, much air consumption, and low efficiency. To settle the problems presented above, this paper puts forward a new high efficient and energy saving flow-rate characteristics measurement method of regulators, which is based on the pressure response when charging and discharging to an isothermal tank without any flow meters. The measurement principle, the system and the steps are introduced. And the tracking differentiator is used for the data processing of the pressure difference. Two typical kinds of regulators were experimentally investigated, and their flow-rate characteristics curves were obtained with the new and the conventional method, respectively. Comparatively, it＇s proved that this new method is feasible because it is not only able to meet the demand of the measurement precision, but also to save energy and improve efficiency. Compared to the conventional method, the new method takes only about 1/10 amount of time and consumes about only 1/30 amount of air. Hopefully it will be able to serve as an international standard of flow-rate characteristics measurement method of regulators.

Response characteristics of sonar receiver under intense sound pulse

For anti-jamming and anti-countermeasure techniques of the sonar receiver, the response characteristics of the automatic gain control （AGC） circuit and the survivability of the prime circuit under strong interference are analyzed by simulations and experiments. An AGC simulation model based on the voltage control amplifier VCA810 prototype is proposed. Then static and dynamic simulations are realized with single frequency signal and linear frequency modulated （LFM） signal commonly used in the active sonar. Based on intense sound pulse （ISP） interference experiments, the real-time response characteristics of each module of the receiver are studied to verify the correctness of the model as well as the simulation results. Simulation and experiment results show that, under 252 dB/20 μs ISP interference, the specific sonar receiver will produce sustained cut top oscillation above 30 ms, which may affect the receiver and block the regular sonar signal.

Quench characteristics and mechanical responses during quench propagation in rare earth barium copper oxide pancake coils

Quench and mechanical behaviors are critical issues in high temperature superconducting(HTS)coils.In this paper,the quench characteristics in the rare earth barium copper oxide(REBCO)pancake coil at 4.2K are analyzed,and a two-dimensional(2D)axisymmetric electro-magneto-thermal model is presented.The effects of the constituent materials,background field,and coil size are analyzed.An elastoplastic mechanical model is used to study the corresponding mechanical responses during the quench propagation.The variations of the temperature and strain in superconducting layers are compared.The results indicate that the radial strain evolutions can reflect the transverse quench propagation and the tensile hoop and radial stresses in superconducting layers increase with the quench propagation.The possible damages are discussed with the consideration of the effects of the background field and coil size.It is concluded that the high background field significantly increases the maximum tensile hoop and radial stresses in quenching coils and local damage may be caused.

Research on coupled thermo-hydro-mechanical dynamic response characteristics of saturated porous deep-sea sediments under vibration of mining vehicle

The excessive deformation of deep-sea sediments caused by the vibration of the mining machine will adversely affect the efficiency and safety of mining.Combined with the deep-sea environment,the coupled thermo-hydro-mechanical problem for saturated porous deep-sea sediments subject to the vibration of the mining vehicle is investigated.Based on the Green-Lindsay(G-L)generalized thermoelastic theory and Darcy’s law,the model of thermo-hydro-mechanical dynamic responses for saturated porous deep-sea sediments under the vibration of the mining vehicle is established.We obtain the analytical solutions of non-dimensional vertical displacement,excess pore water pressure,vertical stress,temperature,and change in the volume fraction field with the normal mode analysis method,and depict them graphically.The normal mode analysis method uses the canonical coordinate transformation to solve the equation,which can quickly decouple the equation by ignoring the modal coupling effect on the basis of the canonical mode.The results indicate that the vibration frequency has obvious influence on the vertical displacement,excess pore water pressure,vertical stress,and change in volume fraction field.The loading amplitude has a great effect on the physical quantities in the foundation,and the changes of the physical quantities increase with the increase in loading amplitude.