RELATIONSHIP BETWEEN RETAINED AUSTENITE AND STRAIN FOR Si-Mn TRIP STEEL

The equation which reflects the relationship between the retained austenite and strain has been proposed and clear TRIP can be obtained while the S value (An index of retained austenite stability) is less than 6.5 for Silicon-Manganese TRIP steel

Correlation of isothermal bainite transformation and austenite stability in quenching and partitioning steels

The possible decomposition of metastable austenite during the partitioning process in the high end quenching and partitioning （Q＆P） steels is somewhat neglected by most researchers. The effects of primary martensite and alloying elements including manganese, cobalt and aluminum on the isothermal decomposition of austenite during typical Q＆P process were studied by dilatometry. The transformation kinetics was studied systematically and resulting microstruc tures were discussed in details. The results suggested that the primary martensite decreased the incubation period of isothermal decomposition by accelerating the nucleation process owing to dislocations especially on phase and grain boundaries. This effect can be eliminated by a flash heating which recovered dislocations. Co addition significantly promoted the bainite transformation during partitioning while A1 and Mn suppressed the isothermal bainite transformation. The bainite transformation played an important role in carbon distribution during partitioning, and hence the amount and stability of austenite upon final quenching. The bainite transformation during partitioning is an important factor in optimizing the microstructure in Q＆P steels.

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships（ORs）between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction（SAED）as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_（bcc）.A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.

A thermodynamic model on predicting density of medium-Mn steels with experimental verification

A new model on predicting the density of hot-rolled multi-phased medium-Mn steel has been presen ted on the basis of thermodynamic calculations. This is an integrated model, which includes one for calculating the retained austenite （RA） fraction and the other for volume expansion during the aus tenite-to martensite transformation, because both of them are key parameters for calculating the den- sity of steel at ambient temperature. The existing empirical equations for calculating Mx temperature and lattice constants of both martensite and austenite have been all rcassessed by the XRD measure ments on the microstructures of seven hot-rolled medium-Mn steels. Finally, the densities ot seven steels were calculated merely from compositions and compared with the measured ones. The differ ence between them is no more than 1 %, suggesting that the presented model should be of good value in designing the low density steels.

Microstructure evolution and mechanical properties influenced by austenitizing temperature in aluminum-alloyed TRIP-aided steel

The Fe-0.21C 2.2Mn 0.49Si-1.77A1 transformation induced plasticity （TRIP） aided steel was heat trea- ted at various austenitizing temperatures under both TRiP-aided polygonal ferrite type （TPF） and an- nealed martensite matrix （TAM） processes. The microstructure evolution and their effects on mechanical properties were systematically investigated through the microstructure observation and dilatometric analysis. The microstructure homogeneity is improved in TPF steel heated at a high temperature due to the reduced banded martensite and the increased bainite. Compared with the mechanical properties of the TPF steels, the yield strength and elongation of the TAM steels are much higher, while the tensile strength is lower than that of TPF steels. The stability of intercritical austenite is affected by the heating tempera- ture, and thus the following phase transformation influences the mechanical properties, such as the bain- ite transformation and the precipitation of polygonal ferrite. Obvious dynamic bainite transformation occurs at TAM850, TAM900 and TAM950, More proportion of polygonal ferrite is found in the sample heated at 950 ℃. The bainite transformation beginning at a higher temperature results in the wider bainitic ferrite laths. The more proportion of polygonal ferrite and wide bainitic ferrite laths commonly contribute to the lower strength and better elongation. The uniform microstructure with lath-like morphology and retained austenite with high average carbon content ensures a good mechanical property in TAM850 with the product of strength and elongation of about 28 GPa ·%,