Sulfolane‑Based Flame‑Retardant Electrolyte for High‑Voltage Sodium‑Ion Batteries

Sodium-ion batteries hold great promise as next-generation energy storage systems.However,the high instability of the electrode/electrolyte interphase during cycling has seriously hindered the development of SIBs.In particular,an unstable cathode–electrolyte interphase(CEI)leads to successive electrolyte side reactions,transition metal leaching and rapid capacity decay,which tends to be exacerbated under high-voltage conditions.Therefore,constructing dense and stable CEIs are crucial for high-performance SIBs.This work reports localized high-concentration electrolyte by incorporating a highly oxidation-resistant sulfolane solvent with non-solvent diluent 1H,1H,5H-octafluoropentyl-1,1,2,2-tetrafluoroethyl ether,which exhibited excellent oxidative stability and was able to form thin,dense and homogeneous CEI.The excellent CEI enabled the O3-type layered oxide cathode NaNi_(1/3)Mn_(1/3)Fe_(1/3)O_(2)(NaNMF)to achieve stable cycling,with a capacity retention of 79.48%after 300 cycles at 1 C and 81.15%after 400 cycles at 2 C with a high charging voltage of 4.2 V.In addition,its nonflammable nature enhances the safety of SIBs.This work provides a viable pathway for the application of sulfolane-based electrolytes on SIBs and the design of next-generation high-voltage electrolytes.

Preparation of Polyurea Elastomer with Flame Retardant, Insulation and Thermal Conductivity Properties

By using 6,6-((sulfonylbis(4,1-phenylene)bis(azanediyl))bis(thiophen-2-ylm-ethylene))bis6H-di-benzo[c,e][1,2]oxaphosphinine 6-oxide(DOPO-N)as phosphorus-nitrogen flame retardant,the polyurea(PUA)with flame retardant properties(PUA/DOPO-N)was prepared.In addition,organically modified montmorillonite(OMMT)and magnesium hydroxide(MH)were used as co-effectors respectively,and the flame retardant PUA(PUA/DOPO-N/OMMT and PUA/DOPO-N/MH)were also prepared.Thermal properties,flame retardant properties,flame retardant mechanism and mechanical properties of PUA/DOPO-N,PUA/DOPO-N/OMMT and PUA/DOPO-N/MH were investigated by thermogravimetric(TG)analysis,limiting oxygen index(LOI),UL 94,cone calorimeter test,scanning electron microscopy(SEM),and tensile test.The results show that the LOI value of PUA/20%DOPO-N,PUA/18%DOPO-N/2%OMMT and PUA/15%DOPO-N/5%MH are 27.1%,27.7%,and 28.3%,respectively,and UL 94 V-0 rating is attained.Compared with PUA,the peak heat release rate(pk-HRR),total heat release(THR)and average effective heat combustion(av-EHC)of PUA/20%DOPO-N,PUA/18%DOPO-N/2%OMMT and PUA/15%DOPO-N/5%MH decrease significantly.SEM results indicate that the residual chars of PUA/20%DOPO-N,PUA/18%DOPO-N/2%OMMT and PUA/15%DOPO-N/5%MH are completer and more compact.The complex of DOPO-N/OMMT and DOPO-N/MH have synergistic flame retardancy.The mechanical properties of PUA can be improved by the addition of DOPO-N,DOPO-N/OMMT and DOPO-N/MH,respectively.The insulation performance test shows that the volume resistivity of PUA/20%DOPO-N is 6.25×10^(16)Ω.cm.Furthermore,by using modified boron nitride(MBN)as heat dissipating material,the complex of PUA/MBN was prepared,and the thermal conductivity of PUA/MBN was investigated.The thermal conductivity of PUA/8%MBN complex coating at room temperature is 0.166 W/(M·K),which is a 163%improvement over pure PUA.

Fire Retardant Mechanisms of Polymer Fire-retardant and Extinguishing Gels

This study evaluates the performance of polymer fire-retardant and extinguishing gels through experimental comparisons with traditional foam extinguishing agents and water.The findings indicate that polymer fire-retardant and extinguishing gels exhibit significant advantages over conventional water and foam in terms of fire suppression and prevention of re-ignition.Based on these results,the fire retardant mechanisms of the polymer gel are hypothesized.

Ten-Minute Synthesis of a New Redox-Active Aqueous Binder for Flame-Retardant Li-S Batteries

As a critical role in battery systems,polymer binders have been shown to efficiently suppress the lithium polysulfide shuttling and accommodate volume changes in recent years.However,preparation processes and safety,as the key criterions for Li-S batteries'practical applications,still attract less attention.Herein,an aqueous multifunction binder(named PEI-TIC)is prepared via an easy and fast epoxy-amine ring-opening reaction(10 min),which can not only give the sulfur cathode a stable mechanical property,a strong chemical adsorption and catalytic conversion ability,but also a fire safety improvement.The Li-S batteries based on the PEI-TIC binder display a high discharge capacity(1297.8 mAh g^(-1)),superior rate performance(823.0 mAh g^(-1)at 2 C),and an ultralow capacity decay rate of 0.035%over more than 800 cycles.Even under 7.1 mg cm^(-2)S-loaded,the PEI-TIC electrode can also achieve a high areal capacity of 7.2 mA h g^(-1)and excellent cycling stability,confirming its application potential.Moreover,it is also noted that TG-FTIR test is performed for the first time to explore the flame-retardant mechanism of polymer binders.This work provides an economically and environmentally friendly binder for the practical application and inspires the exploration of the flame-retardant mechanism of all electrode components.

Research Progress in Flame Retardant in Flame Retardant Coatings

Flame retardant coatings are functional materials that can serve as decorative and protec-tive substrates in the event of a fire.Flame retardant coatings generally consist of two parts:a base material and a flame retardant agent.A detailed introduction was given to the development of flame retardant coatings in recent years and the flame retardants used in flame retardant coatings.Flame retardants mainly include halogen flame retar-dants,phosphorus nitrogen flame retardants,expansion flame retardants,biomass flame retardants,and graphene flame retardants.The application of flame retardant coatings in the fields of epoxy resin,polyurethane,etc.was elaborated.In addition,the application of new biomass flame retardants and graphene flame retardants was introduced,and the future development of flame retardant coatings and flame retardants was described.

Synthesis of Organic-Inorganic Hybrid Aluminum Hypophosphite Microspheres Flame Retardant and Its Flame Retardant Research on Thermoplastic Polyurethane

Aluminum hypophosphite microspheres(AHP) were synthesized by hydrothermal method using NaH2PO2·H2O and AlCl3·6H2O as raw materials, and then the AHP microspheres were polymerized by surface polymerization of micro-nanospheres with cyclic cross-linked poly(cyclotriphosphazene-co-4,4'-sulfonyldiphenol)(PZS). A new organic-inorganic poly(phosphonitrile)-modified aluminum hypophosphite microspheres(PZS-AHP) were synthesized by encapsulation and applied to flame retardant thermoplastic polyurethane(TPU). The microstructure and chemical composition of the PZS-AHP microsphere were characterized by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy and X-ray spectroscopy. The thermal stability of PZS-AHP microsphere was explored with thermogravimetric analysis. Thermogravimetric data indicate that the PZS-AHP microspheres have excellent thermal stability. The thermal and flame-retarding properties of the TPU composites were evaluated by thermogravimetric(TG), limited oxygen index tests(LOI), and cone calorimeter test(CCT). The TPU composite achieved vertical burning(UL-94) V-0 grade and LOI value reached 29.2% when 10 wt% PZS-AHP was incorporated. Compared with those of pure TPU, the peak heat release rate(pHRR) and total heat release(THR) of TPU/10%PZS-AHP decreased by 82.2% and 42.5%, respectively. The results of CCT indicated that PZS-AHP microsphere could improve the flame retardancy of TPU composites.

Flame Retardant Material Based on Cellulose Scaffold Mineralized by Calcium Carbonate

Wood-based functional materials have developed rapidly.But the flammability significantly limits its further application.To improve the flame retardancy,the balsa wood was delignified by NaClO2 solution to create a cellulose scaffold,and then alternately immersed in CaCl_(2) ethanol solution and NaHCO3 aqueous solution under vacuum.The high porosity and wettability resulting from delignification benefited the following mineralization process,changing the thermal properties of balsa wood significantly.The organic-inorganic wood composite showed abundant CaCO_(3) spherical particles under scanning electron microscopy.The peak of the heat release rate of delignified balsa-CaCO_(3) was reduced by 33%compared to the native balsa,according to the cone calorimetric characterization.The flame test demonstrated that the mineralized wood was flame retardant and selfextinguish.Additionally,the mineralized wood also displayed lower thermal conductivity.This study developed a feasible way to fabricate a lightweight,fire-retardant,self-extinguishing,and heat-insulating wood composite,providing a promising route for the valuable application of cellulosic biomass.

Biobased Furfurylated Poplar Wood for Flame-Retardant Modification with Boric Acid and Ammonium Dihydrogen Phosphate

Furfurylated wood exhibits excellent dimensional stability and corrosion resistance,making it a promising material for constructing buildings,but it is highly flammable.Herein,flame-retardant furfurylated poplar wood was produced via a two-step process utilizing boric acid(BA)and ammonium dihydrogen phosphate(ADP)as flame-retardant components,and biomass-derived furfuryl alcohol(FA)as a modifier.The acidity of BA and ADP allowed them to catalyze the polymerization of FA,which formed a cross-linked network that immobilized BA and ADP inside the wood.The addition of BA/ADP substantially delayed the time to ignition from 10 to 385 s and reduced the total heat release and total smoke release by 58.75%and 77.31%,respectively.Analysis of the pyrolysis process showed that the decomposition products of BA and ADP protected the underlying furfurylated wood and diluted combustible gases.This method significantly improved the fire retardancy and smokeless properties of furfurylated wood,providing promising prospects for its application as an engineering material.

Intumescent Flame-retardant Modification of Polypropylene/Carbon Fiber Composites

To improve the flame resistance of polypropylene(PP)/carbon fiber(CF)composite materials,triazine char-forming agent(TCA)was compounded with ammonium polyphosphate(APP)or modified APP(CS-APP)in a 2:1 ratio to prepare intumescent flame retardant(IFR)and the modified intumescent flame retardant(CS-IFR)in this paper.Flame retardancy and thermal degradation behaviors of the composites modified by IFR and CS-IFR were characterized by Fourier Transform Infrared(FTIR),contact angle measurement,oxygen index(OI),vertical burning tests(UL-94),thermogravimetric analyer(TGA),and thermogravimetric analyzer coupled with Fourier transform infrared(TG-FTIR).It was found that 25.0 phr of IFR and 24.0 phr of CS-IFR could improve the LOI value of PP/CF composites to 28.3%and 28.9%,respectively.At the same time,a UL-94 V-0 rating was achieved.The experimental results show that the IFR and CS-IFR prepared could effectively improve the flame retardancy and thermostability of PP/CF composites,and they would greatly expand the application range of PP/CF composite materials.

Research on the effect of the common flame retardant in reducing the flammability of the bitumen

The bituminous defect that the binder is flammable will bring road safety risk.Once it catches fires,large quantities of heat,smoke and poisonous gas are produced,released and spread quickly,which seriously hinder escape and rescue and harms heavily traffic safety.The common flame retardant system is used to modify the asphalt.Cone Calorimeter is adopted to evaluate the burning property of asphalt.The performance of the flame retardant is evaluated by limiting oxygen index and orthogonal design method.The paper analyzes the synergism of the asphalt and flame-retardant,and analyzes the effect of the flame on preventing the smoke to spread and demonstrates that the use of common flame retardants which is added into binder is good at reducing the flammability of the binder.This way can increase the safety of asphalt pavement when fire occurs in the tunnel.The study suggests that flame retardancy of asphalt can be evaluated by Limit Oxygen Index (LOI) and the flame retardancy property of asphalt has marked change according to the content of flame retardant.SB has perfect flame retardancy property,and ATH is better than MH in the effect of flame retardant.

Synthesis and Structure of A Novel Caged Bicyclic Phosphate Flame Retardant

PI novel caged bicyclic phosphate flame retardant tri(1-oxo-2,6,7-trioxa-1-phosphabicyclo [2.2.2] octane-methyl) phosphate (Trimer) was synthesized from 1-oxo-4-hydroxymethyl-2,6,7-trioxa-1-phosphabicyclo [2.2.2] octane (PEPA) and phosphorus oxychloride in this paper. Its structure was characterized by elemental analysis. FTIR, H-1 NMR. P-31 NMR and X-ray diffraction analysis.

Microencapsulated ammonium polyphosphate by polyurethane with segment of dipentaerythritol and its application in flame retardant polypropylene

Dipentaerythritol(DPER),4,40-diphenylmethanediisocyanate(MDI)and melamine(MEL)are used as raw materials to microencapsulate ammonium polyphosphate(MAPP)in situ polymerization.The MAPP is characterized by Fourier transform infrared(FT-IR),scanning electron microscopy(SEM),transmission electron microscopy(TEM)and thermal gravimetric analysis(TGA).The results show that the coating operation can effectively improve water resistance of ammonium polyphosphate(APP),and MAPP has higher residual rate than that of APP after combustion.The flame retardant action of MAPP and APP in polypropylene(PP)is investigated by the limited oxygen index(LOI),vertical burning test(UL-94),TGA,SEM,and cone calorimeter test(CCT).The LOI value of the PP/MAPP composite at the same loading is higher than that of PP/APP composite.UL 94 ratings of PP/MAPP composites are raised to V-0 at 20 wt%loading.The results of CCT also show that MAPP is more efficient than APP.The morphological structures observed by digital photos and SEM demonstrated that MAPP could be promoted to form the continuous and compact intumescent char layer.The flame retardant mechanism of PP/MAPP is also discussed.

Levels and distribution of brominated flame retardants in the soil of Harbin in China

This study reports the presence of brominated flame retardants in the topsoil in and around Harbin, a city in northeastern China. Samples of soil were collected from 17 locations in 2006, and the levels of 9 polybrominated diphenylethers （PBDEs 17, 28, 47, 66, 99, 100, 153, 154, and 183） ranged from 2.45 to 55.9 pg/g dry weight （dw） with a mean of 26.3 pg/g dw. These levels are very low comparing with those for some cities in Europe and USA. BDE 209 and hexabromocyclododecane were the two dominant congeners, with mean concentrations of 520 pg/g dw and 1750 pg/g dw, respectively. The concentrations of the total nine PBDE congeners clearly decreased from urban areas to background, but the compositions of individual congeners differed. Proportions of heavier congeners decreased while those of lighter congeners increased, along urban-rural-background transect, providing evidence for an urban fractionation effect. Correlation analysis indicated similar sources for PBDEs, hexabromocyclododecane, and 1,2-bis（2,4,6-tribromophenoxy）-ethane from urban areas but pentabromoethylbenzene was probably present due to long-range atmospheric transport. Principal component analysis was used to determine the characteristics of the relationships among these brominated flame retardants in the field.

Synergistic effect of MXene on the flame retardancy and thermal degradation of intumescent flame retardant biodegradable poly(lactic acid)composites

The effect of Ti3C2 MXene nanosheets on the intumescent flame retardant(IFR)poly(lactic acid)(PLA)composites was investigated among a series of PLA/IFR/MXene,which were prepared by melt blending 0-2.0 wt%MXene,10.0 wt%-12.0 wt%IFR and PLA together.The results of limiting oxygen index(LOI)and vertical burning(UL-94)discover that the combination of 0.5 wt%MXene and 11.5 wt%IFR synergistically improves the fire safety of PLA to reach UL-94 V-0 rating with LOI value of 33.0%.The PLA/IFR/MXene composites perform an obvious reduction in peak of heat release rate(HRR)in cone calorimeter tests(CCTs).Furthermore,the carbon residues after CCTs were characterized by scanning electron microscope(SEM),laser Raman spectroscopy(LRS),X-ray diffraction(XRD)and X-ray photoelectron spectroscopy(XPS).It is demonstrated that both the titanium composition of the MXene structure and the characteristics of the two-dimensional material enhance the PLA/IFR/MXene composite materials’ability to produce a dense barrier layer to resist burnout during thermal degradation.

Synthesis and thermal stability of a novel phosphorus-nitrogen containing intumescent flame retardant

A novel phosphorus-nitrogen containing intumescent flame retardant （P-N IFR） was prepared via the reaction of dichlor-opentate with N-methylaniline. The structure of the product was confirmed by ^1H NMR, ^31p NMR, MS and IR. TGA analysis showed it has effective thermal stability.

Preparation and characterization of tung oil-based flame retardant polyols

Three kinds of tung oil-based structural flame retardants polyols(TOFPs) were prepared by new methods in this paper. First, tung oil was used to produce monoglyceride and diglyceride by transesterification with glycerol by sodium methoxide. The products after transesterification were epoxidized by peracetic acid which was in-situ generated from acetic acid and hydrogen peroxide in the presence of sulfuric acid catalyst. And then, TOFPs were prepared from epoxidized alcoholysis tung oil(EGTO) with 9, 10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide(DOPO), diethyl phosphate(DEP) and diethanolamine(DEA) by ring-opening reactions, respectively. GPC was used to evaluate the conversion rate, at optimum reaction conditions, selectivity for monoglyceride in transesterification. The influence of different parameters such as temperature, mole ratio or mass ratio on the conversion rate of transesterification and epoxidation were investigated. The molecular structures of TOFPs were characterized by FTIR and ~1HNMR. Finally, tung oil-based polyurethane foams(TOPUFs) were prepared by a one-shot process using TOFPs with polyisocyanate. The LOI values of TOPUFs whose content of DOPO-EGTO,DEP-EGTO and DEA-EGTO were 100 wt% can reach to 26.2%, 25.1%, and 24.4%, respectively.

Synthesis and Application of Novel Triazine-Based Charring-Foaming Agents in Intumescent Flame Retardant Polypropylene

Three novel triazine-based charring-foaming agents (M2-CFA, M4-CFA, and M6-CFA) were synthesized successfully with only water as the solvent and were characterized by FT-IR and thermal gravimetric analysis (TGA). These three charring-foaming agents and the byproduct 944-by were employed to study the effectiveness of the novel intumescent flame retardant dopant on the fire retardancy of polypropylene(PP) investigated through UL-94 and limiting oxygen index (LOI) tests. TGA results showed that the M4-CFA presented good char formation ability (char residue: 26.8% at 700 °C). It was found that the sample with a 2/1 mass ratio of APP to M4-CFA exhibited the best flame retardancy among all the PP composites: 35.5% LOI and a V-0 rating of UL-94. Additionally, the microstructure and morphology of char residues were further studied by XRD, Raman spectroscopy and SEM. © 2017, Tianjin University and Springer-Verlag Berlin Heidelberg.

A NEW SYNERGIST FOR INTUMESCENT FLAME RETARDANT POLYPROPYLENE

The synergistic effects of silicotungstic acid (SiW12) as a catalyst in the phosphorus-nitrogen compounds AM-based intumescent flame-retardant (IFR) polypropylene (PP) were studied using the limiting oxygen index (LOI), the UL-94 test, thermogravimetric analysis (TGA), real time Fourier transform infrared (FTIR), laser Raman spectroscopy (LRS). The LOI data show that SiW12 added to PP/IFR systems has a synergistic FR effect with an IFR additive named AM. The TGA data show that SiW12 apparently increases the thermal stability of the PP/IFR systems at high temperature (T > 500degreesC). The FTIR results provide the positive evidence that IFR can improve the thermal stability of PP and SiW12 can induce a higher rate of formation of phosphoric acid and its derivatives. The LRS measurements provide useful information on the carbonaceous microstructures. In short, a suitable amount of SiW12 (1.5 wt%) exerts synergistic effects with the IFR by increasing the LOI value and the thermal stability at high temperature and promoting the formation of charred structures on the burning PP surface.

STUDIES ON FLAME-RETARDANT PC/ABS MULTIPLE-ELEMENT ALLOY

The preparation technology of flame-retardant PC/ABS alloys was studied in this paper. Using a high-efficiency flame retardant system and by means of multiple-ingredient compatibilizing, PC/ABS alloys with excellent impact strength and flame retardant property were prepared. The experimental results showed that by using PS-g-MAH and SMA as synergistic compatibilizers, the notched Izod impact strength and flammability of PC/ABS alloy obtained in the present work can be up to 175 J/m and UL-94 VO, respectively.

Preparation and Properties of Bio-Based Flame Retardant Polyvinyl Alcohol

Polyvinyl alcohol (PVA) has been widely used in the fields of medical, food and packaging due to its excellentbiocompatibility, good fiber-forming and film-forming properties. However, the high flammability of PVA hasgreatly limited its wider applications. The flame-retardant PVA was prepared by melt blending of a bio-basedflame retardant (prepared from lignin, phosphoric acid and carbamide) with thermoplastic PVA (TPVA). Thechemical structure, morphology, thermal properties, mechanical properties, fire property and fluidity of thisflame retardant PVA were investigated by Fourier transform infrared spectrometer(FTIR), field emission scanning electron microscope(SEM), thermogravimetric analyzer(TGA), impact tester, universal testing machine,horizontal-vertical burning tester, limiting oxygen indexer(LOI) and melt flow rate meter(MFR). The resultsshowed that the prepared flame retardant had good compatibility with the PVA substrate;The impact strength,melt flow rate, fire property and char residue of this PVA material increased with the content of bio-based flameretardant. When the content of flame retardant was of 20%, the five indices including impact strength, meltflow rate, UL-94 level, LOI and char residual were 11.3 KJ/m^(2), 21.2 g/10 min, V-0 UL-94 level, 33.1%, and19.2%, respectively. This research can promote the high-value utilization of lignin and the application ofPVA in the fields of fire protection.