To elucidate the high temperature rheological capability of graphene modified rubber asphalt,three contents of graphene and crumb rubber were prepared by a combination of mechanical agitation and high speed shearing m...To elucidate the high temperature rheological capability of graphene modified rubber asphalt,three contents of graphene and crumb rubber were prepared by a combination of mechanical agitation and high speed shearing machine,then used dynamic shear rheological test(DSR)and multiple stress creep recovery(MSCR)tests to evaluate.The hardness and softening point with rotational viscosity of samples raised with the addition of graphene,especially the addition of 0.04%.Dynamic shear rheological test revealedthat the dynamic shear modulus G*,rutting factor G*/Sin δ,and zero shear viscosity(ZSV)of graphene-modified rubber asphalt were greatly influenced along with graphene-increased,on the contrary,phase angle δ which characterize the viscoelastic ratio of asphalt decreased.Multiple stress creep recovery(MSCR)tests showed that the graphene-enhanced rubber asphalt had high-temperature stability through non-recoverable creep compliance(Jnr).Based on these findings,graphene-modified rubber asphalt binders with the addition of 0.04% graphene had good viscoelastic properties as well as high temperature rutting resistance performance.In the meantime,G*/Sin δ,ZSV,and Jnr100,Jnr3200 have good correlation,which can reveal the excellent high-temperature stability performance of asphalt.展开更多
Limited by mining technology,mineral exploitation can produce large amounts of tailings.Heavy summer rainfall or seasonal freeze-thaw can lead to physical and chemical modification of tailing material in mountainous a...Limited by mining technology,mineral exploitation can produce large amounts of tailings.Heavy summer rainfall or seasonal freeze-thaw can lead to physical and chemical modification of tailing material in mountainous areas,resulting in fluidized tailings flow and severe disaster losses.Therefore,aiming at the problem of tailings fluidization catastrophe,this paper tried to reveal the rheological mechanism of tailings fluidization transformation by combining rheological tests and theoretical analysis.The results show that the yield stress increases with decreasing temperature,and when the density of debris flow(ρ)is more than 1.9 g/cm~3,this behavior becomes more pronounced as the density increases.The storage modulus decreases by at least two orders of magnitude at the solid-fluid transition under amplitude test sweep.Storage and loss modulus in the linear viscoelastic range and yield stress have an exponential growth relationship with sediment concentration.In addition,a stress constitutive relation and a new exponential law describing the evolution of yield stress required for solid-liquid transformation were proposed,and the relationship is further strengthened through a comprehensive analysis of existing results,which expands the evaluation application of the rheological characteristics of tailings flow.This paper provides a new insight into the rheological properties of tailing and how they occur through solid-liquid transition under different environments,which is beneficial to geological hazard prevention and the ecological remediation of the mining area.展开更多
In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag ...In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag powder and mineral powder(limestone powder)were compared by scanning electron microscope(SEM),and the high-temperature rheological properties of asphalt mortar with difierent ratio of filler quality to asphalt quality(F/A)and difierent substitution rates of mineral powder(S/F)were studied by dynamic shear rheological test.The results show that the surface microstructure of steel slag powder is more abundant than that of mineral powder,and the adhesion of steel slag to asphalt is better than that of limestone.At the same temperature,the lower the ratio of S/F is,the greater the rutting factor and complex modulus will be.In addition,the complex modulus and rutting factor of the asphalt mortar increase with the increase of F/A,and the filler type and F/A have a negligible efiect on the phase angle.展开更多
Rod milling sand(RMS)—a coarse sand aggregate—was recycled for cemented paste backfill(CPB)for the underground mined area at the Jinchuan nickel deposit,named rod milling sand-based cemented paste backfill(RCPB).The...Rod milling sand(RMS)—a coarse sand aggregate—was recycled for cemented paste backfill(CPB)for the underground mined area at the Jinchuan nickel deposit,named rod milling sand-based cemented paste backfill(RCPB).The adverse effects of coarse particles on the transportation of CPB slurry through pipelines to underground stopes resulting in weakening of the stability of the backfill system are well known.Therefore,sulfonated naphthalene formaldehyde(SNF)condensate was used for the performance improvement of RCPB.The synergistic effect of solid content(SC),lime-to-sand ratio,and SNF dosage on the rheological and physicomechanical properties,including slump,yield stress,bleeding rate,uniaxial compressive strength(UCS),as well as mechanism analysis of RCPB,have been explored.The results indicate that the effect of SNF on RCPB performance is related to the SNF dosage,lime-to-sand ratio,and SC.The slump of fresh RCPB with 0.1wt%-0.5wt%SNF increased by 2.6%-26.2%,whereas the yield stress reduced by 4.1%-50.3%,indicating better workability and improved cohesiveness of the mix.The bleeding rate of fresh RCPB decreased first and then rose with the increase of SNF dosage,and the peak decrease was 67.67%.UCS of RCPB first increased and then decreased with the increase of SNF dosage.At the optimal SNF addition ratio of 0.3wt%,the UCS of RCPB curing for 7,14 and,28 d ages increased by 31.5%,28.4%,and 29.5%,respectively.The beneficial effects of SNF in enhancing the early UCS of RCPB have been corroborated.However,the later UCS increases at a slower rate.The research findings may guide the design and preparation of RCPB with adequate performance for practical applications.展开更多
Polypropylene(PP)grease holds great potential for special industrial applications.In this study,synthetic conditions,thickener content,and the ratio of two different molecular weight PPs were investigated systematical...Polypropylene(PP)grease holds great potential for special industrial applications.In this study,synthetic conditions,thickener content,and the ratio of two different molecular weight PPs were investigated systematically using a rheometer,scanning electron microscope,X-ray diffraction,Fourier transform infrared spectrometer,oscillating tribometer,and 3D surface profiler measurements.The results showed that suitable synthetic conditions are two quenching cycles,and the synthetic temperature and time is 240℃for 12 h.The rheological analysis showed that thickener content and different proportions of the two PP molecular weights have a significant influence on the rheological properties of PP grease.High molecular weight PP(H-PP)has a stronger thickening ability than low molecular weight PP(L-PP).The higher the amount of H-PP in the fixed thickener content or the higher the thickener content with a specific proportion,the higher the viscoelasticity of PP grease.The tribological performance is related to the rheological properties.The proportion of two different molecular weight PPs in the thickener content should be appropriate;excessive H-PP content leads to lubrication failure.展开更多
The filler-bitumen interaction mechanism is one of the most essential phases for comprehending the asphalt mixture's performance.However,despite numerous studies,in-depth knowledge of filler-bitumen reciprocity at...The filler-bitumen interaction mechanism is one of the most essential phases for comprehending the asphalt mixture's performance.However,despite numerous studies,in-depth knowledge of filler-bitumen reciprocity at a microscale level is yet to be ascertained.The goal of this research is to gain a better understanding of the fillerbitumen microscale interaction in terms of the synergy and coaction between the physicochemical and rheological performance of mastics due to filler inclusions.The rheological properties of two sustainable mastics,dolomite powder(DP)and lime kiln dust(LKD),together with a neat PEN 60/70 binder,were analysed based on a temperature sweep at elevated temperature conditions.Meanwhile,frequency sweep and multiple stress creep recovery(MSCR)tests were also conducted at pavement serviceability temperature using the dynamic shear rheometer(DSR).Physicochemical tests using a scanning electron microscope(SEM)and energy dispersive X-rays(EDX)were conducted to analyse the impact of parameters such as particle shape,grain size,texture,and chemical compositions.The DSR test results showcased how the incorporation of fillers in asphalt binder considerably improved the performance of the binder in terms of rutting and fatigue.Likewise,its strain and nonrecoverable compliance parameters were substantially reduced at higher filler and binder concentrations.Physical filler attributes of low rigden voids(R.V),high fineness modulus(FM),and high specific surface area(SSA)led to greater interfacial stiffness and elasticity in LKD mastics compared to DP mastics at different loading frequencies and temperature levels.The SEM/EDX results also indicated that the elemental calcium and carbon composition of each filler component,together with its grain morphology,strongly influenced its rheological performance.展开更多
To maintain tight control over rheological properties of high-density water-based drilling fluids, it is essential to understand the factors influencing the theology of water-based drilling fluids. This paper examines...To maintain tight control over rheological properties of high-density water-based drilling fluids, it is essential to understand the factors influencing the theology of water-based drilling fluids. This paper examines temperature effects on the rheological properties of two types of high-density water-based drilling fluids (fresh water-based and brine-based) under high temperature and high pressure (HTHP) with a Fann 50SL rheometer. On the basis of the water-based drilling fluid systems formulated in laboratory, this paper mainly describes the influences of different types and concentration of clay, the content of a colloid stabilizer named GHJ-1 and fluid density on the rheological parameters such as viscosity and shear stress. In addition, the effects of aging temperature and aging time of the drilling fluid on these parameters were also examined. Clay content and proportions for different densities of brine-based fluids were recommended to effectively regulate the rheological properties. Four theological models, the Bingham, power law, Casson and H-B models, were employed to fit the rheological parameters. It turns out that the H-B model was the best one to describe the rheological properties of the high-density drilling fluid under HTHP conditions and power law model produced the worst fit. In addition, a new mathematical model that describes the apparent viscosity as a function of temperature and pressure was established and has been applied on site.展开更多
The characters of basalt fiber are analyzed and compared with commonly used fibers. The rheological behaviors of the basalt fiber reinforced asphalt mastic are investigated by the dynamic shear rheological tests and t...The characters of basalt fiber are analyzed and compared with commonly used fibers. The rheological behaviors of the basalt fiber reinforced asphalt mastic are investigated by the dynamic shear rheological tests and the repeated creep tests. The results show that basalt fiber has excellent reinforced performances, such as high asphalt absorption ratio, low water absorption ratio, high tensile strength, high elastic modulus and high temperature stability. The rutting factor of the fiber reinforced asphalt mastic is higher than the plain asphalt mastic and the reinforced effects are more remarkable under high temperature. The rheological performances of the asphalt mastic demonstrate a good linear relationship between different temperature and loading frequency. The creep stiffness modulus of the asphalt mastic at different loading time can be expressed by power function. Improved Burgers model is used to represent the rheological behaviors of the asphalt mastic with basalt fiber and the model parameters are estimated.展开更多
The crustal texture and rheological evolution of the Tongbai-Dabie orogenic belt are approached from a physical standpoint on the basis of a large body of geological, chronological and geophysical data available in th...The crustal texture and rheological evolution of the Tongbai-Dabie orogenic belt are approached from a physical standpoint on the basis of a large body of geological, chronological and geophysical data available in the region. Rheological profiles showing variation of rock Strength with depth in the continental crust are constructed for 1-D crustal structure limited to the Present and Meso-Neoproterozoic structural configurations of the deformed belt, respectively .It is emphasized that the crustal texture and composition have been heterogeneous with the rheological stratification and complicated rheological evolution since the Meso-Neoproterozoic at least. The data appear that the Tongbai - Dabie tectonic belt is a polyphase collisional orogen with evidence for cyclically transition from compressional to extensional regimes and rheological behavior in the levels of the crust.展开更多
With many major projects under construction,more and more attention is paid to rheological mechanical properties of rock mass,and extensive researches are carried out for rheological constitutive modeling of rock mass...With many major projects under construction,more and more attention is paid to rheological mechanical properties of rock mass,and extensive researches are carried out for rheological constitutive modeling of rock mass.Based on viscoplastic theory,a new rheological constitutive model is proposed.The rationality and validity of proposed model are verified through the creep test data.The results show that the rheological constitutive model based on viscoplastic theory is able to simulate the typical creep curves of rock mass and the identified parameters are reasonable.Therefore,the rheological constitutive model could be used to describe the rheological mechanical behaviour of rock mass.展开更多
On a self-made super-high shear strain rate rheometer, the rheological characteristics and apparent viscosity curves of a high-speed bearing grease were obtained under different working conditions. A new grease rheolo...On a self-made super-high shear strain rate rheometer, the rheological characteristics and apparent viscosity curves of a high-speed bearing grease were obtained under different working conditions. A new grease rheological model suited to a shear strain rate range of 0—3.5×10~6s^(-1) was presented. The results showed that the shear stress increased linearly at first and then increased nonlinearly with the increase in shear strain rate up to 1.5×10~6s^(-1), and finally the shear stress decreased slightly with the successive increase in shear strain rate. The shear stress increased with a decreasing rolling speed and an increasing contact pressure. The apparent viscosity decreased rapidly with the increase of shear strain rate at beginning and could approach the viscosity of the base oil if the shear strain rate surpassed 1.5×10~6s^(-1). The fits between the test data and the predicted values by the new model were fairly good.展开更多
The Haihe cohesive sediment, which is typical in China, is studied systematically for its basic physical and incipient motion properties. Following the requirements of dredging works in the Haihe Estuary, cohesive sed...The Haihe cohesive sediment, which is typical in China, is studied systematically for its basic physical and incipient motion properties. Following the requirements of dredging works in the Haihe Estuary, cohesive sediment samples were taken from three locations. Laboratory experiments were conducted to determine the rheological properties of these samples and to examine the incipient motion of the cohesive sediment. It is found that the cohesive sediment has an obvious yield stress tau(b), which increases with the mud density in a manner of an exponential function, and so does the viscosity parameter eta. The cohesive sediment behaves like a Bingham fluid when its density is below 1.38 similar to 1.40 g/cm(3), and when denser than these values, it may become a power-law fluid. The incipient motion experiment also revealed that the incipient velocity of the cohesive sediment increases with die density in an exponential manner. Therefore, the incipient motion is primarily related to the density, which is different from the case for non-cohesive sediment in which the incipient motion is con-elated with the diameter of sand particles instead. The incipient motion occurs in two different ways depending on the concentration of mud in the bottom. For sufficiently fine particles and a concentration lower than 1.20 g/cm(3), the cohesive sediment appears as fluidized mud, and the incipient motion is in the form of instability of an internal wave. For a higher concentration, the cohesive sediment appears as general quasi-solid-mud, and the incipient motion can be described by a series of extended Shields curves each with a different porosity for newly deposited alluvial mud.展开更多
A series of Gd-doped Li-Ni ferrites with the formula of LiNi0.5GdxFe2-xO4 where x = 0.00 - 0.08 in steps of 0.02, were prepared by thermolysis of oxalate precursors obtained by rheological phase reaction. The structur...A series of Gd-doped Li-Ni ferrites with the formula of LiNi0.5GdxFe2-xO4 where x = 0.00 - 0.08 in steps of 0.02, were prepared by thermolysis of oxalate precursors obtained by rheological phase reaction. The structure, morphology, and the magnetic properties of the samples were characterized by powder X-ray diffraction (XRD), atomic force microscopy (AFM) and a vibrating sample magnetometer (VSM). A single spinel phase was obtained in the range of x = 0.00 - 0.04. The lattice parameters of the Gd-doped samples were larger than that of pure Li-Ni ferrite, and increased in the range of 0.00 ≤ x ≤ 0.04, then decreased up to x = 0.08, because of the formation of the secondary phase (Gd- FeO3). All samples were spheric particles with an average size of about 100 nm, but agglomerated to some extent. The hysteresis loops indicated that the saturation magnetization decreased gradually with increasing Gd content, while the variation of coercivity was related to the microstructure of the Gd-doped samples.展开更多
It is an effective way to use coal slime as fuel for circulating fluidized bed boilers, which will not only solve its pollution to the environment, but also turn waste to treasure. In order to provide basic technical ...It is an effective way to use coal slime as fuel for circulating fluidized bed boilers, which will not only solve its pollution to the environment, but also turn waste to treasure. In order to provide basic technical information for transportation of coal slime from the coal preparation plant to the boiler, this paper experimentally studied the rheological behaviors of coal slime produced by filter-pressing. By using a rotational viscometer, the influences of water content, temperature, and shear time on the rheological behaviors of coal slime were investigated. Experimental results show that the coal slime will behave like Bingham plastics with low water content and like Bingham pseudo-plastics with 37.5% water content,while like pseudo-plastics with 40% water content. This indicates that the water content of coal slime must be controlled in consideration of both transportation resistance and combustion efficiency. Study results also show that, the apparent viscosity of coal slime at 5℃ is about 1.5–1.7 times of that at 40℃ for water contents 32%–37.5%, while the influence of temperature can be neglected when the water content is 40%. With increasing of water content, the influences of shear time on the apparent viscosity of coal slime becomes less. When the water content is more than 30%, the effect of shear time is negligible. It indicates that water content has the most important influence on the rheological behaviors of coal slime. There must be an optimal water content in considering conveying resistance and combustion efficiency. The environmental temperature must also be considered in coal slime transportation.展开更多
The rheological behavior of a soft interlayer is critical to understanding slope stability, which is closely related to the water content of the soft interlayer. This study used the soft interlayer of the Permian Maok...The rheological behavior of a soft interlayer is critical to understanding slope stability, which is closely related to the water content of the soft interlayer. This study used the soft interlayer of the Permian Maokou Formation in Southwest China as an example to perform ring shear creep tests with different water content amounts. The effect of water content on the creep properties of the soft interlayer was analyzed, and a new shear rheological model was established. This research produced several findings. First, the ring shear creep deformation of the soft interlayer samples varied with the water content and the maximum instantaneous shear strain increment occurred near the saturated water content. As the water content increased, the cumulative creep increment of the samples increased. Second, the water content significantly affected the long-term strength of the soft interlayer, which decreased with the increase of water content, exhibiting a negative linear correlation. Third, a constitutive equation for the new rheological model was derived, and through fitting of the ring shear creep test data, the validity and applicability of the constitutive equation were proven. This study has developed an important foundation for studying the long-term deformation characteristics of a soft interlayer with varying water content.展开更多
Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on ...Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. 'the second plateau', appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.展开更多
As for ceramic stereolithography technique,the preparation of suitable resin-based ceramic slurry is of primary importance.In this study,the effects of powder characteristics such as specific surface area,particle siz...As for ceramic stereolithography technique,the preparation of suitable resin-based ceramic slurry is of primary importance.In this study,the effects of powder characteristics such as specific surface area,particle size and distribution,particle morphology on the rheological behavior of zirconia resin-based suspensions were investigated intensively.Results show that the specific surface area of the powder is the most important factor affecting slurry viscosity.Choosing low specific surface area and quasi-spherical shaped powder is more likely to obtain low viscosity slurries.In addition,the influence of solid loading on the flow behavior were also studied using Krieger-Dougherty model.Zirconia samples with the relative density of(97.83±0.33)%were obtained after sintering at 1550℃.No obvious abnormal grain growth in the microstructure of the sintered body is observed.Results indicate that after the optimization of the processing parameters with the help of rheology characterization,complex-shaped high-quality zirconia parts can be obtained using the stereolithography technique.展开更多
The traction capacity of the mining machine is greatly in?uenced by the traction rheological properties of the deep-sea sediments. The best simulative soil was prepared for substituting the deep-sea sediment based on ...The traction capacity of the mining machine is greatly in?uenced by the traction rheological properties of the deep-sea sediments. The best simulative soil was prepared for substituting the deep-sea sediment based on the deep-sea sediment collected from the Paci?c C-C mining area. Traction rheological properties of the simulative soil were studied by a home-made test apparatus. In order to accurately describe the traction rheological properties and determine traction rheological parameters, the Newtonian dashpot in Maxwell body of Burgers model was replaced by a self-similarity spring-dashpot fractance and a new rheological constitutive model was deduced by fractional derivative theory. The results show the simulative soil has obvious non-attenuate rheological properties. The transient creep and stable creep rate increase with the traction, but they decrease with ground pressure. The fractional derivative Burgers model are better in describing non-attenuate rheological properties of the simulative soil than the classical Burgers model. For the new traction rheological constitutive equation of the simulative soil, the traction rheological parameters can be obtained by ?tting the tested traction creep data with the traction creep constitutive equation. The ground contact length of track and walking velocity of the mining machine predicted by the traction rheological constitutive equation can be used to take full advantages of the maximum traction provided by the soil and safely improve mining effciency.展开更多
The dynamic rheological measurements have been a preferred approach to the characterization of the structure and properties for multi-component or multi-phase polymer systems,due to its sensitive response to changes o...The dynamic rheological measurements have been a preferred approach to the characterization of the structure and properties for multi-component or multi-phase polymer systems,due to its sensitive response to changes of structure for these heterogeneous polymers.In the present article,recent progresses in the studies on dynamic rheology for heterogeneous polymer systems including polymeric composites filled with inorganic particles,thermo-oxidized polyolefins,phase- separated polymeric blends and functional polymers with the scaling and percolation behavior are reviewed,mainly depending on the results by the authors' group.By means of rheological measurements,not only some new fingerprints responsible for the evolution of morphology and structure concerning these polymer systems are obtained,the corresponding results are also significant for the design and preparation of novel polymer-based composites and functional materials.展开更多
文摘To elucidate the high temperature rheological capability of graphene modified rubber asphalt,three contents of graphene and crumb rubber were prepared by a combination of mechanical agitation and high speed shearing machine,then used dynamic shear rheological test(DSR)and multiple stress creep recovery(MSCR)tests to evaluate.The hardness and softening point with rotational viscosity of samples raised with the addition of graphene,especially the addition of 0.04%.Dynamic shear rheological test revealedthat the dynamic shear modulus G*,rutting factor G*/Sin δ,and zero shear viscosity(ZSV)of graphene-modified rubber asphalt were greatly influenced along with graphene-increased,on the contrary,phase angle δ which characterize the viscoelastic ratio of asphalt decreased.Multiple stress creep recovery(MSCR)tests showed that the graphene-enhanced rubber asphalt had high-temperature stability through non-recoverable creep compliance(Jnr).Based on these findings,graphene-modified rubber asphalt binders with the addition of 0.04% graphene had good viscoelastic properties as well as high temperature rutting resistance performance.In the meantime,G*/Sin δ,ZSV,and Jnr100,Jnr3200 have good correlation,which can reveal the excellent high-temperature stability performance of asphalt.
基金supported by The National Nat ural Science Foundation of China(No.42207184)Nature Science Basic Research Plan in Shaanxi Provi nce of China(No.2022JQ-253)。
文摘Limited by mining technology,mineral exploitation can produce large amounts of tailings.Heavy summer rainfall or seasonal freeze-thaw can lead to physical and chemical modification of tailing material in mountainous areas,resulting in fluidized tailings flow and severe disaster losses.Therefore,aiming at the problem of tailings fluidization catastrophe,this paper tried to reveal the rheological mechanism of tailings fluidization transformation by combining rheological tests and theoretical analysis.The results show that the yield stress increases with decreasing temperature,and when the density of debris flow(ρ)is more than 1.9 g/cm~3,this behavior becomes more pronounced as the density increases.The storage modulus decreases by at least two orders of magnitude at the solid-fluid transition under amplitude test sweep.Storage and loss modulus in the linear viscoelastic range and yield stress have an exponential growth relationship with sediment concentration.In addition,a stress constitutive relation and a new exponential law describing the evolution of yield stress required for solid-liquid transformation were proposed,and the relationship is further strengthened through a comprehensive analysis of existing results,which expands the evaluation application of the rheological characteristics of tailings flow.This paper provides a new insight into the rheological properties of tailing and how they occur through solid-liquid transition under different environments,which is beneficial to geological hazard prevention and the ecological remediation of the mining area.
基金Funded by National Natural Science Foundation of China(No.52278446)。
文摘In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag powder and mineral powder(limestone powder)were compared by scanning electron microscope(SEM),and the high-temperature rheological properties of asphalt mortar with difierent ratio of filler quality to asphalt quality(F/A)and difierent substitution rates of mineral powder(S/F)were studied by dynamic shear rheological test.The results show that the surface microstructure of steel slag powder is more abundant than that of mineral powder,and the adhesion of steel slag to asphalt is better than that of limestone.At the same temperature,the lower the ratio of S/F is,the greater the rutting factor and complex modulus will be.In addition,the complex modulus and rutting factor of the asphalt mortar increase with the increase of F/A,and the filler type and F/A have a negligible efiect on the phase angle.
基金financially supported by the National Natural Science Foundation of China(Nos.52104156,52074351,52004330)the Science and Technology Innovation Program of Hunan Province,China(No.2021RC3125)the Natural Science Foundation of Hunan Province,China(No.2022JJ30714)。
文摘Rod milling sand(RMS)—a coarse sand aggregate—was recycled for cemented paste backfill(CPB)for the underground mined area at the Jinchuan nickel deposit,named rod milling sand-based cemented paste backfill(RCPB).The adverse effects of coarse particles on the transportation of CPB slurry through pipelines to underground stopes resulting in weakening of the stability of the backfill system are well known.Therefore,sulfonated naphthalene formaldehyde(SNF)condensate was used for the performance improvement of RCPB.The synergistic effect of solid content(SC),lime-to-sand ratio,and SNF dosage on the rheological and physicomechanical properties,including slump,yield stress,bleeding rate,uniaxial compressive strength(UCS),as well as mechanism analysis of RCPB,have been explored.The results indicate that the effect of SNF on RCPB performance is related to the SNF dosage,lime-to-sand ratio,and SC.The slump of fresh RCPB with 0.1wt%-0.5wt%SNF increased by 2.6%-26.2%,whereas the yield stress reduced by 4.1%-50.3%,indicating better workability and improved cohesiveness of the mix.The bleeding rate of fresh RCPB decreased first and then rose with the increase of SNF dosage,and the peak decrease was 67.67%.UCS of RCPB first increased and then decreased with the increase of SNF dosage.At the optimal SNF addition ratio of 0.3wt%,the UCS of RCPB curing for 7,14 and,28 d ages increased by 31.5%,28.4%,and 29.5%,respectively.The beneficial effects of SNF in enhancing the early UCS of RCPB have been corroborated.However,the later UCS increases at a slower rate.The research findings may guide the design and preparation of RCPB with adequate performance for practical applications.
基金the financial support provided by the National Natural Science Foundation of China Project (U21A20315,21978186)the Fund for Shanxi“1331 Project” (1331)。
文摘Polypropylene(PP)grease holds great potential for special industrial applications.In this study,synthetic conditions,thickener content,and the ratio of two different molecular weight PPs were investigated systematically using a rheometer,scanning electron microscope,X-ray diffraction,Fourier transform infrared spectrometer,oscillating tribometer,and 3D surface profiler measurements.The results showed that suitable synthetic conditions are two quenching cycles,and the synthetic temperature and time is 240℃for 12 h.The rheological analysis showed that thickener content and different proportions of the two PP molecular weights have a significant influence on the rheological properties of PP grease.High molecular weight PP(H-PP)has a stronger thickening ability than low molecular weight PP(L-PP).The higher the amount of H-PP in the fixed thickener content or the higher the thickener content with a specific proportion,the higher the viscoelasticity of PP grease.The tribological performance is related to the rheological properties.The proportion of two different molecular weight PPs in the thickener content should be appropriate;excessive H-PP content leads to lubrication failure.
文摘The filler-bitumen interaction mechanism is one of the most essential phases for comprehending the asphalt mixture's performance.However,despite numerous studies,in-depth knowledge of filler-bitumen reciprocity at a microscale level is yet to be ascertained.The goal of this research is to gain a better understanding of the fillerbitumen microscale interaction in terms of the synergy and coaction between the physicochemical and rheological performance of mastics due to filler inclusions.The rheological properties of two sustainable mastics,dolomite powder(DP)and lime kiln dust(LKD),together with a neat PEN 60/70 binder,were analysed based on a temperature sweep at elevated temperature conditions.Meanwhile,frequency sweep and multiple stress creep recovery(MSCR)tests were also conducted at pavement serviceability temperature using the dynamic shear rheometer(DSR).Physicochemical tests using a scanning electron microscope(SEM)and energy dispersive X-rays(EDX)were conducted to analyse the impact of parameters such as particle shape,grain size,texture,and chemical compositions.The DSR test results showcased how the incorporation of fillers in asphalt binder considerably improved the performance of the binder in terms of rutting and fatigue.Likewise,its strain and nonrecoverable compliance parameters were substantially reduced at higher filler and binder concentrations.Physical filler attributes of low rigden voids(R.V),high fineness modulus(FM),and high specific surface area(SSA)led to greater interfacial stiffness and elasticity in LKD mastics compared to DP mastics at different loading frequencies and temperature levels.The SEM/EDX results also indicated that the elemental calcium and carbon composition of each filler component,together with its grain morphology,strongly influenced its rheological performance.
文摘To maintain tight control over rheological properties of high-density water-based drilling fluids, it is essential to understand the factors influencing the theology of water-based drilling fluids. This paper examines temperature effects on the rheological properties of two types of high-density water-based drilling fluids (fresh water-based and brine-based) under high temperature and high pressure (HTHP) with a Fann 50SL rheometer. On the basis of the water-based drilling fluid systems formulated in laboratory, this paper mainly describes the influences of different types and concentration of clay, the content of a colloid stabilizer named GHJ-1 and fluid density on the rheological parameters such as viscosity and shear stress. In addition, the effects of aging temperature and aging time of the drilling fluid on these parameters were also examined. Clay content and proportions for different densities of brine-based fluids were recommended to effectively regulate the rheological properties. Four theological models, the Bingham, power law, Casson and H-B models, were employed to fit the rheological parameters. It turns out that the H-B model was the best one to describe the rheological properties of the high-density drilling fluid under HTHP conditions and power law model produced the worst fit. In addition, a new mathematical model that describes the apparent viscosity as a function of temperature and pressure was established and has been applied on site.
基金Funded by The National Natural Science Foundation of China(No.51108082)
文摘The characters of basalt fiber are analyzed and compared with commonly used fibers. The rheological behaviors of the basalt fiber reinforced asphalt mastic are investigated by the dynamic shear rheological tests and the repeated creep tests. The results show that basalt fiber has excellent reinforced performances, such as high asphalt absorption ratio, low water absorption ratio, high tensile strength, high elastic modulus and high temperature stability. The rutting factor of the fiber reinforced asphalt mastic is higher than the plain asphalt mastic and the reinforced effects are more remarkable under high temperature. The rheological performances of the asphalt mastic demonstrate a good linear relationship between different temperature and loading frequency. The creep stiffness modulus of the asphalt mastic at different loading time can be expressed by power function. Improved Burgers model is used to represent the rheological behaviors of the asphalt mastic with basalt fiber and the model parameters are estimated.
文摘The crustal texture and rheological evolution of the Tongbai-Dabie orogenic belt are approached from a physical standpoint on the basis of a large body of geological, chronological and geophysical data available in the region. Rheological profiles showing variation of rock Strength with depth in the continental crust are constructed for 1-D crustal structure limited to the Present and Meso-Neoproterozoic structural configurations of the deformed belt, respectively .It is emphasized that the crustal texture and composition have been heterogeneous with the rheological stratification and complicated rheological evolution since the Meso-Neoproterozoic at least. The data appear that the Tongbai - Dabie tectonic belt is a polyphase collisional orogen with evidence for cyclically transition from compressional to extensional regimes and rheological behavior in the levels of the crust.
基金Sponsored by the Natural Science Foundation of Fujian Province(Grant No.2008J0171)
文摘With many major projects under construction,more and more attention is paid to rheological mechanical properties of rock mass,and extensive researches are carried out for rheological constitutive modeling of rock mass.Based on viscoplastic theory,a new rheological constitutive model is proposed.The rationality and validity of proposed model are verified through the creep test data.The results show that the rheological constitutive model based on viscoplastic theory is able to simulate the typical creep curves of rock mass and the identified parameters are reasonable.Therefore,the rheological constitutive model could be used to describe the rheological mechanical behaviour of rock mass.
基金financially supported by the National Natural Science Foundation of China (No. 51475143)the Tianjin Natural Science Foundation (No.16JCYBJC18900)
文摘On a self-made super-high shear strain rate rheometer, the rheological characteristics and apparent viscosity curves of a high-speed bearing grease were obtained under different working conditions. A new grease rheological model suited to a shear strain rate range of 0—3.5×10~6s^(-1) was presented. The results showed that the shear stress increased linearly at first and then increased nonlinearly with the increase in shear strain rate up to 1.5×10~6s^(-1), and finally the shear stress decreased slightly with the successive increase in shear strain rate. The shear stress increased with a decreasing rolling speed and an increasing contact pressure. The apparent viscosity decreased rapidly with the increase of shear strain rate at beginning and could approach the viscosity of the base oil if the shear strain rate surpassed 1.5×10~6s^(-1). The fits between the test data and the predicted values by the new model were fairly good.
基金This research was supported by the National Natural Science Foundation of China(NSFC&RGC)under contract Nos.59809006 and 50279030and also supported by the Science Foundation of Tianjin Municipality under contract No.983702011,RGC of the Hong Kong Specia
文摘The Haihe cohesive sediment, which is typical in China, is studied systematically for its basic physical and incipient motion properties. Following the requirements of dredging works in the Haihe Estuary, cohesive sediment samples were taken from three locations. Laboratory experiments were conducted to determine the rheological properties of these samples and to examine the incipient motion of the cohesive sediment. It is found that the cohesive sediment has an obvious yield stress tau(b), which increases with the mud density in a manner of an exponential function, and so does the viscosity parameter eta. The cohesive sediment behaves like a Bingham fluid when its density is below 1.38 similar to 1.40 g/cm(3), and when denser than these values, it may become a power-law fluid. The incipient motion experiment also revealed that the incipient velocity of the cohesive sediment increases with die density in an exponential manner. Therefore, the incipient motion is primarily related to the density, which is different from the case for non-cohesive sediment in which the incipient motion is con-elated with the diameter of sand particles instead. The incipient motion occurs in two different ways depending on the concentration of mud in the bottom. For sufficiently fine particles and a concentration lower than 1.20 g/cm(3), the cohesive sediment appears as fluidized mud, and the incipient motion is in the form of instability of an internal wave. For a higher concentration, the cohesive sediment appears as general quasi-solid-mud, and the incipient motion can be described by a series of extended Shields curves each with a different porosity for newly deposited alluvial mud.
基金Project supported by the Natural Science Foundation of China (Y405038) Science and Technology Key Project of ZhejiangProvince (2006C21080)
文摘A series of Gd-doped Li-Ni ferrites with the formula of LiNi0.5GdxFe2-xO4 where x = 0.00 - 0.08 in steps of 0.02, were prepared by thermolysis of oxalate precursors obtained by rheological phase reaction. The structure, morphology, and the magnetic properties of the samples were characterized by powder X-ray diffraction (XRD), atomic force microscopy (AFM) and a vibrating sample magnetometer (VSM). A single spinel phase was obtained in the range of x = 0.00 - 0.04. The lattice parameters of the Gd-doped samples were larger than that of pure Li-Ni ferrite, and increased in the range of 0.00 ≤ x ≤ 0.04, then decreased up to x = 0.08, because of the formation of the secondary phase (Gd- FeO3). All samples were spheric particles with an average size of about 100 nm, but agglomerated to some extent. The hysteresis loops indicated that the saturation magnetization decreased gradually with increasing Gd content, while the variation of coercivity was related to the microstructure of the Gd-doped samples.
基金the National Key Technology R&D Program for the 12th Five-Year Plan of China (No. 2014BAB01B03)the National Natural Science Foundation of China (No. 51304192)
文摘It is an effective way to use coal slime as fuel for circulating fluidized bed boilers, which will not only solve its pollution to the environment, but also turn waste to treasure. In order to provide basic technical information for transportation of coal slime from the coal preparation plant to the boiler, this paper experimentally studied the rheological behaviors of coal slime produced by filter-pressing. By using a rotational viscometer, the influences of water content, temperature, and shear time on the rheological behaviors of coal slime were investigated. Experimental results show that the coal slime will behave like Bingham plastics with low water content and like Bingham pseudo-plastics with 37.5% water content,while like pseudo-plastics with 40% water content. This indicates that the water content of coal slime must be controlled in consideration of both transportation resistance and combustion efficiency. Study results also show that, the apparent viscosity of coal slime at 5℃ is about 1.5–1.7 times of that at 40℃ for water contents 32%–37.5%, while the influence of temperature can be neglected when the water content is 40%. With increasing of water content, the influences of shear time on the apparent viscosity of coal slime becomes less. When the water content is more than 30%, the effect of shear time is negligible. It indicates that water content has the most important influence on the rheological behaviors of coal slime. There must be an optimal water content in considering conveying resistance and combustion efficiency. The environmental temperature must also be considered in coal slime transportation.
基金supported by the National Natural Science Foundation of China(Grant No.41521001)the Natural Science Foundation of Hubei Province(Grant No.2018CFB385)
文摘The rheological behavior of a soft interlayer is critical to understanding slope stability, which is closely related to the water content of the soft interlayer. This study used the soft interlayer of the Permian Maokou Formation in Southwest China as an example to perform ring shear creep tests with different water content amounts. The effect of water content on the creep properties of the soft interlayer was analyzed, and a new shear rheological model was established. This research produced several findings. First, the ring shear creep deformation of the soft interlayer samples varied with the water content and the maximum instantaneous shear strain increment occurred near the saturated water content. As the water content increased, the cumulative creep increment of the samples increased. Second, the water content significantly affected the long-term strength of the soft interlayer, which decreased with the increase of water content, exhibiting a negative linear correlation. Third, a constitutive equation for the new rheological model was derived, and through fitting of the ring shear creep test data, the validity and applicability of the constitutive equation were proven. This study has developed an important foundation for studying the long-term deformation characteristics of a soft interlayer with varying water content.
基金This work was supported by the National Science Fund for Distinguished Young Scholars of China (No.50125312) andSpecial Funds for Major State Basic Research Projects (No.G1999064800).
文摘Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. 'the second plateau', appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.
基金National Key Research and Development Program of China(2017YFB0310400)National Natural Science Foundation of China(51572277,51702340)+1 种基金Shanghai Sailing Program(17YF1428800)Natural Science Foundation of Shanghai(17ZR1434800)。
文摘As for ceramic stereolithography technique,the preparation of suitable resin-based ceramic slurry is of primary importance.In this study,the effects of powder characteristics such as specific surface area,particle size and distribution,particle morphology on the rheological behavior of zirconia resin-based suspensions were investigated intensively.Results show that the specific surface area of the powder is the most important factor affecting slurry viscosity.Choosing low specific surface area and quasi-spherical shaped powder is more likely to obtain low viscosity slurries.In addition,the influence of solid loading on the flow behavior were also studied using Krieger-Dougherty model.Zirconia samples with the relative density of(97.83±0.33)%were obtained after sintering at 1550℃.No obvious abnormal grain growth in the microstructure of the sintered body is observed.Results indicate that after the optimization of the processing parameters with the help of rheology characterization,complex-shaped high-quality zirconia parts can be obtained using the stereolithography technique.
基金Supported by the National Natural Science Foundation of China(Nos.11502226,51274251,51434002)the Key Research and Development Plan of Hunan Province(No.2017WK2032)+1 种基金the Research Foundation of Education Bureau of Hunan Province,China(Nos.15C1317,16C1542)the Hunan Provincial Innovation Foundation For Postgraduate(No.CX2017B342)
文摘The traction capacity of the mining machine is greatly in?uenced by the traction rheological properties of the deep-sea sediments. The best simulative soil was prepared for substituting the deep-sea sediment based on the deep-sea sediment collected from the Paci?c C-C mining area. Traction rheological properties of the simulative soil were studied by a home-made test apparatus. In order to accurately describe the traction rheological properties and determine traction rheological parameters, the Newtonian dashpot in Maxwell body of Burgers model was replaced by a self-similarity spring-dashpot fractance and a new rheological constitutive model was deduced by fractional derivative theory. The results show the simulative soil has obvious non-attenuate rheological properties. The transient creep and stable creep rate increase with the traction, but they decrease with ground pressure. The fractional derivative Burgers model are better in describing non-attenuate rheological properties of the simulative soil than the classical Burgers model. For the new traction rheological constitutive equation of the simulative soil, the traction rheological parameters can be obtained by ?tting the tested traction creep data with the traction creep constitutive equation. The ground contact length of track and walking velocity of the mining machine predicted by the traction rheological constitutive equation can be used to take full advantages of the maximum traction provided by the soil and safely improve mining effciency.
基金This work was supported by the National Natural Science Foundation for Distinguished Young Scholars(No.50125312)Key Program of National Science Foundation of China(No.50133020)National Natural Science Foundation of China(No.50373037)
文摘The dynamic rheological measurements have been a preferred approach to the characterization of the structure and properties for multi-component or multi-phase polymer systems,due to its sensitive response to changes of structure for these heterogeneous polymers.In the present article,recent progresses in the studies on dynamic rheology for heterogeneous polymer systems including polymeric composites filled with inorganic particles,thermo-oxidized polyolefins,phase- separated polymeric blends and functional polymers with the scaling and percolation behavior are reviewed,mainly depending on the results by the authors' group.By means of rheological measurements,not only some new fingerprints responsible for the evolution of morphology and structure concerning these polymer systems are obtained,the corresponding results are also significant for the design and preparation of novel polymer-based composites and functional materials.