Anti-aging performance improvement and enhanced combustion efficiency of boron via the coating of PDA

Boron is an ambitious fuel in energetic materials since its high heat release values,but its application is prohibited by low combustion efficiency and oxidization during storage.The polydopamine(PDA)was introduced into boron particles,investigating the impact of PDA content on the energetic behavior of boron.The results indicated that the PDA coating formed a fishing net structure on the surface of boron particles.The heat release results showed that the combustion calorific value of B@PDA was higher than that of the raw boron.Specifically,the actual combustion heat of boron powder in B@10%PDA increased by 38.08%.Meanwhile,the DSC peak temperature decreased by 100.65℃under similar oxidation rate compared to raw boron.Simultaneously,the B@PDA@AP and B@AP composites were prepared,and their combustion properties were evaluated.It was demonstrated that B@10%PDA@AP exhibited superior performance in terms of peak pressure and burning time,respectively.The peak pressure is 12.43 kPa more than B@AP and burning time is 2.22 times higher than B@AP.Therefore,the coating of PDA effectively inhibits the oxidization of boron during storage and enhances the energetic behavior of boron and corresponding composites.

Direct Yaw Moment Control for Distributed Drive Electric Vehicle Handling Performance Improvement

For a distributed drive electric vehicle（DDEV） driven by four in-wheel motors, advanced vehicle dynamic control methods can be realized easily because motors can be controlled independently, quickly and precisely. And direct yaw-moment control（DYC） has been widely studied and applied to vehicle stability control. Good vehicle handling performance： quick yaw rate transient response, small overshoot, high steady yaw rate gain, etc, is required by drivers under normal conditions, which is less concerned, however. Based on the hierarchical control methodology, a novel control system using direct yaw moment control for improving handling performance of a distributed drive electric vehicle especially under normal driving conditions has been proposed. The upper-loop control system consists of two parts： a state feedback controller, which aims to realize the ideal transient response of yaw rate, with a vehicle sideslip angle observer; and a steering wheel angle feedforward controller designed to achieve a desired yaw rate steady gain. Under the restriction of the effect of poles and zeros in the closed-loop transfer function on the system response and the capacity of in-wheel motors, the integrated time and absolute error（ITAE） function is utilized as the cost function in the optimal control to calculate the ideal eigen frequency and damper coefficient of the system and obtain optimal feedback matrix and feedforward matrix. Simulations and experiments with a DDEV under multiple maneuvers are carried out and show the effectiveness of the proposed method： yaw rate rising time is reduced, steady yaw rate gain is increased, vehicle steering characteristic is close to neutral steer and drivers burdens are also reduced. The control system improves vehicle handling performance under normal conditions in both transient and steady response. State feedback control instead of model following control is introduced in the control system so that the sense of control intervention to drivers is relieved.

PERFORMANCE IMPROVEMENT OF CENTRIFUGAL FAN BY MEANS OF NUMERICAL SIMULATION

Numerical simulation is used to investigate the flow field in a model centrifugal fan for steam power stations in order to improve the performance. During testing the model fan, it is found that the efficiency is only 62.5% with inlet box, without it the efficiency is 83%. In addition, the strong vibration of test rig is observed with inlet box. It would be highly desirable if the aerodynamics of the fan could be studied. Therefore, numerical simulation is carried out to investigate the internal flow characteristics of a model fan with inlet box. The results from CFD analysis show that the whole region of the inlet box is occupied by a spiral vortex rotating inversely as the rotor＇s direction, which significantly affect the most flow＇region inside the fan. For this reason, a dummy plate is arranged in the inlet box to impede the generation of the spiral vortex, the results from CFD after the reform demonstrate that the modification is quiet effective, the former large spiral vertex has been destroyed effectively, the large one is superseded in favor of two small vortexes. However, two small vortexes have little effect on the inner flow of the rotor and the following parts. Finally, the efficiency of the model fan is improved by the test and the strong vibration of the test rig disappears. This type of modification has been used in steam power stations, the fan efficiency raises to 84% successfully.

Influencing Factors and Improvement Suggestions for Agricultural Green Development Performance:Empirical Insights from China

Agricultural green development is an essential direction for global sustainable agriculture.The academic literature,however,needs to place greater emphasis on studying the factors influencing agricultural green development performance and how such performance can be improved.A theoretical framework for agricultural green development performance was constructed in this paper using the Super-SBM model,which considers undesirable outputs,to measure the agricultural green development performance of 330 cities at or above the prefecture level in China(excluding Tibet Autonomous Region,Hong Kong,Macao and Taiwan of China)from 2007 to2018.Furthermore,the influencing mechanism of agricultural green development performance was then analyzed using a spatial econometric model.The results show that:1)from 2007 to 2018,China’s agricultural green development performance experienced three stages of evolution:‘rise,decline and rise’.2)The regions with high performance agricultural green development are mainly distributed in eastern China,northeastern China,and southern Qinghai Province.3)The agricultural economic level,industrialization process,and labor quality play significant roles in promoting local agricultural green development performance,while such performance is obviously inhibited by the openness level and the government’s environmental regulations.Local agricultural green development performance is significant inhibited by the agricultural economic level and accelerated industrialization process in neighboring cities,while significantly promoted by the agricultural industrial structure in neighboring cities.Some suggestions for improving agricultural green development performance are proposed based on these research results,which can provide scientific references for promoting sustainable agriculture.

Performance Improvement of GaN-Based Violet Laser Diodes

The influences of InGaN/GaN multiple quantum wells (MQWs) and AlGaN electron-blocking layers (EBL) on the performance of GaN-based violet laser diodes are investigated. Compared with the InGaN/GaN MQWs grown at two different temperatures, the same-temperature growth of InGaN well and GaN barrier layers has a positive effect on the threshold current and slope efficiency of laser diodes, indicating that the quality of MQWs is improved. In addition, the performance of GaN laser diodes could be further improved by increasing Al content in the AlGaN EBL due to the fact that the electron leakage current could be reduced by properly increasing the barrier height of AlGaN EBL. The violet laser diode with a peak output power of 20 W is obtained.

Performance improvement of continuous carbon nanotube fibers by acid treatment

Continuous CNT fibers have been directly fabricated in a speed of 50 m/h-400 m/h,based on an improved chemical vapor deposition method.As-prepared fibers are further post-treated by acid.According to the SEM images and Raman spectra,the acid treatment results in the compaction and surface modification of the CNTs in fibers,which are beneficial for the electron and load transfer.Compared to the HNO3 treatment,HClSO_3 or H_2SO_4 treatment is more effective for the improvement of the fibers＇ properties.After HCISO_3 treatment for 2 h,the fibers＇ strength and electrical conductivity reach up to-2 GPa and-4.3 MS/m,which are promoted by-200%and almost one order of magnitude than those without acid treatment,respectively.The load-bearing status of the CNT fibers are analyzed based on the downshifts of the G＇ band and the strain transfer factor of the fibers under tension.The results reveal that acid treatment could greatly enhance the load transfer and inter-bundle strength.With the HCISO3 treatment,the strain transfer factor is enhanced from-3.9%to-53.6%.

Comparative Analysis and Performance Improvement of Production Lines in Champion Breweries Plc and Nigerian Bottling Company

In this study,a comparative analysis of the production lines of Champion Breweries PLC and Nigerian Bottling Company was performed in order to determine ways of improving the productivity growth in Champion Breweries Plc.To achieve this aim,a bottling line model was developed and validated;studies were also carried out to ascertain the bottling line technical practices that are presently being adopted in the brewery plant.The problems affecting the smooth operation of the bottling lines were unraveled and methods of solving them have been recommended.Also,the overall equipment effectiveness(OEE)model was developed and used in the analysis in addition to other performance measurement techniques,to measure the production losses and to identify areas of process improvements.Results showed that the OEE in the existing production lines of Champion Lager Beer and Nigerian Bottling Company(Coca-Cola)is 61.5% and 62.0% respectively.Theoretical validation technique was used to validate these production lines and as a result,the validated model shows an improvement in the OEE score.The validated OEE models are 63.1% and 63.0% respectively.The adoption of the results in these validated models will definitely lead to improved productivity of both production lines.

Effects of Fleckvieh on the Performance of Dual-Purpose Cattle Improved by Hybridization with Local Beef Cows

[Objective] The paper aimed to study the improved effect of local beef cattle with Fleckvieh cattle and provide theoretical basic data for local cattle industry in central plain agricultural area in China. [Method] With 500 local beef cattle as female parents and Fleckvieh cattle as male parents,hybridization improvement was conducted via artificial insemination. The growth performance,slaughter performance,milk performance and milk components of F1 and F2 hybrids were measured. [Result] The birth body weights of F2 were significantly higher than those of local beef cow,but there was no remarkable difference between F1 and local beef cow or F1 and F2. The growth rates of F1 and F2 at different stages were higher than those of local beef cattle. The slaughter performance,such as carcass weight( P < 0. 05),dressing percentage,net meat rate( P < 0. 05),marbling score of F1 and F2 were higher than those of local beef cow. Milk production performance,such as actual milk yield,305 d corrected milk yield and 4% standard milk yield of F2 were signally higher than those of F1 and local beef cattle( P< 0. 05),and F1 was markedly higher than local beef cattle( P < 0. 05). For milk composition,although milk fat percentage,milk protein rate,lactose rate and total solids( TS) of F1 and F2 were slightly lowered compared with local beef cattle at varying degrees,they were still at high levels compared with Holstein cows.[Conclusion]Fleckvieh cattle,as a male parent,can significantly improved growth performance,slaughter performance and milk performance of offsprings. It would also increases the economic efficiency of local beef cattle by higher quality and price,as well as changing production model from beef to dual purpose of beef and milk.

Improved Performance of a Wavelength-Tunable Arrayed Waveguide Grating in Silicon on Insulator

The improved performance of a wavelength-tunable arrayed waveguide grating (AWG) is demonstrated, including the crosstalk, insertion loss and the wavelength tuning efficiency. A reduced impact of the fabrication process on the AWG is achieved by the design of bi-level tapers. The wavelength tuning of the AWG is achieved according to the thermo-optic effect of silicon, and uniform heating of the silicon waveguide layer is achieved by optimizing the heater design. The fabricated AWG shows a minimum crosstalk of 16 dB, a maximum insertion loss of 3.91 dB and a wavelength tuning efficiency of 8.92 nm/W, exhibiting a ～8 dB improvement of crosstalk, ～2.1 dB improvement of insertion loss and ～5 nm/W improvement of wavelength tuning efficiency, compared to our previous reported results.

Performance improvement of CdS/Cu(In,Ga)Se_2 solar cells after rapid thermal annealing

In this paper, we investigated the effect of rapid thermal annealing （RTA） on solar cell performance. An opto-electric conversion efficiency of 11.75% （Voc = 0.64 V, Jsc = 25.88 mA/cm2, FF=72.08%） was obtained under AM 1.5G when the cell was annealed at 300℃ for 30 s. The annealed solar cell showed an average absolute efficiency 1.5% higher than that of the as-deposited one. For the microstructure analysis and the physical phase confirmation, X-ray diffraction （XRD）, Raman spectra, front surface reflection （FSR）, internal quantum efficiency （IQE）, and X-ray photoelectron spectroscopy （XPS） were respectively applied to distinguish the causes inducing the efficiency variation. All experimental results implied that the RTA eliminated recombination centers at the p-n junction, reduced the surface optical losses, enhanced the blue response of the CdS buffer layer, and improved the ohmic contact between Mo and Cu（In, Ga）Se2 （CIGS） layers. This leaded to the improved performance of CIGS solar cell.

Improved Performance of W/HZSM-5 Catalysts for Dehydroaromatization of Methane

The dehydroaramatization of methane over W-supported ZSM-5 with varying degrees of Li+ ion-exchanged catalysts was studied with and without oxygen at 1073 K and atmospheric pressure. Catalyst activity and stability were found to be influenced by the catalyst acidity related to Bronsted acid sites and by the presence of oxygen in the feed. The NH3-TPD and FTIR-pyridine results demonstrated that partially exchanged of H+ ions by Li+ into the W/HZSM-5 catalysts could be used to control the amount of strong acid sites on the catalyst surface. Without oxygen, the 3WHLi-Z (5:1) catalyst that has strong acid sites equal to nearly 74% of the original strong acid sites in the parent HZSM-5 exhibited the highest methane conversion and selectivity towards aromatics. However, the catalyst deactivated in a five hour period. In the presence of oxygen, the catalyst activity and stability could be improved further. The results of this study revealed that a suitable amount of strong Bronsted acid sites as well as oxygen addition in the feed increased the catalyst activity and stability. The 3WHLi-Z(5:1) catalyst exhibited improved performance in the dehydroaromatization of methane.

Study on Reproductive Performance of Improved Hybrid from Chinese Holstein Cattle

In order to overcome the problems such as decline in adaptability, low fertility and few utilization years due to continuously increasing coefficient of inbreeding of Chinese Holstein cattle, three dairy-beef dual-purpose cattle varieties （purebred Simmental, Montbeliard and Fleckvieh） were introduced as the male parents to be hybridized with Chinese Holstein cattle, so as to study the improvement effect in the reproduction performance and milk production performance of the hybrid cattle. The results showed that the first-filial generation of Montbeliard had a very significant difference in gestation period from Chinese Holstein cattle （ P 〈0.01）. The parity of Fleckvieh s first-filial generation had a very significant effect on 305 d milk yield （ P 〈0.01）; and for the first-filial generation of Montbeliard, mating times and open days significantly affected 305 d milk yield （ P 〈0.05）, and its total milk yield had a significant difference from Chinese Holstein cattle （ P 〈0.05）. Comprehensively, the reproduction traits of Montbeliard s first-filial generation are better than other two varieties.

Performance Improvement in Hydrogenated Few-Layer Black Phosphorus Field-Effect Transistors

A capping layer for black phosphorus（BP） field-effect transistors（FETs） can provide effective isolation from the ambient air; however, this also brings inconvenience to the post-treatment for optimizing devices. We perform low-temperature hydrogenation on Al2 O3 capped BP FETs. The hydrogenated BP devices exhibit a pronounced improvement of mobility from 69.6 to 107.7 cm2 v-1 s-1, and a dramatic decrease of subthreshold swing from8.4 to 2.6 V/dec. Furthermore, high/low frequency capacitance-voltage measurements suggest reduced interface defects in hydrogenated BP FETs. This could be due to the passivation of interface traps at both Al2 O3/BP and BP/SiO2 interfaces with hydrogen revealed by secondary ion mass spectroscopy.

Performance Improvement of the LM Device and Its Application to Precise Measurement of Motion Trajectories within a Small Range with a Machining Centre

In order to apply the LM device previously developed to precisely measuring small motion trajectories located on the different motion planes, three major improvements are successfully performed under the condition of completely maintaining the advantages of the device. These improvements include 1) development of a novel connection mechanism to smoothly attach the device to the spindle of a machining centre;2) employment of a new data sampling method to achieve a high sampling frequency independent of the operating system of the control computer;and 3) proposal of a set-up method to conveniently install the device on the test machining centre with respect to different motion planes. Practical measurement experiment results with the improved device on a machining centre sufficiently demonstrate the effectiveness of the improvements and confirm several features including a very good response to small displacement close to the resolution of the device, high precision, repeatability and reliance. Moreover, based on the measurement results for a number of trajectories for a wide range of motion conditions, the error characteristics of small size motions are systematically discussed and the effect of the movement size and feed rate on the motion accuracy is verified for the machining centre tested.

Holonic Management Tree Technique for Performance Improvement Over Self-Similar System Structures

This paper presents the detailed definition of technique for the automation of the management of complex business systems, whether they are constituted of services and productions. The technique has been referred here for the first time as Holonic Management Tree (HMT) and has been consistently contextualized into undergoing research on technological frameworks for the management cybernetics, in which the concept of viable system represents a fundamental stance. HMT is based on the use of recursive formulas over self-similar holonic structures for the attainment of continuous performance improvement in a complex and continuously evolving process. The problem is associated to a recursive tree of self-similar structures of which in this paper we discuss the interpretation with respect to knowledge modeling domain. The basic expressions for the computation of the 2nd degree trees are provided and explained in detail by means of an example in lean management context. Moreover, this work presents and discusses the expressions that handle the implementation of the n-th degree case as a recurrent abstraction of the basic and simple 2nd degree computation.

Set Programming Method and Performance Improvement of Phase Change Random Access Memory Arrays

A novel slow-down set waveform is proposed to improve the set performance and a 1 kb phase change random access memory chip fabricated with a 13nm CMOS technology is implemented to investigate the set performance by different set programming strategies based on this new set pulse. The amplitude difference （I1 - I2） of the set pulse is proved to be a crucial parameter for set programming. We observe and analyze the cell characteristics with different I1 - I2 by means of thermal simulations and high-resolution transmission electron microscopy, which reveal that an incomplete set programming will occur when the proposed slow-down pulse is set with an improperly high I1 - I2. This will lead to an amorphous residue in the active region. We also discuss the programming method to avoid the set performance degradations.

Methods to Improve Meat Performance on Yak

To compare the quality of yak meat with that of other livestock, the growth and development of yak from birth to 48-month old were measured, slaughter tests of 6-, 24-, 48-month old were made. It can improve meat performance on yak to crossbreed with beef cattle or wild yak, to improve traditional feeding and management, etc.

Improvement of Performance of Organic Light-Emitting Diodes with Both a MoO3 Hole Injection Layer and a MoO3 Doped Hole Transport Layer

We improve the performance of organic light-emitting diodes （OLEDs） with both a MoO3 hole injection layer （HIL） and a MoO3 doped hole transport layer （HTL）, and present a systematical and comparative investigation on these devices. Compared with OLEDs with only MoO3 HIL or MoO3 doped HTL, OLEDs with both MoO3 HIL and MoO3 doped HTL show superior performance in driving voltage, power efficiency, and stability. Based on the typical NPB/Alq3 heterojunction structure, OLEDs with both MoO3 HIL and MoO3 doped HTL show a driving voltage of 5.4 V and a power efficiency of 1.41 lm/W for 1000 cd/m2, and a lifetime of around 0. 88 h with an initial luminance of 5268 cd/m2 under a constant current of 190 mA/cm2 operation in air without encapsulation. While OLEDs with only MoO3 HIL or MoO3 doped HTL show higher driving voltages of 6.4 V or 5.8 V and lower power efficiencies of 1.201m/W or 1.341m/W for 1000cd/m2, and a shorter lifetime of 0.33 or 0.60h with an initial luminance of around 5122 or 5300cd/m2 under a constant current of 200 or 216mA/cm2 operation. Our results demonstrate clearly that using both MoO3 HIL and MoO3 doped HTL is a simple and effective approach to simultaneoasly improve both the hole injection and transport efficiency, resulting from the lowered energy barrier at the anode interface and the increased hole carrier density in MoO3 doped HTL.

Research on the Pushover Methodology and the Applications on the Bridge Seismic Performance Improvement Scenarios

In this paper, we conduct research on the pushover methodology and the applications on the bridge seismic performance improvement scenarios. Bridge is an important part of the traffic lifeline engineering, and after the earthquake, if the bridge damage, that will hinder the timely disaster relief operations, increase secondary disasters, not only cause the direct or indirect losses of people＇ s life and property, also affect the post-disaster recovery and reconstruction. Therefore, seismic design of the bridges has been people＇ s attention. From the earthquake when the bridge failure mechanism and the failure process point of view, to adjust the overall layout design of bridge structure, fundamentally improve the structural seismic performance as a whole. Our research proposes the novel paradigm for the corresponding challenges that will be meaningful.

OSH star enterprise pilot scheme——a partnership approach to improve the safety performance of construction industry in Hong Kong SAR

Background: The Occupational Safety and Health Council(OSHC) is committed to improve the safety performance of the high risk construction industry.In the past three years,about 40% of the fatal accidents in the construction industry were related to Renovation,Maintenance,Alteration and Addition(RMAA).Due to the poor safety record,some of the RMAA contractors have difficulty in obtaining the Employees' Compensation Insurance(ECI) cover in the market,or if they could obtain the ECI,the premium rate would be exceedingly high.In view of this,the OSHC,the Labour Department jointly launched"OSH Star Enterprise-Pilot Scheme on Safety Accreditation for the RMAA Industry",which prompts the industry to take practicable safety measures to improve the safety of working environment and reduce occupational injuries.The program also helps the stakeholders and insurers to identify safety-conscious contractors and thereby provide them with a favourable premium rate under the Employees' Compensation Insurance Residual Scheme(ECIRS).Objectives: The OSHC launches the Pilot Scheme to improve the safety performance of the RMAA industry through providing safety training,subsidizing enterprise to purchase safety equipment and providing safety audit.We also use financial incentive to encourage RMAA enterprises to join the Pilot Scheme-for those who are accredited as "OSH Star Enterprise"could receive a premium discount from the ERIRS when obtaining the ECI.The scheme also differentiates those safety-conscious and law-abiding enterprises from the poor performers,which helps the industry and public identifying the RMAA contractors who pay attention to work safety.Methods: The Pilot Scheme targets RMAA enterprises that employ less than 50 employees in Hong Kong.A three-pronged approach is used to improve the safety performance of the RMAA industry: the Pilot Scheme provides(1) financial support for the RMAA contractors to buy a transportable temporary anchor device and full body safety harness and its anchor system;(2) safety training on RMAA work safety and safety & health supervisor course;and(3) safety audit.Results: Enterprises that successfully pass the safety audit and satisfied the Scheme requirements will be accredited as"OSH Star Enterprise",which will be valid for two years.These enterprises can also be upgraded to"OSH Gold Star Enterprise"based on their continuous improvement in safety performance.OSHC will set up a register of OSH-accredited enterprises in RMAA works for reference of the public to facilitate their choosing of accredited contractors.The Employees' Compensation Insurance Residual Scheme Bureau will provide privileged premium rate for enterprises with OSH accreditation."OSH Star Enterprise"could enjoy 40% discounts when joining their insurance scheme.For example,a skilled worker's annual premium can be reduced by about HK $ 36,000.While,the "OSH Gold Star Enterprise"could enjoy 50% discounts when joining their insurance scheme,which means a skilled worker's annual premium can be reduced up to HK $ 45,000.Achievements: This Pilot Scheme offers practical assistance as well as attractive financial incentives for the RMAA industry to improve their safety performance.The Employees'Compensation Insurance Residual Scheme provides premium discounts for enterprises that have a good safety record.It provides incentive for RMAA contractors to actively participate in the Pilot Scheme.The Scheme demonstrates that by providing a safe working environment and appropriate personal protective equipment to workers,the enterprise not only helps to reduce the accident rate of the industry but also receive an economic return.The Pilot Scheme bridges stakeholders of RMAA industry,the government and the insurance industry creating an "all-win"situation.This partnership approach to prevent injuries and accidents in the construction industry could be an effective model for other industries.