The stress state in a rock mass is complex. Stress redistribution around underground excavation may lead to various failure modes, including compressive-shear, tensile-shear, and tensile failures. The ability to perfo...The stress state in a rock mass is complex. Stress redistribution around underground excavation may lead to various failure modes, including compressive-shear, tensile-shear, and tensile failures. The ability to perform laboratory tests with these complex stress states is significant for establishing new strength criteria. The present paper introduces a new rock testing system with “tensile-compressive-shear”loading functions. The device includes bi-directional and double-range hydraulic cylinders, auxiliary loading equipment, and roller rows that can perform direct compressive-shear tests, direct tensile tests,and direct tensile-shear tests. The testing system provides maximum vertical and lateral loading forces of2000 k N and allows testing cubical rock specimens with dimensions of 0.5 m × 0.5 m × 0.5 m. The performance of the testing machine was evaluated by testing a rock-like material based on cement mortar under compressive-shear, tensile, and tensile-shear stress states. The failure process and deformation characteristics were monitored during loading using acoustic emission(AE) transient recorder,piezoelectric AE sensors, a high-speed camera, and a thermal infrared camera. The failure mechanism was investigated by analyzing AE counts, AE amplitude, strain, and temperature changes on the rock specimen surface. The test results confirmed that the testing system could successfully simulate the abovementioned stress path. The AE counts and amplitude responses were influenced by different failure modes. The temperature response during the compressive-shear test indicated the development of a high-temperature band on the rock specimen surface. In contrast, a negligible temperature change was observed during the tensile and tensile-shear tests. The newly developed multifunctional rock testing system allows laboratory tests under various failure modes. The monitoring results of multiple variables during rock failure tests provide valuable information on failure characteristics.展开更多
Spalling is a typical brittle failure phenomenon of hard rock in deep caverns under high geostress.In this study,key issues are systematically studied concerning the spalling failure of deep hard rock caverns.First,th...Spalling is a typical brittle failure phenomenon of hard rock in deep caverns under high geostress.In this study,key issues are systematically studied concerning the spalling failure of deep hard rock caverns.First,the prismatic rock specimens with small thicknesses(i.e.width×thickness×height:20 mm×50 mm×100 mm)are employed in our tests which not only successfully simulate the spalling failure of hard rock in the laboratory but also obtain a reasonable spalling strength similar to that of the rock mass.Then,a series of spalling experiments is carried out to investigate the mechanism of spalling failure of deep hard rock caverns.Our results show that the intermediate principal stress,weak dynamic disturbances,and rock microstructure have significant effects on the spalling failure.The spalling strength is approximately(0.3–0.8)UCS,where UCS is the uniaxial compressive strength of the cylindrical rock sample with a diameter of around 50 mm.The spalling strength increases first and then decreases with increasing intermediate principal stress.Moreover,an empirical spalling strength criterion and a numerical method of spalling failure are proposed.This numerical method can not only simulate the spalling failure zone formed by tangential compressive stress concentration after excavation under different intermediate principal stresses,but also successfully simulate the failure transition from tensile mode to shear mode associated with confinement change in deep hard rock caverns.Furthermore,an acoustic emission-based early warning method using neural network is proposed to predict the spalling failure.Finally,a technical roadmap for preventing and controlling spalling failure of deep hard rock caverns is presented after summarizing the successful experiences in a typical engineering case.展开更多
This investigation aims to explore the effects of stress conditions and rock cutting rates on hard rock fragmentation through indentation tests on a newly designed triaxial testing apparatus.This apparatus was designe...This investigation aims to explore the effects of stress conditions and rock cutting rates on hard rock fragmentation through indentation tests on a newly designed triaxial testing apparatus.This apparatus was designed to realize a triaxial loading and indentation test of cylindrical specimens using inserted tooth cutter.The boreability and crushing efficiency of granite rock was investigated by analyzing the change rules of the thrusting force,penetration depth,characteristics of chippings and failure patterns.Several quantitative indexes were used to evaluate rock boreability in this investigation.The granite rock samples all had a chiselled pit and a crushed rock core.Under initial stress conditions,only flat-shape chippings were stripped from the rock surface when the thrusting force reached 20 kN.The rock cutting special energy had a close correlation with the initial stress conditions and inserted tooth shape.Moreover,a thrusting force prediction model was proposed in this paper.The contribution of this study is that for the first time the influence mechanism of the initial triaxial stress conditions on rock fragmentation is investigated using an inserted tooth and the newly designed testing apparatus.This study has a crucial importance for practical underground hard rock crushing in geoengineering.展开更多
Xiangjiaba hydropowcr station is one of the complicated geological conditions of its dam foundation, parameters of rock masses are very important issues. To cascade power stations on the Jinsha River, China. Due to th...Xiangjiaba hydropowcr station is one of the complicated geological conditions of its dam foundation, parameters of rock masses are very important issues. To cascade power stations on the Jinsha River, China. Due to the evaluating the rock mass quality and determining the mechanical address these issues, several groups of rock borehole shear tests (RBSTs) were conducted on the black mudstone in the dam foundation of Xiangjiaba hydropower station in the second construction phase. Forty three groups of shear strengths of black mudstone samples were obtained from RBSTs, and the shear strength parameters (c and f) were calculated using the least squares method. In addition, the limitations and merits of RBST employed in the Xiangjiaba hydropower station were discussed. Test results indicate that the shear strength parameters obtained from RBST have a good correlation with the results from sotmd wave test in borehole. It is believed that RBST has a good adaptability and applicability in geotechnical engineering.展开更多
This paper reports in situ tension test and laboratory model test for large diameter, manually digging anchorage piles in the 2nd Luzhou Changjiang Bridge. Tension behavior, uplift bearing capacity and influenc...This paper reports in situ tension test and laboratory model test for large diameter, manually digging anchorage piles in the 2nd Luzhou Changjiang Bridge. Tension behavior, uplift bearing capacity and influence of rock characteristics on bearing capacity are discussed. Proposes are presented with respect to issues related to the construction and design of uplift piles.展开更多
Based on the similarity theory, taking the horseshoe, city-gate and round linings as examples, the value and distribution regularities of normal frost heaving pressures (hereinafter as frost heaving pressures) in tu...Based on the similarity theory, taking the horseshoe, city-gate and round linings as examples, the value and distribution regularities of normal frost heaving pressures (hereinafter as frost heaving pressures) in tunnels excavated in fractured rock mass in cold regions under different constraints and freezing depths were studied by a test model. It was found that the larger the frozen depth, the larger the frost heaving pressure, and the stronger the top constraint, the larger the frost heaving pressure. For the horseshoe lining and city-gate lining, the top constraint has a greater effect on the frost heaving pressures on the arch and the inverted arch. For the round lining, the influences of the top constraint on the frost heaving pressure in all linings are almost the same. The frost heaving pressure is maximum on the city-gate lining and minimal on the round lining. The largest frost heaving pressure all occur near the foot of the inverted arch for the three kinds of lining. Thus, the test data basically coincide with the observed in situ data.展开更多
A discrete element method (DEM) called particle flow code (PFC2D) was used to construct a model for Brazilian disc splitting test in the present study. Based on the experimental results of intact Brazilian disc of...A discrete element method (DEM) called particle flow code (PFC2D) was used to construct a model for Brazilian disc splitting test in the present study. Based on the experimental results of intact Brazilian disc of rock-like material, a set of micro-parameters in PFC2D that reflected the macro-mechanical behavior of rock-like materials were obtained. And then PFC2D was used to simulate Brazilian splitting test for jointed rock mass specimens and specimen containing a central straight notch. The effect of joint angle and notch angle on the tensile strength and failure mode of jointed rock specimens was detailed analyzed. In order to reveal the meso-mechanical mechanism of crack coalescence, displacement trend lines were applied to analyze the displacement evolution during the crack initiation and propagation. The investigated conclusions can be described as follows. (1) The tensile strength of jointed rock mass disc specimen is dependent to the joint angle. As the joint angle increases, the tensile strength of jointed rock specimen takes on a nonlinear variance. (2) The tensile strength of jointed rock mass disc specimen containing a central straight notch distributes as a function of both joint angle and notch angle. (3) Three major failure modes, i.e., pure tensile failure, shear failure and mixed tension and shear failure mode are observed in jointed rock mass disc specimens under Brazilian test. (4) The notch angle roles on crack initiation and and joint angle play important propagation characteristics of jointed rock mass disc specimen containing a central straight notch under Brazilian test.展开更多
The effect of structural discontinuities on the progressive failure process of anisotropic rocks should be paid particular attention.The crack damage stress σ_(cd),also considered as the yield strength,and the relati...The effect of structural discontinuities on the progressive failure process of anisotropic rocks should be paid particular attention.The crack damage stress σ_(cd),also considered as the yield strength,and the relationship between σ_(cd) and the uniaxial peak strength σ_(ucs) of anisotropic rocks for different orientations 8 of the isotropy planes with respect to the loading directions were investigated theoretically and experimentally.A theoretical relation of σ_(cd)/σ_(ucs) with the function of the shape parameter m was established.Additionally,uniaxial compression tests of shale samples were conducted for several inclinations θ.The test result of σ_(cd)/σ_(ucs) was close to the theoretical value for a given orientation.Furthermore,both experimental results and theoretical solutions of σ_(cd)/σ_(ucs) were independent of the inclination θ while σ_(cd) andσ_(ucs) were strongly affected by θ.The strength ratio σ_(cd)/σ_(ucs) may therefore be an intrinsic property of anisotropic rocks and could be used to predict the failure of rock samples.展开更多
Underground space utilization and exploration is an irreversible trend for promoting sustainable development especially in megacities.Geotechnical engineering safety is always one of the most important issues in all p...Underground space utilization and exploration is an irreversible trend for promoting sustainable development especially in megacities.Geotechnical engineering safety is always one of the most important issues in all phases,including planning,design, construction and operation,of the underground project.Engineering geological and hydro-geological characteristics of the foundation rock mass展开更多
Cement mortar specimens are used to simulate the fracture of rock material under uniaxial compression test, using the ultrasonic instrument measurement test process, the waveform and wave velocity results along with t...Cement mortar specimens are used to simulate the fracture of rock material under uniaxial compression test, using the ultrasonic instrument measurement test process, the waveform and wave velocity results along with the change of specimen fracture extension are obtained. Experimental results show that at 0 MPa, there are micro-defects in the specimen, leading to the irregular change of the waveform of the measuring points 4# and 5#;At 1 - 4 MPa, there is no crack on the surface of the specimen, the waveform of ultrasonic wave is stable, and the velocity of each point increases with the increase of the strain, but the measuring point increases the wave velocity when the load is applied;When the specimen surface cracks, expect the waveform of measuring point 4# and 5# change in irregularities, the measuring point 2# waveform also changes irregularly and measuring point of the wave velocity has decreased;At the crack propagation stage, ultrasonic wave also changes irregularly along with the expansion of crack, wave velocity with the increase of the strain is also obvious downward trend;When the crack penetrates the whole specimen, the waveform of each measuring point changes abnormally, the continuity is bad, the waveform is irregular and the measured wave velocity is low.展开更多
In deep geological disposal of high-level nuclear waste,one of the most important subjects is to estimate long-term stability and strength of host rock under high temperature conditions caused by radioactive decay of ...In deep geological disposal of high-level nuclear waste,one of the most important subjects is to estimate long-term stability and strength of host rock under high temperature conditions caused by radioactive decay of the waste.In this paper,some experimental researches on the thermo-mechanical characteristics of soft sedimentary rock have been presented.For this reason,a new temperature-controlled triaxial compression and creep test device,operated automatically by a computer-controlled system,whose control software has been developed by the authors,was developed to conduct the thermo-mechanical tests in different thermal loading paths,including an isothermal path.The new device is proved to be able to conduct typical thermo-mechanical element tests for soft rock.The test device and the related testing method were introduced in detail.Finally,some test results have been simulated with a thermo-elasto-viscoplastic model that was also developed by the authors.展开更多
It is claimed that the formula used for calculating the tensile strength of a disk-shaped rock specimen in the Brazilian test is not accurate, because the formula is based on the 2-dimensional elastic theory and only ...It is claimed that the formula used for calculating the tensile strength of a disk-shaped rock specimen in the Brazilian test is not accurate, because the formula is based on the 2-dimensional elastic theory and only suitable for very long or very short cylinders. The Matlab software was used to obtain the 2-dimensional distribution of stress in the rock specimen for Brazilian test. Then the 2-dimensional stress distribution in Brazilian disk was analyzed by the Marc FEM software. It can be found that the results obtained by the two software packages can verify each other. Finally, the 3-dimensional elastic stress in the specimen was calculated. The results demonstrate that the distribution of stress on the cross section of the specimen is similar to that in 2-dimension. However, the value of the stress on the cross section varies along the thickness of the specimen and the stress is bigger when getting closer to the end of the specimen. For the specimen with a height-to-diameter ratio of 1 and a Poisson's ratio of 0.25, the tensile strength calculated with the classical 2-D formula is 23.3% smaller than the real strength. Therefore, the classical 2-D formula is too conservative.展开更多
Dynamic properties of rocks are important in a variety of rock mechanics and rock engineering problems.Due to the transient nature of the loading, dynamic tests of rock materials are very different from and much more ...Dynamic properties of rocks are important in a variety of rock mechanics and rock engineering problems.Due to the transient nature of the loading, dynamic tests of rock materials are very different from and much more challenging than their static counterparts. Dynamic tests are usually conducted using the split Hopkinson bar or Kolsky bar systems, which include both split Hopkinson pressure bar(SHPB) and split Hopkinson tension bar(SHTB) systems. Signi fi cant progress has been made on the quanti fi cation of various rock dynamic properties, owing to the advances in the experimental techniques of SHPB system.This review aims to fully describe and critically assess the detailed procedures and principles of techniques for dynamic rock tests using split Hopkinson bars. The history and principles of SHPB are outlined,followed by the key loading techniques that are useful for dynamic rock tests with SHPB(i.e. pulse shaping, momentum-trap and multi-axial loading techniques). Various measurement techniques for rock tests in SHPB(i.e. X-ray micro computed tomography(CT), laser gap gauge(LGG), digital image correlation(DIC), Moiré method, caustics method, photoelastic coating method, dynamic infrared thermography) are then discussed. As the main objective of the review, various dynamic measurement techniques for rocks using SHPB are described, including dynamic rock strength measurements(i.e.dynamic compression, tension, bending and shear tests), dynamic fracture measurements(i.e. dynamic imitation and propagation fracture toughness, dynamic fracture energy and fracture velocity), and dynamic techniques for studying the in fl uences of temperature and pore water.展开更多
The suitability of five methods was discussed here,taking the typical results from in-situ load test of Renshou Mansion and Caifu Plaza in Yueyang City for example.It shows that bearing capacity can be obtained by the...The suitability of five methods was discussed here,taking the typical results from in-situ load test of Renshou Mansion and Caifu Plaza in Yueyang City for example.It shows that bearing capacity can be obtained by the proportion load and limit load from p-s curve with the first and the second point of contraflexure easily.It is recommended that the accurate value of bearing capacity can be obtained by hyperbola fitting method and minimum curvature radius method theoretically.The rebound method is clear in principle,in which the elastoplasticity characteristic is thought about.Out of consideration for the unsteadiness and unobviousness of bearing capacity from relative settlement method,it can be only adopted as reference.So bearing capacity of soft rock ground should be determined by weathering condition of soft rock and curve type.展开更多
The stability of soil-rock mixtures(SRMs) that widely distributed in slopes is of significant concern for slope safety evaluation and disaster prevention. The failure behavior of SRM slopes under surface loading condi...The stability of soil-rock mixtures(SRMs) that widely distributed in slopes is of significant concern for slope safety evaluation and disaster prevention. The failure behavior of SRM slopes under surface loading conditions was investigated through a series of centrifuge model tests considering various volumetric gravel contents. The displacement field of the slope was determined with image-based displacement system to observe the deformation of the soil and the movement of the block during loading in the tests. The test results showed that the ultimate bearing capacity and the stiffness of SRM slopes increased evidently when the volumetric block content exceeded a threshold value. Moreover, there were more evident slips around the blocks in the SRM slope. The microscopic analysis of the block motion showed that the rotation of the blocks could aggravate the deformation localization to facilitate the development of the slip surface. The high correlation between the rotation of the key blocks and the slope failure indicated that the blocks became the dominant load-bearing medium that influenced the slope failure. The blocks in the sliding body formed a chain to bear the load and change the displacement distribution of the adjacent matrix sand through the block rotation.展开更多
This paper introduces model test results of water pressure in a fault, which is located in a slope and 16 different conditions. The results show that the water pressures in fault can be expressed by a linear function,...This paper introduces model test results of water pressure in a fault, which is located in a slope and 16 different conditions. The results show that the water pressures in fault can be expressed by a linear function, which is similar to the theoretical model suggested by Hoek. Factors affecting water pressures are water level in tension crack, dip angle of fault, the height of filling materials and thickness of fault zone in sequence.展开更多
Earthquake investigations have illustrated that even code-compliant reinforced concrete frames may suffer from soft-story mechanism.This damage mode results in poor ductility and limited energy dissipation.Continuous ...Earthquake investigations have illustrated that even code-compliant reinforced concrete frames may suffer from soft-story mechanism.This damage mode results in poor ductility and limited energy dissipation.Continuous components offer alternatives that may avoid such failures.A novel infilled rocking wall frame system is proposed that takes advantage of continuous component and rocking characteristics.Previous studies have investigated similar systems that combine a reinforced concrete frame and a wall with rocking behavior used.However,a large-scale experimental study of a reinforced concrete frame combined with a rocking wall has not been reported.In this study,a seismic performance evaluation of the newly proposed infilled rocking wall frame structure was conducted through quasi-static cyclic testing.Critical joints were designed and verified.Numerical models were established and calibrated to estimate frame shear forces.The results evaluation demonstrate that an infilled rocking wall frame can effectively avoid soft-story mechanisms.Capacity and initial stiffness are greatly improved and self-centering behavior is achieved with the help of the infilled rocking wall.Drift distribution becomes more uniform with height.Concrete cracks and damage occurs in desired areas.The infilled rocking wall frame offers a promising approach to achieving seismic resilience.展开更多
Marble is a metamorphic rock, which is one of the 3 basic rock types (magmatic, sedimentary, metamorphic) forming the earth’s crust. The major characteristic sought after in a rock mass in the field for it to be expo...Marble is a metamorphic rock, which is one of the 3 basic rock types (magmatic, sedimentary, metamorphic) forming the earth’s crust. The major characteristic sought after in a rock mass in the field for it to be exportable and usable as marble is its suitability to be cut in blocks. In the process of producing marble slabs from marble blocks, the blocks are expected not to contain potentially problematic hard or weak zones and their geomechanical and chemical properties should conform to the relevant standards. Ignoring of the geological properties of the rock in the process of deciding for marble production at a marble site and determination of production location, direction and method is the most important parameter that would increase production loss. In order to reduce losses by determination of geological properties of marble, many academic studies have been conducted on the effects of water saturation, temperature, freezing and thawing on its mechanical and fracture properties. There are further studies on crack propagation in marble under stress. However, even those marble blocks that are obtained based on geological parameters may suffer serious cracks or fractures due to stresses caused by their weight and geometry. Therefore, cutting direction is of critical importance in order to minimize marble waste in the process of cutting a marble block which is brought to the inventory or processing site with cracks, cavities or fractures. Certain studies exist within such context, where the geometry of the discontinuity within a block is determined using non-destructive methods, such as ultrasonic testing, in order to determine the appropriate cutting direction. Such studies made use of ultrasonic waves to determine the physical and chemical structures of magmatic and sedimentary rocks by measuring the progress velocity of sonic waves in the rock. Said studies, however, mostly worked on sedimentary and magmatic rock specimens, focusing less on metamorphic rocks such as marble due to their anisotropic properties. Understanding the academic literature studies on marble would provide significant contribution to the reduction of production losses during the processing marble blocks in processing plants and the achievement of production efficiency levels that are within economic limits. Within such scope, this study has reviewed the past academic studies on marble, classified them under 6 categories, and comprehensively analyzed each category based on materials, testing setups, test specimens, test parameters and research techniques.展开更多
For a study of the movement and deformation of coal-rock mass and low protected seams below a stope,as well as for fracture developments and rules of evolution of permeability,we designed a plane strain model test sta...For a study of the movement and deformation of coal-rock mass and low protected seams below a stope,as well as for fracture developments and rules of evolution of permeability,we designed a plane strain model test stand to carry out model tests of similar materials in order to improve the effect of gas drainage from low protected seams and to measure the movement and deformation of coal-rock mass using a method of non-contact close-range photogrammetry.Our results show that 1) using paraffin melting to take the place of coal seam mining can satisfy the mining conditions of a protective seam;2) coal-rock mass under goafs has an upward movement after the protective seam has been mined,causing floor heaving;3) low protected seams become swollen and deformed,providing a good pressure-relief effect and causing the coal-rock mass under both sides of coal pillars to become deformed by compression and 4) the evolution of permeability of low protected seams follows the way of initial values→a slight decrease→a great increase→stability→final decrease.Simultaneously,the coefficient of air permeability increased at a decreasing rate with an increase in interlayer spacing.展开更多
基金funding support from the National Natural Science Foundation of China (Grant Nos. U1806226 and 51979154)。
文摘The stress state in a rock mass is complex. Stress redistribution around underground excavation may lead to various failure modes, including compressive-shear, tensile-shear, and tensile failures. The ability to perform laboratory tests with these complex stress states is significant for establishing new strength criteria. The present paper introduces a new rock testing system with “tensile-compressive-shear”loading functions. The device includes bi-directional and double-range hydraulic cylinders, auxiliary loading equipment, and roller rows that can perform direct compressive-shear tests, direct tensile tests,and direct tensile-shear tests. The testing system provides maximum vertical and lateral loading forces of2000 k N and allows testing cubical rock specimens with dimensions of 0.5 m × 0.5 m × 0.5 m. The performance of the testing machine was evaluated by testing a rock-like material based on cement mortar under compressive-shear, tensile, and tensile-shear stress states. The failure process and deformation characteristics were monitored during loading using acoustic emission(AE) transient recorder,piezoelectric AE sensors, a high-speed camera, and a thermal infrared camera. The failure mechanism was investigated by analyzing AE counts, AE amplitude, strain, and temperature changes on the rock specimen surface. The test results confirmed that the testing system could successfully simulate the abovementioned stress path. The AE counts and amplitude responses were influenced by different failure modes. The temperature response during the compressive-shear test indicated the development of a high-temperature band on the rock specimen surface. In contrast, a negligible temperature change was observed during the tensile and tensile-shear tests. The newly developed multifunctional rock testing system allows laboratory tests under various failure modes. The monitoring results of multiple variables during rock failure tests provide valuable information on failure characteristics.
基金The authors greatly gratefully acknowledge the financial support from the National Natural Science Foundation of China(Grant Nos.52169021 and 51869003)the Interdisciplinary Scientific Research Foundation of Guangxi University,China(Grant No.2022JCA004).
文摘Spalling is a typical brittle failure phenomenon of hard rock in deep caverns under high geostress.In this study,key issues are systematically studied concerning the spalling failure of deep hard rock caverns.First,the prismatic rock specimens with small thicknesses(i.e.width×thickness×height:20 mm×50 mm×100 mm)are employed in our tests which not only successfully simulate the spalling failure of hard rock in the laboratory but also obtain a reasonable spalling strength similar to that of the rock mass.Then,a series of spalling experiments is carried out to investigate the mechanism of spalling failure of deep hard rock caverns.Our results show that the intermediate principal stress,weak dynamic disturbances,and rock microstructure have significant effects on the spalling failure.The spalling strength is approximately(0.3–0.8)UCS,where UCS is the uniaxial compressive strength of the cylindrical rock sample with a diameter of around 50 mm.The spalling strength increases first and then decreases with increasing intermediate principal stress.Moreover,an empirical spalling strength criterion and a numerical method of spalling failure are proposed.This numerical method can not only simulate the spalling failure zone formed by tangential compressive stress concentration after excavation under different intermediate principal stresses,but also successfully simulate the failure transition from tensile mode to shear mode associated with confinement change in deep hard rock caverns.Furthermore,an acoustic emission-based early warning method using neural network is proposed to predict the spalling failure.Finally,a technical roadmap for preventing and controlling spalling failure of deep hard rock caverns is presented after summarizing the successful experiences in a typical engineering case.
基金The authors gratefully acknowledge the financial support from Natural Science Research Project of Universities in Anhui Province(No.KJ2021A0463)Scientific Research Startup Fund for introduced talents of Anhui University of Science and Technology,and Natural Science Foundation of Anhui Province(No.2108085QE208).
文摘This investigation aims to explore the effects of stress conditions and rock cutting rates on hard rock fragmentation through indentation tests on a newly designed triaxial testing apparatus.This apparatus was designed to realize a triaxial loading and indentation test of cylindrical specimens using inserted tooth cutter.The boreability and crushing efficiency of granite rock was investigated by analyzing the change rules of the thrusting force,penetration depth,characteristics of chippings and failure patterns.Several quantitative indexes were used to evaluate rock boreability in this investigation.The granite rock samples all had a chiselled pit and a crushed rock core.Under initial stress conditions,only flat-shape chippings were stripped from the rock surface when the thrusting force reached 20 kN.The rock cutting special energy had a close correlation with the initial stress conditions and inserted tooth shape.Moreover,a thrusting force prediction model was proposed in this paper.The contribution of this study is that for the first time the influence mechanism of the initial triaxial stress conditions on rock fragmentation is investigated using an inserted tooth and the newly designed testing apparatus.This study has a crucial importance for practical underground hard rock crushing in geoengineering.
基金Supported by the National Basic Research Program of China(973 Program)(2011CB013502)the Youth Special Foundation of IWHR(YJ1106)
文摘Xiangjiaba hydropowcr station is one of the complicated geological conditions of its dam foundation, parameters of rock masses are very important issues. To cascade power stations on the Jinsha River, China. Due to the evaluating the rock mass quality and determining the mechanical address these issues, several groups of rock borehole shear tests (RBSTs) were conducted on the black mudstone in the dam foundation of Xiangjiaba hydropower station in the second construction phase. Forty three groups of shear strengths of black mudstone samples were obtained from RBSTs, and the shear strength parameters (c and f) were calculated using the least squares method. In addition, the limitations and merits of RBST employed in the Xiangjiaba hydropower station were discussed. Test results indicate that the shear strength parameters obtained from RBST have a good correlation with the results from sotmd wave test in borehole. It is believed that RBST has a good adaptability and applicability in geotechnical engineering.
文摘This paper reports in situ tension test and laboratory model test for large diameter, manually digging anchorage piles in the 2nd Luzhou Changjiang Bridge. Tension behavior, uplift bearing capacity and influence of rock characteristics on bearing capacity are discussed. Proposes are presented with respect to issues related to the construction and design of uplift piles.
文摘Based on the similarity theory, taking the horseshoe, city-gate and round linings as examples, the value and distribution regularities of normal frost heaving pressures (hereinafter as frost heaving pressures) in tunnels excavated in fractured rock mass in cold regions under different constraints and freezing depths were studied by a test model. It was found that the larger the frozen depth, the larger the frost heaving pressure, and the stronger the top constraint, the larger the frost heaving pressure. For the horseshoe lining and city-gate lining, the top constraint has a greater effect on the frost heaving pressures on the arch and the inverted arch. For the round lining, the influences of the top constraint on the frost heaving pressure in all linings are almost the same. The frost heaving pressure is maximum on the city-gate lining and minimal on the round lining. The largest frost heaving pressure all occur near the foot of the inverted arch for the three kinds of lining. Thus, the test data basically coincide with the observed in situ data.
基金supported by the National Basic Research Programof China(2014CB046905)the Fundamental Research Funds for the Central Universities(China University of Mining and Technology)(2014YC10)
文摘A discrete element method (DEM) called particle flow code (PFC2D) was used to construct a model for Brazilian disc splitting test in the present study. Based on the experimental results of intact Brazilian disc of rock-like material, a set of micro-parameters in PFC2D that reflected the macro-mechanical behavior of rock-like materials were obtained. And then PFC2D was used to simulate Brazilian splitting test for jointed rock mass specimens and specimen containing a central straight notch. The effect of joint angle and notch angle on the tensile strength and failure mode of jointed rock specimens was detailed analyzed. In order to reveal the meso-mechanical mechanism of crack coalescence, displacement trend lines were applied to analyze the displacement evolution during the crack initiation and propagation. The investigated conclusions can be described as follows. (1) The tensile strength of jointed rock mass disc specimen is dependent to the joint angle. As the joint angle increases, the tensile strength of jointed rock specimen takes on a nonlinear variance. (2) The tensile strength of jointed rock mass disc specimen containing a central straight notch distributes as a function of both joint angle and notch angle. (3) Three major failure modes, i.e., pure tensile failure, shear failure and mixed tension and shear failure mode are observed in jointed rock mass disc specimens under Brazilian test. (4) The notch angle roles on crack initiation and and joint angle play important propagation characteristics of jointed rock mass disc specimen containing a central straight notch under Brazilian test.
基金supported by the Strategic Priority Research Program of the Chinese Academy of Sciences (No.XDB10030302)the National Natural Science Foundation of China (No.41302233)the Project funded by China Postdoctoral Science Foundation (No.2014T70121)
文摘The effect of structural discontinuities on the progressive failure process of anisotropic rocks should be paid particular attention.The crack damage stress σ_(cd),also considered as the yield strength,and the relationship between σ_(cd) and the uniaxial peak strength σ_(ucs) of anisotropic rocks for different orientations 8 of the isotropy planes with respect to the loading directions were investigated theoretically and experimentally.A theoretical relation of σ_(cd)/σ_(ucs) with the function of the shape parameter m was established.Additionally,uniaxial compression tests of shale samples were conducted for several inclinations θ.The test result of σ_(cd)/σ_(ucs) was close to the theoretical value for a given orientation.Furthermore,both experimental results and theoretical solutions of σ_(cd)/σ_(ucs) were independent of the inclination θ while σ_(cd) andσ_(ucs) were strongly affected by θ.The strength ratio σ_(cd)/σ_(ucs) may therefore be an intrinsic property of anisotropic rocks and could be used to predict the failure of rock samples.
文摘Underground space utilization and exploration is an irreversible trend for promoting sustainable development especially in megacities.Geotechnical engineering safety is always one of the most important issues in all phases,including planning,design, construction and operation,of the underground project.Engineering geological and hydro-geological characteristics of the foundation rock mass
文摘Cement mortar specimens are used to simulate the fracture of rock material under uniaxial compression test, using the ultrasonic instrument measurement test process, the waveform and wave velocity results along with the change of specimen fracture extension are obtained. Experimental results show that at 0 MPa, there are micro-defects in the specimen, leading to the irregular change of the waveform of the measuring points 4# and 5#;At 1 - 4 MPa, there is no crack on the surface of the specimen, the waveform of ultrasonic wave is stable, and the velocity of each point increases with the increase of the strain, but the measuring point increases the wave velocity when the load is applied;When the specimen surface cracks, expect the waveform of measuring point 4# and 5# change in irregularities, the measuring point 2# waveform also changes irregularly and measuring point of the wave velocity has decreased;At the crack propagation stage, ultrasonic wave also changes irregularly along with the expansion of crack, wave velocity with the increase of the strain is also obvious downward trend;When the crack penetrates the whole specimen, the waveform of each measuring point changes abnormally, the continuity is bad, the waveform is irregular and the measured wave velocity is low.
文摘In deep geological disposal of high-level nuclear waste,one of the most important subjects is to estimate long-term stability and strength of host rock under high temperature conditions caused by radioactive decay of the waste.In this paper,some experimental researches on the thermo-mechanical characteristics of soft sedimentary rock have been presented.For this reason,a new temperature-controlled triaxial compression and creep test device,operated automatically by a computer-controlled system,whose control software has been developed by the authors,was developed to conduct the thermo-mechanical tests in different thermal loading paths,including an isothermal path.The new device is proved to be able to conduct typical thermo-mechanical element tests for soft rock.The test device and the related testing method were introduced in detail.Finally,some test results have been simulated with a thermo-elasto-viscoplastic model that was also developed by the authors.
基金[This work was financially supported by the Fundamental Science Research Fund of Southwest Jiaotong University (No.2004B13).
文摘It is claimed that the formula used for calculating the tensile strength of a disk-shaped rock specimen in the Brazilian test is not accurate, because the formula is based on the 2-dimensional elastic theory and only suitable for very long or very short cylinders. The Matlab software was used to obtain the 2-dimensional distribution of stress in the rock specimen for Brazilian test. Then the 2-dimensional stress distribution in Brazilian disk was analyzed by the Marc FEM software. It can be found that the results obtained by the two software packages can verify each other. Finally, the 3-dimensional elastic stress in the specimen was calculated. The results demonstrate that the distribution of stress on the cross section of the specimen is similar to that in 2-dimension. However, the value of the stress on the cross section varies along the thickness of the specimen and the stress is bigger when getting closer to the end of the specimen. For the specimen with a height-to-diameter ratio of 1 and a Poisson's ratio of 0.25, the tensile strength calculated with the classical 2-D formula is 23.3% smaller than the real strength. Therefore, the classical 2-D formula is too conservative.
基金support by the Natural Sciences and Engineering Research Council of Canada (NSERC) through the Discovery Grant No. 72031326
文摘Dynamic properties of rocks are important in a variety of rock mechanics and rock engineering problems.Due to the transient nature of the loading, dynamic tests of rock materials are very different from and much more challenging than their static counterparts. Dynamic tests are usually conducted using the split Hopkinson bar or Kolsky bar systems, which include both split Hopkinson pressure bar(SHPB) and split Hopkinson tension bar(SHTB) systems. Signi fi cant progress has been made on the quanti fi cation of various rock dynamic properties, owing to the advances in the experimental techniques of SHPB system.This review aims to fully describe and critically assess the detailed procedures and principles of techniques for dynamic rock tests using split Hopkinson bars. The history and principles of SHPB are outlined,followed by the key loading techniques that are useful for dynamic rock tests with SHPB(i.e. pulse shaping, momentum-trap and multi-axial loading techniques). Various measurement techniques for rock tests in SHPB(i.e. X-ray micro computed tomography(CT), laser gap gauge(LGG), digital image correlation(DIC), Moiré method, caustics method, photoelastic coating method, dynamic infrared thermography) are then discussed. As the main objective of the review, various dynamic measurement techniques for rocks using SHPB are described, including dynamic rock strength measurements(i.e.dynamic compression, tension, bending and shear tests), dynamic fracture measurements(i.e. dynamic imitation and propagation fracture toughness, dynamic fracture energy and fracture velocity), and dynamic techniques for studying the in fl uences of temperature and pore water.
基金National Natural Science Foundation of China(No.50874043)Scientific Research Fund of Hunan Province Education Department(No.09A028)Scientific Research Foundation for Returned Scholars,Ministry of Education of China(No.[2007]1108)
文摘The suitability of five methods was discussed here,taking the typical results from in-situ load test of Renshou Mansion and Caifu Plaza in Yueyang City for example.It shows that bearing capacity can be obtained by the proportion load and limit load from p-s curve with the first and the second point of contraflexure easily.It is recommended that the accurate value of bearing capacity can be obtained by hyperbola fitting method and minimum curvature radius method theoretically.The rebound method is clear in principle,in which the elastoplasticity characteristic is thought about.Out of consideration for the unsteadiness and unobviousness of bearing capacity from relative settlement method,it can be only adopted as reference.So bearing capacity of soft rock ground should be determined by weathering condition of soft rock and curve type.
基金supported by National Key R&D Program of China(2018YFC1508503)
文摘The stability of soil-rock mixtures(SRMs) that widely distributed in slopes is of significant concern for slope safety evaluation and disaster prevention. The failure behavior of SRM slopes under surface loading conditions was investigated through a series of centrifuge model tests considering various volumetric gravel contents. The displacement field of the slope was determined with image-based displacement system to observe the deformation of the soil and the movement of the block during loading in the tests. The test results showed that the ultimate bearing capacity and the stiffness of SRM slopes increased evidently when the volumetric block content exceeded a threshold value. Moreover, there were more evident slips around the blocks in the SRM slope. The microscopic analysis of the block motion showed that the rotation of the blocks could aggravate the deformation localization to facilitate the development of the slip surface. The high correlation between the rotation of the key blocks and the slope failure indicated that the blocks became the dominant load-bearing medium that influenced the slope failure. The blocks in the sliding body formed a chain to bear the load and change the displacement distribution of the adjacent matrix sand through the block rotation.
基金This paper is supported by the Research Fund for the Doctoral Program of Higher Education of China.
文摘This paper introduces model test results of water pressure in a fault, which is located in a slope and 16 different conditions. The results show that the water pressures in fault can be expressed by a linear function, which is similar to the theoretical model suggested by Hoek. Factors affecting water pressures are water level in tension crack, dip angle of fault, the height of filling materials and thickness of fault zone in sequence.
基金Natural Science Foundation of China under Grant Nos.51178342 and 51578314
文摘Earthquake investigations have illustrated that even code-compliant reinforced concrete frames may suffer from soft-story mechanism.This damage mode results in poor ductility and limited energy dissipation.Continuous components offer alternatives that may avoid such failures.A novel infilled rocking wall frame system is proposed that takes advantage of continuous component and rocking characteristics.Previous studies have investigated similar systems that combine a reinforced concrete frame and a wall with rocking behavior used.However,a large-scale experimental study of a reinforced concrete frame combined with a rocking wall has not been reported.In this study,a seismic performance evaluation of the newly proposed infilled rocking wall frame structure was conducted through quasi-static cyclic testing.Critical joints were designed and verified.Numerical models were established and calibrated to estimate frame shear forces.The results evaluation demonstrate that an infilled rocking wall frame can effectively avoid soft-story mechanisms.Capacity and initial stiffness are greatly improved and self-centering behavior is achieved with the help of the infilled rocking wall.Drift distribution becomes more uniform with height.Concrete cracks and damage occurs in desired areas.The infilled rocking wall frame offers a promising approach to achieving seismic resilience.
文摘Marble is a metamorphic rock, which is one of the 3 basic rock types (magmatic, sedimentary, metamorphic) forming the earth’s crust. The major characteristic sought after in a rock mass in the field for it to be exportable and usable as marble is its suitability to be cut in blocks. In the process of producing marble slabs from marble blocks, the blocks are expected not to contain potentially problematic hard or weak zones and their geomechanical and chemical properties should conform to the relevant standards. Ignoring of the geological properties of the rock in the process of deciding for marble production at a marble site and determination of production location, direction and method is the most important parameter that would increase production loss. In order to reduce losses by determination of geological properties of marble, many academic studies have been conducted on the effects of water saturation, temperature, freezing and thawing on its mechanical and fracture properties. There are further studies on crack propagation in marble under stress. However, even those marble blocks that are obtained based on geological parameters may suffer serious cracks or fractures due to stresses caused by their weight and geometry. Therefore, cutting direction is of critical importance in order to minimize marble waste in the process of cutting a marble block which is brought to the inventory or processing site with cracks, cavities or fractures. Certain studies exist within such context, where the geometry of the discontinuity within a block is determined using non-destructive methods, such as ultrasonic testing, in order to determine the appropriate cutting direction. Such studies made use of ultrasonic waves to determine the physical and chemical structures of magmatic and sedimentary rocks by measuring the progress velocity of sonic waves in the rock. Said studies, however, mostly worked on sedimentary and magmatic rock specimens, focusing less on metamorphic rocks such as marble due to their anisotropic properties. Understanding the academic literature studies on marble would provide significant contribution to the reduction of production losses during the processing marble blocks in processing plants and the achievement of production efficiency levels that are within economic limits. Within such scope, this study has reviewed the past academic studies on marble, classified them under 6 categories, and comprehensively analyzed each category based on materials, testing setups, test specimens, test parameters and research techniques.
基金the Major Programs of the National Basic Research Program of China (No.2005CB221503)the National Natural Science Foundation of China (Nos. 70533050 and 50674089) for their support of this project
文摘For a study of the movement and deformation of coal-rock mass and low protected seams below a stope,as well as for fracture developments and rules of evolution of permeability,we designed a plane strain model test stand to carry out model tests of similar materials in order to improve the effect of gas drainage from low protected seams and to measure the movement and deformation of coal-rock mass using a method of non-contact close-range photogrammetry.Our results show that 1) using paraffin melting to take the place of coal seam mining can satisfy the mining conditions of a protective seam;2) coal-rock mass under goafs has an upward movement after the protective seam has been mined,causing floor heaving;3) low protected seams become swollen and deformed,providing a good pressure-relief effect and causing the coal-rock mass under both sides of coal pillars to become deformed by compression and 4) the evolution of permeability of low protected seams follows the way of initial values→a slight decrease→a great increase→stability→final decrease.Simultaneously,the coefficient of air permeability increased at a decreasing rate with an increase in interlayer spacing.