Rapid and stable calcium-looping solar thermochemical energy storage via co-doping binary sulfate and Al–Mn–Fe oxides

Solar thermochemical energy storage based on calcium looping(CaL)process is a promising technology for next-generation concentrated solar power(CSP)systems.However,conventional calcium carbonate(CaCO_(3))pellets suffer from slow reaction kinetics,poor stability,and low solar absorptance.Here,we successfully realized high power density and highly stable solar thermochemical energy storage/release by synergistically accelerating energy storage/release via binary sulfate and promoting cycle stability,mechanical strength,and solar absorptance via Al–Mn–Fe oxides.The energy storage density of proposed CaCO_(3)pellets is still as high as 1455 kJ kg^(-1)with only a slight decay rate of 4.91%over 100 cycles,which is higher than that of state-of-the-art pellets in the literature,in stark contrast to 69.9%of pure CaCO_(3)pellets over 35 cycles.Compared with pure CaCO_(3),the energy storage power density or decomposition rate is improved by 120%due to lower activation energy and promotion of Ca^(2+)diffusion by binary sulfate.The energy release or carbonation rate rises by 10%because of high O^(2-)transport ability of molten binary sulfate.Benefiting from fast energy storage/release rate and high solar absorptance,thermochemical energy storage efficiency is enhanced by more than 50%under direct solar irradiation.This work paves the way for application of direct solar thermochemical energy storage techniques via achieving fast energy storage/release rate,high energy density,good cyclic stability,and high solar absorptance simultaneously.

Mn-doped SrCoO_(3-δ) Perovskite Oxides for Ethylene Production via Chemical Looping Oxidative Dehydrogenation of Ethane

Chemical looping oxidative dehydrogenation (CL-ODH) is an economically promising method for convertingethane into higher value-added ethylene utilizing lattice oxygen in redox catalysts, also known as oxygen carriers. Inthis study, perovskite-type oxide SrCoO_(3-δ) and B-site Mn ion-doped oxygen carriers (SrCo_(1-x)MnxO_(3-δ), x=0.1, 0.2, 0.3)were prepared and tested for the CL-ODH of ethane. The oxygen-deficient perovskite SrCoO_(3-δ) exhibited high ethyleneselectivity of up to 96.7% due to its unique oxygen vacancies and lattice oxygen migration rates. However, its low ethyleneyield limits its application in the CL-ODH of ethane. Mn doping promoted the reducibility of SrCoO_(3-δ) oxygen carriers,thereby improving ethane conversion and ethylene yield, as demonstrated by characterization and evaluation experiments.X-ray diffraction results confirmed the doping of Mn into the lattice of SrCoO_(3-δ), while X-ray photoelectron spectroscopy(XPS) indicated an increase in lattice oxygen ratio upon incorporation of Mn into the SrCoO_(3-δ) lattice. Additionally, H2temperature-programmed reduction (H2-TPR) tests revealed more peaks at lower temperature reduction zones and a declinein peak positions at higher temperatures. Among the four tested oxygen carriers, SrCo0.8Mn0.2O_(3-δ) exhibited satisfactoryperformance with an ethylene yield of 50% at 710 °C and good stability over 20 redox cycles. The synergistic effect of Mnplays a key role in increasing ethylene yields of SrCoO_(3-δ) oxygen carriers. Accordingly, SrCo0.8Mn0.2O_(3-δ) shows promisingpotential for the efficient production of ethylene from ethane via CL-ODH.

Optimizing the sulfur-resistance and activity of perovskite oxygen carrier for chemical looping dry reforming of methane

Perovskite oxides has been attracted much attention as high-performance oxygen carriers for chemical looping reforming of methane,but they are easily inactivated by the presence of trace H_(2)S.Here,we propose to modulate both the activity and resistance to sulfur poisoning by dual substitution of Mo and Ni ions with the Fe-sites of LaFeO_(3)perovskite.It is found that partial substitution of Ni for Fe substantially improves the activity of LaFeO_(3)perovskite,while Ni particles prefer to grow and react with H_(2)S during the long-term successive redox process,resulting in the deactivation of oxygen carriers.With the presence of Mo in LaNi_(0.05)Fe_(0.95)O_(3−σ)perovskite,H_(2)S preferentially reacts with Mo to generate MoS_(2),and then the CO_(2)oxidation can regenerate Mo via removing sulfur.In addition,Mo can inhibit the accumulation and growth of Ni,which helps to improve the redox stability of oxygen carriers.The LaNi_(0.05)Mo_(0.07)Fe_(0.88)O_(3−σ)oxygen carrier exhibits stable and excellent performance,with the CH_(4)conversion higher than 90%during the 50 redox cycles in the presence of 50 ppm H_(2)S at 800℃.This work highlights a synergistic effect in the perovskite oxides induced by dual substitution of different cations for the development of high-performance oxygen carriers with excellent sulfur tolerance.

Chemical looping reforming of the micromolecular component from biomass pyrolysis via Fe_(2)O_(3)@SBA-16

To solve the problems of low gasification efficiency and high tar content caused by solid–solid contact between biomass and oxygen carrier in traditional biomass chemical looping gasification process.The decoupling strategy was adopted to decouple the biomass gasification process,and the composite oxygen carrier was prepared by embedding Fe_(2)O_(3) in molecular sieve SBA-16 for the chemical looping reforming process of pyrolysis micromolecular model compound methane,which was expected to realize the directional reforming of pyrolysis volatiles to prepare hydrogen-rich syngas.Thermodynamic analysis of the reaction system was carried out based on the Gibbs free energy minimization method,and the reforming performance was evaluated by a fixed bed reactor,and the kinetic parameters were solved based on the gas–solid reaction model.Thermodynamic analysis verified the feasibility of the reaction and provided theoretical guidance for experimental design.The experimental results showed that the reaction performance of Fe_(2)O_(3)@SBA-16 was compared with that of pure Fe_(2)O_(3) and Fe_(2)O_(3)@SBA-15,and the syngas yield was increased by 55.3%and 20.7%respectively,and it had good cycle stability.Kinetic analysis showed that the kinetic model changed from three-dimensional diffusion to first-order reaction with the increase of temperature.The activation energy was 192.79 kJ/mol by fitting.This paper provides basic data for the directional preparation of hydrogen-rich syngas from biomass and the design of oxygen carriers for pyrolysis of all-component chemical looping reforming.

Ethane Chemical Looping Oxidative Dehydrogenation to Ethylene over Co_(2)O_(3)(Fe_(2)O_(3),NiO)/LaCoO_(3) Oxygen Carriers

Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for converting ethane to ethylene.In the current study MeO/LaCoO_(3)(MeO=Fe_(2)O_(3),NiO or Co_(2)O_(3))composite metal oxides were prepared via citrate gel and impregnation methods,and used as oxygen carriers for CL-ODH.X-ray diffraction results indicated that all oxygen carriers had a perovskite structure even after eight redox cycles.Under a reaction temperature of 650°C,a reaction pressure of 0.1 MPa,and a weight hourly space velocity(WHSV)of 7500 mL/(g·h),ethane conversion over Co_(2)O_(3)/LaCoO_(3) reached 100%and ethylene selectivity reached 60%,both of which were better than corresponding values attained over Fe_(2)O_(3)/LaCoO_(3) and NiO/LaCoO_(3).Ethylene selectivity remained stable for 80 cycles over Co_(2)O_(3)/LaCoO_(3),then decreased gradually after 80 cycles.X-ray photoelectron spectroscopy results and evaluation results indicated that lattice oxygen and O_(2)2-had a direct relationship with ethane conversion and ethylene selectivity.Co_(2)O_(3)/LaCoO_(3) exhibited a strong capacity to release and absorb oxygen,mainly due to interaction between Co_(2)O_(3) and LaCoO_(3).

Unraveling the atomic interdiffusion mechanism of NiFe_(2_)O_(4) oxygen carriers during chemical looping CO_(2) conversion

By employing metal oxides as oxygen carriers,chemical looping demonstrates its effectiveness in transferring oxygen between reduction and oxidation environments to partially oxidize fuels into syngas and convert CO_(2) into CO.Generally,NiFe_(2_)O_(4) oxygen carriers have demonstrated remarkable efficiency in chemical looping CO_(2) conversion.Nevertheless,the intricate process of atomic migration and evolution within the internal structure of bimetallic oxygen carriers during continuous high‐temperature redox cycling remains unclear.Consequently,the lack of a fundamental understanding of the complex ionic migration and oxygen transfer associated with energy conversion processes hampers the design of high‐performance oxygen carriers.Thus,in this study,we employed in situ characterization techniques and theoretical calculations to investigate the ion migration behavior and structural evolution in the bulk of NiFe_(2_)O_(4) oxygen carriers during H_(2) reduction and CO_(2)/lab air oxidation cycles.We discovered that during the H_(2) reduction step,lattice oxygen rapidly migrates to vacancy layers to replenish consumed active oxygen species,while Ni leaches from the material and migrates to the surface.During the CO_(2) splitting step,Ni migrates toward the core of the bimetallic oxygen carrier,forming Fe–Ni alloys.During the air oxidation step,Fe–Ni migrates outward,creating a hollow structure owing to the Kirkendall effect triggered by the swift transfer of lattice oxygen.The metal atom migration paths depend on the oxygen transfer rates.These discoveries highlight the significance of regulating the release–recovery rate of lattice oxygen to uphold the structures and reactivity of oxygen carriers.This work offers a comprehensive understanding of the oxidation/reduction‐driven atomic interdiffusion behavior of bimetallic oxygen carriers.

CO_(2)capture costs of chemical looping combustion of biomass:A comparison of natural and synthetic oxygen carrier

Chemical looping combustion has the potential to be an efficient and low-cost technology capable of contributing to the reduction of the atmospheric concentration of CO_(2) in order to reach the 1.5/2°C goal and mitigate climate change.In this process,a metal oxide is used as oxygen carrier in a dual fluidized bed to generate clean CO_(2) via combustion of biomass.Most commonly,natural ores or synthetic materials are used as oxygen carrier whereas both must meet special requirements for the conversion of solid fuels.Synthetic oxygen carriers are characterized by higher reactivity at the expense of higher costs versus the lower-cost natural ores.To determine the viability of both possibilities,a techno-economic comparison of a synthetic material based on manganese,iron,and copper to the natural ore ilmenite was conducted.The synthetic oxygen carrier was characterized and tested in a pilot plant,where high combustion efficiencies up to 98.4%and carbon capture rates up to 98.5%were reached.The techno-economic assessment resulted in CO_(2) capture costs of 75 and 40€/tCO_(2) for the synthetic and natural ore route respectively,whereas a sensitivity analysis showed the high impact of production costs and attrition rates of the synthetic material.The synthetic oxygen carrier could break even with the natural ore in case of lower production costs and attrition rates,which could be reached by adapting the production process and recycling material.By comparison to state-of-the-art technologies,it is demonstrated that both routes are viable and the capture cost of CO_(2) could be reduced by implementing the chemical looping combustion technology.

Advancements in biomass gasification research utilizing iron-based oxygen carriers in chemical looping:A review

Biomass,recognized as renewable green coal,is pivotal for energy conservation,emission reduction,and dualcarbon objectives.Chemical looping gasification,an innovative technology,aims to enhance biomass utilization efficiency.Using metal oxides as oxygen carriers regulates the oxygen-to-fuel ratio to optimize synthesis product yields.This review examines various oxygen carriers and their roles in chemical looping biomass gasification,including natural iron ore types,industrial by-products,cerium oxide-based carriers,and core-shell structures.The catalytic,kinetic,and phase transfer properties of iron-based oxygen carriers are analyzed,and their catalytic cracking capabilities are explored.Molecular interactions are elucidated and system performance is optimized by providing insights into chemical looping reaction mechanisms and strategies to improve carrier efficiency,along with discussing advanced techniques such as density functional theory(DFT)and reactive force field(ReaxFF)molecular dynamics(MD).This paper serves as a roadmap for advancing chemical looping gasification towards sustainable energy goals.

NiO-Doped Fe_(2)O_(3)/MgO Properties for the Chemical Looping Oxidative Dehydrogenation of Ethane

Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for ethylene preparation.Fe_(2)O_(3)/MgO oxygen carrier was prepared using the co-precipitation method.The influence of added NiO and its different loadings on Fe_(2)O_(3)/MgO were investigated.Then,a series of oxygen carriers were applied in the CL-ODH of the ethane cycle system.Brunauer-Emmett-Teller(BET),X-ray diffractometry(XRD),X-ray photoelection spectroscopy(XPS),and H2-temperature programmed reduction(TPR)were used to characterize the physicochemical properties of these oxygen carriers.It was confirmed that an interaction between NiO and Fe_(2)O_(3) occurred based on the XPS and H2-TPR results.Based on the CL-ODH activity performance tests conducted in a fixed-bed reactor,it was revealed that ethylene selectivity was significantly improved after NiO addition.Fe_(2)O_(3)-10%NiO/MgO showed the best activity performance with 93%ethane conversion and 50%ethylene selectivity at a reaction temperature of 650℃,atmospheric pressure,and space velocity of 7500 mL/(g·h).

Effect of sulfation during carbonation on CO_2 capture in calcium looping cycle

Abstract： Two Canadian limestones with different properties were tested to determine the effect of SO2 during the carbonation of sorbent on the CO2 capture performance in Ca- looping. When the reaction gas is mixed with SO2, the carbonation ratio of the sorbent is always lower than that without SO2 for each cycle under the same conditions, and the sulfation ratio increases almost linearly with the increase in the cycle times. At 650 ℃, there is little difference in the carbonation ratio of the sorbent during the first four cycles for the two carbonation time, 5 and 10 rain at 0. 18% SO2. The indirect sulfation reaction that occurs simultaneously with the carbonation of CaO is responsible for the degradation of the sorbent for CO2 capture, and the carbonation duration is not the main factor that affects the ability of the sorbent. 680℃ is the best carbonation temperature among the three tested temperatures and the highest carbonation ratio can be obtained. Also, the sulfation ratio is the highest. The probable cause is the different effects of temperature on the carbonation rate and sulfation rate. A higher SO2 concentration will decrease the carbonation ratio clearly, but the decrease in the carbonation capability of the sorbent is not proportional to the increase of the SO2 concentration in flue gases.

Application of Fe_2O_3/Al_2O_3 Composite Particles as Oxygen Carrier of Chemical Looping Combustion

Chemical looping combustion （CLC） of carbonaceous compounds has been proposed, in the past decade, as an efficient method for CO2 capture without cost of extra energy penalties. The technique involves the use of a metal oxide as an oxygen carrier that transfers oxygen from combustion air to fuels. The combustion is carried out in a two-step process： in the fuel reactor, the fuel is oxidized by a metal oxide, and in the air reactor, the reduced metal is oxidized back to the original phase. The use of iron oxide as an oxygen carrier has been investigated in this article. Particles composed of 80 wt% Fe2O3, together with Al2O3 as binder, have been prepared by impregnation methods. X-ray diffraction （XRD） analysis reveals that Fe2O3 does not interact with the Al2O3 binder after multi-cycles. The reactivity of the oxygen carrier particles has been studied in twenty-cycle reduction-oxidation tests in a thermal gravimetrical analysis （TGA） reactor. The components in the outlet gas have been analyzed. It has been observed that about 85% of CH4 converted to CO2 and H2O during most of the reduction periods. The oxygen carrier has kept quite a high reactivity in the twenty-cycle reactions. In the first twenty reaction cycles, the reaction rates became slightly higher with the number of cyclic reactions increasing, which was confirmed by the scanning electron microscopy （SEM） test results. The SEM analysis revealed that the pore size inside the particle had been enlarged by the thermal stress during the reaction, which was favorable for diffusion of the gaseous reactants into the particles. The experimental results suggested that the Fe2O3/Al2O3 oxygen carrier was a promising candidate for a CLC system.

Detection of cyclonic eddy generated by looping tropical cyclone in the northern South China Sea: a case study

A case study on the cyclonic eddy generated by the tropical cyclone looping over the northern South China Sea (NSCS) is presented, using TOPEX/POSEIDON altimeter data and AVHRR sea surface temperature (SST) data. Three cases relating to the tropical cyclone events (Typhoon Kai-Tak in July 2000, Tropical Storm Russ in June 1994 and Tropical Storm Maria in August-September 2000) over the NSCS have been analyzed. For each looping tropical cyclone case, the cyclonic eddy with an obvious sea level depression appears in the sea area where the tropical cyclone takes a loop form, and lasts for about 2 weeks with a slight variation in location. The cold core with the SST difference greater than 2℃against its surrounding areas is also observed by the satellite-derived SST data.

Different oxidation routes for lattice oxygen recovery of double-perovskite type oxides LaSrFeCoO6 as oxygen carriers for chemical looping steam methane reforming

Double-perovskite type oxide LaSrFeCoO（LSFCO） was used as oxygen carrier for chemical looping steam methane reforming（CL-SMR） due to its unique structure and reactivity. Two different oxidation routes,steam-oxidation and steam-air-stepwise-oxidation, were applied to investigate the recovery behaviors of the lattice oxygen in the oxygen carrier. The characterizations of the oxide were determined by X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, hydrogen temperature-programmed reduction（H-TPR） and scanning electron microscopy（SEM）. The fresh sample LSFCO exhibits a monocrystalline perovskite structure with cubic symmetry and high crystallinity, except for a little impurity phase due to the antisite defect of Fe/Co disorder. The deconvolution distribution of XPS patterns indicated that Co,and Fe are predominantly in an oxidized state(Feand Fe) and(Coand Co), while O 1s exists at three species of lattice oxygen, chemisorbed oxygen and physical adsorbed oxygen. The double perovskite structure and chemical composition recover to the original state after the steam and air oxidation, while the Co ion cannot incorporate into the double perovskite structure and thus form the CoO just via individual steam oxidation. In comparison to the two different oxidation routes, the sample obtained by steam-oxidation exhibits even higher CHconversion, CO and Hselectivity and stronger hydrogen generation capacity.

Effect of Gasifying Medium on the Coal Chemical Looping Gasification with CaSO_4 as Oxygen Carrier

The chemical looping gasification uses an oxygen carrier for solid fuel gasification by supplying insufficient lattice oxygen. The effect of gasifying medium on the coal chemical looping gasification with Ca SO4 as oxygen carrier is investigated in this paper. The thermodynamical analysis indicates that the addition of steam and CO2 into the system can reduce the reaction temperature, at which the concentration of syngas reaches its maximum value.Experimental result in thermogravimetric analyzer and a fixed-bed reactor shows that the mixture sample goes through three stages, drying stage, pyrolysis stage and chemical looping gasification stage, with the temperature for three different gaseous media. The peak fitting and isoconversional methods are used to determine the reaction mechanism of the complex reactions in the chemical looping gasification process. It demonstrates that the gasifying medium(steam or CO2) boosts the chemical looping process by reducing the activation energy in the overall reaction and gasification reactions of coal char. However, the mechanism using steam as the gasifying medium differs from that using CO2. With steam as the gasifying medium, parallel reactions occur in the beginning stage, followed by a limiting stage shifting from a kinetic to a diffusion regime. It is opposite to the reaction mechanism with CO2 as the gasifying medium.

Solar chemical looping reforming of methane combined with isothermal H2O/CO2 splitting using ceria oxygen carrier for syngas production

The chemical looping reforming of methane through the nonstoichiometric ceria redox cycle(CeO2/CeO2-δ) has been experimentally investigated in a directly irradiated solar reactor to convert both solar energy and methane to syngas in the temperature range 900–1050 °C. Experiments were carried out with different ceria shapes via two-step redox cycling composed of endothermic partial reduction of ceria with methane and complete exothermic re-oxidation of reduced ceria with H2 O/CO2 at the same operating temperature, thereby demonstrating the capability to operate the cycle isothermally. A parametric study considering different ceria macrostructure variants(ceria packed powder, ceria packed powder mixed with inert Al2 O3 particles, and ceria reticulated porous foam) and operating parameters(methane flow-rate, reduction temperature, or sintering temperature) was conducted in order to unravel their impact on the bed-averaged oxygen non-stoichiometry(δ), syngas yield, methane conversion, and solar reactor performance. The ceria cycling stability was also experimentally investigated to demonstrate repeatable syngas production by alternating the flow between CH4 and H2 O(or CO2). A decrease in sintering temperature of the ceria foam was beneficial for increasing syngas selectivity, methane conversion,and reactor performance. Increasing both CH4 concentration and reduction temperature enhanced δ with the maximum value up to 0.41 but concomitantly favored CH4 cracking reaction. The ceria reticulated porous foam showed better performance in terms of effective heat transfer, due to volumetric absorption of concentrated solar radiation and uniform heating with lower solar power consumption, thereby promoting the solar-to-fuel energy conversion efficiency that reached up to 5.60%. The energy upgrade factor achieved during cycle was up to 1.19. Stable patterns in the δ and syngas yield for consecutive cycles with the ceria foam validated material performance stability.

Chemical looping catalytic gasification of biomass over active LaNixFe1-xO_(3)perovskites as functional oxygen carriers

Oxygen carriers(OCs)with perovskite structure are attracting increasing interests due to their redox tunability by introducing various dopants in the structure.In this study,LaNixFe1-xO3(x=0,0.1,0.3,0.5,0.7,1.0)perovskite OCs have been prepared by a citric acid–nitrate sol–gel method,characterized by means of X-ray diffraction(XRD)analysis and tested for algae chemical looping gasification in a fixed bed reactor.The effects of perovskite types,OC/biomass mass ratio(O/B),gasification temperature and water injection rate on the gasification performance were investigated.Lower Ni-doped(0≤x≤0.5)perovskites crystalized in the rhombohedra system which was isostructural with LaNiO3,while those with composition 0.5≤x≤1 crystalized in the orthorhombic system.Despite the high reactivity for LaNiO_(3),LaNi_(0.5)Fe_(0.5)O_(3)(LN5F5)was found to be more stable at a high temperature and give almost as good results as LaNiO_(3)in the formation of syngas.The relatively higher syngas yield of 0.833 m^(3)·kg^(-1) biomass was obtained under the O/B of 0.4,water injection rate of 0.3 ml·min^(-1) and gasification temperature at 850C.Continuous high yield of syngas was achieved during the first 5 redox cycles,while a slight decrease in the reactivity for LN5F5 after 5 cycles was observed due to the adhesion of small grains occurring on the surface of OCs.However,an obvious improvement in the gasification performance was attained for LN5F5 compared to raw biomass direct gasification,indicating that LN5F5 is a promising functional OC for chemical looping catalytic gasification of biomass.

Evaluation of multi-cycle performance of chemical looping dry reforming using CO_2 as an oxidant with Fe–Ni bimetallic oxides

Chemical looping dry reforming（CLDR） is an innovative technology for CO2 utilization using the chemical looping principle.The CLDR process consists of three stages,i.e.CH4 reduction,CO2 reforming,and air oxidation.Spinel nickel ferrite（NiFe2O4） was prepared and its multi-cycle performance as an oxygen carrier for CLDR was experimentally investigated.X-ray diffraction（XRD） and Laser Raman spectroscopy showed that a pure spinel crystalline phase（NiFe2O4） was obtained by a parallel flow co-precipitating method.NiFe2O4was reduced into Fe-Ni alloy and wustite（FexO） during the CH4 reduction process.Subsequent oxidation of the reduced oxygen carrier was performed with CO2 as an oxidant to form an intermediate state：a mixture of spinel Ni（1-x）Fe（2＋x）O4,Fe（2＋y）O4 and metallic Ni.And CO was generated in parallel during this stage.Approximate 185 mL of CO was generated for 1 g spinel NiFe2O4 in a single cycle.The intermediate oxygen carrier was fully oxidized in the air oxidation stage to form a mixture of Ni（1＋x）Fe（2-x）O4 and Fe2O3.Although the original state of oxygen carrier（NiFe2O4） was not fully regenerated and agglomeration was observed,a good recyclability was shown in 10 successive redox cycles.

CO_2 capture by carbonated carbide slag seriflux after drying in calcium looping cycles

A new carbide slag （CS） seriflux utilization was proposed. The flue gas from a coal-fired plant was first bubbled into CS seriflux for CO2 capture. The obtained carbonated carbide slag seriflux （CCSS） was dried and utilized as a CO2 sorbent in the calcium looping cycles. The CO2 capture behavior of the dried CCSS and the raw CS was investigated in a dual fixed-bed reactor and a thermo- gravimetric analyzer. The effects of carbonation time, calcination temperature and carbonation temperature on CO2 capture performance of CCSS in the multiple carbonation/ calcination cycles were studied. The results show that the CO2 capture capacity of CCSS was higher than that of CS. Calcined at 950 ℃, CCSS shows better carbonation reactivity than CS, which benefits CO2 capture under severe calcination conditions. In the range of 700 to 725℃ for the carbonation, CCSS shows the optimal CO2 capture performance. The calcined CCSS shows better porous microstructure than the calcined CS. The calcined CCSS exhibits a larger surface area and pore volume in the cycles, which favors a higher CO2 capture capacity in the multiple cycles.

Petroleum coke conversion behavior in catalyst-assisted chemical looping combustion

Efficiently using petroleum coke as fuel and reducing carbon emission meanwhile have become attractive in oil processing industry.The paper is focused on the application of Chemical Looping Combustion(CLC)with petroleum coke,with the purpose of investigating its combustion performance and effects of potassium.Some experiments were performed in a laboratory scale fluidized bed facility with a natural manganese-based oxygen carrier.Experimental results indicated that the coke conversion is very sensitive to reaction temperature.The pre sent natural manganese-based oxygen carrier decorated by K has little effect on the improvement of coke conversion.XRD,SEM-EDX,and H2-TPR were adopted to characterize the reacted oxygen carrier samples.After being decorated by K,the oxygen carrier's capacity of transferring oxygen was decrea sed.A calcination temperature above the melting point of K2 CO3(891℃)shows better oxygen transfer reactivity in comparison to the one calcined at a lower temperature.The natural oxygen carrier used in the work has a high content of Si,which can easily react with K to form K(FeSi2 O6).Further,irrespective of reaction temperature,the coke conversion can be significantly enhanced by decorating the coke with K,with a demonstration of remarkably shorter reaction time,faster average coke gasification rate and higher average carbon conversion rate.

Efficient hydrogen production through the chemical looping redox cycle of YSZ supported iron oxides

The chemical looping process,where an oxygen carrier is reduced and oxidized in a cyclic manner,offers a promising option for hydrogen production through splitting water because of the much higher water splitting efficiency than solar electrocatalytic and photocatalytic process.A typical oxygen carrier has to comprise a significant amount of inert support,to maintain stability in multiple redox cycles,thereby resulting in a trade-off between the reaction reactivity and stability.Herein,we proposed the use of ion-conductive yttria-stabilized zirconia(YSZ)support Fe_(2)O_(3)to prepare oxygen carriers materials.The obtained Fe_(2)O_(3)/YSZ composites showed high reactivity and stability.Particularly,Fe_(2)O_(3)/YSZ-20(oxygen storage capacity,24.13%)exhibited high hydrogen yield of~10.30 mmol g^(-1) and hydrogen production rate of~0.66 mmol g^(-1) min^(-1) which was twice as high as that of Fe_(2)O_(3)/Al_(2)O_(3).Further,the transient pulse test indicated that active oxygen diffusion was the ratelimiting step during the redox process.The electrochemical impedance spectroscopy(EIS)measurement revealed that the YSZ support addition facilitated oxygen diffusion of materials,which contributed to the improved hydrogen production performance.The support effect obtained in this work provides a potentially efficient route for the modification of oxygen carrier materials.