期刊文献+
共找到2,037篇文章
< 1 2 102 >
每页显示 20 50 100
里氏木霉Rut—30产纤维素酶发酵条件的优化 被引量:14
1
作者 杜先林 李辉 +2 位作者 王义强 陈介南 张伟涛 《中南林业科技大学学报》 CAS CSCD 北大核心 2010年第9期112-119,共8页
采用单因素试验、正交试验设计对产纤维素酶的里氏木霉RutC—30菌株进行了液体摇瓶发酵条件优化实验。结果表明,在pH为4.8、每50 mL发酵液接种2.5 mL菌种时,里氏木霉RutC—30菌株产酶发酵最优培养条件是:工业纤维素30 g/L、(NH4)2SO412 ... 采用单因素试验、正交试验设计对产纤维素酶的里氏木霉RutC—30菌株进行了液体摇瓶发酵条件优化实验。结果表明,在pH为4.8、每50 mL发酵液接种2.5 mL菌种时,里氏木霉RutC—30菌株产酶发酵最优培养条件是:工业纤维素30 g/L、(NH4)2SO412 g/L、Mandels营养盐浓缩液125 mL/L。在此条件下,发酵产生的纤维素酶滤纸酶活达到4.845 U.m L-1,相对于微晶纤维素碳源提高了49.6%。同时,在本实验中还发现里氏木霉RutC—30菌株的生长与产酶存在着偶联性。通过优化实验,里氏木霉RutC—30菌株达到了比较高的产纤维素酶能力,为纤维素酶进一步工业化生产奠定了一定基础。 展开更多
关键词 纤维素酶 里氏木霉rut—30 发酵优化 滤纸酶活 正交实验设计
下载PDF
热处理工艺对RuT300蠕墨铸铁力学性能与导热性能的影响 被引量:11
2
作者 武岳 李建平 +3 位作者 张延京 杨忠 陶栋 杨通 《材料热处理学报》 EI CAS CSCD 北大核心 2017年第2期143-151,共9页
对Ru T300蠕墨铸铁合金进行了900℃、950℃、1000℃正火处理,并对1000℃加热处理的试样进行不同冷却处理(炉冷,空冷,风冷和喷水雾冷)。与铸态合金相比,热处理后的Ru T300蠕墨铸铁合金中珠光体含量随奥氏体化加热温度提高而增高。并且随... 对Ru T300蠕墨铸铁合金进行了900℃、950℃、1000℃正火处理,并对1000℃加热处理的试样进行不同冷却处理(炉冷,空冷,风冷和喷水雾冷)。与铸态合金相比,热处理后的Ru T300蠕墨铸铁合金中珠光体含量随奥氏体化加热温度提高而增高。并且随着奥氏体化后冷却速度的增大,珠光体含量逐渐增高,最高可达77.6%,较铸态组织增加了50%,珠光体层片间距逐渐减小,最小间距约为0.2μm,较铸态珠光体减小了0.4μm,抗拉强度和布氏硬度分别提高了25%和73%,但导热性能下降20%~30%。热处理后蠕虫状石墨数量和尺寸有所减小(1000℃),石墨与基体结合部位会出现开裂、脱粘现象,导致传热受阻,导热率下降。 展开更多
关键词 rut300蠕墨铸铁 正火 力学性能 导热性能
下载PDF
Rutting resistance of asphalt mixtures in the middle course 被引量:4
3
作者 杨军 于良溟 +2 位作者 万军 陈军 钱国超 《Journal of Southeast University(English Edition)》 EI CAS 2006年第2期270-272,共3页
In order to improve the rutting resistance of asphalt mixtures in the middle course to reduce the rutting of asphalt pavement, the influence of different types of gradation with their own optimal asphaltaggregate rati... In order to improve the rutting resistance of asphalt mixtures in the middle course to reduce the rutting of asphalt pavement, the influence of different types of gradation with their own optimal asphaltaggregate ratios is analyzed. Some investigations are made out on the mixture in the middle course through the modified wheel tracking test in air bath and the Hamburg wheel tracking test (HWTT) in water bath, and the results of which are compared with the corresponding research in Germany. Results show that the Sup20 and the modified AC-20I have better performance than that of AC-20I under the same test conditions. In addition, the high-quality bitumen and hard aggregate can improve the rutting performance of the mixture in water-submerged conditions. The selection of modified asphalt, hard aggregate and a reasonable gradation are essential to the improvement of the rutting resistance of the mixtures used in the middle course. 展开更多
关键词 middle course rutTING modified asphalt modified wheel tracking test Hamburg wheel tracking test
下载PDF
Asphalt pavement short-term rutting analysis and prediction considering temperature and traffic loading conditions 被引量:5
4
作者 黄晓明 杨毅文 +1 位作者 李辉 刘媚 《Journal of Southeast University(English Edition)》 EI CAS 2009年第3期385-390,共6页
The rutting simulation method considering temperature variance and traffic time distribution is developed through ABAQUS software. The short-term behavior of pavement rut under the effects of temperature and traffic l... The rutting simulation method considering temperature variance and traffic time distribution is developed through ABAQUS software. The short-term behavior of pavement rut under the effects of temperature and traffic loading is addressed. Then sensitivity analysis on the factors of temperature and traffic loading is conducted and a short-term rutting prediction model is developed. The results show that under the same conditions of temperature and the number of load repetitions, rut increases sharply with the contact pressure in a linear manner, while as for the heavy load situation, the increases likely to be more nonlinear and faster; the significant factors affecting rutting include daily maximum air temperature, daily solar radiation volume, daily minimum air temperature, tire-pavement contact pressure and the number of load repetitions. Finally, a short-term rutting prediction model reflecting the effects of air temperature and traffic loading is developed, and it can be used for prediction and pre-waming for pavement rut prevention. 展开更多
关键词 short-term rutting asphalt pavement ABAQUS
下载PDF
响应面法优化里氏木霉Rut C-30产纤维素酶液体培养基 被引量:20
5
作者 李勇昊 姜永生 +3 位作者 周长海 顾芮萌 孙文良 田朝光 《中国酿造》 CAS 2012年第4期29-32,共4页
该试验在单因素对里氏木霉(Trichoderma reesei)Rut C-30产纤维素酶的液体培养基优化的基础上,以滤纸酶活为响应值,采用响应面法确定其最佳培养基。首先通过Plackett-Burman(PB)设计筛选出影响滤纸酶活的显著因素,结晶纤维素和麸皮;通... 该试验在单因素对里氏木霉(Trichoderma reesei)Rut C-30产纤维素酶的液体培养基优化的基础上,以滤纸酶活为响应值,采用响应面法确定其最佳培养基。首先通过Plackett-Burman(PB)设计筛选出影响滤纸酶活的显著因素,结晶纤维素和麸皮;通过最陡爬坡试验逼近最大酶活力区域;最后通过Central Composite Design(CCD)设计及响应面分析确定产酶最佳培养基,其中影响酶活的显著性因素结晶纤维素41.8g,麸皮19.1g。经过优化,滤纸酶活力最高为8.21U/mL,比单因素优化结果7.03U/mL提高了16.78%,同时测得CMC酶活为63.64IU/mL,木聚糖酶活为27.4IU/mL,葡萄糖苷酶酶活0.96IU/mL。 展开更多
关键词 纤维素酶 里氏木霉rutC-30 液体发酵 响应面法 滤纸酶活
下载PDF
Prediction method of highway pavement rutting based on the grey theory 被引量:6
6
作者 周岚 倪富健 赵岩荆 《Journal of Southeast University(English Edition)》 EI CAS 2015年第3期396-400,共5页
In order to make a scientific pavement maintenance decision, a grey-theory-based prediction methodological framework is proposed to predict pavement performance. Based on the field pavement rutting data,analysis of va... In order to make a scientific pavement maintenance decision, a grey-theory-based prediction methodological framework is proposed to predict pavement performance. Based on the field pavement rutting data,analysis of variance (ANOVA)was first used to study the influence of different factors on pavement rutting. Cluster analysis was then employed to investigate the rutting development trend.Based on the clustering results,the grey theory was applied to build pavement rutting models for each cluster, which can effectively reduce the complexity of the predictive model.The results show that axial load and asphalt binder type play important roles in rutting development.The prediction model is capable of capturing the uncertainty in the pavement performance prediction process and can meet the requirements of highway pavement maintenance,and,therefore,has a wide application prospects. 展开更多
关键词 prediction method grey theory cluster analysis analysis of variance pavement rutting
下载PDF
Virtual rutting test of asphalt mixture using discrete element method 被引量:6
7
作者 张德育 黄晓明 高英 《Journal of Southeast University(English Edition)》 EI CAS 2012年第2期215-220,共6页
In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method (DEM). A digital specimen g... In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method (DEM). A digital specimen generation procedure considering aggregate gradation and irregular shape is developed based on the probability theory and the Monte Carlo method. The virtual rutting test is then conducted based on the generated digital specimen. In addition, on the basis of the time-temperature superposition (TTS) principle, a calculation method is used to reduce the computation time of the virtual rutting test. The simulation results are compared with the laboratory measurements. The results show that the calculation method based on the TFS principle in the discrete element (DE) viscoelastic model can significantly reduce the computation time. The deformation law of asphalt mixtures in the virtual rutting test is similar to the laboratory measurements, and the deformation and the dynamic stability of the virtual rutting test are slightly greater than the laboratory measurements. The two-dimensional virtual rutting test can predict the permanent deformation performance of asphalt mixtures. 展开更多
关键词 asphalt mixture permanent deformation discrete element method virtual rutting test
下载PDF
对里氏木霉Rut C-30所产非淀粉多糖酶系的分析 被引量:4
8
作者 程池 乐易林 +2 位作者 熊涛 姚粟 曾哲灵 《食品与发酵工业》 CAS CSCD 北大核心 2004年第6期64-67,共4页
通过里氏木霉RutC 3 0以稻草和麸皮为基质进行固态发酵 ,对其产生的非淀粉多糖酶(NSP酶 )进行分析 ,试验表明里氏木霉RutC 3 0产生的NSP酶系较全 ,分别有纤维素酶、木聚糖酶、β 葡聚糖酶、β 甘露聚糖酶、果胶酶等 5种不同的NSP酶。并... 通过里氏木霉RutC 3 0以稻草和麸皮为基质进行固态发酵 ,对其产生的非淀粉多糖酶(NSP酶 )进行分析 ,试验表明里氏木霉RutC 3 0产生的NSP酶系较全 ,分别有纤维素酶、木聚糖酶、β 葡聚糖酶、β 甘露聚糖酶、果胶酶等 5种不同的NSP酶。并探讨了不同碳源及添加不同底物诱导物对里氏木霉RutC 3 展开更多
关键词 里氏木霉rutC-30 非淀粉多糖酶系 稻草 固态发酵 碳源 底物诱导物 产酶种类
下载PDF
RuT300蠕墨铸铁熔炼工艺研究 被引量:7
9
作者 张馨心 张国伟 徐宏 《铸造技术》 CAS 北大核心 2012年第10期1200-1202,共3页
探讨了RuT300蠕墨铸铁在12 kg中频感应电炉中的熔炼工艺。采用FeSiMg5RE5蠕化剂,硅钡合金孕育剂,以及凹坑法蠕化处理工艺,研究了蠕化剂加入量、出铁温度及蠕化时间对蠕化率的影响。实验得出最佳的熔炼工艺为:蠕化剂加入量为0.65%,出铁... 探讨了RuT300蠕墨铸铁在12 kg中频感应电炉中的熔炼工艺。采用FeSiMg5RE5蠕化剂,硅钡合金孕育剂,以及凹坑法蠕化处理工艺,研究了蠕化剂加入量、出铁温度及蠕化时间对蠕化率的影响。实验得出最佳的熔炼工艺为:蠕化剂加入量为0.65%,出铁温度为1 560℃,蠕化时间为25 s。 展开更多
关键词 rut300 熔炼 蠕化率
下载PDF
里氏木霉Rut C-30产非淀粉多糖酶发酵条件的研究 被引量:2
10
作者 单达聪 王雅民 张董燕 《食品与发酵工业》 CAS CSCD 北大核心 2009年第4期111-115,共5页
在接种量与培养温度分别为8%和30℃条件下,采用正交试验表L9(34)设计对培养基组成、发酵时间、培养基湿度和发酵容器4个试验因子进行产酶影响力排序和条件组合优化,同时分析各指标间相关性。结果:对纤维素酶,培养基组成>发酵时间>... 在接种量与培养温度分别为8%和30℃条件下,采用正交试验表L9(34)设计对培养基组成、发酵时间、培养基湿度和发酵容器4个试验因子进行产酶影响力排序和条件组合优化,同时分析各指标间相关性。结果:对纤维素酶,培养基组成>发酵时间>发酵容器>初始湿度,最优组合酶活力456.3u/g;对木聚糖酶,发酵时间>培养基组成>发酵容器>初始湿度,最优组合酶活力5529.9u/g;对β-甘露聚糖酶,发酵容器>培养基组成>初始湿度>发酵时间,优化组合酶活力367.6u/g;对果胶酶,培养基组成>发酵容器>发酵时间>初始湿度,最优组合酶活力为544.6u/g;培养基发酵失重与β-甘露聚糖酶活力极显著正相关(r=0.811,P<0.01)、纤维素酶与木聚糖酶活力显著正相关(r=0.724,P<0.05)。结论:通过改变发酵条件可调控该菌株产饲用NSP酶谱的酶活水平与比例,指标之间相关性可用于监测发酵过程中的酶活力状态。该菌株较适合作为饲用NSP复合酶制剂生产的菌株。 展开更多
关键词 里氏木酶rut C-30 固态发酵 非淀粉多糖酶 发酵条件 影响力 相关性
下载PDF
Calculation of effective temperature for pavement rutting using numerical simulation methods 被引量:2
11
作者 祝谭雍 马涛 黄晓明 《Journal of Southeast University(English Edition)》 EI CAS 2016年第3期362-367,共6页
In order to predict the long-term rutting of asphalt pavement, the effective temperature for pavement rutting is calculated using the numerical simulation method. The transient temperature field of asphalt pavement wa... In order to predict the long-term rutting of asphalt pavement, the effective temperature for pavement rutting is calculated using the numerical simulation method. The transient temperature field of asphalt pavement was simulated based on actual meteorological data of Nanjing. 24-hour rutting development under a transient temperature field was calculated in each month. The rutting depth accumulated under the static temperature field was also estimated and the relationship between constant temperature parameters was analyzed. Then the effective temperature for pavement rutting was determined based on the rutting equivalence principle. The results show that the monthly effective temperature is above 40 t in July and August, while in June and September it ranges from 30 to 40 Rutting development can be ignored when the monthly effective temperature is less than 30 t. The yearly effective temperature for rutting in Nanjing is around 38. 5 t. The long-term rutting prediction model based on the effective temperature can reflect the influences of meteorological factors and traffic time distribution. 展开更多
关键词 transient temperature field long-term rutting effective temperature numerical simulation finite element method
下载PDF
^(113)C-UBT和RUT检测幽门螺杆菌分析 被引量:1
12
作者 徐丽姝 麦韵屏 张瑛华 《实用医学杂志》 CAS 2004年第8期916-917,共2页
目的 :评价目前临床上常用的两种诊断幽门螺杆菌 (HP)感染方法的敏感性、特异性。方法 :对 186例因消化道症状就医的老年患者行胃镜检查 ,同时行13 C 尿素呼气试验 ( 13 C UBT) ,快速尿素酶 (RUT)试验检查 ,用活检钳钳取胃窦黏膜组织行... 目的 :评价目前临床上常用的两种诊断幽门螺杆菌 (HP)感染方法的敏感性、特异性。方法 :对 186例因消化道症状就医的老年患者行胃镜检查 ,同时行13 C 尿素呼气试验 ( 13 C UBT) ,快速尿素酶 (RUT)试验检查 ,用活检钳钳取胃窦黏膜组织行病理学检查。结果 :13 C UBT较RUT检查的敏感性、特异性高。结论 :13 C UBT和RUT具有安全、简便、可靠、无创的特点 ,是较好的HP检测方法 ,对于老年病人13 C 展开更多
关键词 ^113C-UBT rut 幽门螺杆菌 HP 致病菌
下载PDF
微织构铣刀干铣削RuT500切削性能研究 被引量:1
13
作者 李俚 方枭 +3 位作者 赖徳斌 林勇传 冀全鑫 李胜柱 《组合机床与自动化加工技术》 北大核心 2023年第2期41-44,共4页
为探究微织构对刀具加工蠕墨铸铁RuT500切削性能的影响,改善RuT500的可加工性,利用激光技术在刀具前刀面制备了3种形式的微织构并通过单因素试验方法,在不同切削速度下将微织构刀具和无织构刀具对RuT500进行铣削加工,对比分析了微织构... 为探究微织构对刀具加工蠕墨铸铁RuT500切削性能的影响,改善RuT500的可加工性,利用激光技术在刀具前刀面制备了3种形式的微织构并通过单因素试验方法,在不同切削速度下将微织构刀具和无织构刀具对RuT500进行铣削加工,对比分析了微织构的方向和类型在加工中切削性能的差异。结果表明,表面微织构可以有效降低切削力,改善切屑形态和工件表面质量,在一定程度上降低了前刀面磨损;3种微织构在部分相同切削速度下对切削性能的影响有较大差别;切削速度较大时,微织构更有利于RuT500的切削加工。在3种微织构中,以平行于主切削刃的沟槽织构刀具切削性能最优。 展开更多
关键词 rut500 微织构 铣削力 刀具磨损 表面粗糙度 切屑形貌
下载PDF
特级生铁对RuT300蠕化工艺的影响 被引量:1
14
作者 李晶晶 张国伟 《铸造技术》 CAS 北大核心 2015年第2期416-419,共4页
探讨了特级生铁作为原料在12 kg中频感应电炉中生产蠕墨铸铁的熔炼工艺。采用FeSiMg5RE5蠕化剂,硅钡合金孕育剂,以及凹坑法蠕化处理工艺,研究了蠕化剂加入量对蠕化率的影响。实验得出最佳实验工艺:出铁温度(1 560±10)℃,蠕化剂加入... 探讨了特级生铁作为原料在12 kg中频感应电炉中生产蠕墨铸铁的熔炼工艺。采用FeSiMg5RE5蠕化剂,硅钡合金孕育剂,以及凹坑法蠕化处理工艺,研究了蠕化剂加入量对蠕化率的影响。实验得出最佳实验工艺:出铁温度(1 560±10)℃,蠕化剂加入量0.45%,蠕化孕育时间(30±2)s,蠕化率高达95%,抗拉强度≥330 MPa,伸长率≥3.0%。 展开更多
关键词 rut300 熔炼 蠕化率
下载PDF
DIGFA与RUT对幽门螺杆菌感染的诊断价值
15
作者 张萍 吴玉平 《浙江预防医学》 2000年第6期63-64,共2页
关键词 DIGFA rut 诊断 幽门螺杆菌感染
下载PDF
Al_(2)O_(3)-TiC复合陶瓷刀具干切削RuT450表面质量研究
16
作者 林勇传 冀全鑫 +2 位作者 赖德斌 周宇峰 韦珏宇 《组合机床与自动化加工技术》 北大核心 2021年第10期151-154,共4页
为探究和改善蠕墨铸铁RuT450切削加工性能,基于正交试验,采用涂层/无涂层Al_(2)O_(3)-TiC复合陶瓷刀具对RuT450进行车削加工,探究涂层和切削参数对工件表面质量的影响及机理,为复合陶瓷刀具切削RuT450提供理论依据。结果表明:涂层复合... 为探究和改善蠕墨铸铁RuT450切削加工性能,基于正交试验,采用涂层/无涂层Al_(2)O_(3)-TiC复合陶瓷刀具对RuT450进行车削加工,探究涂层和切削参数对工件表面质量的影响及机理,为复合陶瓷刀具切削RuT450提供理论依据。结果表明:涂层复合陶瓷刀具切削一致性更好,更适合加工RuT450;对RuT450表面粗糙度影响最显著的因素是进给速度,其次是切削速度,背吃刀量对表面粗糙度的影响程度相对较小;切削速度(Vc=400 m/min)、进给速度(f=0.05 mm/r)、背吃刀量(a p=1 mm)时能获得最好的表面粗糙度;表面硬度随着切削速度的增大而增大,而随着进给速度、背吃刀量的增大基本不会出现明显的变化。 展开更多
关键词 rut450 陶瓷刀具 切削参数 表面质量
下载PDF
RuT450气缸盖铸造工艺的研究
17
作者 谢永泽 吕登红 《铸造工程》 2023年第S02期36-40,共5页
根据RuT450柴油机气缸盖的技术要求确定了铸造工艺,通过MAGMA软件对充型、凝固及缺陷等进行分析,验证铸造工艺的可行性。采用铸件浇注后在砂型内延缓开箱时间,在箱内缓慢冷却的免退火处理工艺,铸件的残余应力小于40 MPa,同时铸件的力学... 根据RuT450柴油机气缸盖的技术要求确定了铸造工艺,通过MAGMA软件对充型、凝固及缺陷等进行分析,验证铸造工艺的可行性。采用铸件浇注后在砂型内延缓开箱时间,在箱内缓慢冷却的免退火处理工艺,铸件的残余应力小于40 MPa,同时铸件的力学性能和组织均满足技术要求。 展开更多
关键词 气缸盖 rut450 铸造工艺
下载PDF
里氏木霉Rut-C30发酵热水预处理稻草产纤维素酶 被引量:4
18
作者 苏存生 贺建龙 +3 位作者 熊鹏 岳春 于凤川 孙付保 《食品与发酵工业》 CAS CSCD 北大核心 2016年第10期14-22,共9页
为提高工业生产菌Trichoderma reesei Rut-C30产酶能力,以热水预处理稻草(hot water pretreated rice straw,HWPRS)为碳源,开展系统优化培养基与培养条件以及采用添加剂等方面的实验工作。菌株初始摇瓶发酵HWPR产纤维素酶在168 h时滤纸... 为提高工业生产菌Trichoderma reesei Rut-C30产酶能力,以热水预处理稻草(hot water pretreated rice straw,HWPRS)为碳源,开展系统优化培养基与培养条件以及采用添加剂等方面的实验工作。菌株初始摇瓶发酵HWPR产纤维素酶在168 h时滤纸酶活(FPA)为1.20 U/m L。通过单因素实验与正交实验,获得最佳培养基(g/L):HWPRS 50.0、玉米浆6.0、(NH_4)_2SO_44.0、KH_2PO_41.0、尿素0.2、MgSO_4·7H_2O 0.4、CaCl_20.3;最佳培养条件:pH6.0、转速220 r/min、温度30℃、接种量φ6%;优化后菌株产酶FPA达2.69 U/m L,是优化前2倍以上。添加吐温-80能显著提高产酶,β-葡萄糖苷酶活(BG)提高26%;添加乳糖主要能提高BG酶活;实验中首次发现壳聚糖类物质能促进纤维素酶发酵,其中壳聚糖效果最明显,添加1.5 g/L壳聚糖时纤维素酶FPA与BG分别提高了10%和30%,使纤维素酶FPA、CMCase和BG分别达到3.67、8.65和1.76 U/m L。该产酶稳定性为上罐实验证实,所产纤维素酶FPA水平是初始摇瓶发酵的3倍,初步显示了其工业发酵潜力。 展开更多
关键词 热水预处理稻草 里氏木霉rut-C30 纤维素酶 发酵优化 壳聚糖
下载PDF
紫外诱变里氏木霉Rut C-30提高木聚糖酶活力及发酵条件的研究 被引量:2
19
作者 乐易林 熊涛 +1 位作者 曾哲灵 程池 《食品与发酵工业》 CAS CSCD 北大核心 2005年第1期74-76,共3页
通过紫外照射的方法 ,对里氏木霉RutC 30进行诱变 ,选育出高产木聚糖酶活力的菌株 ,其酶活比出发菌株提高了 4 1 9%。并对选育的菌株进行了稻草与麸皮比例 ,氮源以及干料与水分比对产酶的影响 ,并通过正交实验 ,阐明培养温度、时间、MgS... 通过紫外照射的方法 ,对里氏木霉RutC 30进行诱变 ,选育出高产木聚糖酶活力的菌株 ,其酶活比出发菌株提高了 4 1 9%。并对选育的菌株进行了稻草与麸皮比例 ,氮源以及干料与水分比对产酶的影响 ,并通过正交实验 ,阐明培养温度、时间、MgSO4·7H2 O和KH2 PO4对产酶的影响。 展开更多
关键词 选育 木聚糖酶 菌株 高产 里氏木霉 发菌 麸皮 发酵条件 紫外诱变 KH2PO4
下载PDF
^(14)C-UBT和RUT诊断慢性胃炎Hp感染110例分析
20
作者 张弥海 郑春大 +2 位作者 吴东初 单汉清 吴秀美 《胃肠病学和肝病学杂志》 CAS 2001年第4期384-384,共1页
关键词 碳14-UBT rut 诊断 胃炎 HP感染
下载PDF
上一页 1 2 102 下一页 到第
使用帮助 返回顶部