A Review:Pre-lithiation Strategies Based on Cathode Sacrificial Lithium Salts for Lithium-Ion Capacitors

Similar to lithium-ion batteries(LIBs),during the first charge/discharge process of lithium-ion capacitors(LICs),lithium-intercalated anodes(e.g.,silicon,graphite,and hard carbon)also exhibit irreversible lithium intercalation behaviors,such as the formation of a solid electrolyte interface(SEI),which will consume Li^(+)in the electrolyte and significantly reduce the electrochemical performance of the system.Therefore,pre-lithiation is an indispensable procedure for LICs.At present,commercial LICs mostly use lithium metal as the lithium source to compensate for the irreversible capacity loss,which has the demerits of operational complexity and danger.However,the pre-lithiation strategy based on cathode sacrificial lithium salts(CSLSs)has been proposed,which has the advantages of low cost,simple operation,environmental protection,and safety.Therefore,there is an urgent need for a timely and comprehensive summary of the application of CSLSs to LICs.In this review,the important roles of pre-lithiation in LICs are detailed,and different pre-lithiation methods are reviewed and compared systematically and comprehensively.After that,we systematically discuss the pre-lithiation strategies based on CSLSs and mainly introduce the lithium extraction mechanism of CSLSs and the influence of intrinsic characteristics and doping amount of CSLSs on LICs performance.In addition,a summary and outlook are conducted,aiming to provide the essential basic knowledge and guidance for developing a new pre-lithiation technology.

Influence of Mg and Ti on the microstructure and electrochemical performance of aluminum alloy sacrificial anodes

The experiments focused on the influence of magnesium and titanium as additional alloying elements on the microstructure and electro-chemical behavior of Al-Zn-In sacrificial anodes. The electrochemical behavior of the aluminum sacrificial anode with 3 wt.% sodium chloride solution was studied by electrochemical impedance spectroscopy (EIS) tests. It was found that a microstructure with few precipitates and refined grains could be achieved by adding 1 wt.% Mg and 0.05 wt.% Ti to the Al-Zn-In alloy,resulting in the improved current capacity and efficiency of the alloy. The equivalent circuit based on the EIS experimental data revealed less corrosion and lower adsorbed corrosion production on the surface of the aluminum alloy with a combination of 1 wt.% Mg and 0.05 wt.% Ti,which suggested that the corrosion behavior seemed to be strongly related to the presence of precipitate particles in the aluminum alloy,and moderate amounts of precipitate particles could be beneficial to the electrochemical performance of the aluminum alloy sacrificial anode.

Sacrificial microgel‑laden bioink‑enabled 3D bioprinting of mesoscale pore networks

Three-dimensional(3D)bioprinting is a powerful approach that enables the fabrication of 3D tissue constructs that retain complex biological functions.However,the dense hydrogel networks that form after the gelation of bioinks often restrict the migration and proliferation of encapsulated cells.Herein,a sacrificial microgel-laden bioink strategy was designed for directly bioprinting constructs with mesoscale pore networks(MPNs)for enhancing nutrient delivery and cell growth.The sacrificial microgel-laden bioink,which contains cell/gelatin methacryloyl(GelMA)mixture and gelled gelatin microgel,is first thermo-crosslinked to fabricate temporary predesigned cell-laden constructs by extrusion bioprinting onto a cold platform.Then,the construct is permanently stabilized through photo-crosslinking of GelMA.The MPNs inside the printed constructs are formed after subsequent dissolution of the gelatin microgel.These MPNs allowed for effective oxygen/nutrient diffusion,facilitating the generation of bioactive tissues.Specifically,osteoblast and human umbilical vein endothelial cells encapsulated in the bioprinted large-scale constructs(≥1 cm)with MPNs showed enhanced bioactivity during culture.The 3D bioprinting strategy based on the sacrificial microgel-laden bioink provided a facile method to facilitate formation of complex tissue constructs with MPNs and set a foundation for future optimization of MPN-based tissue constructs with applications in diverse areas of tissue engineering.

Seismic response of rocking isolated railway bridge piers with sacrificial components

In this study, sacrificial components were incorporated into self-centering railway bridge piers to improve the lateral stiffness. The seismic response of this new detail was investigated. First, the method to compute the initial uplift moment of the self-centering pier is given. In addition, shaking table tests were conducted on a free-rocking pier without sacrificial components, which was used to validate a two-spring numerical model. Good agreement was obtained between the numerical results and experimental data. Furthermore, the validated model was employed to investigate the influence of sacrificial components on the seismic response of rocking piers. For this purpose, two models were developed, with and without sacrificial components. Nonlinear response history analysis was then performed on both models under three historical motions. The results showed that compared to the one without sacrificial components, the rocking pier with sacrificial components has comparable displacement at the top of the pier, and maximum uplift moment at high amplitude motion. Therefore, incorporating sacrificial components into the rocking pier can increase the lateral stiffness at service load and low amplitude frequent earthquakes but can produce comparable response at high seismic excitation. These results provide support for performance-based seismic design of self-centering rocking piers.

Effect of Oxide Inclusions on Electrochemical Properties of Aluminium Sacrificial Anodes

Oxide films are incorporated into melts by an entrainment process, and are expected to be present in most metals, but particularly cast Al alloys. The oxides are necessarily present as folded-over double films （bifilms） that are effectively cracks. Their effect on the electrochemical behaviour of cast Al-SZn-0.021n sacrificial anodes was studied in 3 wt pct sodium chloride solution using the NACE efficiency evaluation. Three methods were employed to entrain progressive amounts of oxide in the alloy, including the addition of Al-Zn-ln maching chips to the charge, increasing the pouring height, and agitating the melt. The introduction of oxide bifilms in the cast alloy resulted in the deterioration of the electrochemical properties of the sacrificial anodes, such as current capacity and anode efficiency, and introduced increasing variability in these properties. The results suggest that corrosion behaviour is strongly related to the presence of bifilms suspended in the liquid alloy because bifilms provide crack paths allowing the corrodant to penetrate deeply into the metal matrix, and simultaneously provide localized galvanic cells because of the precipitation of Fe rich intermetallic compounds on their outer surfaces.

Effect of Sacrificial Anode Protection for Steel Pipe Piles at Dandong Port

The sacrificial anode protection system for the steel pipe piles of the 3rd berth of Dandong; wharf at Dandong port has operated for eight years. In this paper, the program design and the protection effect of the sacrificial anode protection system are presented. The results of various inspections show that the piles are protected very satisfactorily.

Effects of strain-induced melt activation treatment on the microstructure and properties of Zn sacrificial anodes

The microstructural properties and electrochemical performance of zinc(Zn)sacrificial anodes during strain-induced melt activation(SIMA)were investigated in this study.The samples were subjected to a compressive ratio of 20%-50% at various temperatures(425-435℃)and durations(5-30 min).Short-term electrochemical tests(anode tests)based on DNV-RP-B401 and potentiodynamic polarization tests were performed in 3.5wt%NaCl solution to evaluate the electrochemical efficiency and corrosion behavior of the samples,respectively.The electrochemical test results for the optimum sample confirmed that the corrosion current density declined by 90% and the anode efficiency slightly decreased relative to that of the raw sample.Energy-dispersive X-ray spectroscopy,scanning electron microscopy,metallographic images,and microhardness profiles showed the accumulation of alloying elements on the boundary and the conversion of uniform corrosion into localized corrosion,hence the decrease of the Zn sacrificial anode’s efficiency after the SIMA process.

Effects of Zinc Addition on the Performance of Aluminium as Sacrificial Anode in Seawater

In this work, the effect of zinc addition on the performance of aluminium-based sacrificial anode in seawater was investigated. The parameters used in assessing the performance of the cast anodes are anodic efficiency, protection efficiency and polarized potential. The percentages of Zn in the anodes were varied from 1 to 8%Zn. The alloys produced were tested as sacrificial anode for the protection of mild steel in seawater at room temperature. Current efficiency as high as 86.69% was achieved at 6%Zn in the alloys. The polarized potential obtained for the couples(steel/Al based alloys) are as given in the pourbaix diagrams with the steel lying within the immunity region/cathodic region ( S-0.5V SHE) and the sacrificial anodes within the anodic region. The protection offered by the sacrificial anodes to the steel after the 7th and 8th week were measured. Protection efficiency values as high as 99.26% and 99.13% were achieved after the 7th and 8th with Al-6%Zn. The microstructure showed the intermetallic structures of β-phase which breakdown the alumina passive film and thus enhancing the anode efficiency.

A novel method for sacrificial layer release in MEMS devices fabrication

During the forming process of the free-standing structure or the functional cavity when releasing the high aspect ratio sacrificial layer, such structures tend to stick to the substrate due to capillary force. This paper describes the application of pull-in length conception as design rules to a novel ＇dimpled＇ method in releasing sacrificial layer. Based on the conception of pull-in length in adhering Phenomenon, the fabrication and releasing sacrificial layer methods using micro bumps based on the silicon substrate were presented. According to the thermal isolation performances of one kind of micro electromechanical system device thermal shear stress sensor, the sacrificial layers were validated to be successfully released.

Direct Process to Prepare Crystallized Freestanding Membranes of Hydroxyapatite Using Sacrificial Layer of Barium-Compounds

Freestanding membrane (FSM) of hydroxyapatite (HA) is a thin sheet of pure HA without any supporting substrates. Our original preparation process of FSM of HA had three steps: The first was the deposition of HA layer on sacrificial layer of solvent-soluble materials, the second was separation of FSM of HA by means of dissolution of sacrificial layer, and the third was post-annealing to crystallize FSM of HA. To date, the post-annealing process was a serious bottleneck of productivity owing to its too long time. In this short report, we proposed a novel sacrificial layer, heatproof and water-soluble Ba-compound, which makes the direct deposition of crystallized HA possible due to its heatproof property because the problem on the original process was that the previous sacrificial layers have no heatproof property and HA layer should be deposited as amorphous. We can deposit the Ba-compound sacrificial layer only in 1 hour followed with the direct deposition of crystallized HA layer, substituting the 20 hours of post-annealing. The FSM of HA was separated successfully from the substrate by means of dissolution of Ba-compound with water. Our novel process can shrink the process time by 19 hours.

Environmental Impact Assessment of Sacrificial Anode Method in Taiwan Strait

Taiwan Strait is one of the potential wind farm in the world. Cooperate with the development of national policies, thousands of offshore wind turbines will be installed in Taiwan Strait. In order to enable offshore wind turbine foundation to be erected in the ocean for a long time, the offshore structure facilities are protected by sacrificial anode or impressed current of today. This study utilized the MIKE21 numerical model, combined with ocean parameters such as sea waves and tidal current to simulate the change of the diffusion concentration and diffusion range of the materials released by the aluminum sacrificial anode blocks by the Changhua offshore wind farm located on Taiwan Strait in winter and summer, thus to evaluate the impact on the marine environment.

Simulation of the Cracking and Ablation Behavior of Ferrosiliceous and Siliceous Nuclear Sacrificial Concretes

We investigated the simulation of the cracking and ablation behavior of ferro-siliceous and siliceous nuclear sacrificial concretes. To this end, four type of sacrificial concretes were fabricated, i e, the ferro-siliceous（F） and siliceous（S） plain concretes, and the polypropylene fiber reinforced concretes of the above two（FF, SF）. The cracking and ablation behaviors of the sacrificial concretes were investigated by simulation tests, and the simulated elevated temperature was obtained by means of thermite powder. The number and the width of the cracks were compared and the pore size distribution of sacrificial concretes was measured. In addition, the interface and chemical composition of melt at different positions were analyzed, and the ablation depth of the sacrificial concrete crucibles was also measured. It was found that the siliceous concrete shows to be more prone to cracking than the ferro-siliceous concrete due to the higher content of fly ash and lower water to binder ratio; though the ablation depth of siliceous concrete is found to be slightly larger, no clear difference can be detected for the basemat ablation rate.

Ritual Implements and Sacrificial Objects——Exhibits of Tibet Museum

Most TibetanBuddhist ritualimplements andsacrificialobjects were cast in gold,silver or copper, in additionto those made of wood,bone,stone,shells,cloth,silks and brocade heyconstitute an important partof he treasure house ofTibetan Buddhism.

Sacrificial Fires and Horsemanship in Yushu

ＳａｃｒｉｆｉｃｉａｌＦｉｒｅｓａｎｄＨｏｒｓｅｍａｎｓｈｉｐｉｎＹｕｓｈｕ￥／／ＧＹＡＹＵＮＧＱＵＮＰＥＳｉｎｃｅａｎｃｉｅｎｔｔｉｍｅｓ，Ｊｕｌｙｈａｓｂｅｅｎａｈｉｇｈｌｙｓｉｇｎｉｆｉｃａｎｔｒｅｌｉｇｉｏｕｓｍｏｎｔｈｄｕｒｉｎｇｗｈｉｃｈ...

A generalized synthesis method for freestanding multiferroic twodimensional layered supercell oxide films via a sacrificial buffer layer

Multiferroics are an intriguing family of materials due to the simultaneous presence of two ferroic orderings,namely,ferroelectricity and ferromagnetism.They are scientifically and technologically important and have numerous potential applications,such as four-state logic memories and multiferroic tunneling junctions.However,the growth of epitaxial singlephase multiferroic thin films typically requires single crystalline oxide substrates,which hinders their future integration with Sibased devices.In this study,we report a generalized synthesis method that uses the polydimethylsiloxane(PDMS)-assisted wetetching method with an Sr_(3)Al_(2)O_(6)(SAO)sacrificial layer to transfer freestanding single-phase multiferroic Bi_(2)NiMnO_(6)(BNMO)films from conventional SrTiO_(3)(STO)substrates onto a Si wafer.The structures and properties of the films have been characterized before and after the transfer.These transferred films possess good multiferroic properties on Si wafers,indicating full compatibility with modern Si technology.This method can be generally applicable to other Bi-based multiferroic materials as well.Lastly,the original STO substrates after the transfer process have been recycled for preparing new batches of freestanding BNMO films,indicating a low-cost and sustainable method for manufacturing large-volume freestanding complex oxide thin films.

Combining two-photon lithography with laser ablation of sacrificial layers:A route to isolated 3D magnetic nanostructures

Three-dimensional(3D)nanostructured functional materials are important systems allowing new means for intricate control of electromagnetic properties.A key problem is realising a 3D printing methodology on the nanoscale that can yield a range of functional materials.In this article,it is shown that two-photon lithography,when combined with laser ablation of sacrificial layers,can be used to realise such a vision and produce 3D functional nanomaterials of complex geometry.Proof-of-principle is first shown by fabricating planar magnetic nanowires raised above the substrate that exhibit controlled domain wall injection and propagation.Secondly,3D artificial spin-ice(3DASI)structures are fabricated,whose complex switching can be probed using optical magnetometry.We show that by careful analysis of the magneto-optical Kerr effect signal and by comparison with micromagnetic simulations,depth dependent switching information can be obtained from the 3DASI lattice.The work paves the way for new materials,which exploit additional physics provided by non-trivial 3D geometries.

Template sacrificial controlled synthesis of hierarchical nanoporous carbon@NiCo_(2)S_(4)microspheres for high-performance hybrid supercapacitors

Binary transition metal sulfides are hotly investigated in advanced energy storage devices because of their ultra-high reversible capacity.Nevertheless,the unsatisfied rate capability and cycling stability still hinder their practical application.Herein,hierarchical nanoporous carbon@NiCo_(2)S_(4)(HNCMs@NCS)composites with coreshell flower-like structures were prepared by in situ growing of NiCo_(2)S_(4) nanosheets on HNCMs through a hydro thermal-as sis ted template sacrificial method.Benefiting from a synergistic effect between the NiCo_(2)S_(4)shell with high specific capacity and the HNCMs with unique porous structure,the synthesized flower-like HNCMs@NCS composites exhibit extraordinary electrochemical performances,including a high capacity of 346.9 mAh·g^(-1)at 1 A·g^(-1),superb rate property with86.4%initial capacity at 30 A·g^(-1)and predominant cycle stability with 81.2%capacity retention after 5000 cycles.Furthermore,the resulting HNCMs@NCS cathode was coupled with the chemical-activated HNCMs(AHNCMs)anode to construct a hybrid supercapacitor device.The asfabricated device exhibits superior energy density(49.9 Wh·kg^(-1)at 802 W·kg^(-1))and ultra-high power density(24 kW·kg^(-1)at 29.5 Wh·kg^(-1)).This fascinating result further demonstrates the tremendous prospect of the synthesized HNCMs@NCS composites as high-performance supercapacitor electrode materials.

Optimization of Manganese and Magnesium Contents in As-cast Aluminum-Zinc-Indium Alloy as Sacrificial Anode

In this study, effects of manganese and magnesium content on the electrochemical properties of Al-Zn-ln sacrificial anode were studied in 0.5 mol/L NaCl solution （pH=5）. The aluminum base alloy with different amounts of Mn and Mg were melted at 750℃, then casted at molds at 25℃. Corrosion experiments were mounted to determine the optimal effect of Mn and Mg on the efficiencies of the aluminum alloy anodes. The corroded and unexposed sample surfaces were subjected to microstructure characterization by optical and scanning electron microscopy. AI-Zn-ln alloy doped with 0%, 0.01%, 0.05%.0.2% and 0.3% by weights of Mn and 0%, 0.5%, 1.0%, 1.5%, 2.0%, 2.5% and 3.0% by weights of Mg were prepared to determine the effect of Mn and Mg on anode efficiency in the environment. The different microstructures of the evolved AI- Zn-ln-Mg-Mn alloy were correlated with the anode efficiencies. The Al-5.0%Zn-2.0%Mg-0.15%Mn-0.02%ln gave the best anode efficiency （about 83%）. The microstructures of the corroded surface of the optimized alloy revealed decreased distribution of the pockets of localized attacks which are characteristics of pitting （or crevice） corrosion.

Influence of yttrium addition on properties of Mg-based sacrificial anode

To improve lower current efficiency of Mg-based sacrificial anode,a Mg-based sacrificial anode material with yttrium addition was investigated.Its electrochemical properties were evaluated by the galvanostatic method,and its microstructure and constitution were characterized by metallurgical microscope and X-ray diffraction.The results showed that,the addition of yttrium refined dentrite grains,maximized current efficiency,and minimized potential of magnesium sacrificial anode.When 0.1% yttrium was doped,the anode showed the highest current efficiency,62.5%,which improved its current efficiency by 14%.

Effects of Binding Energy of Bioinspired Sacrificial Bond on Mechanical Performance of cis-1,4-Polyisoprene with Dual-crosslink

Although bioinspired sacrificial bonds have been demonstrated to be efficient in improving the mechanical properties of polymer materials, the effect of binding energy of a specific dynamic bond on the ultimate mechanical performance of a polymer network with dual-crosslink remains unclear. In this contribution, diamine and sulfur curing package are introduced simultaneously into a sulfonated cis-1,4-polyisoprene to create dually-crosslinked cis-1,4-polyisoprene network with sulfonate-aminium ionic bonds as the sacrificial bonds. Three diamines （primary, secondary and tertiary） with the same spacer between the two nitrogen atoms are used to create the ionic bonds with different binding energies. Although the binding energy of ionic bond does not affect the glass transition temperature of cis-1,4-polyisoprene （IR）, it exerts definite influences on strain-induced crystallization and mechanical performance. The capabilities of diamine in dissipating energy, promoting strain-induced crystallization and enhancing the mechanical performance are in the same order of secondary diamine 〉 primary diamine 〉 tertiary diamine. The variations in mechanical performances are correlated to the binding energy of the ionic bond, which is determined by pKa values.