Wind tunnel test on the effect of metal net fences on sand flux in a Gobi Desert, China

The Lanzhou-Xinjiang High-speed Railway runs through an expansive windy area in a Gobi Desert, and sand-blocking fences were built to protect the railway from destruction by wind-blown sand. However, the shielding effect of the sand-blocking fence is below the expectation. In this study, effects of metal net fences with porosities of 0.5 and 0.7 were tested in a wind tunnel to determine the effectiveness of the employed two kinds of fences in reducing wind velocity and restraining wind-blown sand. Specifically, the horizontal wind velocities and sediment flux densities above the gravel surface were measured under different free-stream wind velocities for the following conditions： no fence at all, single fence with a porosity of 0.5, single fence with a porosity of 0.7, double fences with a porosity of 0.5, and double fences with a porosity of 0.7. Experimental results showed that the horizontal wind velocity was more significantly decreased by the fence with a porosity of 0.5, especially for the double fences. The horizontal wind velocity decreased approximately 65% at a distance of 3.25 m（i.e., 13 H, where H denotes the fence height） downwind the double fences, and no reverse flow or vortex was observed on the leeward side. The sediment flux density decreased exponentially with height above the gravel surface downwind in all tested fences. The reduction percentage of total sediment flux density was higher for the fence with a porosity of 0.5 than for the fence with a porosity of 0.7, especially for the double fences. Furthermore, the decreasing percentage of total sediment flux density decreased with increasing free-stream wind velocity. The results suggest that compared with metal net fence with a porosity of 0.7, the metal net fence with a porosity of 0.5 is more effective for controlling wind-blown sand in the expansive windy area where the Lanzhou-Xinjiang High-speed Railway runs through.

Failure Envelopes of Wide-Shallow Composite Bucket Foundation for Offshore Wind Turbines in Silty Sand

The wide-shallow composite bucket foundation(WSCBF) is a new type of offshore wind power foundation that can be built on land and rapidly installed offshore, there by effectively reducing the construction time and costs of offshore wind power foundation. In this study, the horizontal bearing capacity is calculated by finite element simulation and compared with test results to verify the validity of results. In this process, the vertical load and bending load are respectively calculated by the finite element simulation. Under the vertical load effect, the bucket foundation and the soil inside are regarded as a whole, and the corresponding buckling failure mode is obtained. The ultimate vertical bearing capacity is calculated using empirical and theoretical formulas; the theoretical formula is also revised by finite element results. Under bending load, the rotational center of the composite bucket foundation(in a region close to the bucket bottom) gradually moves from the left of the central axis(reverse to loading direction) to the nearby compartment boards along the loading direction. The H–M envelope line shows a linear relationship, and it is determined that the vertical and bending ultimate bearing capacities can be improved by an appropriate vertical load.

Field Measurements of Influence of Sand Transport Rate on Structure of Wind-sand Flow over Coastal Transverse Ridge

The structure of wind-sand flow under different total sand transport rates was measured with field vertical anemometer and sand trap on the crest of typical coastal transverse ridge in Changli Gold Coast of Hebei Province, which is one of the most typical coastal aeolian distribution regions in China and famous for the tall and typical coastal transverse ridges. The measurement results show that, on the conditions of approximate wind velocities and same surface materials and environments, some changes happen to the structure of wind-sand flow with the increase of total sand transport rate on the crest of coastal transverse ridge. First, the sand transport rates of layers at different heights in the wind-sand flow increase, with the maximum increase at the height layer of 4-8cm. Second, the ratios of sand trans-port rates of layers at different heights to total sand transport rate decrease at the low height layer (0-4cm), but increase at the high height layer (4-60cm). Third, the distribution of the sand transport rate in the wind-sand flow can be expressed by an exponential function at the height layer of 0-40cm, but it changes from power function model to ex-ponential function model in the whole height layer (0-60cm) and changes into polynomial function model at the height layer of 40-60cm with the increase of total sand transport rate. Those changes have a close relationship with the limit of sand grain size of wind flow transporting and composition of sand grain size in the wind-sand flow.

Estimation of Sand Transportation Rate for Fixed and Semi-Fixed Dunes Using Meteorological Wind Data

Taibus County, Inner Mongolia, China, lies in a farming-pastoral ecotone, where severe wind erosion and various aeolian sand hazards are prevalent and fixed and semi-fixed sand dunes occur frequently. This study was conducted to investigate the relationships between sand transportation rate and wind speed for the fixed and semi-fixed sand dunes based on field measurements. The annual quantity of soil erosion by wind was estimated using meteorological wind data. The results indicated that the sand transportation rate in Taibus County in 2000 was 57.38 kg cm-1 year-1 for the semi-fixed dunes and 4.56 kg cm-1 year-1 for the fixed dunes. The total duration of erosive winds covered 12.5% of the time of the year, and spring posed the highest potential of sand transportation. Wind with low speed (≤ 17 m s-1) and high frequency plays a dominant role in sand transportation, while strong wind (≥ 17 m s-1) with low frequency significantly enhanced the sand transportation. Erosive wind speed, directions, and frequency were three crucial dynamic factors influencing sand hazards in the farming-pastoral ecotone. The dominant factors intensifying sand and dust storms in Taibus County might be related to the favorable wind condition in combination with the durable drought, which led to land desertification and vegetation degradation.

On the influence of sand-wind on atmospheric environment

The authors seek, through tests on simulated sand samples in a wind tunnel and analysis of minerals combination and trace elements, to discover the environmental implications of flying-up, falling-down and concentration variation as a function of natural wind speed and direction, distance of movement, range and extent of influence on the atmospheric environment, of micro-granular components on the ground surface in the Keerqin desert area in northwest Liaoning Province of China.

Effect of the W-beam central guardrails on wind-blown sand deposition on desert expressways in sandy regions

Many desert expressways are affected by the deposition of the wind-blown sand,which might block the movement of vehicles or cause accidents.W-beam central guardrails,which are used to improve the safety of desert expressways,are thought to influence the deposition of the wind-blown sand,but this has yet not to be studied adequately.To address this issue,we conducted a wind tunnel test to simulate and explore how the W-beam central guardrails affect the airflow,the wind-blown sand flux and the deposition of the wind-blown sand on desert expressways in sandy regions.The subgrade model is 3.5 cm high and 80.0 cm wide,with a bank slope ratio of 1:3.The W-beam central guardrails model is 3.7 cm high,which included a 1.4-cm-high W-beam and a 2.3-cm-high stand column.The wind velocity was measured by using pitot-static tubes placed at nine different heights(1,2,3,5,7,10,15,30 and 50 cm)above the floor of the chamber.The vertical distribution of the wind-blown sand flux in the wind tunnel was measured by using the sand sampler,which was sectioned into 20 intervals.In addition,we measured the wind-blown sand flux in the field at K50 of the Bachu-Shache desert expressway in the Taklimakan Desert on 11 May 2016,by using a customized 78-cm-high gradient sand sampler for the sand flux structure test.Obstruction by the subgrade leads to the formation of two weak wind zones located at the foot of the windward slope and at the leeward slope of the subgrade,and the wind velocity on the leeward side weakens significantly.The W-beam central guardrails decrease the leeward wind velocity,whereas the velocity increases through the bottom gaps and over the top of the W-beam central guardrails.The vertical distribution of the wind-blown sand flux measured by wind tunnel follows neither a power-law nor an exponential function when affected by either the subgrade or the W-beam central guardrails.At 0.0H and 0.5H(where H=3.5 cm,which is the height of the subgrade),the sand transport is less at the 3 cm height from the subgrade surface than at the 1 and 5 cm heights as a result of obstruction by the W-beam central guardrails,and the maximum sand transportation occurs at the 5 cm height affected by the subgrade surface.The average saltation height in the presence of the W-beam central guardrails is greater than the subgrade height.The field test shows that the sand deposits on the overtaking lane leeward of the W-beam central guardrails and that the thickness of the deposited sand is determined by the difference in the sand mass transported between the inlet and outlet points,which is consistent with the position of the minimum wind velocity in the wind tunnel test.The results of this study could help us to understand the hazards of the wind-blown sand onto subgrade with the W-beam central guardrails.

Flashover Characteristics of Flat Plate Model Under DC Voltage in Wind-sand Condition

The influence of sand dust on discharge of external insulation has caused widespread concern.At present,the research results show wind-sand electricity has a remarkable effect on the discharge characteristics of insulator and has little influence on the discharge characteristics of air gap.The flashover of insulator strings occurs along the insulator surface and air gaps,and the sand dust deposited on the insulator surface may affect the flashover characteristics of insulator strings.This paper studies the flashover characteristics of flat plate model under DC voltage in wind-sand condition.The experimental results show that under positive polarity voltage,the flashover voltage of the flat plate model has a maximum value,while under negative polarity voltage,the flashover voltage of the flat plate model has a minimum value with a certain degree of sand dust deposition.The wind or sand in sand-dust weather has an important effect on the flashover characteristics of the flat plate model.In certain variation range of electric charge,electric charge of sand dust has little effect on the flashover voltage of flat plate model under DC voltage.The deposition of sand has significant influence on the flashover process of flat plate model,which is related to the deposition density and moisture content of sand particle.

A wind tunnel investigation on the transverse motion of aeolian sand

A wind tunnel experiment was performed to investigate aeolian grain motions in the transverse direction, which is perpendicular to the incoming flow and parallels the sand bed. The trajectories in the horizontal plane were recorded by high-speed camera. Statistical analysis of 630 trajectories shows that both the motion orientation and the time-averaged speed follow Gaussian distributions. An exclusive method was used to analyze the driving mechanism. It was concluded that the three-dimensional turbulent air flow, rather than the spin of grain or grain-bed collisions, controls the transverse motion.

Experimental analysis of sand particles' lift-off and incident velocities in wind-blown sand flux

The probability distributions of sand particles＇ lift-off and incident velocities in a wind-blown sand flux play very important roles in the simulation of the wind-blown sand movement. In this paper, the vertical and the horizontal speeds of sand particles located at 1.0 mm above a sand-bed in a wind-blown sand flux are observed with the aid of Phase Doppler Anemometry （PDA） in a wind tunnel. Based on the experimental data, the probability distributions of not only the vertical lift-off speed but also the lift-off velocity as well as its horizontal component and the incident velocity as well as its vertical and horizontal components can be obtained by the equal distance histogram method. It is found, according to the results of the X^2-test for these probability distributions, that the probability density functions （pdf＇s） of the sand particles＇ lift-off and incident velocities as well as their vertical com- ponents are described by the Gamma density function with different peak values and shapes and the downwind incident and lift-off horizontal speeds, respectively, can be described by the lognormal and the Gamma density functions, These pdf＇s depend on not only the sand particle diameter but also the wind speed.

Dynamic Characteristics Analysis on Wind-Blown Sand Ground under Dynamic Compaction Vibration

In the 6000 kN·m energy level dynamic compaction on Inner Mongolia wind-blown sand foundation treatment process, the dynamic characteristics and dynamic response are measured. Vibration action time, vibration main frequency, peak acceleration and peak velocity are analyzed. The vibration acting time is very short, the vertical average vibration acting time increases obviously with distance increasing, and the horizontal average vibration time does hardly change. The main frequency of vibration is at 4.60 - 24.90 Hz, which depends on the soil properties and soil layer distribution. The peak acceleration and peak velocity space distribution are similar. The maximum of horizontal acceleration peak is close to vertical velocity peak, and is near to 51 g under rammer. The maximum of horizontal velocity peak is close to vertical velocity peak, and is near to 54 m/s under rammer. The peak acceleration and velocity are rapidly attenuated, but the vertical peak acceleration and peak velocity are slowly attenuated than horizontal direction. The effective treating depth arrives 13 m for wind-blown wind, peak acceleration is 1.8 g or so, and peak velocity is 2.1 m/s or so. Horizontal treating range is 2.6 times of rammer diameter, and vertical treating range is 5.65 times of rammer diameter.

A Wind Tunnel Investigation of the Shear Stress with A Blowing Sand Cloud

In a blowing sand system,the wind provides the driving forces for the particle movement while the moving particles exert the opposite forces to the wind by extracting its momentum.The wind-sand interaction that can be characterized by shear stress and force exerted on the wind by moving particles results in the modification of wind profiles.Detailed wind pro-files re-adapted to blown sand movement are measured in a wind tunnel for different grain size populations and at differ-ent free-stream wind velocities.The shear stress with a blowing sand cloud and force exerted on the wind by moving par-ticles are calculated from the measured wind velocity profiles.The results suggest that the wind profiles with presence of blowing sand cloud assume convex-upward curves on the u(z)-ln(z) plot compared with the straight lines characterizing the velocity profiles of clean wind,and they can be better fitted by power function than log-linear function.The exponent of the power function ranging from 0.1 to 0.17 tends to increase with an increase in wind velocity but decrease with an increase in particle size.The force per unit volume exerted on the wind by blown sand drift that is calculated based on the empirical power functions for the wind velocity profiles is found to decrease with height.The particle-induced force makes the total shear stress with blowing sand cloud partitioned into air-borne stress that results from the wind velocity gradient and grain-borne stress that results from the upward or downward movement of particles.The air-borne stress in-creases with an increase in height,while the grain-borne stress decreases with an increase in height.The air-borne shear stress at the top of sand cloud layer increases with both wind velocity and grain size,implying that it increases with sand transport rate for a given grain size.The shear stress with a blowing sand cloud is also closely related to the sand transport rate.Both the total shear stress and grain-borne stress on the grain top is directly proportional to the square root of sand transport rate.So,the profound effect of the moving particles on the airflow must be considered in modeling the blown sand movement.With the presence of sand movement,the boundary layer with a blowing sand cloud is no longer a con-stant air shear layer.

Detecting sand-dust storms using a wind-profiling radar

Sand-dust storm is a type of disastrous weather, typically occurring in arid and semi-arid climates. This study selected a region in the hinterlands of the Taklimakan Desert, called the Tazhong region, as the experimental area to quantitatively estimate the particle concentrations of sand-dust storms using the boundary layer wind-profiling radar. We thoroughly studied the radar echo signals and reflectivity factor features during the sand-dust storms. The results indicate that（1） under sand-dust storm conditions, boundary layer wind-profiling radar cannot capture the complete information regarding horizontal wind velocity and direction, but it can obtain the backscattering intensity of sand-dust storms; and（2） during sand-dust storms particle size distributions in the surface layer closely resemble log-normal distributions, with sand-dust particles sizes of 90–100 μm accounting for the maximum particle probability. Retrieved particle size distributions at heights of 600, 800, and 1000 m follow log-normal distributions, and the expected value of particle diameter decreases gradually with increasing height. From the perspective of orders of magnitude, the retrieved results for particle number concentrations and mass concentrations are consistent with previous aircraft-detected results, indicating that it is basically feasible to use boundary layer wind-profiling radar to quantitatively detect the particle concentrations of dust storms.

Prevention and management of wind-blown sand damage along Qinghai-Tibet Railway in Cuonahu Lake area

This paper analyzes the characteristics of climate, geology and geomorphology, vegetation, and sand dune distribution in the Cuonahu Lake area beside the Qinghai-Tibet Railway. The types and causes of railway blown-sand hazards are discussed, and the effectiveness of various sand-controlling measures is assessed. From the perspective of integrated management, a sand-controlling system that combines several engineering measures, including nylon net sand barriers, concrete sand barriers, movable-board sand barriers, sand interception ditches, gravel/rock cover, film sandbags, and permanent vegetation is most beneficial.

Discussion on wind factor influencing the distribution of biological soil crusts on surface of sand dunes

Biological soil crusts are widely distributed in arid and semi-arid regions, whose formation and development have an important impact on the restoration process of the desert ecosystem. In order to explore the relationship between surface airflow and development characteristics of biological soil crusts, we studied surface airflow pattern and development characteristics of biological soil crusts on the fixed dune profile through field observation. Results indicate that the speed of near-surface airflow is the lowest at the foot of windward slope and the highest at the crest, showing an increasing trend from the foot to the crest. At the leeward side, although near-surface airflow increases slightly at the lower part of the slope after an initial sudden decrease at upper part of the slope, its overall trend decreases from the crest. Wind velocity variation coefficient varied at different heights over each observation site. The thickness, shear strength of biological soil crusts and percentage of fine particles at crusts layer decreased from the slope foot to the upper part, showing that biological soil crusts are less developed in high wind speed areas and well developed in low wind speed areas. It can be seen that there is a close relationship between the distribution of biological soil crusts in different parts of the dunes and changes in airflow due to geomorphologic variation.

WINDBREAKS FOR SAND DUNE FIXATION IN JILIN PROVINCE

There are 0.78 million hm2 of sand dune areas in Jilin Province. The effects of two types of windbreaks. shelterbelts and small areas ofartdicial forests, on sand dune fixation were discussed. The temperature, humidity and reduced situation of wind speed in the two types of windbreaks wer systematically studied.

Comparative Analysis of Wind break and Sand fixation Functions of Several Main Forage Plants in Minqin Desert Area

[Objective] The paper was to study wind-break and sand-fixation functions of forage plants in desert area. [Method]Based on the survey data of four major wind-break and sand-fixation plants( Haloxylon ammondendron,Artemisia arenaria,Nitraria tangutorum and Ephedra przewalskii) in Minqin desert area,the longitudinal section area and the sandpile volume of an individual plant and per unit area were calculated. The wind-break and sand-fixation functions of four major plant communities were comparatively analyzed. [Result] The wind-break functions of an individual plant( cluster) successively were N. tangutorum > H. ammondendron > A. arenaria and E. przewalskii; the sand-fixation functions of an individual plant( cluster) successively were N. tangutorum > E. przewalskii; the wind-break functions per unit area successively were A. arenaria > H. ammondendron > N. tangutorum > E. przewalskii; the sand-fixation functions per unit area were N. tangutorum > E. przewalskii; the wind-break and sand-fixation function per unit area were N. tangutorum > A. arenaria > H. ammondendron >E. przewalskii.[Conclusion]A. arenaria can be selected for only wind-break,and N. tangutorum can be chosen for only sand-fixation. If given consideration to both,N. tangutorum and A. arenaria must be selected.

A transport-rate model of wind-blown sand

Sand transport by wind plays an important role in environmental problems.Formulating the sand-transport rate model has been of continuing significance,because the majority of the existing models relate sand-transport rate to the wind-shear velocity.However,the wind-shear velocity readapted to blown sand is difficult to determine from the measured wind profiles when sand movement occurs,especially at high wind velocity.Detailed wind tunnel tests were carried out to reformulate the sand-transport rate model,followed by attempts to relate sand-transport rate to parameters of wind velocity,threshold shear-velocity,and grain size.Finally,we validated the model based on the data from field observations.

Electromagnetic scattering of charged particles in a strong wind-blown sand electric field

Some field experimental results have shown that the moving sands or dust aerosols in nature are usually electrified,and those charged particles also produce a strong electric field in air, which is named as wind-blown sand electric field.Some scholars have pointed out that the net charge on the particle significantly enhances its electromagnetic(EM) extinction properties, but up to now, there is no conclusive research on the effect of the environmental electric field. Based on the extended Mie theory, the effect of the electric field in a sandstorm on the EM attenuation properties of the charged larger dust particle is studied. The numerical results indicate that the environmental electric field also has a great influence on the particle's optical properties, and the stronger the electric field, the bigger the effect. In addition, the charged angle, the charge density, and the particle radius all have a specific impact on the charged particle's optical properties.

Probability of rebound and eject of sand particles in wind-blown sand movement

When incident particles impact into a sand bed in wind-blown sand movement, rebound of the incident particles and eject of the sand particles by the incident particles affect directly the development of wind sand flux. In order to obtain rebound and eject lift-off probability of the sand particles, we apply the particle-bed stochastic collision model presented in our pervious works to derive analytic solutions of velocities of the incident and impacted particles in the postcollision bed. In order to describe randomness inherent in the real particle-bed collision, we take the incident angle, the impact position and the direction of resultant action of sand particles in sand bed on the impacted sand particle as ran- dom variables, and calculate the rebound and eject velocities, angles and coefficients （ratio of rebound and eject velocity to incident velocity）. Numerical results are found in accordance with current experimental results. The rebound and eject liftoff probabilities versus the incident and creeping velocities are predicted.