Single-frequency linearly polarized Q-switched fiber laser based on Nb_(2)GeTe_(4)saturable absorber

We report a single-frequency linearly polarized Q-switched fiber laser based on an Nb_(2)GeTe_(4)saturable absorber(SA).The Nb_(2)GeTe_(4)SA triggers passive Q-switching of the laser,and an un-pumped Yb-doped fiber together with a 0.08-nmbandwidth polarization-maintaining fiber Bragg grating(FBG)acts as an ultra-narrow bandwidth filter to realize singlelongitudinal-mode(SLM)oscillation.The devices used in the laser are all kept polarized,so as to ensure linearly polarized laser output.Stable SLM linearly polarized Q-switching operation at 1064.6 nm is successfully achieved,producing a laser with a shortest pulse width of 1.36μs,a linewidth of 28.4 MHz,a repetition rate of 28.3 kHz-95.9 kHz,and a polarization extinction ratio of about 30 dB.It is believed that the single-frequency linearly polarized pulsed fiber laser studied in this paper has great application value in gravitational wave detection,beam combining,nonlinear frequency conversion,and other fields.

Antimonene-based saturable absorber for a soliton mode-locked and Q-switched fiber laser in the 2 μm wavelength region

We demonstrate antimonene as a saturable absorber(SA) to generate an ultrafast mode-locked and Q-switched laser in the 2 μm wavelength region. The two antimonene-based SAs were prepared and inserted separately in a thulium–holmiumdoped fiber laser to produce the pulsed laser. Antimonene was coated onto a tapered fiber to generate soliton mode-locked pulses and used in thin-film form for the generation of Q-switched pulses. The mode-locking was stable within a pump power of 267 m W–511 m W, and the laser operated at a central wavelength of 1897.4 nm. The mode-locked laser had a pulse width of 1.3 ps and a repetition rate of 12.6 MHz, with a signal-to-noise ratio of 64 d B. Q-switched laser operation was stable at a wavelength of 1890.1 nm within a pump power of 312 m W–381 m W. With the increase in pump power from 312 m W to 381 m W, the repetition rate increased to a maximum of 56.63 k Hz and the pulse width decreased to a minimum value of 2.85 μs. Wide-range tunability of the Q-switched laser was also realized within the wavelength range of1882 nm–1936 nm.

Passively mode-locked erbium-doped fiber laser via a D-shape-fiber-based MoS_2 saturable absorber with a very low nonsaturable loss

We report on the generation of conventional and dissipative solitons in erbium-doped fiber lasers by the evanescent field interaction between the propagating light and a multilayer molybdenum disulfide（MoS_2） thin film. The MoS_2 film is fabricated by depositing the MoS_2 water–ethanol mixture on a D-shape-fiber（DF） repetitively. The measured nonsaturable loss, saturable optical intensity, and the modulation depth of this device are 13.3%, 110 MW/cm^2, and 3.4% respectively.Owing to the very low nonsaturable loss, the laser threshold of conventional soliton is as low as 4.8 mW. The further increase of net cavity dispersion to normal regime, stable dissipation soliton pulse trains with a spectral bandwidth of 11.7 nm and pulse duration of 116 ps are successfully generated. Our experiment demonstrates that the MoS_2-DF device can indeed be used as a high performance saturable absorber for further applications in ultrafast photonics.

Research of a fractional-turn ratio saturable pulse transformer and its application in a microsecond-range pulse modulator

As a combination device for a step-up pulse transformer and a magnetic switch,the saturable pulse transformer is widely used in pulsed-power and plasma technology.A fractional-turn ratio saturable pulse transformer is constructed and analyzed in this paper.Preliminary experimental results show that if the primary energy storage capacitors are charged to 300 V,an output voltage of about 19 kV can be obtained across the capacitor connected to the secondary windings of a fractional-tum ratio saturable pulse transformer.Theoretical and experimental results reveal that this kind of pulse transformer is not only able to integrate a step-up transformer and a magnetic switch into one device,but can also lower the saturable inductance of its secondary windings,thus leading to the relatively high step-up ratio of the pulse transformer.Meanwhile,the application of the fractional-turn ratio saturable pulse transformer in a μs range pulse modulator as a voltage step-up device and main switch is also included in this paper.The demonstrated experiments display that an output voltage with an amplitude of about 29 kV,and a 1.6 μs pulse width can be obtained across a 3500 Ω resistive load,based on a pulse modulator,if the primary energy storage capacitors are charged to 300 V.This compact fractional-turn ratio saturable pulse transformer can be applied in many other fields such as surface treatment,corona plasma generation and dielectric barrier discharge.

Single output LD end-pumped passively mode-locked Nd:YVO_4 laser with semiconductor saturable absorber mirror

A quarter-wave plate and the thin film polarizer （TFP） are used for the LD end-pumped passively mode-locked Nd：YVO4 laser with semiconductor saturable absorber mirror （SESAM） to obtain a single beam output with a total power of 4.8 W. An optical-optical efficiency is achieved to be 24% for a stable CW mode-locking operation at 1064 nm, with a pulse repetition rate of 70 MHz and pulse width of 16 ps. The multipulse in the pulse sequence is eliminated for reaching a peak power as high as 4 kW.

Mode-Locked Erbium-Doped Fiber Laser Using Vanadium Oxide as Saturable Absorber

A mode-locked erbium doped fiber laser（EDFL） is demonstrated using the vanadium oxide（V2O5） material as a saturable absorber（SA）. The V2O5 based SA is hosted into poly ethylene oxide film and attached on fiber ferule in the laser cavity. It shows 7% modulation depth with 71 MW/cm2 saturation intensity. By incorporating the SA inside the EDFL cavity with managed intra-cavity dispersion, ultrashort soliton pulses are successfully generated with a full width at half maximum of 3.14 ps. The laser operated at central wavelength of 1559.25 nm and repetition frequency of 1 MHz.

Q-Switched Raman Fiber Laser with Molybdenum Disulfide-Based Passive Saturable Absorber

We demonstrate a Q-switched Raman fiber laser using molybdenum disulfide （MoS2） as a saturable absorber （SA）. The SA is assembled by depositing a mechanically exfoliated MoS2 onto a fiber ferrule facet before it is matched with another clean ferrule via a connector. It is inserted in a Raman fiber laser cavity with a total cavity length of about 8kin to generate a Q-switching pulse train operating at 1560.2nm. A 7.7-kin-long dispersion compensating fiber with 584 ps.nm-i km-1 of dispersion is used as a nonlinear gain medium. As the pump power is increased from 395 m W to 422 m W, the repetition rate of the Q-switching pulses can be increased from 132.7 to 137.4 kHz while the pulse width is concurrently decreased from 3.35μs to 3.03μs. The maximum pulse energy of 54.3 nJ is obtained at the maximum pump power of 422 roW. These results show that the mechanically exfoliated MoS2 SA has a great potential to be used for pulse generation in Raman fiber laser systems.

High-Power Passively Q-Switched Nd:YAG Laser at 1112 nm with a Cr^(4+):YAG Saturable Absorber

A high-power passively Q-switched Nd：YAG laser operating at lll2nm with Cr4＋：yAO as a saturable absorber is demonstrated. Under 808 nm diode-direct pumping, the maximum average output power of 2.73 W is achieved at the pump power of 16.65 W, corresponding to an optical-to-optical conversion efficiency of 16.4%. At the same time, the pulse width, pulse repetition rate, single pulse energy and peak power are 27.2ns, 9 kHz, 303.3#3 and 11.2kW, respectively. As far as we know, the result gives the highest average output power at 1112nm generated by an 808 nm diode-end-pumped Nd：YAG laser.

Q-Switching Pulse Operation in 1.5-μm Region Using Copper Nanoparticles as Saturable Absorber

We demonstrate a passively Q-switched erbium-doped fiber laser （EDFL） using a copper nanoparticle （CuNP） thin film as the saturable absorber in a ring cavity. A stable Q-switched pulse operation is observed as the CuNP saturable absorber （SA） is introduced in the cavity. The pulse repetition rate of the EDFL is observed to be proportional to the pump power, and is limited to 101.2kHz by the maximum pump power of 113.7mW. On the other hand, the pulse width reduces from 10.19μs to 4.28μs as the pump power is varied from 26.1 mW to 113.7mW. The findings suggest that CuNP SA could be useful as a potential saturable absorber for the development of the robust, compact, efficient and low cost Q-switched fiber laser operating at 1.5-μm region.

Q-Switched Erbium-Doped Fiber Laser Using Cadmium Selenide Coated onto Side-Polished D-Shape Fiber as Saturable Absorber

A stable Q-switched erbium doped fiber laser emitting at 1558 nm is demonstrated using a cadmium selenide（CdSe） material coated onto a side-polished D-shape fiber as the saturable absorber（SA）. By elevating the input pump power from the threshold of 91 mW to the maximum available power of 136 mW, a pulse train with a maximum repetition rate of 57.44 kHz, minimum pulse width of 3.76 us, maximum average output power of7.99 mW, maximum pulse energy of 0.1391 uJ, and maximum peak power of 36.99 mW are obtained. The signalto-noise ratio of the spectrum is measured to be around 75 dB. This CdSe based SA is simple, robust, and reliable,and thus suitable for making a portable pulse laser source.

Interaction of Airy–Gaussian beams in saturable media

Based on the nonlinear Schr o¨dinger equation, the interactions of the two Airy–Gaussian components in the incidence are analyzed in saturable media, under the circumstances of the same amplitude and different amplitudes, respectively. It is found that the interaction can be both attractive and repulsive depending on the relative phase. The smaller the interval between two Airy–Gaussian components in the incidence is, the stronger the intensity of the interaction. However, with the equal amplitude, the symmetry is shown and the change of quasi-breathers is opposite in the in-phase case and out-of-phase case. As the distribution factor is increased, the phenomena of the quasi-breather and the self-accelerating of the two Airy–Gaussian components are weakened. When the amplitude is not equal, the image does not have symmetry. The obvious phenomenon of the interaction always arises on the side of larger input power in the incidence. The maximum intensity image is also simulated. Many of the characteristics which are contained within other images can also be concluded in this figure.

Transition Metal Dichalcogenides(WS2 and MoS2)Saturable Absorbers for Mode-Locked Erbium-Doped Fiber Lasers

We demonstrate an ultrafast fiber laser based on transition metal dichalcogenide materials which are tungsten disulfide (WS2) and molybdenum disulfide (MoS2) as saturable absorber (SA). These materials are fabricated via a simple drop-casting method. By employing WS2, we obtain a stable harmonic mode-locking at the threshold pump power of 184 mW, and the generated soliton pulse has 3.48 MHz of repetition rate. At the maximum pump power of 250 mW, we also obtain a small value of pulse duration, 2.43 ps with signal-to-noise ratio (SNR) of 57 dB. For MoS2 SA, the pulse is generated at 105 mW pump power with repetition rate of 1.16 MHz. However, the pulse duration cannot be detected by the autocorrelator device as the pulse duration recorded is 468 ns, with the SNR value of 35 dB.

Erbium-Doped Zirconia-Alumina Silica Glass-Based Fiber as a Saturable Absorber for High Repetition Rate Q-Switched All-Fiber Laser Generation

We propose and demonstrate a Q-switched erbium-doped fiber laser （EDFL） using an erbium-doped zirconia-alumina silica glass-based fiber （Zr-EDF） as a saturable absorber. As a 16-cm-long Zr-EDF is incorporated into a ring EDFL cavity, a stable Q-switching pulse train operating at 1565？nm wavelength is successfully obtained. The repetition rate is tunable from 33.97？kHz to 71.23？kHz by increasing the pump power from the threshold of 26？mW to the maximum of 74？mW. The highest pulse energy of 26.67？nJ is obtained at the maximum pump power.

Characterization and Saturable Absorption Property of Graphene Oxide on Optical Fiber by Optical Deposition

We prepared graphene oxide（GO） saturable absorber（SA） successfully through optical deposition method, which is a simple but effective approach to deposit various materials onto substrate under the effects of light, and investigated several factors that influence the optical deposition result of GO onto optical fiber end, including poly（methyl methacrylate）（PMMA） concentration, light intensity, light mode, and deposition time. The efficient optically deposited GO preserving its nonlinearity guaranteed by GO/PMMA composite formation was also demonstrated. The GO SA prepared by optical deposition shows superior saturable absorption property with modulation depth and nonsaturable loss of 6% and 40%, respectively.

Nanosecond Pulse Generation with Silver Nanoparticle Saturable Absorber

Nanosecond pulse generation in an erbium-doped fiber laser (EDFL) passively mode-locked by a silver nanoparticle(SNP)-based saturable absorber(SA) is experimentally demonstrated. The SA is fabricated by depositing a nanosized SNP layer onto the surface of polyvinyl alcohol film through the thermal evaporation process. By inserting the SA into an EDFL cavity, stable mode-locked operation is achieved at 1561.5 nm with the maximum pulse energy up to 52.3 nJ. The laser operates at a pulse repetition frequency of 1.0 MHz with a pulse width of 202 ns. These results suggest that SNPs could be developed as an effective SA for mode-locking pulse generation.

Zinc-oxide nanoparticle-based saturable absorber deposited by simple evaporation technique for Q-switched fiber laser

A Q-switched erbium-doped fiber laser(EDFL)incorporating zinc-oxide(ZnO)nanoparticles-based saturable absorber(SA)is proposed and demonstrated.To form the SA,the ZnO nanoparticles,which are originally in the powder form,are first dissolved in ethanol and subsequently deposited onto the surface of fiber ferrule by using the adhesion effect with the evaporation technique.By integrating the ZnO nanoparticle-based SA into a laser cavity of an EDFL,a self-started and stable Q-switching is achieved at a low threshold power of 20.24 mW.As the pump power is increased,the pulse repetition rate is tunable from 10.34 kHz to 25.59 kHz while pulse duration decreases from 21.39μs to 3.65μs.Additionally,this Q-switched laser has a maximum energy per pulse of 19.34 nJ and an average output power of 0.46 mW.These results indicate the feasibility and functionality of the ZnO nanoparticles-based SA for Q-switched generation,which offers the flexibility and easy integration of the SA into a ring laser cavity.

Q-Switched Ytterbium-Doped Fiber Laser Using Black Phosphorus as Saturable Absorber

We demonstrate a Q-switched ytterbium-doped fiber laser （YDFL） using a newly developed multi-layer black phosphorous （BP） saturable absorber （SA）. The BP SA is prepared by mechanically exfoliating a BP crystal and sticking the acquired BP flakes onto a scotch tape. A small piece of the tape is then placed between two ferrules and incorporated in a YDFL cavity to achieve a stable Q-switched operation in a 1.0 μm region. The laser has a pump threshold of 55.1 mW, a pulse repetition rate that is tunable from 8.2 to 32.9 kHz, and the narrowest pulse width of 10.8 μs. The highest pulse energy of 328 nJ is achieved at the pump power of 97.6 mW. Our results show that multi-layer BP is a promising SA for Q-switching laser operation.

Zinc-oxide/PDMS-clad tapered fiber saturable absorber for passively mode-locked erbium-doped fiber laser

We propose and demonstrate a passively mode-locked erbium-doped fiber laser(EDFL)based on zinc-oxide/polydimethylsiloxane(ZnO/PDMS)saturable absorber(SA)that evanescently interacts with the light on a tapered fiber.The ZnO/PDMS composite is coated on the whole surface of the tapered fiber to guarantee the maximum efficiency of the SA device,with a measured insertion loss of 0.87 dB and a modulation depth of 6.4%.The proposed laser can generate soliton mode-locking operation at a threshold power of 33.07 mW.The generated output pulse yields a repetition rate and pulse width of 9.77 MHz and 1.03 ps,respectively.These results indicate that the proposed ZnO/PDMS-clad tapered fiber could be useful as an efficient,compatible,and low-cost SA device for ultrafast laser applications.

Wavelength-Tunable Rectangular Pulses Generated from All-Fiber Mode-Locked Laser Based on Semiconductor Saturable Absorber Mirror

The wavelength-tunable rectangular mode-locking operation is demonstrated in an all-fiber laser based on semi- conductor saturable absorber mirror. As the dissipative soliton resonance signature, the pulse duration varies from 5SOps to 2.1 ns as a function o~ the increasing pump power. Correspondingly, the maximum pulse energy is 9.11 n3. Moreover, it is found that the wavelength tunable operation with a range of approximately 10 nm could be obtained by properly adjusting the polarization controllers. The characteristics of the rectangular pulses at different wavelengths are similar to each other. The demonstration of the wavelength tunable rectangular pulses would be beneficial to some applications for many fields such as spectroscopy and sensing research.

Observation of wavelength-switchable solitons in an all-polarization-maintaining erbium-doped fiber cavity based on graphene saturable absorber reflector

We present the generation of wavelength-switchable single-polarization solitons in an all-polarization-maintaining erbium-doped fiber laser mode-locked by a graphene saturable absorber. Ultrashort pulses centered at the wavelength of 1531.6 nm with the duration of 816 fs and centered at the wavelength of 1557.8 nm with the duration of 402 fs are separately obtained from the same fiber laser cavity. The cavity loss adjusted by the gold reflector plays a crucial role in wavelength switching.