Method of analyzing vibration characteristics of armature system of hermetically sealed electromagnetic relay

Published research is minimal on vibration characteristics of hermetically sealed electromagnetic relay (EMR) ex- posed to mechanical environment. The vibration characteristics of armature system, link contact system with electromagnetic system will cause EMR malfunction. The nonlinear dynamics model of armature systems was studied by considering electro- magnetic attraction force and opposite mechanical force in this paper. Angular displacements of armature under different sinu- soidal vibration conditions are solved in order to obtain the failure mode result from armature system. Vibration tests showed the presented analyzing method is suitable for EMR. The conclusions are instructive for increasing vibration resistance of armature systems of EMR, and are significant for reliability design of switch apparatus.

Design and laboratory evaluation of fog-sealed chip seal on epoxy asphalt pavement for steel bridge deck

In order to improve the surface performace of epoxy asphalt pavement （EAP） for steel bridge deck, an epoxy asphalt chip seal （ ECS） covered by a cationic emulsified asphalt fog seal （i. e., fog-sealed chip seal） isproposed and a laboratory study is conducted to design and evaluate te fog-sealed chip seal. First, the evaluation indices and methods of te chip seal on steel bridge deck pavement were proposed. Secondly, the worst pavement conditions during te maintenance time were simulated by te small traffic load simulation system MMLS3 and the short-term aging test for minimizing the failure probability of chip seal. Finally, the design parameters of fog-sealed chip seal were determined by the experimental analysis and the performance of the designed fog-sealed chip seal was evaluated in thelaboratory. Results indicate that the proposed simulation method of pavement conditions is effective and the maximal load repetitions on the EAPslab specimen are approximately 925 300 times. Moreover, the designed fog-sealedchip sealcan provide a dense surface with sufficient skid resistance,aggregate-asphalt aahesive performance and interlayer shearing resistance.

Transient response of a spherical cavity with a partially sealed shell embedded in viscoelastic saturated soil

Based on Biot’s wave equation, this paper discusses the transient response of a spherical cavity with a partially sealed shell embedded in viscoelastic saturated soil. The analytical solution is derived for the transient response to an axisymmetric surface load and fluid pressure in Laplace transform domain. Numerical results are obtained by inverting the Laplace transform presented by Durbin, and are used to analyze the influences of the partial permeable property of boundary and relative rigidity of shell and soil on the transient response of the spherical cavity. It is shown that the influence of these two parameters is remarkable. The available solutions of permeable and impermeable boundary without shell are only two extreme cases of this paper.

Features of the fault system and its relationship with migration and accumulation of hydrocarbon in Liaodong Bay

The fault system of Liaodong Bay developed extensively under the control of the Tanlu Fault. The fault system can be grouped into strike-slip faults of grade Ⅰ, trunk faults of grade Ⅱand branch faults （induced faults） of grade Ⅲ respectively based on its developmental scale. The faults of grade Ⅰ and Ⅱwere deep, early and large while the faults of grade Ⅲwere shallow, late and small. The formation, evolution and distribution features played a significant role in controlling the migration of oil and gas in both horizontal and vertical directions. The fluid transfer in the fault system occurred in the process of faulting. The strike-slip and trunk faults moved actively forming predominant pathways for oil and gas migration. The branch faults, with weak activity, generally controlled the development of traps and were beneficial for the accumulation and preservation of oil and gas. The faults of grade Ⅰ and Ⅱ formed the major migration pathways for oil and gas, but their fault activity rates appeared to vary along their strikes. The zones with a relatively low fault activity rate might be favorable for oil and gas accumulation. When the activities of strike-slip, trunk, and branch faults came to a halt, the fault seal behavior had a vitally important effect on the accumulation of oil and gas. The controlling role of the fault over fluid distribution was further analyzed by calculating the fault activity quantitatively.

Experimental Verification and Research for the Distortion in the Integrated Frequency Responses of the High-Pressure Sealed Cabin and Magnetic Field Sensor

Although magnetotelluric sounding method applied to the land is advanced, there are many difficulties when it is applied to marine environment, one of which is how to lay magnetic field sensors down to the seafloor to complete measurements. To protect the magnetic field sensors from intense erosion and high pressure, suitable high-pressure sealed cabins must be designed to load them. For the consideration of magnetic measurement and marine operation, the sealed pressure cabin should be nonmagnetic and transportable. Among all optional materials, LC4 super.hard aluminum alloy has the highest performance of price/quality ratio to make the sealed pressure cabin. However, it does not mean that the high-pressure sealed cabin made using LC4 will be perfect in performance. In fact, because of its weak magnetism, the pressure cabin made using LC4 has distorting effect on frequency responses of the magnetic field sensors sealed in it. This distorting effect does not affect the use of the magnetic field sensor, but if we want to eliminate its effect, we should study it by experimental measurements. In our experiment tests, frequency sweep magnetic field as excitation signal was used, and then responses of the magnetic field sensor before and after being loaded into the high-pressure sealed cabin were measured. Finally, normalized abnormal curves for the frequency responses were obtained, through which we could show how the high-pressure sealed cabin produces effects on the responses of the magnetic field sensor. Experimental results suggest that the response distortion induced by the sealed pressure cabin appears on mid- and high-frequency areas. Using experimental results as standardization data, the frequency responses collected from seafloor magnetotelluric measurements can be corrected to restore real information about the seafloor field source.

Structure of Bi_2O_3-ZnO-B_2O_3 system low-melting sealing glass

Bi2O3-ZnO-B2O3 system glass is a kind of lead-free low melting sealing glasses. The structure of Bi2O3-ZnO-B2O3 system low-melting sealing glass was investigated by DSC, FT-IR, XRD and SEM. The results show that with the increase of B2O3 content, the transition temperature Tg and softening temperature Tf of Bi2O3-ZnO-B2O3 system low-melting sealing glasses increase, which leads to the liquid phase precipitation temperature increasing and promotes the structure stability in the glass. With increasing the heat treatment temperature, a large number of liquid phases appear in samples and the sinter efficiency of the samples increases. The FT-IR spectra of the glasses show the presence of some bands that are assigned to vibrations of Bi--O bond from [BO3] pyramidal and [BiO6] octahedral units and B--O from [BO3] and [BO4] units. With the decrease of B203 content, the crystallization tendency of the glass increases. In glass samples Bl and B〉 crystallization starts at 460 ℃ and 540 ℃, respectively. Both of them precipitate Bi24B2O39 phases.

Sealing Features of Fluid-Rock System and its Control on Acidic Dissolution in Cretaceous Sandstone Reservoirs,Kuqa Subbasin

The Cretaceous Bashijiqike Formation is the main gas-bearing strata in the northern structural deformation zone of Kuqa subbasin. The acidic dissolution of this formation arose at 5-4Ma, which corresponds to the late burial stage of the Bashijiqike Formation. Variability of interlayer due to rock composition is negligible. Differentiation of acidic dissolution in sandstones was controlled by difference in amount of exogenous acid fluid from underlying strata. For the absence of sedimentary and structural carrier system between the isolated sandstone reservoirs, most fluid-rock systems show relative sealing feature during later burial stage by sealing feature of formation pressure, geochemical characteristics of formation water and content of diagenetic products in sandstones. Variation of sealing effects for different fluid-rock systems is obvious. The pressure coefficient is inversely proportional to acidic dissolved porosity of sandstone reservoirs, indicating that the variation of sealing effects for fluid- rock system mainly controls the differentiation of acidic dissolution.

A single institution experience using the LigaSure vessel sealing system in video-assisted thoracoscopic surgery for primary spontaneous pneumothorax

This study sought to report our 6-year experience with the LigaSure vessel sealing system（LVSS） in videoassisted thoracoscopic surgery（VATS） for primary spontaneous pneumothorax.A series of 180 consecutive patients with primary spontaneous pneumothorax were operated on in our institution from May 2005 to December 2010.Intraoperatively,large lesions（bullae or blebs） with a diameter more than 2 cm were resected by staplers,and the residual lesions were treated by LVSS.LVSS was also used to ablate the apical area when no lesions were found.Conventional apical pleural abrasion was done in all cases.All patients were successfully treated using VATS with minimal perioperative bleeding.The mean operating time was 76 minutes（range,43-160 minutes） for single-side procedures and 169 minutes（range,135-195 minutes） for bilateral procedures,the mean number of applied staples was 1.93 per patient（range,0-8 days）,the duration of drainage was 3.8 days（range,2-15 days）,and the duration of hospital stay was 5.8 days（range,3-16 days）.Postoperative complications included persistent air leak（〉 5 days） in 11 cases（6.1%） and residual pneumothorax in 6（3.3%）.None required reoperation.The mean duration of follow-up was 57 months（range,24-105 months）.Recurrence was seen in three cases（1.7%）,and all underwent another operation thereafter.None of the lesions in the relapse cases received ablation with LVSS in the first operation.LVSS can optimize VATS for primary spontaneous pneumothorax and reduces the use of single-use staples.The method is safe,easy to use,and cost-effective and produces satisfactory results.

Assessment of sealed fire states by fire characteristic

The paper presented assessment of sealed fire states in underground coal mines by so-called 'fire characteristic', which graphically described tendencies of fire gas components-oxygen, nitrogen, carbon dioxide, carbon monoxide and hydrocarbons-in time. In order to mark gas components tendencies in time the authors applied the time series analysis. The case studied confirmed, that analysis of fire gas components tendencies in time and their correlation allow to elicit proper conclusions about fire state assessment. Assessment of fire states based on single value of fire indexes without considering their trends in time and correlation between trends of gas components would give wrong results The suggested method can appropriately indicate fire states in a sealed area.

Preparation and property of self-sealed plasma electrolytic oxide coating on magnesium alloy

Plasma electrochemical oxidation (PEO) is a surface modification technology to form ceramic coatings on magnesium alloys However,its application is limited due to its defects.This work reports a novel preparation of in-situ sealing of PEO coatings by four-layer voltage and sol addition.The morphology and structure were characterized by scanning electron microscopy (SEM),energy dispersive X-ray spectroscopy (EDS),and X-ray diffractometer (XRD).Image-Pro Plus 6.0 was used to determine the porosity of the coating,which was decreased from 8.53%to 0.51%.Simultaneously,the coating thickness was increased by a factor of four.The anti-corrosion performance of each sample was evaluated using electrochemical tests,and the findings revealed that the corrosion current density of coatings (i_(corr)) of the samples were lowered from 9.152×10^(-2) to 6.152×10^(-4) mA·cm^(-2),and the total resistance (R_(T)) of the samples were enhanced from 2.19×10^(4) to 2.33×10^(5)Ω·cm^(2).The salt spray test used to simulate the actual environment showed that corrosion points appeared on the surface of the coating only at the 336 h.In addition,the mechanism of PEO self-sealing behavior was described in this article.

Research of chamber local dry underwater welding system and drainage properties

Because of relatively large protective area and good underwater welding quality, chamber underwater welding has a great using prospect in spent fuel pool maintenance at nuclear power plant. A chamber local dry automatic underwater welding test system with a data acquisition platform is developed, drainage seal tests in a water tank are carried out and the data acquired from the tests are analyzed. The results show that the chamber local dry underwater welding test system can achieve good drainage seal, the drainage effect is enhanced with the increase of the drainage gas flow rate and the drainage time. The results establish the foundation of the research of chamber local dry underwater welding.

Formation of overpressure system and its relationship with the distribution of large gas fields in typical foreland basins in central and western China

Based on the data of measured formation pressure, drilling fluid density of key exploration wells and calculated pressure by well logging, combined with the analysis of natural gas geological conditions, the characteristics and formation mechanisms of formation fluid overpressure systems in different foreland basins and the relationship between overpressure systems and large-scale gas accumulation are discussed.(1) The formation mechanisms of formation overpressure in different foreland basins are different. The formation mechanism of overpressure in the Kuqa foreland basin is mainly the overpressure sealing of plastic salt gypsum layer and hydrocarbon generation pressurization in deep–ultra-deep layers, that in the southern Junggar foreland basin is mainly hydrocarbon generation pressurization and under-compaction sealing, and that in the western Sichuan foreland basin is mainly hydrocarbon generation pressurization and paleo-fluid overpressure residual.(2) There are three common characteristics in foreland basins, i.e. superimposed development of multi-type overpressure and multi-layer overpressure, strong–extremely strong overpressure developed in a closed foreland thrust belt, and strong–extremely strong overpressure developed in a deep foreland uplift area.(3) There are four regional overpressure sealing and storage mechanisms, which play an important role in controlling large gas fields, such as the overpressure of plastic salt gypsum layer, the overpressure formed by hydrocarbon generation pressurization, the residual overpressure after Himalayan uplift and denudation, and the under-compaction overpressure.(4) Regional overpressure is an important guarantee for forming large gas fields, the sufficient gas source, large-scale reservoir and trap development in overpressure system are the basic conditions for forming large gas fields, and the overpressure system is conducive to forming deep to ultra-deep large gas fields.

EIS Characterization of Sealed Anodic Oxide Films on Titanium Alloy Ti-10V-2Fe-3Al

Anodic oxide films grown on titanium alloy Ti-10V-2Fe-3Al in the solution of sodium tartrate, then sealed in boiling deionised water and calcium acetate solution were observed by using field emission scanning electron microscopy （FE-SEM）, and were chemically analysed by using energy dispersive spectroscopy （EDS）. Corrosion behaviour was investigated in a 3.5% sodium chloride solution, using electrochemical impedance spectroscopy （EIS）. The morphology of the anodic oxide films was dependent on the sealing processes. The surface sealed in calcium acetate solution presented a more homogeneous and smooth structure compared with that sealed in boiling deionised water. The corrosion resistance of the oxide films sealed in calcium acetate solution was better than that sealed in boiling deionised water.

Contact performance analysis of pressure controller's sealing interface in deep in-situ pressure-preserved coring system

The sealing performance of contact interfaces plays the most important role in the design and operation of the in-situ pressure-preserved coring system.To meet the demand of ultra-high pressure-retained coring for oil and gas exploration in deep reservoirs,a quantitative analysis of the contact mechanical behavior of the pressure controller was performed.Based on the micro-contact theory of rough surfaces,a three-dimensional numerical model of the rough contact interface between the valve cover and the valve seat was constructed,and the micro-contact behavior of the metal contact surfaces was comprehensively studied.The results show that the actual contact area of the valve interface increases with the increase of surface roughness before the critical contact point,but decreases after that.Compared with the real contact model with double rough surfaces,although the simplified hard-contact model with a single rough surface can reflect the micro-contact behavior of the rough surface to a certain extent,it cannot truly reveal the microchannel morphology between the sealing interfaces under pressure.Therefore,the realistic double-rough-surface model should be recommended to evaluate the sealing performance of coring tools,particularly for high pressure conditions.The material properties of valves have a significant effect on the contact characteristics of rough surfaces,which suggested that the actual contact area decreases with the increase of the elastic modulus of the contact material under the same loading conditions.The knowledge of this work could help to enhance the seal design of pressure controllers for in-situ pressure-preserved coring.

Clinical uses of ligasure vessel sealing system (LVSS) in surgery

This article provides the efficacy of the new device, Ligasure Vessel Sealing System（LVSS） for achieving hemostasis. LVSS is an alternative to suture ligatures, hemoclips, staplers, for ligating vessels and tissue bundles. This new device seals the vessels up to 7 mm in diameter by denaturing collagen and elastin within vessel wall and surrounding connective tissue.

The research of the evaluation system for the sealability of hydraulic supports and jacks＇ seals

In order to enhance the sealing quality and assemble efficiency of hydraulic supports, the evaluation system for the sealability of the hydraulic support and jack＇s seals was established through the testing and experimenting technology in respects, such as seals＇ dimensions, reasonable amounts of compression, sealability, life, resistance to pressure, etc. Through life detecting test of the seal, found the longest life seal ring under the same conditions, and through the reciprocating test of the hydraulic support, found the most appropriate amount of interference between the groove and the seal ring, thus, to decrease the leakage and extend the life span of the hydraulic support.

Protection Performance of Plasma Sprayed Al_(2)O_(3)-13 wt%TiO_(2) Coating Sealed with an Organic-inorganic Hybrid Agent

An organic-inorganic hybrid sealing agent was fabricated and used in the plasma sprayed Al_(2)O_(3)-13 wt%TiO_(2)coating,and conventional silicone agent was also used for comparison.Protection performance of the coatings was comprehensively evaluated based on both anti-corrosion and anti-biofouling properties.The results reveal that the sealing treatment is remarkably useful to decrease the porosity of the coating,and the porosity of the coating sealed with the hybrid agent is only 0.035%.Immersion corrosion test and Tafel polarization test reveal that the sealed coating with the hybrid agent exhibits a better corrosion resistance by compared with the coating sealed with silicone agent.The corrosion current density i_(corr) of the hybrid agent sealed coating is only 0.7×10^(-6)A·cm^(-2).Moreover,anti-biofouling tests both in the outdoor analogue hydraulic environment and in the natural marine environment prove that the mentioned novel coating presents a better combination of corrosion resistance and anti-biofouling property by compared with the other coatings,and it could be used as a protection of metal components in the marine environment.

Direct measurement of oxygen consumption rates from attached and unattached cells in a reversibly sealed, diffusionally isolated sample chamber

Oxygen consumption is a fundamental component of metabolic networks, mitochondrial function, and global carbon cycling. To date there is no method available that allows for replicate measurements on attached and unattached biological samples without compensation for extraneous oxygen leaking into the system. Here we present the Respiratory Detection System, which is compatible with virtually any biological sample. The RDS can be used to measure oxygen uptake in microliter-scale volumes with a reversibly sealed sample chamber, which contains a porphyrin-based oxygen sensor. With the RDS, one can maintain a diffusional seal for up to three hours, allowing for the direct measurement of respiratory function of samples with fast or slow metabolic rates. The ability to easily measure oxygen uptake in small volumes with small populations or dilute samples has implications in cell biology, environmental biology, and clinical diagnostics.

Aircraft Clean Air Requirements Using Bleed Air Systems

There are certification and airworthiness requirements relevant to the provision of clean breathing air in the crew and passenger compartments. There have been continuing reports and studies over the years regarding oil fumes in aircraft, including impaired crew performance. Oil fumes are viewed in varying ways ranging from rare seal bearing failures, to low level leakage in normal flight. A Masters of Science (MSc) research degree was undertaken to assess whether there is any gap between the certification requirements for the provision of clean air in crew and passenger compartments, and the theoretical and practical implementation of the requirements using the bleed air system. A comprehensive literature search reviewed applicable certification standards, documented and theoretical understanding of oil leakage. Two types of interviews were conducted to address the research questions. Key aviation regulators were questioned about the process by which they certify and ensure compliance with the clean air requirements. Aerospace engineers and sealing professionals were interviewed about their understanding of how oil may leak past compressor oil bearing seals, and into the air supply under various flight conditions. The outcome of the research showed that there is a gap between the clean air certification requirements, and the theoretical and practical implementation of the requirements using the bleed air system. Low level oil leakage into the aircraft cabin in normal flight operations is a function of the design of the engine lubricating system and bleed air systems, both utilising pressurised air. The use of the bleed air system to supply the regulatory required air quality standards is not being met or being enforced as required.

A pressure-calibration method of wavelength modulation spectroscopy in sealed microbial growth environment

A new pressure-calibration method for calibrating the reduction of second harmonic(2f)amplitude caused by pressure broadening effect in sealed microbial growth environment is present.The new method combines with linewidth compensation and modulation depth compensation and makes the 2f amplitude accurately retrieve metabolic CO_(2) in microbial growth.In order to verify the method,a simulation experiment is developed,in which the increasing CO_(2) concentration leads to the increasing pressure.Comparing with the relation between the traditional 2f amplitude and gas concentration,there is a monotonous relation between the calibrated 2f amplitude and CO_(2) concentration,particularly,a linear relation is present when the CO_(2) concentration is replaced with the CO_(2) particle number.In terms of microbial measurement,the growth of Escherichia coli is measured,and the culture bottle is sealed during the microbial growth process.The experimental results show that,comparing to the microbial growth retrieved by traditional 2f amplitude,the calibrated 2f amplitude can accurately retrieve microbial growth in sealed environment.